Tender For Addn/Altn To Boundary Wall And Provn Of View Cutters At Mes Complex At Af Stn Bhowali.
Tender Value
1.06 Crore
Estimated cost
Bid Submission
14 Sep 2026
22 days left
EMD
1.81 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nainital → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addn/Altn To Boundary Wall And Provn Of View Cutters At Mes Complex At Af Stn Bhowali.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling wrought iron or mild steel work of any description not otherwise provided for angle Post etc complete all as specified and directed. |
| 2 | S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161, grade St. 240 as in frame work for sun shade, roof projection and vertical section etc complete all as specified and directed. |
| 3 | S&F for Rolled Mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming Fe 410-W(Gde-E-250 Quality-A) complete all as specified and directed. |
| 4 | S & F for Rolled Mild steel in Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc. complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, Fe 410-W (Gde-E-250) quality-A,etc complete all as specified and directed. |
| 5 | Excavating in post holes (or similar holes) each n exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and getting out in any type of soil complete all as specified and directed. |
| 6 | M & L for PCC 1:3:6, Type C2 (40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 7 | M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 8 | S & F Pre-painted galvalume aluminium zinc GI based profile pattern steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa with AZ150 (150 g/Sqm total both sides) coating as in roof covering/cladding to wall, fixed with self tapping screws and EPDM washers as specified and directed. Note:- 1. The Pre-painted galvalume aluminium zinc GI based profile pattern steel sheet should be JSW AZ150 Colouron Plus Sheet or equivalent as approved by Engr-in-Charge. 2. Rate includes for make to shape in any curvature, radius or angle as directed by Engr-in-Charge. |
| 9 | Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 10 | Demolition of brick work built in cement mortar including all quoins ,arches , pillars etc complete all as specified and directed. |
| 11 | Demolition of reinforced cement concrete in ground floors and paving n exc 15 cm thickness (below or above ground floor) including reinforcement cut as required to facilitate demolition complete all as specified and directed. |
| 12 | M&L for Mild steel bars (TMT bars) 5mm dia and over upto and including 10mm dia in strriups,spacers,nibs and binders complete all as specified and directed. |
| 13 | M & L for high strength steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips, etc complete all as specified and directed. |
| 14 | M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete complete all as specified and directed. |
| 15 | M & L for formwork to sides and soffits of floor or roof beam, beam haunchings, bands, girders, bressummers, lintels, etc for fair finished surfaces complete all as specified and directed |
| 16 | M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as specified and directed |
| 17 | M&L for Brick work with sub class 'B' bricks, straight or curved on plan exc. 6.00m mean radius, built in cement mortar 1:6, etc complete all as specified and directed. |
| 18 | M&L for PCC 1:4:8 Type D2 (40mm graded stone aggregate) as in foundation complete all as specified and directed. |
| 19 | M&L for M-20 (Nominal Mix) using 20 mm graded stone aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc and mass concrete complete all as specified and directed. |
| 20 | M&L for M-20 (Nominal Mix) using 20 mm graded stone aggregate as in beams, bands, cantilevers, bressummers, lintels, chajjas, etc over 1.5m span etc complete all as specified and directed |
| 21 | M&L for M-20 (Nominal Mix) using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 22 | M&L for rendering 15mm thick cement plaster in CM 1:4 on fair faces of brick or concrete surface with liquid water proofing compound @ 200 ml per bag finished even and fair without using extra cement complete all as specified and directed. (Note:- Liquid water proofing compound to be measured and paid separately) |
| 23 | Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or equivalent complete all as specified and directed. |
| 24 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon addisives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 25 | S&F in repair Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured) complete all as specified and directed. |
| 26 | Providing and fixing concertina coil fencing with punched tape concertina coil 610 mm dia 10 meter openable length, having 50 Nos rounds per 6 metre length (before stretching), on ‘Y’ shaped angle iron brackets placed 2.4m to 3.00m apart, stud tied with GI staples and GI clips to retain horizontal, including necessary bolts or GI barbed wire tied to angle iron, with reinforced barbed tape (R.B.T.)/ spring core (2.5mm thick) wire of high tensile strength of 165 kg/sqcm with tape (0.52mm thick) and weight 43.478 gm/mtr complete all as specified and as directed including taking down existing rusted coil.Note: (i) Angle iron supports shall be measured and paid separately under relevant items of Schedule ‘A’ (ii) Measurement shall be made for stretched length. |
| 27 | Supply and fixing 16 mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.50 cm but n exc 30 cm long complete all as specified and directed |
| 28 | S & F Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe.290.Gde-E-165 complete all as specified and directed |
| 29 | S & F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 30 | S & F of PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 31 | Raking or circular cutting; cutting holes for galvalume corrugated sheet, notchings. etc. including waste on corrugated sheet (any thickness) complete all as specified and directed. |
| 32 | S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; complete all as specified and directed. |
| 33 | Cutting/Drilling holes in brick walls exc half brick wall but n exc one brick wall in mud mortar for inserting holdfasts or Screw bolt on wall and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete all as directed and specified. |
| 34 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed. |
| 35 | Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/disintegrated rocks complete all as specified and directed. |
| 36 | Removing surplus excavated materials (rocks) to a distance exc 250 m but n exc 500 m & depositing where directed at a level not exc 1.5 Mtr above the starting point. |
| 37 | M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub-base finished to receive floor treatment etc complete all as specified and directed. |
| 38 | M & L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors and pointed with grey cement and no pigment over 20 mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 39 | M&L for PCC 1:2:4 type B-1 (20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysSep 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 29 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender