Tender For Work Of Renovation And Construction Of Boundary Wall Of Sidhauli Inspection Building In Sitapur District (Lot No. 01)
Tender Value
1.65 Crore
Estimated cost
Bid Submission
31 Aug 2026
8 days left
EMD
3.31 Lakhs
Bank guarantee accepted
Document Fee
4764
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sitapur → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Work Of Renovation And Construction Of Boundary Wall Of Sidhauli Inspection Building In Sitapur District (Lot No. 01)
BOQ
| Sl. No. | Item Description |
| 1 | Cleaning of thick jungle and thorney bushes without uprooting etc all complete. |
| 2 | Dag belling 7.50 cm Deep including Cost of all Material, labour and T&P etc required for proper completion of work. |
| 3 | Earth work in foundation of masonary work for building work including lead upto 30m. & lift upto 1.50m and its disposal & back filling. |
| 4 | E/W in cutting or filling along the boundary wall including Cost of all Material, labour and T&P etc required for proper completion of work. |
| 5 | Construction of Subgrade and Earthen shoulder with approved material obtained from borrow pits with all lift and leads,transporting to site spreading grading to require slope and compacted to meet requirement of table 300.2 with lead up to 1000 m as per MORD technical specification clause 303.1 |
| 6 | Supplying and laying brick ballast .including cost of all material, labour and T&P etc. required for proper completion of work as per direction of Engineer in -charge. |
| 7 | Edging with straight over burnt laid by lenghtwise including excavation, refiliing cosilidation with a hand packing and spreading nearly sur plus earth with in a lead of 50 mtr |
| 8 | Laying over burnt Brick soling layer on prepared sub grade with brick on end edging according to lines, graded and cross section shown on the drawing filling joints with sand and earth , spreading 25 mm thick layer of earth over brick soling, watering and rolling the same with three wheel road roller 80-100 KN as per MORTH. |
| 9 | Providing and Laying of interlocking concrete, block pavement having thickness 60 mm per as per drawing and MORD technical specification Clause 1504 including Cost of all Material, labour and T&P etc required for proper completion of work. as directed by engineer in charge. |
| 10 | P.C.C. work in 1:4:8 in Foundation including all cost of material,labour T&P etc. for complete work. |
| 11 | P.C.C. work in 1:3:6 in Foundation including all cost of material,labour T&P etc. for complete work. |
| 12 | Dismantling Cement Concrete including disposal of refuse as per directed by engineer in charge with in a distance of 60 mtr Cost of all Material, labour and T&P etc required for proper completion of work. |
| 13 | Dismantling Brick Work including disposal of refuse as per directed by engineer in charge with in a distance of 60 mtr Cost of all Material, labour and T&P etc required for proper completion of work. |
| 14 | Dismantling existing Plaster including disposal of refuse as per directed by engineer in charge with in a distance of 60 mtr Cost of all Material, labour and T&P etc required for proper completion of work. |
| 15 | Supplying and fixing tor steel T.M.T. bar at work site including Cost of all Material, labour and T&P etc required for proper completion of work.required for proper completion of work. |
| 16 | Centring and shuttering of R.C.C. work including cost of all material, labour and T&P etc. required for proper completion of work as per direction of Engineer in -charge. |
| 17 | Providing and laying of R.C.C. work in 1:1.5:3 with cement, coarse sand and 20 mm crushed stone grit including cost of all material, labour and T&P etc. required for proper |
| 18 | M 100 Brick work in 1:5 cement mortor including cost of all material, labour and T&P etc. required for proper completion of work as per direction of Engineer in -charge. |
| 19 | M150 Brick work in 1:4 cement mortor including cost of all material, labour and T&P etc. required for proper completion of work as per direction of Engineer in -charge. |
| 20 | C.C. work in 1:2:4 for coping & Floor work including all cost of material,labour T&P etc. for complete work. |
| 21 | Providing & Laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 course sand (zone-III) : 4 graded stone aggregate 12.5 mm nomonal size) |
| 22 | 10 to 15 mm thick Plaster of (1:6) cement mortar including Cost of all Material, labour and T&P etc required for proper completion of work. |
| 23 | 10 to 15 mm thick Plaster of (1:4) cement mortar including Cost of all Material, labour and T&P etc required for proper completion of work. |
| 24 | Finishing walls with Premium Acrylic Smooth exterior (weather proof) paint with Silicone additives of required shade including Cost of all Material, labour and T&P etc required for proper completion of work. |
| 25 | Steel work welded in built up section / framed work including cuting, hosting, fixing, in position and applying a priming coat of approved steel primer using structural steel etc as required in gratings, frames, guard bar, ladder, railing, brackets, gates and similiar works etc all complete. |
| 26 | Painting or varnishing on iron work in small areas or new wood work with one coat of ready mixed priming paints and two coat of approved superior quality ready mixed paint of clear synthetic varnish including supply of all material, labour, and T&P etc required for proper completion of work. |
| 27 | Fabrication & Supply of angle iron frame 40x40x6 mm iron bracing including supply of all material, labour, and T&P etc required for proper completion of work. |
| 28 | Providing barbed iron wire fencing including fixing it to post after stretching it including Labour and T&P etc. required for proper completion of the work also excluding supply of posts. |
| 29 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 30 | Finishing wall with oil BOUND distemper (interior) on new surface including Cost of all Material, labour and T&P etc required for proper completion of work. |
| 31 | Providing and fixing ISI Marked Flush Door shutters conforming to IS :2202 (Part -I) non-decorative type core of block board construction with frame of 1St class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters .35 mm thick including ISI marked Stainless Steel butt hings with necessary. |
| 32 | Providing and fixing wire gauge shutters using stainless steel wire gauge (grade-304) aperture 1.4 mm and 0.50 dia wire,for doors,windows and clerestory windows,:35 mm thick shutters ,of required size UP teak wood second class teak wood. |
| 33 | Providing and fixing glazing in aluminium door for toilet room shutters and partitions etc. with EPDM rubber / neoprene gasket etc. Complete as per the architectural drawing and the direction of engineer in charge.(weight not less then 20kg/sqm) |
| 34 | Painting or varnishing on iron work in small areas or new wood work with one coat of ready mixed priming paints and two coat of approved superior quality ready mixed paint of clear synthetic varnish including supply of all material, labour, and T&P etc required for proper completion of work. paint to be used should conferm to the I.S.I No. 103-1950 |
| 35 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 36 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :9.97.1 300x10 mm |
| 37 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper |
| 38 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 9.95.1 125x75x4 mm |
| 39 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, includingpriming coat of approved steel primer, but excluding the cost of other fittings, glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) including glass pane. |
| 40 | P&L 40MM thick neat cement flooring including Cost of all Material, labour and T&P etc required for proper completion of work. |
| 41 | Providing and Laying Vitrified tiles in different sizes, (thickness to be specified by the manufacturer )with water absorption, less than .08 percentage and confirming to ISO 15622 of approved make in all colours and shades laid on 20 mm thick cement motor 1:4 ( 1 cement:4 Coarse Sand) , joining with grey cement slurry at the rate 3.3 kg per square metre, including grouting the joints with white cement and matching pigments, etc size of tile 600 X600 mm |
| 42 | Providing & Laying ceremic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer ) of Ist quality confirming to I.S 15622 of approved make in colour such as white,lvory,gray,fume red brown,laid on 20mm thick cement mortor 1:4( 1 cement:4 Coarse Sand)joining with grey cement slurry @ 3.3kg per sqm.including pointing the joints with white cement and matching pigment etc. comlete. |
| 43 | P/F CPVC pipes complete with fittings & clamps, including cutting and making good the surface of walls etc. complete (Internal Works) |
| 44 | P/F concealed CPVC pipes complete with fittings & refilling etc. complete (concealed Works) |
| 45 | P/F in position best India make proper copper alloy gate valve and check valve (Class-I) IS-778-1980 with iron wheel head etc. complete. 20MM dia. |
| 46 | P/F C.P. brass angle valve for cistern, wash basin, Gyger etc. 15 mm nominal hole size including cost of all material, labour, T&P etc. |
| 47 | P/F chromium plated bib cock, complete with all materials. |
| 48 | Fixing C.P. brass soap dish with C.P. brass brackets fixed to wooden plugs, plastic sleeves with C.P. brass screws. |
| 49 | P/F Indian type white glazed earthen ware 1st quality IS1 marked W.C. pan size 580 mm Indian make of approved quality including cost of all material. |
| 50 | P/F European type white glazed earthen ware W.C. pan (Indian make) of approved 1st quality ISI marked Bakelite seat cover & lid with C.P. brass hinges and rubber buffers. |
| 51 | P/F wash basin with single hole/number of holes for pillar tap with C.I. or M.S. brackets painted white including cutting hole & making good the same but excluding fittings. 630X450 MM |
| 52 | P/F pedestal for wash basin complete recessed at the back for the reception of pipes and fittings. |
| 53 | P/F mirror of following size of approved make with teak wood moulded frame and 6 mm thick hardboard backing including cost of all material, labour, T&P etc. |
| 54 | Polyethylene water storage tank with cover and suitable locking arrangement |
| 55 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm |
| 56 | White vitreous china clay half stall urinal flat back 580x380x350 mm or angle back 450x375x350 mm with waste fittings as per IS:255 |
| 57 | Providing and fixing square mounth sw 150x100mm size p type trap class sp-1 complete.direction of engineer in charge |
| 58 | Wiring point for light 1.5 sq.mm PVC insulated single core COPPER cable in heavy gauge PVC conduit concealed in the wall complete with 8 SWG G.I. earth continuity wire and I5 A piano type switch etc. complete in all respects |
| 59 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 60 | Wiring point for fan 1.5 sq.mm PVC insulated single core COPPER cable in heavy gauge PVC conduit concealed in the wall complete with 8 SWG G.I. earth continuity wire and I5 A piano type switch etc. complete in all respects |
| 61 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required |
| 62 | wiring for power plug with 2x4 sq. Mm FRLS PVC insulated copper conductor single core in surface/ recesed steel conduit alongwith 1 no. 4 sq. mm FRLS PVC inulated copper coductor single core cable for loop esrting as required. |
| 63 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 &15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 64 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 65 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. b)4 X 10 sq. mm + 2 X 6 sq. mm earth wire. |
| 66 | wiring for circuit/submain alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core in surface/ recesed medium class PVC conduit as reuired. 2 no. 16 sq. mm + 1no. 6 sq. mm earth wire |
| 67 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. A) 100 A, 16 KA,TPMCCB |
| 68 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without 8 way (4 + 24), Double door MCB/RCCB/Isolator) |
| 69 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 70 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole |
| 71 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/ coke and salt as required. |
| 72 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/recessed conduit/sub main wiring/cable as required. |
| 73 | Providing and fixing stainless Steel A ISI 304 Kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fitting and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board |
| 74 | Smooth finishing of the exposed surface of R C C work with 6 mm thick cement mortar 1:3 (1 Cement :3 fine sand) |
| 75 | Providing and displaying of Areca Palm having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and ealthy with lush green foliage in 35 cm size of Bucket type cement pots & as per direction of the officer-in-charge. |
| 76 | Providing and stacking of Tabernaemontana divaricata (Chandni double) of height 90-105 cm., bushy in big size HDPE bag as per direction of the officer-in-charge. |
| 77 | Providing and stacking of Hibiscus rosasinensis of height 90-105 cm., bushy in big size HDPE bag as per direction of the officer-in-charge. |
| 78 | Providing and Displaying Ficus reginold well developed fresh & healthy foliage 60 to 75 cm spread 105 to 120 cm ht., Bushy in 35 cm Cement Pot as per direction of the officer-in-charge. |
| 79 | Grassing with the selection no.1 grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for seprately) |
| 80 | Supplying, installation, testing & commissioning of smoke detector Each 1153.00 with builtin LED and mounting base complete with all connections etc. as required |
| 81 | Supply and erection of steel tubular pole 9.0 meters long designated 410 SP-29 in 1:3:6 cement concrete foundation including excavation, back filling etc. complete in all respects. |
| 82 | Supply and fixing of LED Street Light fitting with mandatary driver set having die cast aluminium body with toughend glass UV stablized PC cover and lanses suitable for 160 watt to 175 watt and confirming to IP 66, and IK07 and above protection having company logo Engraved complete in all respect including labour. |
| 83 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. |
| 84 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.(150 mm dia) |
| 85 | Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 86 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well screen(RMS) pipes with ribs, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.150 mm nominal size dia. |
| 87 | Supply/Fixing Starter 3 phase 415 volt of Submersible Pump. |
| 88 | Installing of pumping set with all L/M and T&P |
| 89 | Provide & fixing C.I sluice valve. 100mm nominal class 1 |
| 90 | Provide & fixing M.S clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part-1) including necessary bolt & Nuts of required size complete. 200 mm clamp |
| 91 | Supplying,filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts all complete as per direction of Engineer- in - charge. |
| 92 | Providing & fixing bali plug/ bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS; 2800 (part1) 150 mm dia |
| 93 | Providing & fixing G.I pipes complite with G.I fitting including trenchingand refilling etc. Submersible to OHT. (80 mm dia nominal bore) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender