Tender For Development And Repair Of Road From Icha Bazar (Near Ayushman Pharmacy) To Trinath Mandir And Allied Roads (L-0.22 Km) Under annual maintenance contract Ward No. 44 /Sh: Patch Soling, Wbm, Grouting, Pmc, Sand Seal Coat, Drain Etc
Tender Value
24.25 Lakhs
Estimated cost
Bid Submission
25 Aug 2026
1 days left
EMD
48506
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Development And Repair Of Road From Icha Bazar (Near Ayushman Pharmacy) To Trinath Mandir And Allied Roads (L-0.22 Km) Under annual maintenance contract Ward No. 44 /Sh: Patch Soling, Wbm, Grouting, Pmc, Sand Seal Coat, Drain Etc
BOQ
| Sl. No. | Item Description |
| 1 | Flat brick solingProviding and laying flat brick soling layer on prepared subgrade according to lines, grades and cross-section shown on the drawing, filling joints with Earth, free from clay with a Plasticity Index not exceeding 6, watering and rolling the same with three wheeled road roller 80-100 kN as per MoRD Technical Specification Clause 412. |
| 2 | Maintenance of bituminous surface road using Jhama brick aggregateRepair to pot holes by removal of failed material, trimming the sides to vertical and levelling the bottom, cleaning the same with compressed air or any appropriate method, filled with B.M (using jhama brick aggregate & bitumen of VG-30), after applying prime coat at the bottom and tack coat on sides and on bottom (using bitumen emulsion) and compacting, trimming & finishing the surface to form a smooth continuous surface, all as per MoRD technical specification Clauses 1900, 502, 503 and 504. |
| 3 | WBM Gr-3Providing, laying, spreading and compacting brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill up the interstices of coarse aggregate, watering and compacting to the required density 'Grading 3' as per MoRD Technical Specification Clause 405. By Manual Means |
| 4 | Prime Coat (SS-1): Low porosityProviding and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.00 kg/sqm using mechanical means as per MoRD Technical Specification Clause 502. Low porosity. |
| 5 | Tack coat using hot straight run bitumen of grade VG-30 on W.B.M.Providing and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications: On WBM @ 0.75 kg/ sqm. |
| 6 | Tack coat using hot straight run bitumen of grade VG-30 on bituminous surfaceProviding and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications: On bituminous surface @ 0.50 Kg/ Sqm. |
| 7 | Tack Coat (RS-1)Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503. |
| 8 | 20 mm thick open Graded premix carpet using bituminous (Viscosity grade/ modified bitumen) binder.Providing,laying and rolling of open graded premix carpet of 20 mm thickness composed of 13.2mm to 5.6mm aggregates either using penetration grade bitumen or emulsion to required line grade and level to serve a wearing course on a previously prepared base including mixing in a suitable plant laying and rolling with a three wheel 80-100 KN static roller capacity finished to required level and grades to be followed by seal coat of either Type-A or Type-B or Type-C or Type-D as per MORD technical specification clause 508.Case-I. By Manual means.(i) Bitumen (60/70 grade) V.G.-30. |
| 9 | Seal coatProviding and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross full using Type-A or Type-B or Type-C or Type-D as per MORD technical specification clause 510.A. By manual means.Case-IV Type –D (Premix with fine sand), Bitumen VG-30 |
| 10 | Seal coat on old bituminous road surfaceSand seal coat on old bituminous road surface by applying Viscosity Graded (VG-30) bitumen @ 1.00 kg per sqmusing rubber brush after proper cleaning of the road surface and spreading of river sand @ 0.06 cum/10 sqmcomplete as per specification and direction of the Engg.-in-Charge. |
| 11 | 80 mm thick Paver block80 mm thick factory made c.c. interlocking paver block of M-35 GradeProviding and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge:(a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 12 | Factory made kerb stone M-25Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete inposition to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-Charge (length of finished kerb edging shall be measured for payment).(Precast c.c. kerb stone shall be approved by Engineer-in Charge). |
| 13 | Excavation for StructuresWithout dewatering.Earthwork in excavation for structures as per drawing and MoRD technical specifications Clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleterious material and disposal upto a lead of 50 m, dressing of sides & bottom and backfilling in trenches with excavated suitable material.Ordinary Soil, Upto 3 m depth |
| 14 | Sand FillingFilling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200.Sand filling |
| 15 | Providing concrete for plain concrete (using jhama brick aggregate) in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement)PCC grade M 10 (using jhama brick aggregate)Nominal mix 1:3:6 |
| 16 | PCC M-20 in open foundation with nominal mixProviding concrete for plain/reinforced concrete in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement).P.C.C grade M 20(i) Nominal mix (1:2:4) |
| 17 | Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar reinforcement in foundation complete as per drawings & MoRD technical specifications Clauses 1000 & 1202. |
| 18 | Brick work in Foundation 1:4Brick masonry work in cement mortar in foundation completed excluding pointing & plastering as per drawing & MoRD technical specifications Clauses 600, 1202 & 1203.Brick masonry in 1:4 cement mortar |
| 19 | 12 mm plastering in SubstructurePlastering with cement mortar (1:4) 12 mm thick on brick work/ C.C. work including a finishing coat of neat cement punning with 2.75 kg of cement per sqm in substructure as per MoRD technical specification Clauses 613.4 & 1204. |
| 20 | Weep holesProviding weep holes in brick masonry/ stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe or uPVC pipe (110 mm OD of 6.0 kg/cm2 pressure) extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MoRD technical specification clauses 614, 709, 1204.3.7. |
| 21 | Filter media with jhama brick aggregateProviding & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8. |
| 22 | Maintenance of Earthen shoulder (filling with fresh selected soil)Making up loss of material/ irregularities on shoulders to the design level by adding fresh approved selected soil and compacting it with appropriate equipment at OMC upto a lead of 1000 m as per MoRD technical specification Clause 1903. |
| 23 | Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per MoRT&H Technical Specification Clause 803.Over 10 cm in width Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender