Tender For Provn Of Soak Pit Near T-10 Bldg; special Repair To Bldg No T-132 Or Guest Room; special Repair To Bldg No T-34 (Offr Gym Hall); special Repair To Bldg No T-237 And T-239 At Along Mil Stn Under Ge 872 Ews
Tender Value
42.09 Lakhs
Estimated cost
Bid Submission
09 Sep 2026
16 days left
EMD
84200
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
West Siang → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Soak Pit Near T-10 Bldg; special Repair To Bldg No T-132 Or Guest Room; special Repair To Bldg No T-34 (Offr Gym Hall); special Repair To Bldg No T-237 And T-239 At Along Mil Stn Under Ge 872 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish complete all as specified and directed. |
| 2 | Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance complete all as directed by the Engr-in-Charge |
| 3 | Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed |
| 4 | Dismantling Timber Scantlings, 40 Sqcm and over in Section, in any Position, in Unframed Work, complete all as specified and as directed. |
| 5 | Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. |
| 6 | Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed. |
| 7 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing rubbish complete all as specified and directed |
| 8 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed. |
| 9 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 10 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets/ snap grid frame etc complete all as specified and directed. |
| 11 | Taking up or down 15 mm bore, Steel tubing and connections in any position ,complete all as specified & directed. |
| 12 | Taking up or down 20 mm bore, Steel tubing and connectionsin any position ,complete all as specified & directed. as directed. |
| 13 | Taking down eaves gutters and rainwater/soil/waste pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed |
| 14 | Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 15 | Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, cable etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 16 | Excavating over areas, n exc 1.5 m deep and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 17 | Excavating over areas, exc 1.5 m deep but n exc. 3.00 and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 18 | Excavating over areas, exc 3.0 m deep but n exc. 4.50 and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 19 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed. |
| 20 | Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 21 | M & L for broken brick , Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified & directed. |
| 22 | M & L for Sand cushioning to under ground cable in trenches /existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and streching the cable complete all as specified and directed. |
| 23 | M & L for Pre-cast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), block masonry with solid blocks of size 300x200x200mm or 300x200x100mm, having compressive strength of not less than 100 Kg/Sq Cm (As per IS-2185) exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed. |
| 24 | M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed. |
| 25 | M&L Plain Cement Concrete type C2 (1:3:6), using 40mm graded crushed stone aggregate as in foundation of man holes complete all as specified and as directed. |
| 26 | M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed. |
| 27 | M & L for precast cement concrete (1:2:4) type B1 (using 12.5mm graded stone aggregate) setting in CM 1:6 work for in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces |
| 28 | M&L for Plain cement concrete 1:2:4, type B-1, (using 20 mm graded stone aggregate) as in benching, coping and brick steps including necessary form work complete all as specified and directed. |
| 29 | M&L Reinforced cement concrete type B-0 (1:2:4) (Using 12.50mm graded crushed stone aggregate) as in Roof Beams, Cantilevers, Bres-summers, Lintels over 1.50 Metre Span etc complete all as specified and directed.NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items. |
| 30 | Material and Labour RCC (Nominal mix) 1:2:4 (Type B1, Using 20 mm graded crushed stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 31 | M & L Reinforced Cement Concrete 1:2:4, Type B-1 (Nominal Mix) (using 20 mm graded stone aggregate) for columns ,pillars ,Piers ,posts and struts complete all as specified and directed.(Note : Reinforcement will be measured & paid seperately) |
| 32 | M & L Reinforced Cement Concrete 1:2:4, Type B-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed.(Note : Reinforcement will be measured & paid seperately) |
| 33 | M&L Use and waste for Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed. |
| 34 | M&L Use and waste of Formwork to sides of Pillars, Posts, Struts, Piers, Columns and stanchions, flat, rough finished surfaces of concrete, ( complete all as specified and as directed. |
| 35 | M&L Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified & directed |
| 36 | M&L 6mm thick Plywood, grade BWP, type BB fixed with screws to timber frame wok as in repair complete all as specified and as directed. |
| 37 | S&F powder coating (minimum thickness of powder coating 50 micron)aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed. |
| 38 | S&F Powder coated aluminium door shutter, aluminium section weighing 0.55 Kg/m (minimum) thickness not less that 2.00mm including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos. in each door shutter, floor hinges, powder coated aluminium snap beading, screw etc complete all as specified and directed. |
| 39 | S&F aluminium door shutter, aluminium section weighing 0.55 Kg/m (minimum) thickness not less that 2.00mm including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos. in each door shutter, floor hinges, powder coated aluminium snap beading, screw etc complete all as specified and directed. |
| 40 | S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed. |
| 41 | S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 42 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed. |
| 43 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 44 | S&F Steel window with side hung shutter including projection type hinges with steel handles, and steel peg stay with glazing bars dovetailed or welded complete all as specified. |
| 45 | S&F Steel window with side hung shutter including projection type hinges with steel handles, and steel peg stay without glazing bars dovetailed or welded complete all as specified. |
| 46 | S&F Aluminium body(extruded section) door closer hydraulically regulated, designation No 3, universal type suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg and fixed as in repair complete all as specified and as directed. |
| 47 | S & F 100 mm long, stainless steel butt hinges fixed with stainless steel hinge pin etc complete all as specified and directed. |
| 48 | S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 49 | S & F 125 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 50 | S & F 150 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 51 | S & F 125 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 52 | S&F Mortice lock, Brass, 4 Levers, vertical type, size 100 mm and fixed, complete all as specified and as directed. |
| 53 | S&F Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring (overall length of cover plate 150mm) complete all as specified and as directed. |
| 54 | S & F 300 mm Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt complete all as specified and directed. |
| 55 | S&F 20mm dia brass chromium plated tubular curtain rod with brackets on both side, stops, rollers etc complete all as specified and as directed. |
| 56 | S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 57 | S & F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 58 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 59 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 60 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysSep 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender