Tender For Misc Repairs To Hardstandings, Kerb Stone, Tiles, Fencing And Gates At Ancom, Jal Vihar, Manekshaw Enclave, Mes Accns, Emergency Block, Dweepika, Ge Office And Fmsd Of Age B/R-I Under Ge Haddo, Sri Vijaya Puram
Tender Value
44 Lakhs
Estimated cost
Bid Submission
07 Sep 2026
14 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Misc Repairs To Hardstandings, Kerb Stone, Tiles, Fencing And Gates At Ancom, Jal Vihar, Manekshaw Enclave, Mes Accns, Emergency Block, Dweepika, Ge Office And Fmsd Of Age B/R-I Under Ge Haddo, Sri Vijaya Puram
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete, brick work, masonary etc, including taking out embedded portion and making good disturbed ground complete all as specified and directed by Engr-in-Charge |
| 2 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed withearth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified and directed |
| 3 | M&L for cement concrete 1:2:4 type B1 (Using 20mm graded stone agrregate) as in foundation of posts, railing and similar work complete all as specified and directed |
| 4 | M&L for mild steel work as posts and struts in fencing including cutting tops as required drilling holes, notching for wires etc and similar works conforming to Fe-290 Gde E-165 complete all as specified and as directed |
| 5 | S&F mild steel screw bolt (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, dia of shank 11 to 15 mm and length of bolt exc 5 cm but n. exc 10 cm complete all as specified and as directed |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed |
| 7 | S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works conforming to Fe-290, Gde-E-165 all as specified and as directed |
| 8 | S & F mild steel roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) quality-A complete all as specified and as directed. |
| 9 | S & F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed. |
| 10 | M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm width or girth not otherwise described complete all as specified and directed. |
| 11 | Dismantaling fencing wire mesh of any type and in any position complete all as specified and directed by Engr-in-Charge |
| 12 | S&F for MS Galvanized with 1.00mm thick PVC coated chain link fencing 50mm x 50mm over 3.15mm GI wire including fixed to any type of fencing posts with straining bolts, stiffener rods etc including provision of binding wire if required, etc completed all as specified and as directed |
| 13 | M&L for mild steel round bars 10 to 12mm dia as required, made to shape for securing chain link fencing etc., and similar works conforming to Fe-290 Gde E-165 and including preparation and applying two coats of synthetic enamel paint over a coat of red oxide primer before fixing, etc completed all as specified and as directed. |
| 14 | Dismantling plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof coverings complete all as specified and directed |
| 15 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed |
| 16 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, fixed with self tapping screws all as specified and directed |
| 17 | Dismantling wood boarding, panels, beams or any description, fixed any position with nails complete all as specified and directed. |
| 18 | M&L in repairs to 18 mm thick rubco huat rubwood in built up interiors as in cupboards, shelves wall lining, box structure and including all fitting items complete all as specified and directed. After completing the carpentry works all the visible woods area will be sanding by No.60 & 80 Wood Sanding Paper, after that will be applying Sheenlac make Filler with mixing of NCD Thinner (Sheenlac make), then pasting Chock Putty in the shabby/nailing area which will be sanding with No.120 Sanding Paper, after that will applying Sealer of Sheenlac make and walnut colour stainer, then cutting with No. 320 Sand Paper, after completing the above process will spray Melamine Polish of Berger/Sheenlac make then cutting with No.400 Sanding Paper. Finally will applying Silicon make: Waxpol with soft Banyan Cloth for better shining/finishing. Make of rubber wood members: RUBCO or equivalent |
| 19 | M&L for 30mm thick rubber wood superior quality, chemically pressure treated, egde glued, finger jointed, tongued, grooved as in door shutter and finished with two coats of melamine polish with asian sealer and wood filler over a coat of honey/natural colour wood filler putty for dust free surface etc including preparation and applying three types of sand papers and surface finish to a glossy/ mat finish to match with the adjoining surface complete all as specified and as directed. ake of Rubber Wood members : RUBCO/ India Wood or equivalant |
| 20 | M&L for 18mm thick HDF boarding (Fire and water proof) as in cup boards/shutters/racks/shelves exterior grade with one side white lamination and other side coloured prelaminated, size of the cabinet as per requirement of the site complete all as specified and as directed by Engr-in-Charge. Make : Archidply /Vidya Ply & Board Pvt Ltd/Adarsh Sales Pvt Ltd Note : (i) Cutting edges of cupboard shutter/ shelves to be finished with adhesive edge binding tape all as directed |
| 21 | M & L for preparation of new/old wooden surfaces and applying melamine polish through the process of sanding with wood sanding paper of size 60 & 80 and applying wood filler mixed with NCD thinner including applying wood putty on shabby/ nailing area and sanding with sand paper of size 120 and applying sealer and walnut colour stainer and sanding with sand paper of size 320 and melamine polishing with spray application and again sanding with 400 sand paper and finally applying silicon of make Waxpol with soft fine cloth for better shining and finishing complete |
| 22 | S&F Auto concealed hinges stainless steel grade AISI-316 (type Austenitic anticorrosive in nature) suitable for kitchen cabinets, cub boards, Shelves etc complete all as specified and as directed. |
| 23 | S&F SS Fancy 'D' Type Drawer / Cabinet handles of Size 100mm, etc all as specified and as dierected. Make Prayag Cat No SSB-2100) complete all as specified and as directed. |
| 24 | S&F stainless steel 100mm long tower bolts complete all as specified and directed |
| 25 | S&F Magnetic catcher with plate, glossy finish for Drawer / Cabinet of Size not less than 50mm, etc all as specified and as dierected.Make Prayag Cat No MDC-W55) |
| 26 | S&F Stainless steel Telescopic channel 18 inches length with necessary fitting, etc all as specified and as dierected.Make Godrej Cat No 9721) |
| 27 | Demolition of precast cement concrete block walling built in CM or cement lime Mortar complete all as specified and as directed |
| 28 | M&L precast cement concrete block masonry exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:4 all as specified |
| 29 | Taking down cement plaster on concrete or brick masonry surface including raking out joints, hacking for keys scrubbing down with water etc to receive plaster all as specified. |
| 30 | M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement, etc completed all as specified and as directed. |
| 31 | M&L for new plastered on walls and applying two coats of oil bound distemper over a preparatory coat of 1mm thickess of plaster of paris putty on plastered surface over a coat of priming plastered and other surfaces with alkali resistant priming paint, including necessary preparation of surfaces etc, completed all as specified and directed. |
| 32 | M&L for 15mm thick plaster in CM 1:4 on fair face of brick walls or concrete surface including mixing of liquid water proofing compound @ 200ml per 50 Kg cement bag, finished the surface fair and even without using extra cement complete all as specified and as directed. (Note: Water proofing compound shall be measured and paid separately) |
| 33 | M&L for preparing newly plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed. |
| 34 | M&L for complete removal of existing treatment on plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed |
| 35 | M&L for 10mm thick plaster in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified |
| 36 | M&L for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed |
| 37 | M&L for applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty on ceiling after complete removal of existing treatment complete all as specified and directed |
| 38 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed |
| 39 | M&L for 75mm thick PCC 1:3:6 type C1 (Using 20mm graded stone aggregate) as in plinth protection/path laid in panels, finish the top surfaces even and smooth complete including filling the joints with mastic compound all as specified and directed |
| 40 | M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in path finish the top surfaces even and rough to receive top layer complete all as specified and directed |
| 41 | S&F for chequered cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry over and including 20 mm thick screed bed in CM(1:6), etc complete all as specified and as directed. |
| 42 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 43 | M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm) including making drainage opening wherever required complete |
| 44 | M&L for preparation of newly plastered or concrete surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of synthetic enamel paint over a coat of primer complete all as specified and as directed by Engr-in-Charge |
| 45 | Taking down chowkhats or frames area n. exc 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed |
| 46 | Taking down Chowkats exc 1.5 Sqm but n. exc 4 Sqm each with shutters (Without taking off shutters from the frame) complete all as specified and directed |
| 47 | Taking down shutter of any description n. exc 1 Sqm each complete all as specified and directed |
| 48 | Taking down shutter of any description exc 1 Sqm but n. exc 2 sqm each complete all as specified and directed |
| 49 | Taking down shutter of any description n. exc 1 Sqm each and refixing in the same opening including resecuring or easing of door shutters for easy closing/ opening, end tightening of butt hinges in position, adjustment of butt hinges in position, adjustment of existing aluminium mongry complete all as specified and directed |
| 50 | Taking down shutter of any description exc 1 Sqm but n. exc 2 sqm each and refixing in the same opening including resecuring or easing of door shutters for easy closing/ opening, end tightening of butt hinges in position, adjustment of butt hinges in position, adjustment of existing aluminium mongrycomplete all as specified and directed |
| 51 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm both side prelam PVC sheet and edges will be painted to match with the prelam sheet reinforced with MS square tube in opening incl necessary fixing arrangements as per specification and drawing complete all as specified and directed |
| 52 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC sheet for top rail, lock rail and bottom rail on either side as gap insert for top rails, bottom rail, panelling of both side prelam PVC sheet to be fitting in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement in the frame at site as per specification and drawing |
| 53 | S&F for 2nd class hard wood (SAL) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed |
| 54 | M & L for 1:3:6 type C1 (using 20mm graded aggregate stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed |
| 55 | S&F 30mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type both sides complete all as specified and directed.Make : Green/Century ply |
| 56 | S&F 30mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkhats complete all as specified |
| 57 | S&F 30mm thick 2nd class hard wood factory made glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified |
| 58 | S&F 100mm size stainless steel butt hinges medium weight complete all as specified |
| 59 | S&F 150mm aluminium, anodised, barrel tower bolts of extruded section all as specified |
| 60 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised all as specified |
| 61 | S & F 250mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed. |
| 62 | S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 140mm overall length of cover plate |
| 63 | S&F door seal bottom of width not less than 30 mm and length (ranges 500 mm to 1200 mm) suitable according to door shutter width to protect entry of insects efficiently, etc all as specified and as dierected. |
| 64 | M&L for applying two coats of synthetic enamel paint to new undecorated wooden surfaces over a coat of pink primer including preparation, over 10cm width or girth complete all as specified |
| 65 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 66 | M&L for anodised aluminium door shutters, aluminium section weighing not less than 1.55 Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, tower bolts, anodised aluminium snap beading screws etc complete all as specifiedNote : Supply only floor spring, glass, SS friction hinges, particle board, wire gauze will be measured seperately |
| 67 | M&L for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified complete all as specifiedNote : Supply only glass, particle board, wire gauze will be measured seperately |
| 68 | M&L for anodised aluminium window and ventilator shutters, side hung/sliding type without sash bars, aluminium sections weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays/Imax hinges 01 No, hinges type B-21 100mm long 02 Nos suitable handle 01 No per shutter or as required etc complete all as specified Note : Supply only glass, particle board, wire gauze will be measured and paid seperately |
| 69 | S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around theopening, all complete as per requirement and direction of Engineer-in-charge |
| 70 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone or steel/ aluminium frame concrete or brick surrounds, glazed complete all as specified and as directed |
| 71 | S&F figured glass, pin head type sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter not exc 0.5 Sqm in each pane complete all as specified and as directed |
| 72 | S&F sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter not exc 0.5 Sqm in each pane complete all as specified and as directed |
| 73 | S&F sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter exc 0.5 Sqm in each pane complete all as specified and as directed |
| 74 | S&F sheet glass 5.5mm thick ordinary quality and glazing with aluminium glazing clip in aluminium door/window/ventilator shutter not exc 0.5 Sqm in each pane complete all as specified and as directed |
| 75 | S&F 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work complete all as specified |
| 76 | S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples all as specified and directed |
| 77 | M&L in repairs to Aluminium composite panel sheet of 3.0mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30.0micron fixed over frame of aluminium tabular section 50x25mmx 2.0mm thick, having panels not exc 1200x1200mm with necessary silicon filling, in approved pattern as in column, beam, wall at any height with necessary scafoldings etc complete as specified and as directed. |
| 78 | S&F in repair aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples all as specified and directed |
| 79 | S&F in repair stainless steel IMAX hinges for aluminium window shutters complete all as specified and directed |
| 80 | S&F in repair vertical blinds for windows/ doors hanging by one end from a track with hand drawn control mechanism, threaded connection type, solid pattern, fixtures and fittings included, slats can be rotated 90 degree to allow light to pass through or to fold up on one side of a window/door complete all as specified |
| 81 | S&F in repair 600x450x6mm thick looking mirror bevelled edge of selected quality glass fixed with stainless steel glass fastner complete all as specified |
| 82 | S& F in repairs, 25 mm dia Stainless steel curtain rods with fancy type curtain brackets, stops, rollers as per the site requirements etc complete all as specified and as directed. |
| 83 | S&F in repairs door closer hydraulically regulated aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed. |
| 84 | S&F in repairs Stainless Steel EGF combo with lock heavy duty automatic floor spring (80Kg) load, with necessary fitting, etc all as specified and as dierected. Make : Godrej or equivalent as approved by GE. |
| 85 | S&F in repair vitreous china wash down water closed pan (Pedestal pattern) white, including connection to drain (or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) complete all as specified and directed. |
| 86 | S&F in repair plastic water closet seat cover, white, closed pattern with flat bottom including mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 87 | S & F in repairs vitreous china wash down single piece WC Rimless Bowl with Cistern for Coupled WC with UF Soft Close Slim Seat Cover, Hinges, Dual Flush Cistern Fitting, Conversion Bend, Fixing Accessories and Accessories Set, with 'S' or 'P' trap and other connecting items approved brand including fix with white cement complete all as specified and directed.Make-Jaquar Cat Pt No.OPS-WHT-15753NS250UFSMZ or equivalent in Parryware/Cera/Prayag |
| 88 | S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action push type with inlet ball valve and float including flush pipe long 32mm dia, ball valve, handle, bracket etc complete all as specified and directed |
| 89 | S&F in repair vitreous china counter wash hand basin oval shape of size 550x400mm including brackets, 32 mm CP waste coupling, chain and plug, waste fittings all necessary inlet and out let connections complete all as specified |
| 90 | S&F 15mm dia brass CP urinal spreader complete all as specified |
| 91 | S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified and directed. |
| 92 | S&F in repairs 32 mm dia PVC flush pipe of polyethylene of low or high density for WHB, sink, urinal complete all as specified and directed |
| 93 | S&F in repair chromium plated brass shower roses with or without swivel joints square type 125mm size including shower arm complete all as specified and directed |
| 94 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed |
| 95 | S&F in repair Toilet paper holder .Make :Jaquar Code ACN-1153N or equivalent model in Parryware / Prayag / Gem |
| 96 | S&F in repair towel ring round Make : Jaquar AQN -7721 or equivalent model in Parryware / Prayag / Gem |
| 97 | S&F in repair tubular towel rail, brass, chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and as directedMake : Jaquar Cat Part No AQN-7711 |
| 98 | S&F in repair chromium plated soap dish of size 120x80mm, fixed to plugs with chromium plated brass screws complete all as specified |
| 99 | S&F in repair 15mm dia cast copper alloy chromium plated long body bib tap fancy type with wall flange complete all as specified |
| 100 | S&F in repair bib tap, brass, 15mm dia, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and as directedMake : Jaquar Cat Part No CON-107KN |
| 101 | S&F in repair two way bib cock, 15mm dia cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified |
| 102 | S&F in repair 15mm dia cast copper alloy, chromium plated pillar tap long body swan neck type with fly nut capstan head screwed for 15mm bore dia of pipe complete all as specified |
| 103 | S&F in repair angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for unions complete all as specified and as directedMake : Jaquar Cat Part No CON-053KN |
| 104 | S&F in repair 15mm concealed type angle cock cast copper alloy, fancy type, chromium plated with long shunk and cup high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified |
| 105 | S&F in repair WHB mixer, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long shank with central hole screwed down, screwed both ends for iron pipe or for unions complete all as specified and as directed Make : Jaquar Cat Part No CON-167KNB |
| 106 | S & F in repairs for wall mixer 3-in-1 system with provision for both hand shower and over head shower composite with 115 mm long bend pipe connecting legs & wall flanges Mixer complete all as specified and as directed.Make: Prayag Cat No PIS-80H or Equivalent approved), hand shower including 1.5 mtr flexible tube with hook Cat No BHS-99 of Prayag or Equivalent, and over head showerwith arm and flange (300mm) of cat No BS-69 of Prayag or Equivalent in Jaquar. |
| 107 | S&F factory made single extruded WPC (wood polymer composite) soild door/window/ceosetory windows and other frames/ chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750Kg/Cum, screw withdrawl strength of 2200N (face) and 1100N (edge), minimum compressive strength of 58 N/Sqmm, modules of elasticity 900 N/Sqmm and resistance to spread of flame of class 'A' category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (MS hold fast/lugs or SS dash fasteners shall be paid for separately)Note : for WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 108 | S&F factory made single extruded WPC (wood polymer composite) soild door/window/ceosetory windows and other frames/ chowkhat of size 65 x125mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750Kg/Cum, screw withdrawl strength of 2200N (face) and 1100N (edge), minimum compressive strength of 58 N/Sqmm, modules of elasticity 900 N/Sqmm and resistance to spread of flame of class 'A' category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (MS hold fast/lugs or SS dash fasteners shall be paid for separately)Note : for WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 109 | S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws incl in this item) |
| 110 | S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified |
| 111 | S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mmx420mm bowl size 410mmx330mmx160mm complete all as specified |
| 112 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed |
| 113 | Supply and fix for PVC insulation panels 10 mm thick with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. As per specification and drawing including dismantling ceiling and wall boards or insulation board any thickness including cover fillets etc, all as specified and directed. |
| 114 | M&L in repairs to 12 mm thick WPC (Wood-Plastic Composite) louvers Panel boards as in Wall panelling work fixed over frame work using suitable aluminium profile sections of size 50mmx25mmx2mm thick and fixed with suitable screws / fasteners as per the site requirents etc complete all as specified and directed.Note: Design and Pattern will be finilized by the Engr In charge. |
| 115 | S&F Stainless steel 25mm thick glass door full handle 14 inches length with necessary fitting, etc all as specified and as directed.Make Prayag Cat No SH25-14P-SS |
| 116 | S&F in repair 100mm size, 4 levers brass mortice lock, vertical type complete all as specified |
| 117 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons, riser of steps, skirting, dado etc laid in any mortar complete all as specified. |
| 118 | M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms,floor, walls and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and polishing including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 119 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed |
| 120 | M&L for seamless designed gypsum board false ceiling 12mm thick including for any sunk or raised moulding with 25mm long self drilling/ tapping screws having philips head with joining compound and 48mm wide fiber tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flange of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm suspended from soffit at approx 900mm c/c with GI cleats and steel expansion fasteners with and incl ceiling section ( not exc 1.2m length) of 0.55mm thick having kurled web of 50mm an flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting across the intermediate channel at 457mm c/c incl hangers 6mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete and finally applying two coats of oil bound distember with roller finish over a coat of chalk whiting primer cmplete all as specified and directed |
| 121 | M&L anodized aluminium snap grid framework incl 4 mm thick non asbestos fibre cement building boards 600x600mm incl two coats OBD and preparation of surfaces over board inserted to framework with screws with hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysSep 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender