Tender For Proposed Construction Of Plastic Waste Manegement Unit In Karajgaon Tq. Bhokardan Dist.Jalna.
Tender Value
3.04 Lakhs
Estimated cost
Bid Submission
04 Sep 2026
11 days left
EMD
30500
Bank guarantee accepted
Document Fee
3050
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalna → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Proposed Construction Of Plastic Waste Manegement Unit In Karajgaon Tq. Bhokardan Dist.Jalna.
BOQ
| Sl. No. | Item Description |
| 1 | A) WORK PORTION |
| 2 | Item No 1 Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, manual dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. 0.4320 Cum x 44No = 19.008 |
| 3 | Item No 2 Providing dry trap/ granite/ quartzite/ gneiss,rubble stone soling in 15 cm to 20 cm thicklayers including hand packing and compacting, etc. complete. |
| 4 | Item No 3 Providing and laying in situ 1:2:4 (M-150) grade of C.C. of trap/granite/quartzite/gneiss metal for foundation and bedding including dewatering. Form work compacting and curing. Finishing etc. complete with initial lift of 1.5 M below/above ground level. |
| 5 | Item No 4 Providing and casting in situ C.C. of trap/ granite/ quartzite / gneiss metal of approved quality for RCC works as perdetailed drawings and designs or asdirected by Engineer-in-charge including normal dewatering, centering,form work,compaction, finishing the formed surfaces with C.M. 1:3 of sufficient minimum thickness to give a smooth andeven surface wherever necessary orroughening if special finish is to be provided and curing, etc. complete. (Byweigh batching and mix design for M-250and M-300 only. Use of L&T, A.C.C.,Ambuja, Birla Gold, Manikgad, Rajashree,etc. cement is permitted.) (Excluding)For Footing |
| 6 | Item No 5 Providing and casting in situ C.C. of trap/ granite/ quartzite / gneiss metal of approved quality for RCC works as perdetailed drawings and designs or asdirected by Engineer-in-charge including normal dewatering, centering,form work,compaction, finishing the formed surfaces with C.M. 1:3 of sufficient minimum thickness to give a smooth andeven surface wherever necessary orroughening if special finish is to be provided and curing, etc. complete. (Byweigh batching and mix design for M-250and M-300 only. Use of L&T, A.C.C.,Ambuja, Birla Gold, Manikgad, Rajashree,etc. cement is permitted.) (Excluding) |
| 7 | Item No 6;- Providing and casting in situ C.C. of trap/ granite/ quartzite / gneiss metal of approved quality for RCC works as perdetailed drawings and designs or asdirected by Engineer-in-charge including normal dewatering, centering,form work,compaction, finishing the formed surfaces with C.M. 1:3 of sufficient minimum thickness to give a smooth andeven surface wherever necessary orroughening if special finish is to be provided and curing, etc. complete. (Byweigh batching and mix design for M-250and M-300 only. Use of L&T, A.C.C.,Ambuja, Birla Gold, Manikgad, Rajashree,etc. cement is permitted.) (Excluding) |
| 8 | Item No 7 Providing Autoclaved Aerated Concrete Block masonary of conforming toIS:2185(Part3) -1984 in extra fine jointing mortar of fixo block of UltraTech or equivalent in superstructure including striking joints,raking out joint sand scaffolding etc.Complete.(The test shall be carried out conforming to IS:6441 (Part I) - 1972) |
| 9 | Item No.8 Providing and laying Rough Shahabad Stone Flooring 25mm to 30mm thick and of required width in plain/diamond pattern on abed of1:6C.M.including cement float,striking joints, pointing in cement mortar 1:3 curing and cleaning etc. complete. |
| 10 | Item No.9 Providing structural steel work in single stanchions composed of RSJ, channel,etc. with caps, bases, mild steel plates,angles, brackets, cleats, gusset plates,anchor bolts, etc. as per detailed design and drawing or as directed by Engineer inchargeincluding cutting, fabrication,hoisting, erecting, fixing in position, makingriveted / bolted / welded connections andone coat of anticorrosive paint and over it two coats of oil painting, etc. complete. (Bd |
| 11 | Item No.10 Providing sand faced plaster externally in cement mortar using approved screened sand,in all positions including base coat of 15mm thick in cement mortar1:4 using waterproofing compounda to 1Kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6to8 mmthick in cement mortar1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. |
| 12 | Item No.11 Providing and applying three coats of water proof cement paint of approved manufacture and of approved colour to new plastered surfaces including scaffolding if necessary,cleaning and preparing the surface, watering for two days etc. complete. |
| 13 | Item No.12 Providing and fixing plain zinc sheeting of 0.80mm thick (22B.W.G.) over the ridge hip or valley to galvanized iron sheet roofing including all fastening and bolt galvanised ironscrews and bolts, lead and bitumen washers etc. complete.(Weight of 6.8 Kilogram/sq.m.). |
| 14 | Item No.13 Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9mm with lockplate of 3.15mmthickness reinforced with 35x35x5mm angle section fitted with sliding bolts and handles for bothsides,deep M.S.channel section of depth and thickness not less than 65mmand3.15mm respectively withhold fast arrangements ,M.S.Bracket plate300x300x3.15mm minimum size and shape with squarebar ,suspension shaft of minimum 32mm diameter,hoodcover of M.S.sheet not lessthan 0.9mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc.complete. (I.S.62481979) (Without mechanical gear) |
| 15 | Item No.14 Providing and fixing board displaying information,such as'Name of work,Tender cost ,Name of Contractor,Work completion and liability period etc', having rectangular shape of1.20mx0.90m size made out 18gauge (1.25mm) thick mildsteel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stovee name lonbackside and border/ messages /symbol setc.with approved colour shade paint complete,on M.S.angle of size 35x35x3mm frame with properly crossbraced M.S.angles of size 35mmx35mmx3mm duly painted including Two M.S.angle iron posts of size 65mmx65mmx6mm, 3.65m long painted with alternate black and white bands of 25cm width including all fixtures etc.and fixing the boards in1:4:8concrete block of size 60cmx60cmx75cm including ,excavation ,refilling ,transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge |
| 16 | Item No.15 Providing and fixing in position steel bar reinforcement of various diameters for RCC piles, caps, footings, foundations,slabs, beams, columns, canopies,staircases, newels, chajjas, lintels, pardies,copings, fins, arches, etc. as per detailed designs, drawings and schedules;including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required, etc. complete(including cost of binding wire). (Bd-F- |
| 17 | Machinery Charges Provision for Providing Machinery |
| 18 | GST Charges |
| 19 | Item No.1 Provision for GST Charges |
| 20 | MISCELLANEOUS WORK |
| 21 | Item No.1:- Providing, erecting and giving test of L.T.Line with all necessary material and labour charges. MSEDCL Quotation, Connection Charges and 1.3% supervision Charges paid to MSEDCL as per estimate approved by MSEDCL Officer etc. complete. (Note:- Payment will be paid to Contractor as per MSEDCL Estimate & work done approved by Engineer in charge.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender