Tender For Repair To Joinery Work And Other Misc Work At Mil Stn Katihar Under Age (I) Katihar.
Tender Value
9.99 Lakhs
Estimated cost
Bid Submission
08 Sep 2026
15 days left
EMD
19980
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Katihar → Bihar
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Joinery Work And Other Misc Work At Mil Stn Katihar Under Age (I) Katihar.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutter (without taking off shutters from the frame) incl dismantling of PCC bed blocks for hold fasts complete all as specified and as directed by Engr-in-charge |
| 2 | Taking down chowkats or frames exc 1.5sqm and not exc 4.0 sqm each with shutters ( without taking off shutters from the frame ) .complete all as specified and as directed by Engr-in-charge |
| 3 | S&F PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with mild steel square tubes in opening as per specific drawing. complete all as specified and as directed by Engr-in-charge |
| 4 | S&F factory made solid panel PVC door shutter 30mm thick consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour pvc 'C' channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,Panelling of plain colour pvc sheet to be fitted in the ms frame complete all as specified and as directed by Engr-in-charge |
| 5 | S&F 100mm size type B-21 Butt hinges extruded aluminium alloy with galvanised MS sheet hinges pin anodised complete all as specified and as directed by Engr-in-charge |
| 6 | S&F Aluminium anodised barrel tower bolts of extruded section 150 mm long and fixed with screws complete all as specified and as directed by Engr-in-charge |
| 7 | S&F extruded aluminium alloy handels fabricated type, anodised, 150mm long complete all as specified and as directed by Engr-in-charge |
| 8 | S&F Aluminium anodised sliding door bolts of size 300mm long, with hasp & staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extreded sections or cast aluminium alloy complete all as specified and as directed by Engr-in-charge |
| 9 | S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length cover plate 150mm complete all as specified and as directed by Engr-in-charge |
| 10 | Supply and fixing galvanized MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and as directed by Engr-in-charge |
| 11 | Supply and fixing galvanized MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed as in repairs complete all as specified and as directed by Engr-in-charge |
| 12 | Hacking out old unserviceable glass panes from metal framing including punching drilling out old unserviceable glazing pins complete all as specified and as directed by Engr-in-charge |
| 13 | Supply and fixing 3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and as directed by Engr-in-charge |
| 14 | S&F 3 mm thick figured sheet glass ordinary quality fixed with alumimium frame works n exc 0.50 sqm in each pane complete all as specified and directed by Engr-in-Charge |
| 15 | S&F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of Zinc Chrome primer complete all as specified and as directed by Engr-in-charge |
| 16 | All as per item No. 15 above hereinbefore but without glazing bars for gauzed shutter including one shop coat of Zinc Chrome primer complete all as specified and as directed by Engr-in-charge |
| 17 | Steel window or ventilator, fixed type with glazing bar complete all as specified and as directed by Engr-in-charge |
| 18 | S &F in repairs curtain rails / hoarrision rail mild steel chromium plated with fixing brackets, stop, roller etc complete all as specified and as directed by Engr-in-charge |
| 19 | M&L for framed work such as grills, grating, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways railing framework of water tank and siliar work complete all as specified and as directed by Engr-in-charge |
| 20 | M&L for two coat of synthetic enamel paint over a coat of red oxide including preparation of newly steel surfaces complete all as specified and as directed by Engr-in-charge |
| 21 | S&F for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125x60mm complete all as specified and as directed by Engr-in-charge |
| 22 | S&F for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 105x60mm complete all as specified and as directed by Engr-in-charge |
| 23 | S&F of factory made plain framed pannelled door shutters 35mm thick (two layer panel) with lock rail and panel of 9mm BWP commercial ply or 12mm verneering on both faces. The size of rail and stile as per IS-1003, SSR Pt-I kiln seasoned and chemically treated complete all as specified and as directed by Engr-in-charge |
| 24 | M&L 35mm thick 2nd class hard wood glazed and skeleton shutter factory made open revated and prepared to receive glass, guage etc with plain chamfered or rounder mitred and rebated, sash bars in any numers divided into squares edges of framing, plain or chamfered or roundedcomplete all as specified and as directed by Engr-in-charge |
| 25 | M&L for two coats of synthetic enamel paint over a coat of pink primer including preparation of new wood and wood based surface, over 10cm width or girth complete all as specified and as directed by Engr-in-charge |
| 26 | S&F 30mm thick flush shutters, solid cor construction with block board core and plywood face panels commercial type on both side as in cup board shutter etc complete all as specified and as directed by Engr-in-charge |
| 27 | M & L as in repair 18/19mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with necessary clips fixed with screws to timber frame work including dismatling of any type of boards complete all as specified and as directed by Engr-in-charge |
| 28 | S&F 100 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by Engr-in-charge |
| 29 | S&F powder coated aluminum (min thickness of powder caoating 50 micron) work for doors, windows, ventilator and partition (fixed portion) with extruded built up standard tubular section / appropriate Z section and other section of approved make confirming toIS:733 and IS:1285 , fixing with dash fastner of required dia and size including necessary filling up the gaps at junction i.e. at top, bottom and side with required EPDM/neoprene gasket etc , aluminium section shall be smooth , rust free,straight, mitred and jointed mechanically wherever required including cleat angle, alumunium snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architechtural drawing andcomplete all as specified and as directed by Engr-in-charge |
| 30 | S&F powder coated aluminum (min thickness of powder caoating 50 micron) for shutter of r doors, windows, ventilator including providing and fixing hinges /pivot and making provision for fixing of fittings wherever required including the cost fo EPDM rubber/neoprene gasket required (fitting shall bepaid for seperately) with extruded built up standard tubular section / appropriate Z section and other section of approved make confirming toIS:733 and IS:1285 , fixing with dash fastner of required dia and size including necessary filling up the gaps at junction i.e. at top, bottom and side with required EPDM/neoprene gasket etc , aluminium section shall be smooth , rust free,straight, mitred and jointed mechanically wherever required including cleat angle, alumunium snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architechtural drawing complete all as specified and as directed by Engr-in-charge |
| 31 | Supply only 5.5 mm thick sheet glass fixed to aluminum frame work with and including standard anodized aluminum bead, rubber packing, aluminum screws etc, in panels n exc 0.5 Square metre in each pane, complete all as specified and as directed by Engr-in-charge |
| 32 | Demolition of brick work built in cement mortar including pillar etc below/ above ground level etc and removing to a distance not exc 50 meter. complete all as specified and as directed by Engr-in-charge |
| 33 | Material and labour for brick work with sub class ‘B’ bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg / Sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by Engr-in-charge |
| 34 | Material and labour for burnt brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar ( 1:6) all as specified and directed. |
| 35 | Taking down cement plaster from brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engr-in-charge |
| 36 | M&L for rendering 15 mm thick on fair faces of brick work or concrete sur-faces in cement mortar 1:4 using water proofing compound as per manufacturer instructions for finished even and smooth (without using extra cement) (WPC will be measured and paid separately) complete all as specified and as directed by Engr-in-charge |
| 37 | M&L for rendering 15mm thick on Surface other then fair faces of brick work or concrete surfaces even and smooth without using extra cement in CM 1:6 complete all as specified and as directed by Engr-in-charge |
| 38 | Supply only liquid water proofing compound complete all as specified and as directed by Engr-in-charge |
| 39 | M&L for prepration of newly plastered surface and appplying two coats of cement base paint complete all as specified and as directed by Engr-in-charge |
| 40 | M&L preparation of new plastered surfaces of wall and appying two coats of oil bound distemper over 1 mm thick wall care putty complete all as specified and as directed by Engr-in-charge |
| 41 | S& F in repairs stainless steel kitchen rack of minimum size 600 x 900x250mm fixing complete all as specified and as directed by Engr-in-charge |
| 42 | Taking down of shutters of any description exc 1 sqm and but n.exc 2 sqm each complete all as specified and as directed by Engr-in-charge |
| 43 | M&L 18 mm thick solid PVC sheet plelaminated economic/economic colour both side , cut according to the size of the cabinet or for kitchen drawer provided and the groove to be made on the one edge so that the overlapping could be done for double leaf shutter including fixing with 1.25\\" Mild steel screw to the frame with the channel , complete the work according directions of Engineer-in-Charge, Including dismantling of any type of Board complete all as specified and as directed by Engr-in-charge |
| 44 | M&L 9 mm thick solid PVC sheet plelaminated economic/economic colour both side , cut according to the size of the cabinet or for kitchen drawer provided and the groove to be made on the one edge so that the overlapping could be done for double leaf shutter including fixing with 1.25\\" Mild steel screw to the frame with the channel , complete the work according directions of Engineer-in-Charge, Including dismantling of any type of Board complete all as specified and as directed by Engr-in-charge |
| 45 | S&F telescopic drawer channel 20 inch steel silver chrome plated fixed with mild steel screw to the frame with cannel complete all as specified and as directed by Engr-in-charge |
| 46 | S&F sainless steel handles 100 mm fixed with screw complete all as specified and as directed by Engr-in-charge |
| 47 | Auto close stainless steel (clip hinges) 75mm size suitable for cupboard shutter fixed in position with stainless steel screws, fixed as in repairs complete all as specified and as directed by Engr-in-charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender