Tender For Special Repair To Certain Buildings At Rayang Mil Stn
Tender Value
1.21 Crore
Estimated cost
Bid Submission
16 Sep 2026
9 days left
EMD
1.96 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Siang → Arunachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Certain Buildings At Rayang Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinfoced) in ground floor,paving nexc 15mm thick (below or above GL) complete all as specified and directed |
| 2 | Demolition Cement Concrete (Reinforced) in any Position not otherwise specifically provided for and Removing Debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed. |
| 3 | Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. complete all as specified and as directed. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. complete all as specified and as directed |
| 5 | M&L 25mm thick cement concrete as in Sub-base in cement concrete type B0 1:2:4 using 12.5mm graded stone aggregate as in floor, finished fair and even (toilet & bathroom sunken portion) or any where as required, complete all as specified and as directed. |
| 6 | S&F Non - skid coloured ceramic tiles of size 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, skirtings etc set and jointed in neat cement slurry and pointed in white or coloured cemert to match including screed bed or bedding layers of mortar 15mm thick for laying floor finishes in CM 1:4 complete all as specified and as directed. |
| 7 | M&L non-skid ceremic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm, in floors, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles including for screed bed (or) bedding layer of morter 15 mm thick for laying floor finishes CM (1:4) complete all as specified and directed. |
| 8 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 9 | Demolition/dismantling of stone slabs/paver blocks and tiles of any description or thickness laid bedded and pointed in any mortar in floors, approns etc. and clean the surface to receive screed bed to lay new tiles complete all as specified |
| 10 | M&L for machine cut kota stone slab flooring 20-25mm thick with white marble/yellow jaisalmer stone as borders/motifs over & including 20 mm thick screed bed in CM 1:3 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed . |
| 11 | M & L for mirror polishing on marble/kota stone where ever required to give high gloss finished complete |
| 12 | M&L for 75mm thick plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed . |
| 13 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 14 | S&F mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails , fixed with angle cleats or other connecting plates, gusset plates, etc conforming to Gde Fe-410-W (Gde E- 250) quality 'B' complete all as specified & directed. |
| 15 | S&F rolled MS anlgles/joists/girders (Fe-290 gde E-165) as in staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc complete all as specified and directed. |
| 16 | M&L preparation of new or previously untreated steel surfaces exc 10 cm width or girth and applying two coat of synthetic enameled paint over one coatof red oxide primer complete all as specified and directed. |
| 17 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, incl nanital or similar pattern roof covering. |
| 18 | S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 19 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/ridges/cladding to wall, fixed with self tapping screws/Aluminium screws complete all as specified and directed. |
| 20 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets |
| 21 | M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Alumi nium framework with screws and S & F of Anodised aluminium snap grid frame work of size 605 x 605 mm in Ceiling, all as per specification and drawing of MES Schedule for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 22 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc. 1.50sqm & not exc 4.00 sqm each and removing from site complete all as specified and directed. |
| 23 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exc. 1.5 sq. m each each and removing from site complete all as specified and directed. |
| 24 | Taking down Shutters of any description exc 1 sq. M and n exc 2 sqm each and removing from site complete all as specified and directed. |
| 25 | Factory made single extruded WPC (Wood Plastic Composite) Frames/Chowkhat of size 50mm X 75mm, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for (separately) complete all as specified by the manufacturer and as per directions of Engineer-in-charge |
| 26 | Factory made single extruded WPC (Wood Plastic Composite) solid plain flush door shutter of 25 mm size calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)complete as specified by the manufacturer and as per directions of Engineer- in-charge. (For W.C. and bathroom door shutter). |
| 27 | S&F 35mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type with both faces are covered with decorative face veneer with lipping/frame to match, complete all as specified & directed. |
| 28 | M&L mild steel work in framed work to Door Chowkats (angle in any section as desired),grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors and similar work conforming to Fe 290 Gde E-165 |
| 29 | S&F second class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed. |
| 30 | S&F-in-repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed. |
| 31 | S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates, shutters etc including joining cleat for fixing etc. complete all as specified & directed. |
| 32 | S&F of 4.00mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified & directed. |
| 33 | S&F of 4.00mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane ccomplete all as specified & directed. |
| 34 | S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, side locks etc. complete all as specified & directed. |
| 35 | S&F 150 mm size MS door spring including roller and roller plate by means of welding or screwing down complete all as specified & directed. |
| 36 | S&F door stopper 100 mm of aluminium alloy body with rubber bottom complete all as specified and directed. |
| 37 | S&F aluminium handles, cast type, anodised of size 150 mm complete all as specified & directed. |
| 38 | S&F Aluminium anodised, barrel tower bolts of extruded section 200 long complete all as specified and directed . |
| 39 | S&F aluminium alloy, anodised, sliding door bolt 300mm long with hasp, stapple (bolt type) and fixing clips of sheet, cast or extruded sections complete all as specified and directed . |
| 40 | S&F 100mm size, mild steel butt hinges, medium weight cold rolled complete all as specified and as directed. |
| 41 | M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new or previously untreated wooden surfaces exc 10cm girth or girth incl preparation of new wooden surfaces complete all as specified and directed. |
| 42 | S&F in repair vitreous China squatting pan 'Orissa' pattern of size 580mmx440mm white with integral foot rest (excluding flushing cistern) but including PVC (SWR) 'P' trap set in and including lime concrete complete all as specified and directed |
| 43 | S&F for Vitreous china EWC (P trap) , white in colour with & including PVC seat cover , CP or aluminised hinging device (excluding flushing cisten & flush pipe) complete all as specified and directed by Engr-in-Charge. |
| 44 | S & F in repairs health faucet (CP Brass head) with 1.5m tube and hook all as directed. |
| 45 | S&F in repair PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet ball valve, float and handle including waste pipe and brackets all as specified. |
| 46 | S&F in repair PVC connections 15 mm size with PTMT nuts of length 450mm long. |
| 47 | S&F in repairs 15mm bore Stop cock/angle cock fancy type, cast copper alloy, chromium plated with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 48 | S&F in repairs rotational moulded polyethylene water storage tanks of 1000 ltr capacity double layers (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed. |
| 49 | S&F in repairs 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed. |
| 50 | S&F 25mm bore CPVC Ball Valve fixed complete all as specified and directed. |
| 51 | S&Fin repair 15 mm Bib taps, chromium plated fancy typewith crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified. |
| 52 | S & F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified. |
| 53 | Taking down old steel tubing & connection including cleaning for refixing for 20mm bore pipe complete all as specified & directed. |
| 54 | Taking down old steel tubing/PP-R pipes & connection including cleaning for refixing for 25/32mm bore pipe complete all as specified & directed. |
| 55 | Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceilings or laying on floorof size outer dia 20mm complete all as specified & directed. |
| 56 | Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceilings or laying on floorof size outer dia 25 mm complete all as specified |
| 57 | S & F, in repairs for vitreous china wash basin white flat back, size 550x300mm incl brackets and pedestal cutting for and pinning in ends or brackets. complete all as specified & directed. |
| 58 | S & F in repairs Brass chromium plated shower rose 125mm size swivel type. |
| 59 | S & F in repairs tubular towel rail brass chromium plated, 20mm dia, D type 60 cm long between flanges.complete all as specified and directed |
| 60 | S & F in repair of brass CP wall mixer for shower including , mixing of hot & cold water screwed down for iron pipe of 20 mm dia complete all as specified and directed |
| 61 | S & F in repair PTMT grating doom 100mm dia (minimum weight 25gms) complete all as specified and directed |
| 62 | S & F in repairs pillar taps (fancy type) cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for union pipe and fixed to 20 mm dia pipe complete all as specified & directed. |
| 63 | S&F in repairs PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement. complete all as specified & directed. |
| 64 | S & F in repairs glass corner shelf, one set comprises of three pieces of corner shelf fancy type (small to large) 250 x 250mm, 200 x 200mm, 150 x 150mm) with all fittings,complete all as specified & directed. |
| 65 | S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws,complete all as specified. |
| 66 | S & F in repairs 32mm dia Waste fittings brass chromium plated for glazed wash basins etc with long screwed shanks and fly nuts, flanged end, bedded in red lead cement all as directed. |
| 67 | S & F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)complete all as specified & directed. |
| 68 | Taking down eaves gutters and rain water pipe,soil waste and vent pipe 75/110mm with fittings of any size complete all as specified and directed |
| 69 | Demolition and breaking up drain pipe (SGSW, AC, RCC or PVC) of 150mm bore incl demolition of PCC as in benching and hauching etc complete all as specified and directed. |
| 70 | Excavating in trenchs not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation and getting out in hard dense soil complete all as specified and directed. |
| 71 | S&F PVC (SWR) 160mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with PVC/Rubber Ring Joints, with or without Ears, laid in Trenches, etc., complete all as specified and as directed. |
| 72 | M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to Drain Pipes of 160mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and tested; complete all as specified and as directed.NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items. |
| 73 | M&L Cutting into Existing Manholes for Connecting New Drain Pipes of 160mm (Internal dia), Making Good to Pipe and Rendering, Cutting out Existing Benching for and Forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed. |
| 74 | S&F 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvent laid in trenches or in floors complete all as specified and directed. |
| 75 | S&F 75mm PVC (SWR) pipes(ISI Marked) single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 76 | S& F 75 mm PVC (SWR) bends of any radius complete all as specified and directed |
| 77 | S& F 75 mm PVC (SWR) tee equal or unequal complete all as specified and directed |
| 78 | Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/ loose soil.. |
| 79 | Removing Excavated soils to a distance exc 1.5 Km but not exc 5.0 Km and depositing where directed at a level not exc1.5 M above the starting point. |
| 80 | S&F for 110mm bore door type PVC (SWR) bends any radius complete all as specified and directed |
| 81 | S&F 110mm PVC (SWR) junction single, (Single T) equal or unequalcomplete all as specified and as directed. |
| 82 | S&F in repairs 110 mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 83 | M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like |
| 84 | M&L precast RCC 1:2:4 type B1 as in landings, cover slab,chajjas etc.and similar articles with plain faces set in CM 1:6, complete all as specified & directed. |
| 85 | S & F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.complete all as specified & directed. |
| 86 | Formwork for soffits of slab,such as roof slab, floor slab, landings and similar works not exceeding 200 mm thick, finished rough surfaces of concrete, complete all as specified & directed. |
| 87 | Use and waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cmwide, complete all as specified and directed. |
| 88 | M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix ( using 20mm graded aggregate), exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 89 | Taking down cement or cement lime plaster of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 90 | M&L rendering 15mm thick on fair faces of brick work or concrete surfaces in cm 1:6, complete all as specified. |
| 91 | M&L for preparation of new plastered surfaces of wall and appling two coats cement base paint complete all as specified. |
| 92 | S&F in repair Stainless Steel Curtain Rail/ Rod having 20mm Outer dia and 1.0mm Wall thickness including Brackets, Side Holders and Rings, etc. and Fixed-in-repairs, complete all as specified and as directed.NOTE :- (a) Stainless Steel Decorative Finials and Stainless Steel Brackets will be provided for Each Length of Curtain Rail/ Rod and Cost of the same will deemed to be included in the Quoted Unit Rate.(b) Only Length of Curtain Rail/ Rod will be Measured for Payment. |
| 93 | Demolition/dismantling of stone slabs/paver blocks and tiles of any description or thickness laid bedded and pointed in any mortar in floors, approns etc. and clean the surface to receive screed bed to lay new tiles complete all as specified & directed. |
| 94 | M&L for 75 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base for receiving floor finishes complete all as specified & directed. Please Enable Macros to View BoQ information |
| 95 | M&L for 75 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base for receiving floor finishes complete all as specified & directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysSep 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender