Tender For Certain Repairs To Fencing Gates, Boundary Wall, Traverse Wall, Hard Standing, Drain Path And Connected Miscellaneous Works Incl E/M Installation At 223 Abod Mil Stn Suranussi Under Age (I) Suranussi
Tender Value
35 Lakhs
Estimated cost
Bid Submission
08 Sep 2026
19 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalandhar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Repairs To Fencing Gates, Boundary Wall, Traverse Wall, Hard Standing, Drain Path And Connected Miscellaneous Works Incl E/M Installation At 223 Abod Mil Stn Suranussi Under Age (I) Suranussi
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work built in cement mortar including all quoins, arches, pillars etc but including ashlar facings dressed stone work and pre cast concrete articles complete all as specified and as directed by the Engineer-in-Charge. |
| 2 | Demolition of cement conc in ground floor and pavings not exceeding 15 cm thick above or below ground level. |
| 3 | Material and labour for brick work built in cement mortar (1: 6) with sub class ‘B’ bricks, straight or curved on plan exc 6 m mean radius, using old size bricks complete all as specified and as directed by the Engineer-in-Charge. |
| 4 | -ditto- as per item no 03 above except Brick complete all as specified and as directed by the Engineer-in-Charge. |
| 5 | M&L for brick work sub class 'B' bricks laid flat bedded and jointed in CM (1:6) and pointed in CM (1:3) complete all as specified and as directed by the Engineer-in-Charge. |
| 6 | -ditto- but laid on edges complete all as specified and as directed by the Engineer-in-Charge. |
| 7 | Taking down cement plaster of any description on brick or stone wall as in boundary wall etc, including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified & directed by the Engineer in Charge. |
| 8 | Material and labour for rendering 15 mm thick cement plaster in cement mortar (1:4) of brick / concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Material and labour for preparation of new surfaces of walls including cornices, pilasters etc (Plastered or un plastered surfaces) and applying two of coats of cement base paint over a coat of alkali primer complete all as specified & directed by the Engineer in Charge. |
| 10 | Material and labour for plain cement concrete (1:3:6), type C-2 using 40mm graded crushed stone aggregate, as in surface channel complete all as specified and directed by the Engineer-in-Charge. |
| 11 | M&L 25 mm thick Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in–Charge. |
| 12 | Demolition of Stone slabs and tiles laid,bedded and printed in any mortar of any description or thickness in floors, aprons etc |
| 13 | M & L Machine pressed precast conc. interlocking paver block cosmic paver vlock (rectangulat/star etc.) (Red/yellow)any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade with grey cement and with pigment complete all as specified and directed by Engr - in - Charge. |
| 14 | ditto- all as per items no above 13 except tile complete all as per directed by engr-in- charge |
| 15 | M & L Machine pressed precast conc. interlocking paver block /cosmic paver block any shape (rectangulat/star with PU coating etc.) (Red/yellow)any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and with pigment complete all as specified and directed by Engr - in - Charge. |
| 16 | Providing and laying precast cement concrete at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening with PVC Pipe wherever required and apply two coats of plastic emulsion paint over a priming paint plaster coat complete all as specified and directed by Engineer -in charge. |
| 17 | M&L for preparation of concrete surfaces of any description over 10 cm girth or width, cornices etc booming down with steel wire brushing and applying two coat of synthetic enamel paint complete all as specified and directed. |
| 18 | M & L Cement concrete 1:2:4 type B–1 using 20mm graded stone aggregates in copings,, including weathering, slightly rounded or chamfered angles and throating, as directed all as specified and directed by Engineer - in - Charge . |
| 19 | M & L for chequered cement concrete tiles 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry and pigments as in floors including 20 mm thick screed or bedding layer in CM 1:6 all as specified and directed by Engineer-in Charge |
| 20 | M&L providing precast cement concrete louvres and jallies, with RCC post 50 mm thick (measured solid), type B-0(1:2:4) using 12.5mm graded aggregate including all mould- ings but excluding frame set in cement mortar 1:4 complete all as specified and directed by Engr-In-Charge |
| 21 | M&L Granite (of any type) work (table rubbed and polished) 20 mm thick in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed or bedding layer in CM 1:6 all as specified and directed by Engineer-in Charge |
| 22 | Supply and fix in repairs galvanised 2 strand steel barbed wire 2.24 mm dia , barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire, staple or steel pins etc complete all as specified and directed by Engr-in-Charge. (Each line wire to be measured) |
| 23 | All as per Item No 22 above here-in-before but restraining re-securing including making good staples etc. complete all as specified and directed by Engr-in-Charge. (Each line wire to be measured) |
| 24 | Material and labour for mild steel round bars 10mm dia Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde -E-165) as in reinforcement cut to length, bent to shape including cranking bending, and binding with MS wire (annealed) not less than 0.9 mm dia complete all as specified and as directed by Engineer-in-charge. |
| 25 | Dismantling fencing wire mesh, any type complete all as specified and as directed by the Engineer-in-Charge. |
| 26 | Fixing of chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by Engr-in-charge |
| 27 | Supply only Chain link fencing made out of plain mild steel galvinised wire , width of aperature 100 mm x 100 mm x 4mm dia to new steel posts by means of nuts and bolts, complete all as specified and directed by Engineer - in – Charge |
| 28 | Dismantling posts or struts embedded (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground |
| 29 | S&F for Mild steel angle iron fencing post and struts in fencing incl necessary cutting drilling welding etc and bending to swan neck shape as required and drilling holes notching for wives etc conforming to Fe-290 Gde E-165 complete all as specified. |
| 30 | M&L Plain Cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in Charge. |
| 31 | S&F mild steel screw bolts 12mm dia(machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but n. exc. 15 cm long and dia of shank 5 to 10 mm complete all as specified and directed. |
| 32 | M&L applying two coats of synthetic enamel paint over a coat of red oxide 0r zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed. |
| 33 | M&L for preparation of new steel surfaces n exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specifed and directed. |
| 34 | M&L for PCC type D2 1:4:8 using 40 mm graded aggregate as in foundations, filling and mass concrete all as specified and directed |
| 35 | Dismantling wooden boarding, any description, fixed in any position with nails complete all as specified and directed by Engineer-in Charge. |
| 36 | Supply and fixing informatory Sign board of size 1200 mm x 900 mm made of aluminium sheet 2 mm thick with stainless steel rectangular frame using 25 x 15 mm rectangular pipe with 35 mm dia stainless pipe in outer border all around retro reflective high intensity 400 micron thick blue/yellow colour sheet pasted with heating process on both bsides of the board including 75 mm to 100 mm high black colour letters cut to shape with special plotter and in proper manner incidating Shed No as directed by Engr in charge .02 Nos 75 mm dia stainless steel pipes of 304 grade glossy finish with MS plate 3 mm thick welded at bottom of pipes shall be provided the board shall be fixed at height of 3.0 mm (top level of board) above GL and shall be embedded in ground using PCC 1:2:4 type B-1 of min size 300mmx300mmx600mm including necessary from work.excavartion and earthbwrk complete all as specified and directed. |
| 37 | Supply and fixing informatory Sign board of area exc 3 sqm n.exc 4.50 sqm both side measured made of aluminium sheet 2 mm thick with stainless steel rectangular frame using 25 x 15 mm rectangular pipe with 35 mm dia stainless pipe in outer border all around retro reflective high intensity 400 micron thick blue/yellow colour sheet pasted with heating process on both bsides of the board including 75 mm to 100 mm high black colour letters cut to shape with special plotter and in proper manner incidating Shed No as directed by Engr in charge .02 Nos 75 mm dia stainless steel pipes of 304 grade glossy finish with MS plate 3 mm thick welded at bottom of pipes shall be provided the board shall be fixed at height of 5.0 m (top level of board) above GL and shall be embedded in ground using PCC 1:2:4 type B-1 of min size 450mmx450mmx750mm including necessary from work.excavartion and earthbwrk complete all as specified and directed. |
| 38 | Removing/excavating mud/silt/vegetation inside in the drain (open/closed) of any description and removing excavated material exc 500m & n exc 1km deposited where directed at a level n exc. 1.5m above the starting point, and cleaning top, sides of drain up to 0.60m both sides complete and all as specified and as directed. |
| 39 | Removing/excavating mud/silt/vegetation settled inside the culvert (pipe/box) of any description and removing excavated material exc 500m & n exc 1km deposited where directed at a level n exc. 1.5m above the starting point, and cleaning top, sides of drain up to 0.60m both sides complete and all as specified and as directed. |
| 40 | Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 41 | Material & Labour for providing and fixing stainless steel (Grade 304) gate, made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified & directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysSep 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender