Tender For Construction Of Itbp Banquet Hall At 39Th Bn Itbp, Greater Noida, Up (Sh-4 : Roofing Work, Water Suppy And Sanitary Installation Etc.)
Tender Value
2.33 Crore
Estimated cost
Bid Submission
31 Aug 2026
6 days left
EMD
4.66 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ghaziabad → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Itbp Banquet Hall At 39Th Bn Itbp, Greater Noida, Up (Sh-4 : Roofing Work, Water Suppy And Sanitary Installation Etc.)
BOQ
| Sl. No. | Item Description |
| 1 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 2 | Providing at all heights, levels and locations Aluminium profile industrial troughed sheet of Alloy 31500/31000/40800, conforming to IS 1254, IS 737, IS 2676. The sheet shall be fixed using self drilling/self tapping SS screws of size 5.5x65 mm with EPDM seal complete upto required pitch in horizontal, vertical or curved surfaces including cutting to size and shape where required as per specifications, detail drawings and direction of Engineer-in-Charge. The rate shall be inclusive of all screws, seal, ridge, labour, scaffolding, machinery for fixing and approved sealent where required etc. but excluding the cost of purlins, rafters and trusses. 0.71 mm thick (precoated or as per sample approved by Engineer-In-Charge) the profile detail width 1044/920 mm, cover width 1000/875 mm. |
| 3 | Supply, fabrication and insttallation of self supported arch shaped roofing as per specifications mentioned below:The Steel Sheet shall be 3'-0\\" (914MM) width(tolerance +/- 3.00 MM) which shall be curved and molded at site using mechanical press and dies to the desired curves and shape to form 2'-0\\"(605MM) approximate wide interlocking panels. These panels shall be erected in position and their seams shall be interlocking and pressed to close the seam forming a water tight joint. Minor color chipping. scratching should be rectified by applying Epoxy Lacquer . Neccesary Arrangement including the supply for installation of fasteners at the end will be in the scope of vendor.a) Make any of the following from the international Market only ZAC License Maker www.galvalume.com • Thyssen Krupps , Germany• Dongbu Steel Co. Limited , Korea• Corus Steels , U.K.• Yeih Phui Steel Ltd. , Taiwan• Dofasco Steels, U.K. • Bethelehem Steels, USA b) Technical Details• Standard – Color coated GALVALUME steel Complying to ASTM A792• Base Metal Thickness – 1.60 MM (Tolerance as +/0.02MM)• Total Coated Thickness – 1.675 MM (Tolerance as +/0.02MM) • Alloy Coating – AZ 150( Aluminium 55% , Zinc 43.5%, Silicon 1.5%)• Yield Strength – 350 MPA• Paint Coating – Regular Modified Polyester . Top coat 25 Micron& Bottom Coat 12 Micron• Color Pattern – Combination of Blue and White(Ratio –50% each) |
| 4 | Supply and Installation of Galvalume Light Hangers for Electrical conduits and light hanging purpose, Point Load of 20 Kgs Each. |
| 5 | Supply and Installtion of Wind Operated Turbo Ventilators Aluminum Construction, Size 24\\", Capacity 2300 CFM, With Complete Fixing Accessories. |
| 6 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board |
| 7 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. |
| 8 | Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge. |
| 9 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 10 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm |
| 11 | Providing and fixing CP Jali 125 mm nominal dia. |
| 12 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 25 mm dia |
| 13 | Supplying of shower curtain |
| 14 | Providing and fixing manual 25 ltr Gyzer in Washing area (Make Jaquar/ Bajaj/ Crompton as per the sample approved by Engineer-In-Charge) |
| 15 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (Make Jaquar/Kohler as per the sample from approved brand) |
| 16 | Providing and fixing braided hose 450mm long for gyesers (as per the sample from approved brand) |
| 17 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150X150mm Square Shape (Make Jaquar/Kohler Jaquar ABS Body Chrome Plated as per the sampleapproved by Engineer-In-Charge)) |
| 18 | Providing Fixing CP brass shower set comprising of CP brass single lever Shower mixe with spout, shower arm, shower rose complete including cutting and making good the wall etc. Shower mixer with spout (Make: Jaquar Cat. No. COP-273NPM or equivalent or as per sample from approved brand) |
| 19 | Providing and fixing 600 mm\\" long C.P. brass towel reck Jaquar make complete (Make Jaquar/Kohler as per the sample from approved brand) |
| 20 | Providing and fixing Single piece slim concealed cistern body with control plate Jaquar make complete in all respect.in bridals rooms (Make Jaquar/Kohler as per the sample from approved brand) |
| 21 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. (Make Jaquar/Kohler as per the sample from approved brand) |
| 22 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge (Make Jaquar/Kohler as per the sample from approved brand) |
| 23 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore (Make Jaquar/Kohler as per the sample from approved brand) |
| 24 | Providing and fixing health faucet with 8mm dia 1.2 meter long flexible tube and wall hook (Make Jaquar/Kohler as per the sample from approved brand) |
| 25 | Providing and fixing toilet paper holder : C.P. brass (Make Jaquar/Kohler as per the sample from approved brand) |
| 26 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (Make Jaquar/Kohler as per the sample from approved brand) |
| 27 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630X450 mm with a pair of 15 mm C.P. brass pillar taps (Make Jaquar/Kohler as per the sample from approved brand) |
| 28 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. (Make Jaquar/Kohler as per the sample from approved brand) |
| 29 | Providing and fixing Soap Dish -SS304, Chrome Plated Jaquar make complete in bridals rooms (Make Jaquar/Kohler as per the sample from approved brand) |
| 30 | Providing and fixing CP Towel ring square Jaquar make complete in bridals rooms (Make Jaquar/Kohler as per the sample from approved brand) |
| 31 | Providing and fixing F/F Conceable body for single lever basin mixer wall mounted consisting of oprating lever, wall flange with exposed parts Jaquar make complete (Make Jaquar/Kohler as per the sample from approved brand) |
| 32 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. (Make Jaquar/Kohler as per the sample from approved brand) |
| 33 | Providing and fixing wall mounted recess hand dryer complete including fixing on wall with PVC rawl plug and CP brass screw complete. in common toilets and bridal room (Make Jaquar as per the sample from approved brand) |
| 34 | Providing and fixing liquid Soap dispensers in the toilets (Make Jaquar/Kohler as per the sample from approved brand) |
| 35 | Providing and fixing soil, waste and vent pipes : 100 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 36 | Providing and fixing soil, waste and vent pipes : 75 mm diameter : Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 37 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysSep 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender