Tender For Annual Contract For Petty Repair And Water Proofing Maintenance Works At Office And Residential Complex, Amd, special repair
Tender Value
4.76 Lakhs
Estimated cost
Bid Submission
07 Sep 2026
18 days left
EMD
9539
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bengaluru Urban → Karnataka
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Annual Contract For Petty Repair And Water Proofing Maintenance Works At Office And Residential Complex, Amd, special repair
BOQ
| Sl. No. | Item Description |
| 1 | General Notes:1. Contractor shall inspect the site to acquaint with the site conditions as well as security conditions at AMD.2. The rates quoted shall include cost of all tools and tackles, manpower including wages, liveries, all wastages and taxes GST, Labour cess, IT, etc., as applicable but exclusive of EPF and ESI .EPF and ESI are reimbursable as per relevant clause. |
| 2 | Making grooves of 5mm width in the existing flooring tile joints and Grouting the joints using epoxy grout mix of approved make at 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including masking the both edges of the joints with mask tape before filling / grouting and finishing complete as per direction of E.I.C. |
| 3 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer- In-charge complete in all respect. (a) SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 4 | (b) Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make |
| 5 | Fixing/Refixing glazed/ Ceramic/ Vitrified floor or wall tiles with more than 6mm thickness cement based high polymer modified quick-set tile adhesive of approved make conforming to IS:15477 as per specifications and direction ofE.I.C. complete in all respect. |
| 6 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75 mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). (a) 12 mm average thickness. |
| 7 | 25 mm average thickness in 2 layers. |
| 8 | 50 mm average thickness in 3 layers. |
| 9 | Chipping of unsound/weak concrete material (75 mm average thickness) from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge. |
| 10 | Providing, mixing and applying SBR polymer (of approved make @ minimum 2% by wt. of cement used) modified plain/reinforced cement concrete for structural members having minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria] with specified average thickness.Note: Rates shall be for finished surface area of concrete and shall include the cost of labour, concrete and appropriate approved Super-Plasticiser for rendering concrete as flowable and SBR polymer but shall exclude cost of reinforcement, bond coat, Shear Keys, centering and shuttering, strutting, propping etc (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) (a)50 mm thick in Grade M25 with cement content not less than 330 kg per cum |
| 11 | (b)75 mm thick in Grade M25 with cement content not less than 330 kg per cum |
| 12 | Water proofing treatment of Vertical joints (of external side and internal side) between door frame, window & ventilator frames (on all four sides) of outer wall over the Zycosil/equivalent & Zycoprime/equivalent solution already applied (before the installation of door / window / ventilator frames in position) and fine finish with Grout RW/equivalent. |
| 13 | Water proofing treatment of RCC sunshade with Zycosil/equivalent water proofing Solution (1 litre of Zycosil/equivalent & 20 litres of water stirred first & 2 litres of Zycoprime/equivalent added and stirred (total 23 litres)) till it meets the saturation level and testing as per RILEM or by water drops test in which water drops do not absorb but drops remain or rolls |
| 14 | In-filling / sealing of joint between RCC lintel cum sunshade and wall (on external side) in all floors by pushing in Grout RW/equivalent in paste form and coving 20 mm x 20 mm after applying a coat of Zycosil/equivalent & zycoprime/equivalent solution before cement plastering of top, bottom and sides of RCC sunshade. |
| 15 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of E.I.C. |
| 16 | Safely removal of tile work in floors and roofs and stacking the tiles in reusable condition which can be relaid by removal/cleaning of hardened mortar within 50 metres lead as per specification and directions of E.I.C. |
| 17 | Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand) |
| 18 | Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level in Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 19 | Providing and laying half block masonry with factory made Precast concrete solid blocks of 100 mm thickness of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in Cement mortar 1:4(1 cement : 4 coarse sand) |
| 20 | Providing and laying half block masonry with factory made Precast concrete solid blocks of 100 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level in Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 21 | Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line for grouting including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of E.I.C. |
| 22 | Providing and injecting approved Epoxy injection grout in concrete/RCC work in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of E.I.C. (The payment shall be made on the basis of actual weight of approved grout injected.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysSep 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender