Tender For Repair Maintenance Of External Water Supply Along With Connected Works Of Pumping, Distribution System At Zone Iii And Iv Area Under Ge Dinjan
Tender Value
48 Lakhs
Estimated cost
Bid Submission
03 Sep 2026
7 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair Maintenance Of External Water Supply Along With Connected Works Of Pumping, Distribution System At Zone Iii And Iv Area Under Ge Dinjan
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete unreinforced, in ground floor or pavings below or above ground level from foundation of pump sets including removal of debris from site to outside of MoD land complete all as specified and as directed . |
| 2 | M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregates as in foundation, sub base or mass concrete complete all as specified and as directed. |
| 3 | Labour for Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out electric motor 10 HP to 15 HP capacities from base plate of pump set after opening the nuts, bolts etc and transporting the motor to workshop for repair and back, reinstalling after repair including testing complete all as specified and as directed.NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor. |
| 4 | Labour for opening the electric induction motor 10 HP to 15 HP capacity including taking down/out the burnt winding wire , cleaning the slots, rewinding the motor with super enamalled copper winding wire of existing gauge ,weight etc. including all other insulating material to make it functional complete all as specified and as directed .Note:- Copper winding wire of approprioate guage will be measured in supply only complete all as specified and directed. |
| 5 | Supplying and Fixing in replacement of Motor Terminal Box upto 15 HP motor capacity complete all as specified and directed. |
| 6 | Supplying and Fixing in replacement of Motor Terminal Connection Plate upto 15 HP motor capacity complete all as specified and directed. |
| 7 | Supplying and Fixing in replacement of CI Sleeve on Bearing Housing upto 15 HP motorcapacity complete all as specified and directed. |
| 8 | Supply and Fixing in replacement of Motor Cooling Fan as per site requirement for any size of motor made of PVC/ Aluminium complete all as specified and directed. |
| 9 | Labour for Disconnecting and De-coupling the Centrifugal pump 10 HP to15 HP capacity from foundation after opening /cutting the rusted nuts, bolts etc including transporting the pump to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor. |
| 10 | Opening the centrifugal pump 10 HP to15 HP capacity, repairing the same by replacing the unserviceable spare parts including machining work and re-assembling the same in original position complete all as specified and as directed. |
| 11 | Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out monoblock pump set capacity 5 HP to 7.5 HP from foundation/base plate of pump set after opening the nuts, bolts etc and transporting the pump to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed .NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor. |
| 12 | Opening the monoblock motor and pump capacity 5 HP to7.5 HP , taking down/out the burnt winding wire and cleaning the slots including rewinding the monoblock motor with super enamelled copper winding wire of existing gauge ,weight etc. and repairing the pump by replacing the unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed.Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely |
| 13 | Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out monoblock pump set capacity 3 HP from foundation/base plate of pump set after opening the nuts, bolts etc and transporting the pump to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed.NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor. |
| 14 | Opening the monoblock motor and pump capacity 3 HP, taking down/out the burnt winding wire and cleaning the slots including rewinding the monoblock motor with super enamelled copper winding wire of existing gauge ,weight etc. and repairing the pump by replacing the unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed.Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely |
| 15 | Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out monoblock pump set capacity upto 2 HP from foundation/base plate of pump set after opening the nuts, bolts etc and transporting the pump to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed.NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor. |
| 16 | Opening the monoblock motor and pump capacity upto 2 HP , taking down/out the burnt winding wire and cleaning the slots including rewinding the monoblock motor with super enamelled copper winding wire of existing gauge ,weight etc. and repairing the pump by replacing the unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed.Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely |
| 17 | Supply & Fixing 0.5 HP pressure pump, suction size 25mm ,delivery size 25mm, 06 metre minimum head, single phase, 220 Volts,50Hz including automatic switches ON & OFF, when tap is used incl electric connection from nearst DB complete all as specified and as directed. |
| 18 | Supplying and assembling super enamelled copper winding wire of appropriate gauge suitable upto 25 HP capacity of centrifugal, monoblock, inducation and submersible motors complete all as specified and directed. |
| 19 | Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 5-20 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed. |
| 20 | Supply and Fixing in replacement MS base channel of size as exists including cutting, welding and making hole including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 21 | Supply and Fixing in replacement of MS foundation bolts with nuts and washers, size 20mm dia , 250 mm long complete all as specified and as directed. |
| 22 | Supply and fixing in replacement 4.00 sqmm, single core FRLS PVC insulated industrial grade copper conductor wire of following size, 1100 volts complete all as specified and as directed. |
| 23 | Supply and fixing in replacement 6.00 sqmm, single core FRLS PVC insulated industrial grade copper conductor wire of following size, 1100 volts complete all as specified and as directed. |
| 24 | Supply and fixing in replacement PVC insulated FRLS round sheathed copper conductor wire of 2.5 Sqmm, 3 core, 1100 volts complete all as specified and as directed. |
| 25 | Supply and fixing in replacement moulded case circuit breakers (MCCB), 4 pole, 100 Amps with breaking capcity 16 KA , 415 volts, complete all as specified and as directed.Make:-L& T or equivalent in Legrand/ Siemens. |
| 26 | Supply and fixing in replacement of Submersible panel board MN 16 DOL starter type suitable upto 10 HP Make L&T or equivalent in BCH / SIEMENS |
| 27 | Supply and fixing in replacement of fully automatic star delta starter type with sheet metal encloser MN 25 FASD Make L&T or equivalent in BCH / SIEMENS complete all as specified and directed. |
| 28 | Disconneting of electrical connection from the panel board, and starter of submersible pumping set of any model / make size 10 HP to 25 HP capacity and removing the pipe line connection from discharge side and taking out submersible pump set along with column pipe from bore well with the help of chain pully block including transportation to Workshop and back after repair and lowering of same pumping bore well including replacement of rusted nuts bolts rubber gasket etc to make it fully functional, testing complete all as specified and directed. |
| 29 | Opening the submersible motor set of capacity 25.00 HP including taking down/out the burnt winding wire cleaning the slots, rewinding the motor with super enamelled copper winding wire of existing gauge, weight etc, repairing the same by replacing the unserviceable parts including machine/ lathe work and re-assembling the pump set in original position with required insulating material to make it fully functional complete all as specified and as directed. |
| 30 | All as per Srl Item No.29 above but capacity 20 HP complete all as specified and directed. |
| 31 | All as per Item Srl Item No.29 above but capacity 17.5 HP complete all as specified and directed. |
| 32 | All as per Item Srl Item No.29 above but capacity 15 HP complete all as specified and directed. |
| 33 | M&L in repair for submersible pump set capacity 15.0 to 25 HP capacity with as per existing parts of pump to achieve the specified/required RPM including taking out unserviceable parts and removing the pipe line connection from discharge side and taking out submersible pump set along with column pipe from bore well with the help of chain pully block including transportation to Workshop and back after repair and lowering of same pumping bore well including replacement of rusted nuts bolts rubber gasket etc to make it fully functional, testing complete all as specified and directed. |
| 34 | Material and labour for painting of submersible pump set of size 2 HP to 20 HP with two coat of synthetic enamelled paint over coat of red oxide primer comete all as specified and ad directed. |
| 35 | M&L for replacement of heavy duty GI nipple 300 mm long and 100 mm bore with flange welded on both ends complete all as specified and directed. |
| 36 | M&L for replacement of heavy duty GI nipple 300 mm long and 80 mm bore with flange welded on both ends complete all as specified and directed. |
| 37 | Supply and fixing water proof submersible cable of 6 sqmm 3 core copper conductor, PVC insulated 1100 volts grade, protected by means of metal clip alongwith the pump body and connected to pump motor through water tight sealing joints including taking out old unserviceable submersible cable complete all as specified and as directed of the following sizes:- (Make: finolex/ polycab/Havells) |
| 38 | All as per Srl Item No.37 above but size 10 sqmm 3 complete all as specified and directed. |
| 39 | Supply and fixing in replacement of GI Pipe column pipe heavy grade, 100 mm bore 3 mtrs long coupled with heavy grade suitable size of MS flanges 16mm thick duly welded on both sides as directed including necessary nut and bolts with washers & rubber packing required at site condition and lowered in to the bore well including taking out old unserviceable Column pipe complete all as specified and directed (length of each column pipe shall be 3 Mtrs) (Note : - taking out and Lowering of Submersible pump set shall be measured and paid under respective item) |
| 40 | Supply and fixing in replacement of GI Pipe column pipe heavy grade, 80 mm bore 3 mtrs long coupled with heavy grade suitable size of MS flanges 16mm thick duly welded on both sides as directed including necessary nut and bolts with washers & rubber packing required at site condition and lowered in to the bore well including taking out old unserviceable Column pipe complete all as specified and directed (length of each column pipe shall be 3 Mtrs) (Note : - taking out and Lowering of Submersible pump set shall be measured and paid under respective item) |
| 41 | Supply and fixing MS clamp in replacement of MS falt 100mm X 6mm with two Nos of MS nut & blots for upto 100mm dia column pipe complete all as specified and directed. |
| 42 | Opening the 3 HP induction motor of Air compressor, taking down/out the burnt winding wire and cleaning the slots including rewinding the induction motor with super enamelled copper winding wire of existing gauge ,weight etc. and unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed.Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely |
| 43 | Supply and fixing in repair of Air presure meter in air compresssor complete all as specified and directed |
| 44 | Supply and fixing in repair of V belt in air compresssor complete all as specified and directed |
| 45 | Supply and fixing in repair of Air pessuer switch in air compresssor complete all as specified and directed |
| 46 | Supply and fixing in repair of Comprehesive maint of air compressor complete all as specified and directed |
| 47 | Supply and fixing in repair of Air presure line in air compresssor complete all as specified and directed |
| 48 | Supply and fixing in repair of Air filter in air compresssor complete all as specified and directed |
| 49 | S&F in repair of On load Change over switch, 100 Amps, 4 pole, 415 V, 50 Hz, fully compacted in 1.6mm thick CRCA sheet enclosure of suitable size and direct mounted & front operated type, manually operated, consisting of two sets of terminals for connecting two incoming supply sources alongwith all necessary accessories inclduing taking down old one complete all as specified and as directed. (Make: Havells/HPL/INDOASIAN/L&T) |
| 50 | M & L for repair of MS suction sweeper assembly 1200 mm x 300mm complete painting, replacement of all wheel , suitable size of wooden brush etc complete all as specified and as directed. |
| 51 | Servicing and repair of digital type water level indicator 150mm size digital display cable system including stem insertion for sensing the water level suitable for overhead water reservior with suitable fixing arrangement and other accessories also replacement of existing cable / wire connection from water level indicator display upto sensor (approx 100 RM) complete all as specified and as directed. |
| 52 | Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc (for taking out and laying pipe etc) not exc 10 Sqm in plan and getting out in soft/loose soil complete all as specified and as directed. |
| 53 | Returning, filling in, including spreading, levelling, as in soft/loose soil complete all as specified and directed. |
| 54 | Removing excavated material to a distance not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed. |
| 55 | Taking up 200 mm bore cast iron pipes (including all fittings) with spigot and socket end and lead joints including burning out lead joints and recovering lead complete all as specified and as directed. (Note : Excavation and earth work shall be measured and paid seperately.) |
| 56 | All as per Srl item No 55 above but size 150 mm bore complete all as specified and directed. |
| 57 | All as per Srl item No 55 above but size 100 mm bore complete all as specified and directed. |
| 58 | Supply, laying, connection and testing 200 mm bore, ductile iron pressure pipe centrifugally cast (spun) with spigot and socket ends, class K-7 and confirming to IS 8329 - 2000 with push on rubber gasket jointing inside with cement mortar lining and outside zinc coating with finishing layer of black bitumen/blue epoxy coating duly ISI marked in any length laid in trenches complete all as specified and as directed. |
| 59 | All as per Srl item No 58 above but size 150 mm bore complete all as specified and directed. |
| 60 | All as per SRl item No 58 above but size 100 mm bore complete all as specified and directed. |
| 61 | S&F 150mm bore, cast iron sluice valve both end flanged, class PN 1.6 conforming to IS -14846 (raising stem type) with iron wheel head and stainless steel spindle including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking up/down old sluice valve complete all as specified and as directed. |
| 62 | S&F 100mm bore, cast iron sluice valve both end flanged, class PN 1.6 conforming to IS -14846 (raising stem type) with iron wheel head and stainless steel spindle including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking up/down old sluice valve complete all as specified and as directed. |
| 63 | S&F 80 mm bore, Cast iron Non-return (reflux) valve, flange type with by-pass arrangement suitable for 80mm dia water mains conforming to IS-5312 Part-I class PN 1.6 including takind down existing one complete all as specified and as directed.(Make :Kalpana/Peco/Venus/Zoloto/RMCO) |
| 64 | Taking up or down 100 mm bore galvanised steel tubing including connections from trenches/wall/floor/ceiling etc and keeping serviceable pipes in safe custody for re-use at same site or other site complete all as specified and as directed.Note for 55 to 61 : Excavation of earth shall be measured and paid separately under respective item. |
| 65 | All as per Srl Item No 64above but size 80 mm bore complete all as specified and directed. |
| 66 | All as per Srl Item No 64 above item but size 50 mm bore complete all as specified and directed. |
| 67 | All as per Srl item No 64 above but size 40/32 mm bore complete all as specified and directed. |
| 68 | All as per Srl Item No 64 above but size 25 mm bore complete all as specified and directed. |
| 69 | All as per Srl item No 64 above but size 20 mm bore complete all as specified and directed. |
| 70 | All as per Srl item No 64 above but size 15 mm bore complete all as specified and directed. |
| 71 | Relaying/refixing 100 & 110mm bore galvanised steel tubing/PPR pipeline only jointing and testing of old GI pipes including cleaning completely in trenches/walls/floors as directed for the following sizes complete all as specified and directed. |
| 72 | All as per item No 71 above but size 80 & 90 mm dia complete all as specified and directed. |
| 73 | All as per item No 71 above size 50 & 63 mm dia complete all as specified and directed. |
| 74 | All as per item No 71 above but size 40 mm dia complete all as specified and directed. |
| 75 | All as per item No 71 above but size 25 mm dia complete all as specified and directed. |
| 76 | All as per item No 71 above but size 20 mm dia complete all as specified and directed. |
| 77 | All as per item No 71 above but size 15 mm dia complete all as specified and directed. |
| 78 | Supply, laying, connection and testing, 100mm bore, Steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures complete laid in trenches etc complete all as specified and as directed. |
| 79 | All as per Item No.78 above but size 80 mm bore complete all as specified and directed. |
| 80 | All as per Item No.78 above but size 50 mm bore complete all as specified and directed. |
| 81 | All as per Item No.78 here-in-before but size 40 mm bore complete all as specified and directed. |
| 82 | All as per Item No.78 here-in-before but size 25 mm bore complete all as specified and directed. |
| 83 | All as per Item No.78 here-in-before but size 20 mm bore complete all as specified and directed. |
| 84 | All as per Item No.78 here-in-before but size 15 mm bore complete all as specified and directed. |
| 85 | Taking out sluice valve of any size (200/150/100/80 mm) , any type and refacing, regrinding and refixing the same at existing locations using new gasket nuts, gland packing etc complete all as specified and as directed. |
| 86 | Repacking stuffing box of sluice valve spindle (200/150/100/80 mm) , any type including taking apart and reassembling complete all as specified and as directed. |
| 87 | M&L in repair for filling gland packing to control water leakage in sluice valve and centrifugal/monoblock pump sets of any capacity any type as and when required and all as specified and as directed |
| 88 | M&L for 15 mm dia stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed including taking out old one complete all as specified and as directed. |
| 89 | All as per Item No 88 above but size 20 mm bore complete all as specified and directed. |
| 90 | All as per Item No 88 above but size 25 mm bore complete all as specified and directed. |
| 91 | All as per Item No 88 above but size 40 mm bore complete all as specified and directed. |
| 92 | All as per Item No 88 above but size 50 mm bore complete all as specified and directed. |
| 93 | M&L 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or brass ferrule of 15mm bore including taking down old unserviceable valve complete all as specified and as directed. |
| 94 | S&F in repair for 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed. |
| 95 | Surface dressing n.exc 15 cm deep as in soft/loose soil and rubishes to a distance n.exc 50m including spraying pesticides (roundup or equivalent) to control the grass growth complete all as specified and directed. |
| 96 | M&L for Cleaning of valve pit chamber with sluice valve, pipes etc, 150mm to 200mm dia including replacement of existing wornout/defective gland packing, nut, bolt & washer, etc with new one to make the sluice valve perfectly leak proof including marking of flow direction of inlet & outlet pipe line with necessary colour coding with one coat of synthetic enamel paint after preparation of old steel surfaces valve pit cover complete all as required and as directed |
| 97 | All as per item No 96 above but for 80 mm to 100 mm dia complete all as specified and directed. |
| 98 | Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 150 mm bore complete all as specified and as directed. |
| 99 | Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 100 mm bore complete all as specified and as directed. |
| 100 | Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 80 mm bore complete all as specified and as directed. |
| 101 | M&L for run lead joint for cast iron spigot and socket pipes & fittings 150 mm bore with new lead and other jointing materials complete all as specified and as directed. |
| 102 | M&L for run lead joint for cast iron spigot and socket pipes & fittings 100 mm bore with new lead and other jointing materials complete all as specified and as directed. |
| 103 | M&L for run lead joint for cast iron spigot and socket pipes & fittings 80 mm bore with new lead and other jointing materials omplete all as specified and as directed. |
| 104 | M&L for cast iron fittings for spigot and socketed pipe, such as bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. \\"Y\\" junction, double branch, cross (all sockets or socket and pigot) collars, caps and plugs etc upto 150mm bore complete all as specified and as directed. |
| 105 | Road cutting & make good with PCC after rectified the pipeline leakage work etc, complete all as specified and as directed |
| 106 | Supply and fixing galvanised steel wire rope multistrand of size 8 Sqmm as per ISO 4309:2019 and safe for carry a point load of 48.6 KN/ 5 Ton, for lowering of pump/column pipe, complete all as specified and as directed by Engr-in-Charge. |
| 107 | S&F in repair bracing, supports, cleats, clamp, etc as per existing size and thickness fabricated from stuructural steel such as angles, flat, channel, etc as required for pressed steel tank & staging at 12 m to 15 m height including cutting, drilling holes, welding as necessary to suit the site requirement and including two coats of lead free black bituminous paint suitable for drinking water internally and two coats of aluminium paint over a coat of red oxide, zinc chrome primer externally after preparation of steel surfaces complete all as specified and as directed. |
| 108 | Dismantling existing pressed steel plate of size 1.22m x 1.22m x 5mm thick including taking out jointing bolts, nuts, washers, etc from 10000 gallons over head pressed steel tank installed at 12 to 15 m high staging for repair, cleaning, replacement of unserviceable plates, etc and removing unserviceable plates from site and keeping serviceable plates, bolts & nuts in safe custody for reuse in work complete all as specified and as directed.Note : Cost of staging/working platform as involved for the above operation in deemed to be included in the unit rate quoted by the tenderer. |
| 109 | S&F for factory made pressed steel plate of size 1.22m x 1.22m x 5mm thick placed on existing position at 12 m to 15 m high staging of over head water tank including necessary jointing/connecting materials such as lead wool, rubber gasket, bituminous compound with & including (new) mild steel bolts, nuts, washers, etc as required at site to make the joints perfectly leak proof all as per manufacturer's insturctions including testing of water tightness of the tank complete and including painting with two coats lead free black bituminous paints suitable for drinking water internally over a coat of primer and two coats of aluminium paint over a coat of red oxide, zinc chrome primer externally after preparation of steel surfaces complete all as specified and as directed. |
| 110 | Fixing only serviceable pressed steel plate obtained from item No 107 above after necessary repair, adjustment, cleaning, washing etc and connecting with jointing materials such as lead wool, rubber gasket, bituminous compound, bolts, nuts & washers etc as required to make the joints perfectly leaf proof and testing for water tightness of the tank complete all as specified and as directed.Note : (a) Old serviceable bolts & nuts obtained from item No 104 above shall be reused after cleaning. (b) New bolts, nuts & washers wherever required as a replacement of old one as directed by the Engr-in-Charge shall be measured and paid separately as Supply only under relevant item. |
| 111 | Dismantling existing pressed steel plate of size 1.22m x 3.75m x 3mm thick including taking out jointing bolts, nuts, washers, etc from 10000 gallons over head pressed steel tank installed at 12 to 15 m high staging for repair, cleaning, replacement of unserviceable plates, etc and removing unserviceable plates from site and keeping serviceable plates, bolts & nuts in safe custody for reuse in the work all complete all as specified and as directed.Note : Cost of staging/working platform as involved for the above operation in deemed to be included in the unit rate quoted by the tenderer. |
| 112 | S&F for factory made pressed steel plate of size 1.22m x 3.75m x 3mm thick, placed on existing position at 12 m to 15 m high staging of over head water tank including necessary jointing /connecting materials such as lead wool, rubber gasket, bituminous compound with and including machine made (new) bolts, nuts, washers, etc as required at site to make the joints perfectly leaf proof all as per manufacturer's instructions and including painting with two coats of lead free black bituminous paints suitable for drinking water internally and two coats of aluminium paint over a coat of red oxide, zinc chrome primer externally after preparation of steel surfaces complete all as specified and as directed. |
| 113 | Fixing only serviceable pressed steel plate obtained from item No 110 above after necessary repair, adjustment, cleaning, washing etc and connecting with jointing materials such as lead wool, rubber gasket, bituminous compound, bolts, nuts & washers etc as required to make the joints perfectly leaf proof and testing for water tightness of the tank complete all as specified and as directed.Note : (a) Old serviceable bolts & nuts obtained from item No 104 above shall be reused after cleaning. (b) New bolts, nuts & washers wherever required as a replacement of old one as directed by the Engr-in-Charge shall be measured and paid separately as Supply only under relevant item. |
| 114 | M&L for repairing of old joints of plates in position by unscrewing the jointing bolts, taking out jointing materials such as lead wire/tapes, lead wool, gasket, bituminous compound and replacing with new machine made bolts, nuts, washers as per existing size, gasket, lead wool, bituminous compound suitable for portable water and MS cleats wherever required complete to make the existing defective joints perfectly leak proof and testing for water tightness of the tank complete all as specified and as directed.Note : New bolts, nuts & washers wherever required as a replacement of old one as directed shall be measured and paid separately as Supply only under relevant item. |
| 115 | M&L for fabrication, installation, connection and testing of Glow sign LED 2D board of size 12 feet X 3 feet complete with acrylic raise alongwith LED Paseted on ACP rectangualr shape mounted on appropriate structure fixed with GI/MS Pipe structure as per site requirement fixed with nut and bolts and writing words as directed by engr in charge at the time of execution with wiring of circuit with copper cable incl electric connection for board. Approval for design of the sign board shall be taken by contractor from Engr-in-Charge at the time of execution complete all as specified and directed including taking down old unserviceable one . Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysSep 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender