Tender For Repair / Maintenance Of Water Supply Rising Main Pipe Including Cleaning Of Overhead Tanks, Open Well, Bore Well Along With Certain Other Connected Works In Domestic Area At Af-I, 309 Tru And Af-Ii Under Ge (Af) Jamnagar No.2
Tender Value
40 Lakhs
Estimated cost
Bid Submission
09 Sep 2026
16 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jamnagar → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Maintenance Of Water Supply Rising Main Pipe Including Cleaning Of Overhead Tanks, Open Well, Bore Well Along With Certain Other Connected Works In Domestic Area At Af-I, 309 Tru And Af-Ii Under Ge (Af) Jamnagar No.2
BOQ
| Sl. No. | Item Description |
| 1 | M & L for Cleaning of RCC under ground sump of capacity 1.5 Lakh Gallon at depth of 3mtr by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls, allowing applied coat to become dry and wait for confirmation from MES Staff, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed for the following locations as under :- |
| 2 | Main Pump House |
| 3 | MAP Pump House |
| 4 | DSC Pump House |
| 5 | M & L for Cleaning of RCC under ground sump of capacity 2.0 Lakh Gallon at depth of 3mtr by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls,allowing applied coat to become dry and wait for confirmation from MES Staff , writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed for the following locations as under :- |
| 6 | Main Pump House |
| 7 | AF-II Filtration Plant |
| 8 | M & L for Cleaning of RCC under ground sump of capacity 1.0 Lakh Gallon at depth of 2.5mtr by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls,allowing applied coat to become dry and wait for confirmation from MES Staff, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed for the following locations as under :- |
| 9 | AF-II Filtration Plant |
| 10 | AF-II Pump House |
| 11 | M & L for Cleaning of RCC under ground Raw Water sump of capacity 5 Lakh Gallon at depth of 4.5mtr by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls, allowing applied coat to become dry and wait for confirmation from MES Staff, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed for the following locations as under:- |
| 12 | AF-II Filtration Plant |
| 13 | M&L for Cleaning of RCC under ground sump of capacity 5000 litre at depth of 2mtr by removing sludge, mud or any other foreign material from the bottom and internal surface of tank by wire brushing, cleaning with fresh water, bailing out complete water with pump sets, washing of internal surface with sufficient quantity of water & bleaching powder (0.10 Kg of bleaching powder will be mix in 1 litre water), finally applying two coats of lime washing on entire internal surface, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed. |
| 14 | M&L for Cleaning of RCC over head water tank of capacity 10,000 / 15,000 Gallons at 12 metre height by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls, allowing applied coat to become dry and wait for confirmation from MES Staff, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed. |
| 15 | M&L for Cleaning of RCC over head water tank of capacity 25,000 Gallons at 18 metre height by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls,allowing applied coat to become dry and wait for confirmation from MES Staff, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed for the following locations as under :- |
| 16 | Premnagar OHT |
| 17 | New Officers OHT |
| 18 | M&L for Cleaning of RCC over head water tank of capacity 40,000 / 50,000 Gallons at 18 metre height by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls, allowing applied coat to become dry and wait for confirmation from MES Staff, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed for the following locations as under :- |
| 19 | Old Officers OHT |
| 20 | Sardar OHT |
| 21 | New Super OHT |
| 22 | AF-II OHT |
| 23 | M & L for Cleaning of RCC over head water tank of capacity 1,00,000 Gallons at 18 metre height by removing sludge, mud or any other foreign material from the bottom and internal wall surface of tank by means of wire brush and spraying of cleaned fresh water, bailing out accumulated dirty water inside the tank with pump sets, removal of deposited muds and other sediments, washing of internal surface with sufficient quantity of mixture in suitable proportion (0.10 Kg of bleaching powder will be mix in 1.0 litre water), finally applying two coats of lime washing on entire internal surface of walls, allowing applied coat to become dry and wait for confirmation from MES Staff, writing the date of cleaning and capacity of tank with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed for the following locations as under :- |
| 24 | Old Project OHT |
| 25 | M&L for cleaning of DSC open well of size 10 metre x 8 metre and 12 metre depth (filled with accumulated sediments, sludge and foreign particles etc upto 1.6 metre height from bottom, & balance portion filled with water up to 12 metre height from bottom of well) by continues dewatering till the complete water is removed from the open well by using suitable capacity non clog diesel engine pump set and cleaning of all the accumulated sediments, sludge and foreign particles up to bottom of open well & removing the same to a distance exc 250 metre but not exceeding 500 metre and depositing where directed by Engr in Charge. |
| 26 | Note for item No 1 to 9 :- (i) Dewatering process shall be continuous as per working hrs provn of standby arrangement of another pumping set on failure of working pump set shall be arranged by contractor. (ii) Adequate skilled man power shall be employed for cleaning. (iii) All protective arrangement / instrument during cleaning and dewatering shall be provided by contractor deemed to be included in the cost of cleaning. (iv) Work shall be executed by experienced persons in trade and all safety precautions as per CP norms will be ensured during cleaning of open well / UG sump / Overhead tank by the contractor. (v) An intimation will be given to Engr in charge before execution and after completion of work. |
| 27 | M&L for Cleaning of 500 to 1000 litre capacity HDPE service water tank of and the connected circulating pipes at any position by removing sludge, mud, moss, moulds, efflorescent salts, oil spots etc or any other foreign material from the bottom, cover and internal surfaces by scraping using wire brush, draining out the water from the tank and washing internally with water & bleaching powder (0.10 Kg of bleaching powder will be mix in 1 litre water) and again draining out the water from the tank and writing the date of cleaning with white synthetic enamel paint on black background with synthetic enamel paint complete all as specified and directed. |
| 28 | Excavation in trenches in soft/loose soil n.exc 1.5 mtr wide & n.exc 1.5mtr in depth and n. exc. 10sqm on plan for laying pipe in trenches and getting out in soft / loose soil complete all as specified and directed. |
| 29 | Returning filling in trenches, spreading, levelling, watering and well ramming in layers n.exc 25cm in hard dense soil complete all as specified and directed. |
| 30 | Removing of surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above starting point complete all as specified and directed. |
| 31 | S&F in repairs GI tubing medium grade, ISI Marked conforming to IS:1239 Part-I 2004, 20mm bore with and including all fittings such as bends, elbows,tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and directed.Make: Jindal/Tata steel/Prakash surya |
| 32 | S&F in repairs GI tubing medium grade, ISI Marked conforming to IS:1239 Part-I 2004, 25mm bore with and including all fittings such as bends, elbows,tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and directed.Make: Jindal/Tata steel/Prakash surya |
| 33 | S&F in repairs GI tubing medium grade, ISI Marked conforming to IS:1239 Part-I 2004, 40mm bore with and including all fittings such as bends, elbows,tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and directed.Make: Jindal/Tata steel/Prakash surya |
| 34 | S&F in repairs GI tubing medium grade, ISI Marked conforming to IS:1239 Part-I 2004, 50mm bore with and including all fittings such as bends, elbows,tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and directed.Make: Jindal/Tata steel/Prakash surya |
| 35 | S&F and testing in replacement of 150mm bore, DI water mains (including all fittings) with spigot and socket ends and rubber tytan joints Class K-9 in any length laid in trenches complete all as specified and directed. |
| 36 | S&F and testing in replacement of 100mm bore, DI water mains (including all fittings) with spigot and socket ends and rubber tytan joints Class K-9 in any length laid in trenches complete all as specified and directed. |
| 37 | Supply and Fix in repair HDPE pipe with material grade PE 100, PN 10.0 confirming to IS-4984 ISI Marked for working pressure 10Kg/sqcm including taking out old unsv damaged pipe complete all as specified and directed. Make: Kisan/Supreme |
| 38 | Outer dia 90mm with minimum wall thickness 6.7mm |
| 39 | Outer dia 110mm with minimum wall thickness 8.1mm |
| 40 | Supply and Fix in repair submersible pump cable, PVC insulated, PVC sheathed, multi stranded copper conductor cable 1100 volts grade and connecting complete including taking out old unsv damaged cable of following sizes:-Make: Finolex / Havells / KEI |
| 41 | 6sqmm 3 core |
| 42 | 10sqmm 3 core |
| 43 | Supply & fix in repair of cast iron Sluice valve PN1.6 as per IS-14846, body, dome, wedge-CI IS:210, rings-bronze IS:318, Spindal-SS IS:6603, Gland Packing greasy jute packing, fasteners-CS, Gasket- Natural rubber, nominal size as under, both ends flanged in existing line, after removal of old unserviceable sluice valve without damaging to existing pipe line complete all as specified and directed for the following . Make: Kirloskar / Kartar/Zoloto. Note : Suitable size flanges for existing pipe line, Joints and jointing materials shall be included under this item. |
| 44 | 80mm dia |
| 45 | 100mm dia |
| 46 | 150mm dia |
| 47 | Supply and fix in repair high pressure, heavy duty cast iron non return valve/ check valve of following sizes, conforming to BS 1868, Class 600, suitable to hydrostatic test pressure for body 156 kg/sq cm & for seat 115 kg/sq cm, both ends flanged in existing line, after removal of old unserviceable non return valve without damaging to existing pipe line complete all as specified and directed for the following .Make Kirloskar / Kartar/ Zoloto. Note : Suitable size MS flanges for existing pipe line, Joints and jointing materials shall be included under this item. |
| 48 | 150mm dia |
| 49 | 100mm dia |
| 50 | 80mm dia |
| 51 | 50mm dia |
| 52 | 40mm dia |
| 53 | 25mm dia |
| 54 | 20mm dia |
| 55 | S & F in repair Cast iron foot valve confirming to IS:4038 with rubber seating, flanged end complete incl taking out old unsv complete all as specified and directed for the following .Make: Kartar/Venus/Zoloto |
| 56 | 150 mm bore |
| 57 | 100 mm bore |
| 58 | 80 mm bore |
| 59 | Supply and Fix in repair cast iron butter fly valve, with both end flanged type, conforming to IS 13095 with nuts bolts and washers of suitable size and necessary rubber gaskets etc for following sizes complete incl taking out old unsv complete all as specified and directed for the following .Make: Kartar/Venus/Kirloskar/Zoloto |
| 60 | 100 mm bore |
| 61 | 150 mm bore |
| 62 | 200 mm bore |
| 63 | M & L for disconnecting electrical connection & outlet pipe connection, taking out submersible pump and motor of any capacity from the tube well / borewell lowered at the depth of 100m and above from the ground level complete with HDPE pipe and submersible cable, transported to authorized work shop for repair / servicing, transported back to existing location and lowering the same pump after repairing / servicing along with HDPE pipe and electric cable including fixing of cable to pipe with PVC strip, replacement of clamps and mild steel bolts, nut and washers with stainless still nut and bolt, casing capping bell cap etc, connecting electrical connecting & delivery pipe line complete all as specified and directed. Note: (i) Repairing/Servicing of Submersible pump & motor shall be measured & paid separately. (ii) Cable & HDPE pipe if found unserviceable shall be measured & paid separately as Supply & fix. |
| 64 | M & L for Repairing / Servicing of unserviceable submersible pump of cap 5 HP to 12.5 HP by dismantling the pump and taking out defective / unsv / worn out parts of submersible pump set and replacement / servicing of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 65 | Stainless steel Shaft as per existing dia incl metaling of pump shaft, grinding & polishing |
| 66 | Thrust plate |
| 67 | Bearings as per existing (02 nos in each) with bearing sleeve |
| 68 | Neck Ring |
| 69 | Oil seal |
| 70 | Non return valve cast iron |
| 71 | Impeller or diffuser stainless steel as per casing dia |
| 72 | Bearing bush made of rubber |
| 73 | M & L for Repairing / Servicing of unserviceable electric motor cap of 5HP to 12.5 HP couplled to submersible pump, AC 3 phase, by dismantling the motor and coupling pulley and sent to work shop for repair. Removal of existing burnt out copper winding wire, cleaning of slots using suitable reagents and rewinding with super enamelled copper winding wire of appropriate gauge to achieve required RPM, varnsihing, drying, ovening, overhauling, greasing, painting and assembling the same after complete repair, connecting with pump and making necessary electrical connection and testing of motor after installation complete all as specified and directed. Note: Contractor shall be responsible for maintaining required RPM after repair, non compliance of speed considered as incomplete repair. |
| 74 | M & L for Repairing / Servicing of unserviceable 15 HP to 20 HP capacity submersible pump by dismantling the pump and taking out defective/unsv/worn out parts of submersible pump set and replacement/servicing of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 75 | Thrust plate |
| 76 | Distance sleeves |
| 77 | Bearings as per existing (02 nos in each) with bearing sleeve |
| 78 | Stage Ball |
| 79 | Oil seal |
| 80 | Non return valve cast iron |
| 81 | Stainless steel filter cage |
| 82 | Impeller or diffuser stainless steel as per casing dia |
| 83 | Alignment of pump impeller with motor shaft |
| 84 | M & L for Repairing / Servicing of unserviceable electric motor cap of 15HP couplled to submersible pump, AC 3 phase, by dismantling the motor and coupling pulley and sent to work shop for repair. Removal of existing burnt out copper winding wire, cleaning of slots using suitable reagents and rewinding with super enamelled copper winding wire of appropriate gauge to achieve required RPM, varnsihing, drying, ovening, overhauling, greasing, painting and assembling the same after complete repair, connecting with pump and making necessary electrical connection and testing of motor after installation complete all as specified and directed. Note: Contractor shall be responsible for maintaining required RPM after repair, non compliance of speed considered as incomplete repair. |
| 85 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity 3 to 5 HP, single phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils / winding, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 86 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity of 7.5 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly ,cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils/ winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 87 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity 10.0 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly ,cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils/ winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 88 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity of 15 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils / winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 89 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity 20 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils/ winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 90 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity 30 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils / winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 91 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity 40 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils / winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 92 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity 50 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils / winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 93 | M&L for Dismantling of existing defective/unsv squirrel cage induction motor of capacity 75 / 100 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, providing insualtion and reassembling stator and rotor, connecting coils/ winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed. |
| 94 | M&L for Repairing / Servicing of unserviceable centrifugal pump set of suitable capacity couplled with 7.5HP to 15 HP electric motor by dismantling the pump and taking out defective/unsv/worn out parts of pump set and replacement of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 95 | Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE |
| 96 | Oil / water seal / Mechanical seal assembly |
| 97 | Alignment of pump impeller with motor shaft |
| 98 | lantern ring |
| 99 | Impeller lock nut |
| 100 | Gland |
| 101 | Coupling with rubber bush as per existing |
| 102 | Pump Gasket |
| 103 | Shaft sleeve |
| 104 | Pump wear ring and Pump shoulder ring |
| 105 | M&L for Repairing / Servicing of unserviceable centrifugal pump set of suitable capacity couplled with 20 HP electric motor by dismantling the pump and taking out defective/unsv/worn out parts of pump set and replacement of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 106 | Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE |
| 107 | Oil / water seal / Mechanical seal assembly |
| 108 | Alignment of pump impeller with motor shaft |
| 109 | lantern ring |
| 110 | Impeller lock nut |
| 111 | Gland |
| 112 | Coupling with rubber bush as per existing |
| 113 | Pump Gasket |
| 114 | Shaft sleeve |
| 115 | Pump wear ring and Pump shoulder ring |
| 116 | M&L for Repairing / Servicing of unserviceable centrifugal pump set of suitable capacity couplled with 30HP electric motor by dismantling the pump and taking out defective/unsv/worn out parts of pump set and replacement of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 117 | Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE |
| 118 | Oil / water seal / Mechanical seal assembly |
| 119 | Alignment of pump impeller with motor shaft |
| 120 | lantern ring |
| 121 | Impeller lock nut |
| 122 | Gland |
| 123 | Coupling with rubber bush as per existing |
| 124 | Pump Gasket |
| 125 | Shaft sleeve |
| 126 | Pump wear ring and Pump shoulder ring |
| 127 | Key for coupling |
| 128 | Gland Packing |
| 129 | O ring |
| 130 | M&L for Repairing / Servicing of unserviceable centrifugal pump set of suitable capacity couplled with 40HP electric motor by dismantling the pump and taking out defective/unsv/worn out parts of pump set and replacement of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 131 | Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE |
| 132 | Oil / water seal / Mechanical seal assembly |
| 133 | Alignment of pump impeller with motor shaft |
| 134 | lantern ring |
| 135 | Impeller lock nut |
| 136 | Gland |
| 137 | Coupling with rubber bush as per existing |
| 138 | Pump Gasket |
| 139 | Shaft sleeve |
| 140 | Pump wear ring and Pump shoulder ring |
| 141 | Key for coupling |
| 142 | Gland Packing |
| 143 | O ring |
| 144 | M&L for Repairing / Servicing of unserviceable centrifugal pump set of suitable capacity couplled with 50HP electric motor by dismantling the pump and taking out defective/unsv/worn out parts of pump set and replacement of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 145 | Repairing of shaft by remetaling/welding, grinding and polishing |
| 146 | Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE |
| 147 | Oil / water seal / Mechanical seal assembly |
| 148 | Impeller or diffuser stainless steel as per casing dia |
| 149 | Alignment of pump impeller with motor shaft |
| 150 | Lantern ring |
| 151 | Impeller lock nut |
| 152 | Terminal box cover |
| 153 | Gland |
| 154 | Coupling with rubber bush as per existing |
| 155 | Pump Gasket |
| 156 | Shaft sleeve |
| 157 | M&L for Repairing / Servicing of unserviceable centrifugal pump set of suitable capacity couplled with 75 / 100HP electric motor by dismantling the pump and taking out defective/unsv/worn out parts of pump set and replacement of all defective parts as under and reassebling the pump set including testing complete all as specified and directed. |
| 158 | Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE |
| 159 | Oil / water seal / Mechanical seal assembly |
| 160 | Alignment of pump impeller with motor shaft |
| 161 | Impeller lock nut |
| 162 | Gland |
| 163 | Coupling with rubber bush as per existing |
| 164 | Pump Gasket |
| 165 | Shaft sleeve |
| 166 | Pump wear ring and Pump shoulder ring |
| 167 | Key for coupling |
| 168 | Gland Packing |
| 169 | S&F in repair Bronze gate valve class-1 for 15mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, complete all as specified and directed. |
| 170 | S&F in repair Bronze gate valve class-1 for 20mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, complete all as specified and directed. |
| 171 | S&F in repair Bronze gate valve class-1 for 25mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, complete all as specified and directed. |
| 172 | S&F in repair Bronze gate valve class-1 for 40mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, complete all as specified and directed. |
| 173 | S&F in repair Bronze gate valve class-1 for 50mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, complete all as specified and directed. |
| 174 | M&L for cleaning of pump houses, surrounding area by surface excavation upto 10 cm depth incl removing shrubs, grass, miniplants and other unwanted materials and levelling complete in soft/loose soil all as specified and directed. Please Enable Macros to View BoQ information |
| 175 | M&L for cleaning of pump houses, surrounding area by surface excavation upto 10 cm depth incl removing shrubs, grass, miniplants and other unwanted materials and levelling complete in soft/loose soil all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysSep 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender