Tender For Provision Of 01 Toilet Block, Provn Of Complaint Cell At Dinjan And Provn Of 01 Toilet At Outpocket Mil Stn Under Ge Dinjan No.2
Tender Value
22.50 Lakhs
Estimated cost
Bid Submission
09 Sep 2026
12 days left
EMD
45000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Provision Of 01 Toilet Block, Provn Of Complaint Cell At Dinjan And Provn Of 01 Toilet At Outpocket Mil Stn Under Ge Dinjan No.2
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n.exc 30 cm deep and averaging 15 cm deep geeting out in soft/loose soil. |
| 2 | Excavating in trenches, n. exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. and getting out in soft/loose soil complete in all respect as specified and directed |
| 3 | M&L for PCC (1:4:8) type D2 (using 40mm crushed and graded stone aggregate) as in foundaion and mass filling complete in all respect as specified and directed |
| 4 | M & L full brick work with Old Size Cement boned Bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:6) complete in all respect as specified and directed. |
| 5 | M & L brick work with sub-class \\"B\\" old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:6) complete in all respect as specified and directed |
| 6 | M & L brick work sub class B, class designation 75 old size bricks, straight or curved on plan exceeding 6 m mean radius built in CM 1:4 complete in all respect as specified and directed. |
| 7 | M & L for half brick work with sub-class \\"B\\" old size bricks of class designation 75, straight or curved on plan built in CM (1:4) complete in all respect as specified and directed |
| 8 | M & L for half brick work with old size Cement bonded bricks of CD 75, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:4 complete in all respect as specifified and directed. |
| 9 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete in all respect as specified and directed. |
| 10 | Removing excavated material n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete in all respect as specified and directed. |
| 11 | M&L 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:6, finished even & smooth without using extra cement complete in all respect as specified and directed. |
| 12 | M & L 15mm thick plastering on brick/stone/concrete surafces of wall in cement mortar (1:4) finished even and smooth without using extra cement complete in all respect as specifified and directed. |
| 13 | M&L 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:4, finished even & smooth without using extra cement including mixing of water proofing compound complete in all respect as specified and directed.(Note: Water proofing compound shall be measured and paid under supply only item) |
| 14 | Supply only integral water proofing compound complete in all respect as specified and directed. Note : Water Proofing compund shall be mixed as per manufacturer's instructions. |
| 15 | M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc. .complete in all respect as specified and directed. |
| 16 | Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; complete in all respect as specifified and directed. |
| 17 | Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in columns, posts, struts etc. complete in all respect as specifified and directed. |
| 18 | Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in beams, lintels, etc.; complete in all respect as specifified and directed. |
| 19 | Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in chajjas, etc. complete in all respect as specifified and directed. |
| 20 | M&L for PCC 1:2:4 type B 1 (using 20mm nominal size crushed and graded stone aggregate) as in surface channels & drains complete in all respect as specified and directed. |
| 21 | Providing and laying for cement concrete in coping, hold fasts using type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) or of similar work, etc. including necessary form work complete in all respect as specifified and directed. |
| 22 | M & L pre cast RCC (1:2:4) type B-1 using 20 mm nominal size crushed and graded stone aggregate in cover slabs or of similar items including necessary cutting, form work etc.cement complete in all respect as specified and directed. |
| 23 | Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like ; complete in all respect as specifified and directed. |
| 24 | M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter in rough finished flat surface of concrete complete in all respect as specifified and directed. |
| 25 | M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished flat surface of concrete complete in all respect as specifified and directed. |
| 26 | M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. in rough finished flat surface of concrete complete in all respect as specifified and directed. |
| 27 | M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc. 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work in rough finished flat surface of concrete complete in all respect as specifified and directed. |
| 28 | S & F 10mm dia and over TMT bar cut to length bent to shape required, including cranking, bending spiarlly for hooping for colums, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete in all respect as specified and directed. |
| 29 | M & L for deformed TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete in all respect as specifified and directed. |
| 30 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using FE-410W (Grade E-250 quality \\"A\\") complete all as specified and directed. |
| 31 | S & F pre- painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws with bituminous washer complete in all respect as specified and directed. |
| 32 | S & F pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge or valley gutter or of similar type used in roofs fixed with self tapping screws with bitumen washers complete in all respect as specified and directed. (to be measured as flat) |
| 33 | S&F steel work in tubular/square/rectangular hollow section/angle iron, tee etc. for structural trusses including special shaped washer etc. complete using ERW or induction butt welded tubes using Fe as per IS 4923, Grade YST 310 including necessary machinery for upto 10m height structure complete in all respect as specified and directed. |
| 34 | S & F plate girder or single stanchions, built up of one beam or channel section with flange plates, caps bases, splices, agnle brackets cleats and other connection confirming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed. |
| 35 | M & L for preparation of new undecortaed wall surfaces and applying two coats of cement base paint over a coat of alkali resistant priming paint on external surfaces of walls complete in all respect as specified and directed. |
| 36 | M&L for preparaing new un decorated plastered or unplastered surface of wall and apply three coats of white wash complete in all respect as specified and directed. |
| 37 | Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs.The frame shall be covered with fiber glass from all sides.M.S. stay shall be provided at the bottom to steady theframe., complete as specified by the manufacturer and as per directions of Engineer-in-charge. |
| 38 | S & F for Factory made single extruded WPC (wood polymer composite) solid door/ window / ceosetory windows & other frames / chowkhat of size 65x150 mm comprising of virgin PVC polymer of K value 58-60 (suspension Grade), calcium carbonate and natural fibers (wood power / rice husk /wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having maximum frame density of 750 kg / cum, screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum comprssive strength of 58 N / mm², Modules of elasticity 900 N / mm² and resistance to spread of flame of class A category with property of beeing termite / borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast / lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast / lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door / window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 39 | Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panel door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 40 | Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) flush door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 41 | S & F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 2mm including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller 2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner) |
| 42 | S&F 25 mm thick Flush shutters, solid core construction, with block board core with decorative face veneers withlipping on both sides, complete in all respect as specified and directed. |
| 43 | S&F 75 mm size of butt hinges stainless steel, complete in all respect as specified and directed. |
| 44 | S&F 100 mm size of mild steel butt hinges ISI marked, complete in all respect as specified and directed. |
| 45 | S&F aluminium anodised, barrel tower bolt of extruded section 200 mm long, complete in all respect as specified and directed. |
| 46 | S&F Aluminium handle cast type anodised 125 mm, complete in all respect as specified and directed. |
| 47 | S&F Aluminium handle cast type anodised 150 mm size (ISI marked) complete all as specified and directed. |
| 48 | S&F aluminium anodised sliding door bolts with hasp and staple (boilt type) 16 mm dia bolt, 250 mm long, with and including a minium of 6 bolts and nuts four on bolt plate and two on staple plate, complete in all respect as specified and directed |
| 49 | S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed. |
| 50 | S&F PVC coloured insulated over MS pipe 20 mm dia curtain rod with fixing bracket, stops, rollers etc. complete all as specified and directed. |
| 51 | S & F of 1.6mm thk MS plate as in wall clading of steel gates with necessary arrangement and similar work complete all as specified and diretced. |
| 52 | M&L preparation of untreated new steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 53 | M & L for Broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete in all respect as specified and directed |
| 54 | M&L for river bed fine sand filling under floor or below paver blocks incl. watering and consolidation complete in all respect as specified and directed. |
| 55 | Supply and spreading fine river sand in trenches for cushioning of under ground cable/filling cable ducts complete all as specified and as directed by Engr-in-Charge at site. Note : Only punned thickness shall be measured for payment purpose |
| 56 | M&L for cement concrete Type C-2, 1:3:6 (using 40mm nominal size crushed and graded stone aggregate) in foundations filling and mass concrete as in manhole etc. complete in all respect as specified and directed. |
| 57 | M & L 75 mm thick PCC (1:3:6) type C-2 using 40 mm nominal size crushed and graded stone aggregate laid in floor, path etc. or of similar type finished the surface even and fair without using extra cement complete in all respect as specified and directed. |
| 58 | Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed. |
| 59 | Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed. |
| 60 | Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed. |
| 61 | Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in Skriting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed. |
| 62 | M & L 75 mm thick PCC 1:3:6 type C-2 using 40mm graded aggregate as in plinth protection/footpath etc finished the surface even and smooth without using extra cement. |
| 63 | S & F powder coated aluminium three tier window frame including necessary joining cleats, of Jindal section No 20832 or equivalent section of appd make of 1.5mm thick complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner) |
| 64 | S & F powder coated aluminium window and ventilator shutters, side hung type with/without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No) grade), powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner) |
| 65 | S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane, complete in all respect as specified and directed. |
| 66 | S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples fixing withbeads, complete in all respect as specified and directed. |
| 67 | S&F of CP two way bib tap with health faucet 15mm dia fancy type with 1.00 mtr tube and hook (braded tube) complete all as specified and directed |
| 68 | M&L for 110 mm Bore PVC (SWR) pipe single socket in any length with rubber ring joints fixed to wall complete all as specified and directed. |
| 69 | S & F PVC (SWR) pipes single socketed in any length with rubber ring jointslaying in trenches 150 mm bore complete in all respect as specified and directed. |
| 70 | S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 71 | S&F 110mm PVC (SWR) WC connector bent type complete all as specified and directed. |
| 72 | S&F PVC(SWR) junction single (single 'T') equal or unequal 110mm bore complete all as specified and directed. |
| 73 | S & F PVC (SWR) 110 mm dia vent cowl complete all as specified and directed. |
| 74 | S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75 mm bore complete in all respect as specified and directed. |
| 75 | S&F PVC (SWR) 75mm dia bent type complete all as specified and directed. |
| 76 | S & F PVC (SWR) branch piece with access door, single (Single Tee) equal or unequal 75mm bore pipe complete in all respect as specified and directed. |
| 77 | S & F CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall of size 20mm outer dia complete all as specified and directed. |
| 78 | S & F CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall of size 25mm outer dia complete all as specified and directed. |
| 79 | S & F 4.00 mm thick of 600 mm x 450 mm size bevelled edge mirror of selected quality decorative type mounted on 6 mm commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 80 | S&F in repair wash hand basins (WHB), vitreous china of size 550x400 mm (flat back or angle back type) with pedastal stand, including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32 mm dia bore waste fittings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15 mm bore dia fancy type CP finish pillar tap, cast copper alloy with capstand heads, screw down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screw for iron pipes complete in all respect as specified and directed. |
| 81 | S&F in repairs vitreous china urinal flat back large of size 37.5X39X59cm white, including waste coupling, urinal spreader fixing arrangement to walls, PVC waste pipe etc. complete in all respect as specified and directed. Make: Hindware Cat No. 60002 (urinal), or equivalent make of Cera, Perryware |
| 82 | S&F Vitreous China urinals, full stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed. |
| 83 | S & F PVC valveless, syphonic action type, low level, dual flush cistern, white, with inlet ball valve, float and handle including brackets & flush pipe of polyethylene complete all as specified and directed. |
| 84 | S&F 15mm bore dia CP finish , bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/CPVC pipe/fittings or for brass ferrule including cup washer/flange complete all as specified and directed. |
| 85 | S & F 15mm bore dia CP finish,angle valve, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/CPVC pipe/fittings or for brass ferrule including cup washer/flange complete all as specified and directed. |
| 86 | S & F vitreous china wash down water closet Pan (pedestal pattern) white including plastic water closet seat cover, white, closed pattern with flat bottom, and mild steel chromium plated hinging device (exclusive flushing cistern and flush pipe) complete all as specified and directed. |
| 87 | S&F in vitreous chinaware sqatting pan of size 580 x 440 mm, 'ORISSA PATTERN' with new PVC 'P' or 'S' trap bedded in cement concrete (excluding flushing cistern and flush pipe) with integral foot rests, complete in all respect as specified and directed. |
| 88 | S&F chrome finished toilet paper holder of cast copper alloy complete all as specified and directed. |
| 89 | S & F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete in all respect as specified and directed. |
| 90 | S & F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement floor trap complete all as specified and directed. |
| 91 | S & F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; and similar work conforming to Fe. 290, Gde-E-165 complete in all respect as specifified and directed. |
| 92 | M & L for waterproof cement based putty @ 1 Kg (undiluted) per sq mtr of average thickness 1mm over the newly plastered surfaces of wall to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanicsm) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface free from dust etc by skilled labour as per following steps : -Step 1 : Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 Kg putty per minute.Step 2 : Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a max pressure 3300 PSIStep 3 : Allow 6-8 hrs time to dry the putty surfaceNote : (a) The work pertaining to periodical services and water proofing shall be executed as per manufacturer instructions i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by Engr-in-Charge.(b) Cost of Scafolding upto 10 mtr height of building is included in this item.(c) Masking of waindow/doors during spray painting using polythine film will be included (d) Cleaning and clearing site of paint, mats etc included. |
| 93 | M & L for two coat water based premium acrylic smooth exterior emulsion of approved colour with silicon additive and color stay Techonology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/litre as per the LEEDS specifieecations, Anti Algal properties in two coats @ 1.79 ltr (Undiluted)/10 Sqm with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow spreed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface in both coats of paint complete all as specified and directed.Note : (a) The work pertaining to periodical services and water proofing shall be executed as per manufacturer instructions i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by Engr-in-Charge.(b) Cost of Scafolding upto 10 mtr height of building is included in this item. |
| 94 | S & F of polythene film black 150micron complete all as specified and directed by Engineer in charge |
| 95 | M & L for applying Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, at the junction of Perimeter of the building and every 3 mtr in the lateral dimension all as specified and directed. |
| 96 | S&F 20mm dia of gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron/CPVC pipe/fittings and fixed complete all as specified and directed. |
| 97 | S & F Rotational moulded polyethylene water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including two tank nipples one at inlet and other at one outlet of 20mm dia complete all as specified and directed. |
| 98 | S & F PTMT ball valve high pressure 20mm bore with epoxy coated aluminium rod & high density plastic ball screwed for iron/CPVC pipe/fittings complete all as specified and directed. |
| 99 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 100 | M&L Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in Type A-1 1:1.5:3 cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8m dia and 3.0m depth complete all as specified and directed. |
| 101 | M & L for 150mm bore pipe for concrete bed in PCC 1:4:8 type D 2 using 40mm nominal size crushed and graded stone aggregate to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested in complete in all respect as specified and directed. Please Enable Macros to View BoQ information |
| 102 | M & L for 150mm bore pipe for concrete bed in PCC 1:4:8 type D 2 using 40mm nominal size crushed and graded stone aggregate to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested in complete in all respect as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysSep 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender