Tender For Special Repair To Building Number T-71(1), T-71(2/3), T-71(4/5), T-71(6/7), T-71/1(5/6), T-71/1(7/8), T-71/1(9/10) And T-71/1(11/12) ( 19 X Rooms Tent Type Quarters) At Dunkrik Lines Under Age B/R-Ii Ge(Central) Khadki .
Tender Value
78.74 Lakhs
Estimated cost
Bid Submission
17 Sep 2026
25 days left
EMD
1.43 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Building Number T-71(1), T-71(2/3), T-71(4/5), T-71(6/7), T-71/1(5/6), T-71/1(7/8), T-71/1(9/10) And T-71/1(11/12) ( 19 X Rooms Tent Type Quarters) At Dunkrik Lines Under Age B/R-Ii Ge(Central) Khadki .
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling plain or corrugated asbestos sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed by Engineer- in- charge . |
| 2 | S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 as in ridge, roof covering and fixed with self tapping screws complete all as specified and as directed by Engineer- in- charge . |
| 3 | S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer- in- charge . |
| 4 | Dismantling timber framed work scantlings 40 sq.cm and over in section, in any position complete all as specified and as directed by Engineer- in- charge . |
| 5 | All as per ser item No 04 above but in fillets, rails, posts, rafters,purlins etc under 40 sq. cm in section complete all as specified and as directed by Engineer- in- charge . |
| 6 | S & F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe-410 W(Gde E-250) quality B complete all as specified and as directed by Engineer- in- charge . |
| 7 | S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction but welded tubes confirming to I.S. 1161-1979 grade St. 240 etc as in purlins complete all as specified and as directed by Engineer- in- charge . |
| 8 | M & L for preperation of new steel surfaces of any desciption over 10 cm in width or girth not other wise descibed and applying two coats of synthetic enamell paint over a coat of red oxide complete all as specified and as directed by Engineer- in- charge . |
| 9 | Taking down Chowkats or frames with shutters without taking of shutters from the frames exc 1.5 Sqm but not exc 4 Sqm each including complete all as specified and as directed by Engineer- in- charge . |
| 10 | Taking down Chowkats or frames with shutters without taking of shutters from the frames not.exc 1.5 Sqm each complete all as specified and as directed by Engineer- in- charge . |
| 11 | Taking down steel window / ventilator of any description n exc 1.8 sqm each complete all as specified and as directed by Engineer- in- charge . |
| 12 | S&F for powder coated(Powder coating shall not be less than 50 micron of approved colour) aluminium sliding windows having three Nos of tracks including one wire glazed shutters for mosquito proofing including stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm and two Nos glass shutters including 4mm thick coloured glass and aluminium section weight n.less than 0.55 Kg/RM including necessary cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, suitable handles, locking arrangement and fixed to stone masonry wall complete all as specified and as directed by Engineer- in- charge . Note : Glass & wire mesh shall be deemed to be incuded under unit rate quoted. |
| 13 | S&F for powder coated (Powder coating shall not be less than 50 micron of approved colour) anodised aluminium ventilator shutters, fixed type without sash bar including stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.and fixed to stone masonry wall complete all as specified.Note : Glass & wire mesh shall be deemed to be incuded under unit rate quoted. . |
| 14 | S&F factory made 35 mm thick plain framed panelled shutter (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with Commercial veneered on both faces the size of rail and style as per IS-1003 ( Pt-I) kiln seasoned and Chemically pressed of 2nd class hard wood complete all as specified and as directed by Engineer- in- charge . |
| 15 | S&F 105x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed by Engineer- in- charge . |
| 16 | S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed by Engineer- in- charge . |
| 17 | M&L for PCC M-15 grade (nominal mix) using 12.50mm graded stone aggregate as in filling of pressed steel chowkat, sub base & sub floor complete all as specified and as directed by Engineer- in- charge . |
| 18 | S & F factory made 35 mm thick glazed & skeleton shutter of 2nd class hard wood open rebated and prepared to receive gauge (divided into squares with sash bars) edges of framing plain chamfered or rounded, fitted without & fitted beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I Sec-8 clause 8.23 (a) and fitted to chowkhats complete all as specified. |
| 19 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainlesssteel wire staples . |
| 20 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed by Engineer- in- charge . |
| 21 | S&F 30mm thick FACTORY MADE MOULDED DOOR SHUTTER ‐ WOOD FREE consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 25mm x 25mm for stiles, top and bottom rails. M. S. frame shall have a coat of steel primers. The inner panel shall consist of 25mm thick EPS of Density 23 Kg /Cbm. bonded with 2mm thick termite proof, water proof and fire resistant moulded PVC Sheet Manufactured by an ISO‐9001‐2015 certified company, with 2, 4, 6 raised panel design in different plain and / or prelam colours after routing the Moulded design on one side & 2mm plain and /or prelam PVC sheet on other side of the EPS. The edge of panel to be sealed with lipping of 15mm wide PVC sheet baton ( made by sticking 2mm rigid foam PVC sheets of 5mm (±0.25) thickness using PVC solvent cement ) and stile sides 25mm (5mm x 5nos.) thick and 30mm width PVC Sheet fitted along M.S. tube for hardware provision & for lock 25mm thick ( 5mmx5nos. ) PVC sheet of size 150mm x 200mm fixed with inner side of EPS Panel etc. complete all as specified and as directed by Engineer- in- charge . all as specified and as directed by Engineer- in- charge . |
| 22 | S&F Butt Hinges medium weight cold rolled stainless steel 100 mm long complete all as specified and as directed by Engineer- in- charge . |
| 23 | S&F 150mm long Aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed by Engineer- in- charge . |
| 24 | S&F for Extruded aluminium alloy handles 150 mm, fabricated type, anodised complete all as specified and as directed by Engineer- in- charge . |
| 25 | S&F for mild steel sliding door bolts, plate type, with stainless steel bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified and as directed by Engineer- in- charge . |
| 26 | S&F for mild steel sliding door bolts, plate type, with stainless steel bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 200mm long complete all as specified and as directed by Engineer- in- charge . |
| 27 | Dismantling of floor hearth or wall tiling including cm bedding (but not backing) removing serviceable tiles in store rubbish of the premises complete all as specified and as directed by Engineer- in- charge . |
| 28 | M&L for vitrified ceramic tiles 8-10 mm thick light shade, (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed by Engineer- in- charge . |
| 29 | M&L for Vitrified coloured tiles in vertical/skirting surface 8 - 10 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile over and including 10 mm thick cement plaster 1:4 as in backing coat & triangular filleting on top tile in CM 1:3 complete all as specified and as directed by Engineer- in- charge . |
| 30 | M&L for 25 mm thick Cement concrete in level course for receiving floor tiles using PCC M-15 grade (Nominal Mix) using 20 mm graded stone aggregate) complete all as specified and as directed by Engineer- in- charge. |
| 31 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding .11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer- in- charge . |
| 32 | M&L for Glazed ceramic coloured tiles in vertical surface 300x600x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile ,over and including 10 mm thick cement plaster 1:4 as in backing coat & triangular filleting on top tile in CM 1:3 complete all as specified and as directed by Engineer- in- charge . |
| 33 | Taking down cement plaster on brick or stone walls, ceiling etc. including racking out joints, hacking for key, scrubbing down with water complete including removing the same to low laying aera out side the primeses complete all as specified and as directed by Engineer-in-Charge. |
| 34 | M&L for Pre-cast cement concrete block masonry of PCC 1:3:6 Type C1 using 20mm graded stone aggregate with solid blocks straight or curved on plan , exc 6m mean radius and exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. |
| 35 | M&L rendering 15 mm thick (10mm + 5mm) plaster on fair face of brick/ PCC block masonry wall in CM 1:4 and finishing surface even and fair by mixing liquid water proofing compound as per manufacturers instructions complete all as specified and as directed by Engineer -in-Charge.Note:- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ |
| 36 | M & L for rendering 10 mm thick on fair faces brick work /PCC block masonary or concrete surface of wall using cement plaster 1:6 and finished even and smooth (without using extra cement) complete all as specified and as directed by Engineer- in- charge . |
| 37 | M & L preparation of newly plastered surface and applying two coat of cement base paint on wall including priming plastered and other surfaces with alkali resistant priming paint etc complete all as specified and as directed by Engineer- in- charge . |
| 38 | M & L preparation of newly plastered surface and applying two coat of oil bound Distemper over a coat of primer on wall etc complete all as specified and as directed by Engineer- in- charge |
| 39 | Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS-1239 (Part-1) : 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed. |
| 40 | Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1) : 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed. |
| 41 | S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed by Engineer- in- charge . |
| 42 | S&F in repairs Plastic water closet seat cover, coloured, for pedestal pan closed pattern with flat bottom,and cover with mild steel chromimium plated or aluminised hinging device complete all as specified and as directed by Engineer- in- charge . |
| 43 | S&F in repair angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bpre of pipe complete all as specified and as directed by Engineer- in- charge . |
| 44 | S&F in repairs Vitreous china wash basin white flat back size 550x400 mm excluding taps but including 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets all as per makes specified in PS complete all as specified and as directed by Engineer- in- charge |
| 45 | S&F in repairs 15 mm bore Pillar taps, cast copper alloy fancy type, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as per makes specified in PS complete all as specified and as directed by Engineer- in- charge . |
| 46 | S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engineer- in- charge . |
| 47 | S&F in repairs Bib taps 15mm dia, cast copper alloy chromium plated, with CP flange makes specified in PS fixed in repairs complete all as specified and as directed by Engineer- in- charge . |
| 48 | S&F in repairs Stop valve fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle,15mm bore size screwed both ends for iron pipe or for unions and fittings complete all as specified and as directed by Engineer- in- charge . |
| 49 | S&F in repair for CP Health Faucet ABS Body with 1 Meter Flexible tube & Hook complete all as specified and as directed by Engineer- in- charge . |
| 50 | S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engineer- in- charge . |
| 51 | S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, complete all as specified and as directed by Engineer- in- charge . |
| 52 | M&L for PVC (SWR) gully trap 125/110mm setting and jointing in solvent cement complete all as specified and as directed by Engineer- in- charge . |
| 53 | M&L for 75mm bore PVC (SWR) pipe, type 'B' single socketed in any length with rubber ring joints laid in trenches or floors fixed in repairs all as specified and as directed. |
| 54 | M&L for 110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to wall including PVC clamps and necessary fittings fixed in repairs complete all as specified and as directed by Engineer- in- charge . all as specified and as directed. |
| 55 | S&F for 100 mm bore Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete M-15 grade using 20mm graded stone aggregate PVC (SWR) fixed in repairs complete all as specified and as directed by Engineer- in- charge . |
| 56 | Dismantling of wall and ceiling boards (fibre,pulp insulation, Ac etc), any thickness including cover fillets complete all as specified and as directed by Engineer- in- charge . |
| 57 | S&F interlocking aluminium alloy anodised snap grid consists of main Tee runners of size 38mm x25mm x1.5mm spaced 1200mm centre to centre and cross Tee of size 25mmx25mmx 1.5mm, 1200mm long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mmx600mm and provide a secondary cross tee 25mm x1.4mm ( of length 600mm) to be interlocked of the centre of 1200mmx600mm panel to form a grid of 605mmx605mm and wall angle 25mmx25mmx 2mm. Aluminium alloy extruded section shall be aluminium anodised (minimum 15 micron ) and shall conform to IS 733, IS 1285 and IS 737. including Hangers of GI wire 6mm dia to be fixed by approved rawl plug, level and justers and screws etc. |
| 58 | M&L for 8-9 mm thick Gypsum board/tiles for insulation and acoustic purposes, 60cmx60cm in size , on snap grid in ceiling. |
| 59 | Demolition of stone slabs/flooring of any description laid bedded and pointed any mortar and all as directed. |
| 60 | M&L for 20 - 25 mm thick machine cut machine polished Kota stone slab flooring laid and jointed in neat cement slurry mixed with pigment to match the shade including cutting and polishing and laid over and including 15 mm thick screed bed in CM 1:3 complete all as specified and directed by Engr-in-Charge. |
| 61 | M & L for one piece machine cut Kota stone 20-25 mm thick slab, as in treads of stairs etc., laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed or bedding layer of mortar 10 mm thick in Cement Mortar 1:3 complete all as specified and as directed including roughening of existing concrete surface.The edges of treads shall be half moulded and three Nos longitudinal grooves are to be provided to make the stair non slippery, complete all as specified and as directed by Engineer- in- Charge |
| 62 | M&L for Granite slab/sill/jump of door window machine cut for 20 mm thick bedded and jointed with colour cement to match cut to shape required incl screed base in cm 1:4 complete all as specified and as directed by Engineer- in- Charge |
| 63 | M&L for Machine cut cudappah stone slab 20-25mm thick laid over 15 mm thick in cement mortar cement screed base in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer- in- charge . |
| 64 | Dismantling of precast interlocking tiles/ paver blocks, chequered tiles of any description thickness & size complete all as specified and as directed by Engineer- in- charge all as specified |
| 65 | M&L for Crushed stone grid filling under floors 25mm thick compacted bed , compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints complete all as specified and as directed by Engineer- in- charge |
| 66 | M & L for 75mm thick M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate as in sub base for paver block complete all as specified and directed |
| 67 | M&L for providing 60 mm thick machine pressed precast concrete interlocking paver blocks of any shape and size conforming to IS-15658-2006,with grey cement and pigment, rubber moulded tiles M-35 Grade, as in floors,paving,path etc.complete all as specified and as directed by Engineer- in- charge . |
| 68 | S&F rotational moulded polyethylene water storage tanks three layer having capacity 500 litres ( cylindrical vertical with closed top ) hoisted and fixed in position including dismantling and removing of old tank complete all as specified and as directed by Engineer- in- charge. |
| 69 | Demolition and breaking up drain pipes ( salt glazed ware AC/RCC) drain pipes set in cement mortar, dia of pipe 200mmremoving the same off the primes complete all as specified and as directed by Engineer- in- charge . |
| 70 | Excavating in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth; for foundation , laying of cable etc or for manholes, laying pipes etc and getting out in hard / dense soil. |
| 71 | Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for (below or above GL)complete all as specified and as directed by Engineer- in- charge. |
| 72 | Demolition of Brick / PCC solid block masonry or stone masonry built in cement mortar/cement lime mortar including removing the debris off the premisses complete all as specified and as directed by Engineer- in- Charge |
| 73 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position below or above ground floors, not exceeding 15 cm in depth and removing the material of the premises complete all as specified and as directed. |
| 74 | M&L for cement concrete M-10 grade( Nominal Mix) using 40 mm graded stone aggregate as in concrete bed to drain pipes including packing under & haunching against sides of pipes after they are laid and tested for 150 mm complete all as specified and as directed by Engineer- in- charge all as specified and as directed. |
| 75 | M&L cement concreteM-7.5 grade ( Nominal Mix) using 40 mm graded coarse aggregate in foundations filling & mass concrete complete all as specified and as directed by Engineer- in- charge . |
| 76 | M&L for reinforced concrete pipes, 150 mm bore, Class NP-2, laid and jointed complete all as specified and as directed by Engineer- in- charge . with collars. |
| 77 | M&L for PCC M-15 grade ( Nominal Mix) using 20 mm graded coarse aggregate in coping including necessary formwork and benching in bottom of manholes drain etc complete all as specified and as directed by Engineer- in- charge .complete all as specified and as directed by Engineer- in- Charge. |
| 78 | M&L rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces and finishing the surfaces even and smooth without using extra cement including 3% WPC complete all as specified and as directed by Engineer- in- charge . all as specified and directed Note: WPT shall be measured and paid separately under relevant item of this BoQ. |
| 79 | Supplying only integral water proofing compound. |
| 80 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed by Engineer- in- charge . |
| 81 | Returning, filling, including spreading levelling, watering and well ramming in layers not exc 25cm complete all as specified and directed by Engr-in-Charge. |
| 82 | Removing excavated soil n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point. |
| 83 | M&L for precast cement concrete M-15 grade (Nominal Mix) using 20 mm graded coarse stone aggregate in cover slab set in CM 1:6 complete all as specified and as directed by Engineer- in- Charge |
| 84 | M&L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bend to shape required, including cranking, bending and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed by Engineer- in- charge . |
| 85 | M&L for 75mm thick PCC M-10 grade (nominal mix) using 20mm graded stone aggregate as in plinth protection/path finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed by Engineer- in- charge .. |
| 86 | M&L preparation of wooden surfaces of any description exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed by Engineer-in- Charge. |
| 87 | Cutting existing GI water pipe line 40/50 mm dia in position for inserting tee/specials for branch connection of 40 mm size complete all as specified and as directed by Engineer- in- charge . all as directed. |
| 88 | Supplying & laying in trenches 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed. |
| 89 | Supplying & laying in trenches 40 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed. |
| 90 | S&F in repair gun metal gate valve with iron wheel head, screwed both ends for iron pipes 20mm bore complete all as specified and as directed by Engineer- in- charge . |
| 91 | S&F in repair gun metal gate valve with iron wheel head, screwed both ends for iron pipes 40mm bore complete all as specified and as directed by Engineer- in- charge . |
| 92 | Taking down copper/aluminium point wiring ( light, fan, socket, power ) complete all as specified and as directed by Engineer- in- charge ., including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surface of walls, floors, etc |
| 93 | Taking down carefully submain wiring any size complete. |
| 94 | Taking down old and unserviceable main incoming MCB DB TPN/ main switch along with MCCBs/MCBs and making good the disturbed surface all as directed specified and directed. |
| 95 | M & L for point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories along with one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, regulators or bell push and casing capping terminal box for mounting ceiling rose/ holders etc all as specified and directed by Engr-in-Charge for the followings. |
| 96 | One light point controlled by one, one way switch on independent board |
| 97 | One fan point controlled by one, one way switch on independent board |
| 98 | One three pin 6 Amp socket outlet on independent board |
| 99 | One three pin 6 Amp socket outlet on same board |
| 100 | One bell/ buzzer point controlled by one, one way switch on independent board |
| 101 | All as per item No 95 but FRLSH copper stranded cable of size 2.5 sq mm for 6 pin socket outlet 16 amp on one independent board. along with all fitting and accessories and making good the distrubed suface to match with exsiting complete all as specified and as directed by Engineer- in- charge . |
| 102 | M & L for sub main wiring with two single core PVC insulated multi stranded FRLSH Copper conductor cable of size 4 sqmm drawn through in and including PVC Conduit of suitable size with all accessories and one single core green colour FRLSH Copper conductor cable of size 4 sqmm as earth wire and connected to earth dolly and making good to disturbed surfaces .NOTE:-(i) Two run of 4 sqmm Copper conductor cable with one run 4 sqmm earth wire and one run of PVC Conduit of suitable size shall be be measured as one unit length. (ii) Extra length of cable required for connection to DBs/ MCBs shall deemed to be included in unit rate quoted by the contractor against this item.(iii) Earth wire run inside the PVC conduit. |
| 103 | M & L for sub main wiring with two single core PVC insulated multi stranded FRLSH Copper conductor cable of size 6 sqmm drawn through in and including PVC Conduit of suitable size with all accessories and one single core green colour FRLSH Copper conductor cable of size 6 sqmm as earth wire and connected to earth dolly and making good to disturbed surfaces complete all as specified and as directed by Engineer- in- charge . .NOTE:-(i) Two run of 6 sqmm Copper conductor cable with one run 6 sqmm earth wire and one run of PVC Conduit of suitable size shall be measured as one unit length. (ii) Extra length of cable required for connection to DBs/ MCBs shall deemed to be included in unit rate quoted by the contractor against this item.(iii) Earth wire run inside the PVC conduit. |
| 104 | S&F 6 Amp, 240 Volt switch Piano flush type single pole one way all as specified and as directed by Engr-in-Charge. |
| 105 | S&F socket flush type 6 amps, 5 pin, 240v all as specified and as directed by Engr-in-Charge. |
| 106 | S&F switch socket combination multipurpose 2-in-1 flush type 5 pin 16 amps and 6 amps, 240v with fuse and neon indicator complete all as specified and as directed by Engr-in-Charge. |
| 107 | S&F fan regulator 5 step type, 120 volt, 2 module complete all as specified and as directed by Engr-in-Charge. |
| 108 | S&F bell push piano flush type one way, 6 Amps, 240 volt complete all as specified and as directed. |
| 109 | S&F call bell electric, ding dong, AC 240 volt, 50 HZ. incl dismantling taking down unsv one all as specified and as directed. |
| 110 | S&F ceiling rose surface Bakelite three terminal all as specified and as directed by Engr-in-Charge. |
| 111 | S&F Angular Lamp holder of PVC/ Polycarbonate type with back plate all as specified and as directed by Engr-in-Charge. |
| 112 | S&F LED lamp 15 watt, 230V, 1500 lumen, cool day light (6500- 7500K) basic round B-22 type PF-0.95 (min) complete all as specified and directed by Engr-in-Charge. |
| 113 | S&F decorative wall mounting fitting made up of polycarbonate rings and glass shade with lamp holders, connector block, 1 x 15 watt LED bulb, glass fitted with engineering plastic with B-22 lamp holder with electrical copper contracts, self scrud polycarbonate in open finish for soothing light effect, LED bulb 15 watt etc complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable complete with taking down old unsv existing holder complete all as specified and directed by Engr-in-Charge. |
| 114 | S&F LED tube light fittings, 20 watt, 4 feet precoated CRCA body heavy duty industrial batten suitable for retrofit LED tube 20 watt including LED tube rod 20 watt self ballasted retrofit lamp with thermoplastic body 270 degree wide distribution CCT 6500 k including fitting fixed on wall/ ceiling and connected up complete with 3 core including taking down existing tube light fifftngs and making necessary connection complete all as specified and directed by Engr-in-Charge. |
| 115 | S&F LED light fitting mirror type with high output diffuser 2 feet, 10 watt, 220 volt AC decorated type with driver holder and LED lamp including connecting up with 3 core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. |
| 116 | S&F LED decorative building security light fitting 30 watt with PDC aluminium body & clear polycarbonate cover wide beam distribution and connecting up complete with 3 core flexible cable white of size 23/0.0076 complete all as specified and directed by Engr-in-Charge. |
| 117 | S&F in repairs bracket for street light fittings made out of 32 mm dia medium grade galvanised steel (GI) tubing of 1.5m long, bend to required shape (having an angle of 120 degree) including necessary FI clamp (02 Nos of size 40 x 5 mm) nuts, bolts & washers and fixing complete all as specified and directed by Engr-in-Charge. |
| 118 | S&F factory made sheet metal enclosure double core vertical type, IP 43 protection, insulated busbar assembly, isolated neutral bar, door earthing, mechanical impact strength IK09, including incoming MCCB 63 Amp, outgoing 4 way optium F1+12 complete all as specified and directed by Engr-in-Charge. Note : The unit rate quoted shall be deemed to include the cost of MCCB triple pole 63 Amp, 16 KA. |
| 119 | S&F prewired distribution board factory made sheet metal enclosure double door distribution board class IP-43, IK-09 with 200 Amps rated copper bus bar, 240 volt, 8 way (2 + 6 way) single pole and neutral link complete all as specified and directed by Engr-in-Charge. |
| 120 | S&F prewired distribution board factory made sheet metal enclosure double door distribution board class IP-43, IK-09 with 200 Amps rated copper bus bar, 240 volt, 4 way (2 + 2 way) single pole and neutral link complete all as specified and directed by Engr-in-Charge. |
| 121 | S&F MCB, Single Pole and neutral (SP&N), 25 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” series with all incoming/ outgoing connections with proper size lugs all as specified and directed by Engr-in-Charge. |
| 122 | S&F MCB, Single Pole (SP), 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’B” series with all incoming/ outgoing connections with proper size lugs all as specified and directed by Engr-in-Charge. |
| 123 | S&F MCB, single pole (SP) 40 to 63 Amps, 240 volts, 10 KA, \\"B\\" series with all incoming/ outgoing connections with proper size lugs all as specified and directed by Engr-in-Charge. |
| 124 | S&F in repairs ceiling fans with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.0 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engineer- in- chargeNote - Old unserviceable ceiling fan deposit to MES store |
| 125 | S&F in repairs exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades and frame and louvers incl making of suitable hole in brick / stone wall for fixing of Exhaust Fan complete all as specified and as directed by Engineer- in- charge . all as directed by Engineer-in-charge.Note - Old unserviceable Exhaust fan deposit to MES store |
| 126 | S&F electric water heater, storage type steel body with glass inner tank and heating element upto 2 KW capacity, 25 litre, BEE 5 Star rated complete all as specified and as directed by Engineer- in- charge . with all accessories such as safety valve, thermostat, NRV, connection piece etc. complete all as specified and as directed by Engineer- in- charge . |
| 127 | Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 including Cutting of existing pipe and connecting in all fitting such as tee bends union elbow reducer etc for connection of water supply for geyser all as directed by Engineer-in-charge |
| 128 | S&F stop valve 15mm bore screwed both ends for concealed pips or unions or fittings all as directed by Engineer-in-charge |
| 129 | S&F bib cock 15mm bore screwed both ends for concealed pipes or union or fittings all as directed by Engineer-in-charge |
| 130 | S&F in repair heavy duty PVC connections pipe with brass hexagonal adopter sat both side 15mm dia and 450 mm long for cold water complete all as specified and as directed by Engineer- in- Charge |
| 131 | S&F in repair heavy duty PVC connections pipe with brass hexagonal adopter sat both side 15mm dia and 450 mm long for hot water complete all as specified and as directed by Engineer- in- Charge |
| 132 | Material and labour for earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and including 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete including taking out old earthing material complete all as specified and as directed by Engineer -in-Charge |
| 133 | Supply, laying, jointing, connecting and testing XLPE insulated PVC sheathed cable, 1100V grade, heavy duty multi stranded aluminium conductor grade cross section area 2.5 core 35 sqmm (earthed) complete all as specified, laid in trenches/ fixed on walls/ poles, passing through pipes etc including connecting up to DBs etc with required lugs, end terminal/ cable glands including taking out/ down old unserviceable cable and disposing off complete all as specified and as directed of the following sizes :- Note : Excavation and earthwork will be measured and paid separately under respective items herein. |
| 134 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of cable and getting out in soft loose soil complete all as specified and as directed by Engineer- in- charge . |
| 135 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of cable and getting out in soft disintegrated rock complete all as specified and as directed by Engineer- in- charge . |
| 136 | Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 (Part I and II) for protection of underground cable of size 20 mm outer dia with all fittings such as clamps. coupler etc laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection complete all as specified and as directed by Engineer- in- charge . Note :- Excavation and earth work shall be measured and paid separately. |
| 137 | M&L for road cutting upto 300mm deep and 200mm wide for crossing GI water pipe line through road including making good the disturbed surface by filling mass concrete complete all as specified and as directed by Engineer- in- charge . Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysSep 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 29 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender