Tender For special Repair To Bldg No P-3/71 & P-3/45A (Office Complex) Of Sho (L) At Military Station Jammu Under Ge Satwari.
Tender Value
47.46 Lakhs
Estimated cost
Bid Submission
08 Sep 2026
14 days left
EMD
94920
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No P-3/71 & P-3/45A (Office Complex) Of Sho (L) At Military Station Jammu Under Ge Satwari.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. |
| 3 | Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed. |
| 4 | Dismantling floor, hearth or wall tiling/ terrazzo dado from wall surface including cement mortar bedding, (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed. |
| 5 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed |
| 6 | Demolition of cement concrete (un-reinforced) in ground floor and pavings n. exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site to out side defence premises complete all as specified and directed |
| 7 | Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removing unserviceable material from work site to outside defence premises complete all as specified and directed |
| 8 | Demolition of reinforced cement concrete of any description & in any position not otherwise described and removing the rubbish from the work site to outside defence premises complete all as specified and directed. |
| 9 | M&L for 25 mm thick plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed. |
| 10 | M&L for 40 mm thick plain cement concrete 1:2:4 ,type B-1 (using 20 mm graded crushed stone aggregates) as in floor finishes in panels of 600x600mm by providing 5mm thick aluminium dividing strips, finished even and smooth without using extra cement complete all as specified and directed. |
| 11 | M&L for 7 to 8mm thick non skid coloured digital ceramic tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:6 complete all as specified and directed. |
| 12 | M&L for 8 to 9 mm thick vitrified ceramic double charged, edge cut, joint free, coloured or printed any shade tiles (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.72 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Note:- The tiles to be laid with 5mm thick HDPE tile spacers (horizontal as well as vertical) and gap to be grouted with epoxy upto the depth of tile. |
| 13 | M&L for 8 to 9 mm thick vitrified ceramic double charged, edge cut, joint free, coloured or printed any shade tiles (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.72 sqm , as in vertical surfaces such as skirting / dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. Note:- The tiles to be laid with 5mm thick HDPE tile spacers (horizontal as well vertical) and gap to be grouted with epoxy upto the depth of tile. |
| 14 | M&L for glazed ceramic coloured digital tiles,300x600x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 15 | M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing at edges complete all as specified and directed. |
| 16 | M&L for post anti termite treatment by treating the top surface of filled earth and plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed . |
| 17 | S&F Machine cut kota stone slab in flooring 18-20mm thick and of size exc 0.16 sqm, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,cutting and mirror polishing over and including 20 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. |
| 18 | S&F Machine cut kota stone slab,18-20mm thick in vertical surfaces such as skirting in full length in single piece without joint with groove cutting in double line of stair width,dado,risers etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,cutting and mirror polishing with full round bull nosing at edges of treads and risers over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 19 | M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete as directed, edge joint filling with cement mortar 1:4 complete including necessary excavation complete all as specified and directed |
| 20 | M&L for plain cement concrete 1:2:4 ,type B1(using 20mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed. |
| 21 | M&L for 75mm thick PCC 1:3:6 , type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:20 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed . |
| 22 | M&L for reinforced cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed . |
| 23 | M&L for reinforced cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregates) as in beams, cantilevers, chajjas,bressummers, lintels and the like; complete all as specified and directed . |
| 24 | M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed. |
| 25 | M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc, for rough finished surfaces of concrete complete all as specified and directed. |
| 26 | M&L for use and waste of formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs, n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n. exc 20cm wide fair finished surface complete all as specified and directed . |
| 27 | M&L for Mild steel TMT bars 6mm to 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.. |
| 28 | M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 29 | M&L for brick work with fly ash bricks using old size bricks, straight or curved on plan exceeding exc 6 metre mean radius, built in cement mortar 1:6 complete all as specified and directed . |
| 30 | M&L for brick work with fly ash bricks using old size sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed . |
| 31 | M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface, surface finished even and smooth without using extra cement complete all as specified and as directed. |
| 32 | M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed. |
| 33 | M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed. |
| 34 | M&L for capillary rise treatment of walls with following specification:-Base coat: Berger HS Latex plus or equivalent in make specified in PSConsumption base coat: 0.3 kg/m2Second and Third coat: Latex sheild 2K or equivalent in make specified in PSConsumption top coat: 3 kg/m2System requirements: density: 2.00 kg/ltrcompressive strength: 0.5 N/mm2. |
| 35 | Complete removal of existing water proofing treatment of any description including under layer, taking down cement plaster,concrete & mud pushka of any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust complete all as specified and directed. |
| 36 | M&L for cleaning of the exposed concrete slab & like and repairing the surface irregularities like cracks, potholes with HS Latex Plus(or equivalent) & cement in mixing ratio of 1:4 as per manufacturers method statement by Berger HS Rapairo (or equivalent) i complete all as specified and directed . |
| 37 | M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in padding over roof finished & laid to required slope, mud stops,roof kerbs complete all as specified and directed . |
| 38 | M&L for HomeSheild PU Roofkoat(or equivalent) is a one component liquid ,solvent free , cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years warranty .ASTM D 6083-97 a Waterproofing and heat reflecting system having following key performance properties:-a) UV resistant ,prevent yellowing and weatheringb) Highly elastic upto 350% and crack bridgingc) Excellent adhesion on porous and non-porous substratesd) Tensile Strength >10 N/mm2 with GeoTextile fleecee) Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent)Coverage: 0.2kg/sqm(with 50% dilution of water)Reinforcement: Geotextile 40 gsmSecond coat:Home sheildroofkoat(or equivalent)Consumption: 0.5 kg/sqm.Third coat: HS PU roofkoat(or equivalent)Consumption : 0.8 kg/sqm.System buildup-1.5kg/sqm with geotextile of 40gsm |
| 39 | S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing or composite panel LDPE core PET coating ( both side decorative type ) fixed with and including 5.50mm thick black film glass fixed with rubber gasket with aluminium heading, clips, frame made with aluminium box section as appended below complete all as specified and directed :-(a) Frame 100x44x1.48mm thick with rawl plug(b) Middle and lock rail : 150x44x1.48mm thick(c) Bottom rail : 150x44x1.48mm thick(d) Top rail/style : 85x44x1.48mm thick(e) Aluminium beading : 0.7mm thick(g) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long, brass mortise lock 100mm 4 leaver, aluminium stopper 100 mm long, Including Heavy duty hydraulic door stopper.(h) 04X stainless steel Hinges 100mm long (02x top,01x centre and 01x bottom) on each shutter (j) Making good the wall surface to match with existing finishes complete. |
| 40 | S&F aluminium alloy powder coated aluminium door frame fixed with inside glazing and outside stainless steel wire mesh ,side hung shutters fixed with rubber gasket and aluminium beading, clips, frame made with aluminium box section as appended below complete all as specified and directed :-(a) Frame 100x44x1.48mm thick with rawl plug(b) Middle and lock rail : 150x44x1.48mm thick(c) Bottom rail : 150x44x1.48mm thick(d) Top rail/style : 85x44x1.48mm thick(e) Aluminium beading : 0.7mm thick(f) Plain glass 5.5mm thick with black film(g) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average with of aperture 1.40 mm and fixed with stainless steel wire staples(h) 04X stainless steel Hinges 100mm long (02x top,01x centre and 01x bottom) on each shutter (j) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long, brass mortise lock 100mm 4 leaver ,aluminium stopper 100mm long, Including Heavy duty Hydroulic door stopper.(k) Making good the wall surface to match with existing finishes complete. Please Enable Macros to View BoQ information |
| 41 | S&F aluminium alloy powder coated aluminium door frame fixed with inside glazing and outside stainless steel wire mesh ,side hung shutters fixed with rubber gasket and aluminium beading, clips, frame made with aluminium box section as appended below complete all as specified and directed :-(a) Frame 100x44x1.48mm thick with rawl plug(b) Middle and lock rail : 150x44x1.48mm thick(c) Bottom rail : 150x44x1.48mm thick(d) Top rail/style : 85x44x1.48mm thick(e) Aluminium beading : 0.7mm thick(f) Plain glass 5.5mm thick with black film(g) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average with of aperture 1.40 mm and fixed with stainless steel wire staples(h) 04X stainless steel Hinges 100mm long (02x top,01x centre and 01x bottom) on each shutter (j) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long, brass mortise lock 100mm 4 leaver ,aluminium stopper 100mm long, Including Heavy duty Hydroulic door stopper.(k) Making good the wall surface to match with existing finishes complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysSep 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender