Tender For Electrification Work For Bus Stand At Truck Terminus, Paribahan Nagar, Matigara, Dist. Darjeeling
Tender Value
24.43 Lakhs
Estimated cost
Bid Submission
03 Sep 2026
10 days left
EMD
48879
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Darjeeling → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Electrification Work For Bus Stand At Truck Terminus, Paribahan Nagar, Matigara, Dist. Darjeeling
BOQ
| Sl. No. | Item Description |
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 2 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived fromnatural sources : 6 graded stone aggregate 20 mm nominalsize derived from natural sources) |
| 3 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 4 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal dia Pipes |
| 5 | Direction and Place Identification Signs with size more than 0.9 sqm size Board. Providing and erecting direction and place identification retroreflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos.firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801). |
| 6 | Supplying and fixing of 26300lm + 5% LED flood light fitting with secondary optics with lens made in pressure die cast housing with heat sink & aluminium extrusion and front glass IP66 protection with Silicon gel Potted Driver, Road Way Luminarie with BIS 'R' Mark along with 5 KV inbuilt surge Protection. CHIP Make : CREE / NICHIA / LUMILEDS / OSRAM / SEOUL. (Make: PHILLIPS. Cat no. : BVP483 LED263 CW SWB PSU GR SPD or Equivalent model of Surya / Bajaj /Panasonic / Crompton ), conforming to Technical Specification and latest accreditation. LM-79 and LM-80 report to be provided conforming to latest NABL accreditation. LED should be warranty for 3 years including dismantling the old damaged fittings & suppying, laying 0.85 mtr. 1.1 KV grade 3 core 1.5 Sq. mm PVC insulated FR PVC sheathed multistranded cable for connection etc as required. |
| 7 | Dismantling and refixing of defective 30m high mast along with double drum winch, with all accessories from its position by using Crabe/ Hydra van. |
| 8 | Supplying and Fixing of self sustaining Double Drum Winch, Power Tool and Pully Arrangement having following specification :- Capacity: 750 Kg, Reduction Ratio: 53:1 pully Arrangement for Steel Rope: 3 Sets, Pully Arrangement for Electric Cable: 1 Set |
| 9 | Supplying and Fixing 2.0 HP Three Phase Induction Motor, Single Speed with reversible of speed : 1400 RPM |
| 10 | Supplying and Fixing Non Corrodible Stainless Steel of 6mm dia Marine Grade of 7/19 construction of AISI Grade: 316 grade with thimble arrangement, buffer arrangement, compensating disc, safety disc, safety lock as required. |
| 11 | Supplying and Fixing of Trailing Cable of 6 core 2.5 sqmm from top junction box to bottom panel box as required. |
| 12 | Supply & Fixing of twin dome aviation obstruction lights of Min 2 X 100W GLS Lamp / 2 X 40W LED / 1 X Neon Spiral with neon spiral lamp. Make: Philips / Bajaj / Crompton / Havells. |
| 13 | Supplying and fixing of 70 W + 5% LED Street light with pressure die cast housing, high performance polycarbonate modular secondary lens optics with IP66 ingress protection. 4KV inbuilt and 10 KV external surge protection with Top opening driver cover for easy maintenance. efficacy - 110lm with Three years (03) warranty. (Make - Bajaj Cat No. ENXT P 84L WH PO PC SD MT or equivalent make of Phillips / Surya/ Crompton ) |
| 14 | Lowering & lifting the head carriage frame manualy etc. as required |
| 15 | Supply of control panel housing 32 A TPN MCB incomer, double dial timer, contactor, circuit for the automatic switching control of luminaries, outgoing terminals and control circuit for the power tool motor, 2 Nos 9A Contactors and raise lower push button all complete. |
| 16 | Supply, fixing, testing & commissioning wall/floor mounted (0.5 X 0.6 X 0.3) LT panel primer coated with powder coated paint &provided with required gasket for dust/vermin proof with degree of protection IP42 suitable for 415Volt 3phase, 50 Hz, 4 wire system fabricated out of CRCA sheet up to 2 mm thick (1.6mm for doors) duly compartmentalized for incomer, bus section, outgoings, cable alleys & CT, PT Ampere , Volt , selector switches, frequency , phase indicating lamp, Energy complete including cost of busbar supports, detachable cable gland plates,2 earthing terminals, internal wiring &fixing of separately supplied MCBs, MCCBs, ACB, panel mounted changeover switch/SFUs, etc. as required but excluding cost of busbar strips, Ampere , Volt , selector switch as per approved design & specification |
| 17 | Erection of feeder pillar with CC Foundation with 1:3:6 and neatly plastered with neat finish etc. as required. |
| 18 | Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI-Medium GI pipe. |
| 19 | Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe |
| 20 | Extra for treatment of soil by using salt & charcoal or coke for plate electrode |
| 21 | Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required |
| 22 | Supply of 1.1 KV grade XLPE insulated PVC Sheathed Aluminum conductor armoured Cable 2 core 10 Sq.mm (Conforming to IS - 7098 (Part 1) : 1988) Make: Incab / CCl / Gloster / Crystal / Polycab / Havells/ KEI/ RR Cable |
| 23 | Supply of 1.1 KV grade XLPE insulated PVC Sheathed Aluminum conductor armoured Cable 4 core 16 Sq.mm (Conforming to IS - 7098 (Part 1) : 1988) Make: Incab / CCl / Gloster / Crystal / Polycab / Havells/ KEI/ RR Cable |
| 24 | Laying of one cable upto 50 Sq.mm through existing RCC / Hume / GI pipe / HDPE Pipe open masonary trench for single 2, 3.5 & 4 core. |
| 25 | Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required. f) 80mm |
| 26 | Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials : For 2 core 10 Sq.mm . |
| 27 | Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials : For 4 core 16 Sq.mm . |
| 28 | Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC Armoured cables as below. For 4 core upto 10 sqmm |
| 29 | Painting of Steel Tubular Pole of lengths and no. of coats of paint, as given below with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint.above 9.0 mtr. long pole : 1st coat of aluminium paint over 1 coat of RO priming. |
| 30 | 2nd coat of aluminium paint over 1st coat |
| 31 | Providing CC (6:3:1) muffing 450x450x600 mm in size or equivalent size of cylindrical muffing above ground level around the pole base complete with 3 mm thick neatly finished cement plaster all round after dismantling the unserviceable muffing if any incl. fixing only loop box if necessary a) Without Loop Box |
| 32 | Supply of Pole Mount waterproof PVC Square Junction Box with IP-67 protected for Accessories having dimension 350 x 250 x 138 minimum. Make: Sintex |
| 33 | Painting Block Letters or Digits within a circle/square as required, with ”Black Japan” paint of approved make & brand, the size of letters and digits as given below : Size 125 mm and upto 150 mm |
| 34 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythene pipe complete with all accessories embedded in wall to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC (i) Average run 6m. |
| 35 | Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required |
| 36 | Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. 2+4 Way make:ABB |
| 37 | Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection. Make: Legrand, 32A |
| 38 | Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection. Make: L&T, 6 - 32A |
| 39 | Supply and fixing of EnduraLED Bulkhead Pressure Die cast housing LED bulkhead with IP66 Protection and IK09 impact resistance suitable for surface and wall mounting applications on ceiling fifling on wall /ceiling by screws etc.Make ; Philips, 6 wafl NW |
| 40 | Supplying & Fixing angular batten holder (Anchor) on 75mm dia PVC round block / round bakelite on wall/ceiling. |
| 41 | Supplying of Ventilus 6“ 150 Ivory, White, make : crompton make plastic ventilating exhaust fan AC 230-250. |
| 42 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythene pipe complete with all accessories embedded in wall to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC. (i) Average run 6m. |
| 43 | Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required b)3 x 22/0.3 (1.5 sqmm) |
| 44 | Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection. Make: Legrand, 32A |
| 45 | Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection. Make: L&T, 6 - 32A |
| 46 | Supply & Fixing 240 V 6 A Modular type switch (Brand approved by EIC) on existing GI Modular type switch board having top cover plate and making necessary connections as required |
| 47 | Supply & Fixing 240 V, 6A, 5 pin Modular type plug socket (Brand approved by EIC), without switch & plug top, on existing GI Modular type switch board with top cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 48 | Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Brand approved by EIC) with 16A Modular type switch, without plug top on 4 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 49 | Supplying of approved make 450mm sweep wall fan oscillating type with base, blades, guard, speed regulator etc. AC 230- 250 volts. |
| 50 | Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length |
| 51 | Supply TMC501 Conventional industrial baflen Philips LED tube, model no : TMC 501 P 1xT-LED 22W P3241 with 1no Mas LED tube 1200mm 18W865 T8 I - 2100lm including necessary connection. |
| 52 | Fixing only single /twin fluorescent light fitting complete with all accessories directly on wall/ceiling/HW round block and suitablesize of MS fastener |
| 53 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythene pipe complete with all accessories embedded in wall to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC (i) Average run 6m. |
| 54 | Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required b)3 x 22/0.3 (1.5 sqmm) |
| 55 | Supply TMC501 Conventional industrial baflen Philips LED tube, model no : TMC 501 P 1xT-LED 22W P3241 with 1no Mas LEDtube 1200mm 18W865 T8 I - 2100lm including necessary connection. |
| 56 | Add GST Factor @0.973 and Cost index Factor @1.21 on Sl. No. 1 to 4 |
| 57 | Add 18 % GST on Sl No. 5 |
| 58 | Add 18 % GST on Sl No. 6 to 55 |
| 59 | Add 1 % Cess on Sl. No. 6 to 55 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender