Tender For Provn Of Toilet Block (03 X Toilet, 03 X Bathroom And 01 X Whb) Near Bldg No P-195 Otm Accn (Single Jcos Living) Of No 02 Inf Bn And Provision Of 01 Combined Septic Tank For Oc Office, Office Complex And Duty Clerk Of 659 Tpt Coy Asc Type
Tender Value
8.46 Lakhs
Estimated cost
Bid Submission
31 Aug 2026
7 days left
EMD
16920
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udaipur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Toilet Block (03 X Toilet, 03 X Bathroom And 01 X Whb) Near Bldg No P-195 Otm Accn (Single Jcos Living) Of No 02 Inf Bn And Provision Of 01 Combined Septic Tank For Oc Office, Office Complex And Duty Clerk Of 659 Tpt Coy Asc Type ‘A At Sajjan Line Area Of Udaipur Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m : All kinds of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 cement : 4 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA) |
| 4 | Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand) |
| 5 | Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS :12894, in super structure above plinth upto floor V level:Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 6 | Material & Labour for Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed. |
| 7 | Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 4 graded stone aggregate 20 mm nominal size (Recycled Concrete Aggregate (RCA) upto 25%)) |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 4 graded stone aggregate 20 mm nominal size including Recycled Concrete Aggregate (RCA) upto 25%) |
| 9 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 6 graded stone aggregate 20 mm nominal size Recycled Concrete Aggregate (RCA) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral staircases above plinth level up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand incuding manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 20%: 3 graded stone aggregate 20 mm nominal size including Recycled Concrete Aggregate (RCA) upto 20%) |
| 13 | Providing and fixing Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level :Mild steel and Medium Tensile steel bars |
| 14 | Providing and laying of 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) on roof concrete surfaces with water proofing compound as per manufacturer's instructions, finished the surface even and smooth. |
| 15 | Providing and fixing Ist quality ceramic glazed wall tiles of size 600x300 conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 16 | Providing and laying Ceramic glazed floor tiles of size 400x400 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 17 | Providing and fixing Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels |
| 18 | Providing and fixing factory made frame size 45 x 85 mm single extruded WPC (Wood Polymer Composite) solid door/window/ Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (SuspensionGrade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 19 | Providing and fixing factory made 30 mm thick single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 20 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm |
| 21 | Providing and fixing aluminium handles for wooden door ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 22 | Providing and fixing bright /matt finished Stainless Steel handles for bathroom doors of approved quality & make with necessary screws etc all complete: 125 mm |
| 23 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 24 | Providing and fixing Frosted glass sheet of nominal thickness 4 mm (weighing not less than 10 kg/sqm) |
| 25 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.:Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 26 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 27 | Providing and fixing in repairs counter below wash basin with waste coupling, C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. |
| 28 | Providing and fixing in repairs water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 29 | Providing and fixing in repairs white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 30 | Providing and Fixing in repairs health fucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 Mtr long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 31 | Providing and fixing in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge. |
| 32 | Providing and fixing 300mm long Stainless Steel hat pegs of 6 Nos peg set of good quality. |
| 33 | Providing and fixing in repair 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 34 | Providing and fixing in repair 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 35 | Providing and fixing in repair C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter |
| 36 | Providing and fixing in repair C.P. brass angle valve for washbasin, urinal, flushing cistern, geyser points etc. of approved quality conforming to IS:8931 : 15 mm nominal bore |
| 37 | Providing and fixing in repair uplasticised PVC connection pipe 45 cm length with brass unions :15 mm nominal bore |
| 38 | Providing and fixing in repairs Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittings |
| 39 | Providing and fixing in repair PTMT grating of approved quality and colour: 100 mm nominal dia |
| 40 | Providing and fixing in repair PTMT grating of approved quality and colour : 125 mm nominal dia with 25 mm waste hole |
| 41 | Providing and fixing in repair PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 42 | Providing and fixing 75mm dia PVC (SWR) floor trap, with grating including jointing with solvant cement. |
| 43 | Material & Labour for Green Marble 25 cm x 25 cm x 12-15 mm thick machine cut prepolished embedded for bathroom wall as corner shelf round shape all as specified and directed. |
| 44 | Providing and fixing in repairs C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931:15 mm nominal bore |
| 45 | Providing and fixing in repair C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore |
| 46 | Providing and fixing PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement |
| 47 | Providing and fixing in repair rotational molded polyethylene water storage tanks white tripple layered (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position all as specified and directed by Engr-in-charge. |
| 48 | Providing and fixing in repair PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball: 20 mm nominal bore, 120 mm long, weighing not less than 198 gms |
| 49 | Providing and fixing in repair gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore vertical |
| 50 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc:Exposed on wall 25 mm dia nominal bore |
| 51 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge:Internal work - Exposed on wall 15 mm nominal dia Pipes |
| 52 | Providing and fixing on wall face/laid in trenches or floor unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes: 110 mm diameter |
| 53 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion : 110 mm bend |
| 54 | Providing and fixing on wall face/laid in trenches or floor unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes: 75 mm diameter |
| 55 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion: 75 mm bend |
| 56 | Providing and fixing of PVC (SWR) vent cowl 110mm dia complete. |
| 57 | Providing and fixing of 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) on brick/stone masonry or concrete surfaces of external walls, finished the surface even and smooth. |
| 58 | Providing and applying of finishing for external walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 59 | Providing and fixing of 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) on brick/stone masonry or concrete surfaces of internal walls, finished the surface even and smooth. |
| 60 | Providing and applying of distempering for internal walls with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 61 | Providing and fixing of 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) on brick/stone masonry or concrete surfaces of ceiling, finished the surface even and smooth. |
| 62 | Providing and applying of white washing for ceiling with lime to give an even shade : New work (three or more coats) |
| 63 | Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS :1536 :150 mm dia pipe |
| 64 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, suitable GI box for modular switch/Socket/Regulator etc, modular plateand earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required including junction box all as sepcified and directed |
| 65 | One light point controlled by one switch with cables 1.5 sqmm size. |
| 66 | One fan/ exhaust fan point controlled by one switch with cables 1.5 sqmm size. |
| 67 | One 3 pin socket outlet, 5 amps on the same board with other switches, with cables 1.5 sqmm size. |
| 68 | One 3 Pin socket oulet 5Amps on indepndent, with cables 1.5 Sqmm size. |
| 69 | One 3 Pin 15A pin socket oulet 15Amps on indepndent board or for geyser point with cables 2.5 Sqmm size |
| 70 | Supplying and fixing 5/6 Amp modular piano type switch on the existing switch box/ cover including connections etc. as required. |
| 71 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 72 | Supplying and fixing 5/6 Amp modular type socket on the existing switch box/ cover including connections etc. as required. |
| 73 | Supplying and fixing 15/16 Amp modular piano type switch on the existing switch box/ cover including connections etc. as required. |
| 74 | Supplying and fixing 15/16 Amp modular type socket on the existing switch box/ cover including connections etc. as required. |
| 75 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 76 | Supplying and fixing 5/6 Amp modular piano type 2 way switch on the existing switch box/ cover including connections etc. as required. |
| 77 | LED Down lighter (SMD Type) (System lumen Unit Rate efficacy ≥ 105 < 120 lm/Watt ) Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -50C to 400C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim 18 Watt |
| 78 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. |
| 79 | S&F LED lamp 9W system lumen (NOM) 600 with all accessories all as specified and directed by Engr-in-Charge. |
| 80 | Supplying and fixing 8 Way double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 81 | Supplying and fixing 40A, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 82 | Supplying and fixing 63A rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 83 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of single poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 84 | Installation, Testing and Commissioning of 200mm exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 85 | Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I 2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade, for protection of earth lead complete all as specified and directed. |
| 86 | S&F Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x2.5sqmm earth wire FRLS PVC insulated copper conductor, single core cable in surface/recessed as required.Note : Two run of 2.5 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM. |
| 87 | S&F Submain wiring alongwith earth wire with the following sizes of 2x4.0 sqmm + 1x4.0 sqmm earth wire FRLS PVC insulated copper conductor, single core cable in surface/recessed as required.Note : Two run of 4.0 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM. |
| 88 | Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 89 | Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. |
| 90 | watt LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 48 DELHI SCHEDULE OF RATES (E&M)-202561000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),SDCM (Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). |
| 91 | Excavating in trenchs not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation and getting out in in soft loose soil complete all as specified and directed. |
| 92 | M&L For Returning, filling in, including spreading, levelling, watering and well ramming in layersnot exc 25 cm. |
| 93 | Excavating in trenchs not exceeding 1.5m wide and exceeding 1.5m in depth for foundation and getting out in in soft loose soil complete all as specified and directed. |
| 94 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point |
| 95 | M&L For Cement concrete type D2 1:4:8 in foundations,filling and mass concrete |
| 96 | M&L for reinforced cement concrete M-25 (design mix) using 20mm graded stone aggregate in slab complete all as specified and directed. |
| 97 | M&L for TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mm dia all as specified. |
| 98 | M&L for TMT bars 8mm dia and over upto and including 10mm dia in stirrups cut to length bent to shape all as specified. |
| 99 | M&L for formwork foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter |
| 100 | M&L For Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in Old size bricks in cement mortar 1:4 |
| 101 | M&L for rendering 15mm thick on brick work or concrete surfaces in cement mortar (1:4) finished even and smooth w/o using extra cement complete all as specified & directed |
| 102 | Providing and laying 200 mm dia Dwc sewage pipe cement concrete 1:5:10 (1 cement : 5 coarse sand 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : |
| 103 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality |
| 104 | providing and fixing soil waste pipe and vent pipe 100 mm dia centrifugally cast iron soket &spigot (s&s) pipe as per is 3989 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysSep 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender