Tender For Development Of Golf Course Sector-151A (Shaping, Drainage Irrigation, Safety Net And Related Other Works Etc.), Noida.
Tender Value
23.90 Crore
Estimated cost
Bid Submission
24 Aug 2026
3 days left
EMD
56.42 Lakhs
Bank guarantee accepted
Document Fee
8260
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ghaziabad → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Development Of Golf Course Sector-151A (Shaping, Drainage Irrigation, Safety Net And Related Other Works Etc.), Noida.
BOQ
| Sl. No. | Item Description |
| 1 | EARTH WORKS Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 3 | Sand filling in plinth including Supply of necessary quantity of sand from a distance not exceeding 8 km. (5 miles) from the site of work and including watering, ramming, dressing etc. labour and T & P etc. required for proper completion of the work. |
| 4 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete:With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
| 5 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level All works upto all levels: 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size) |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 8 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/Cum. Excess/ less cement used as per design mix is payable/recoverable separately). upto plinth |
| 9 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/Cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level |
| 10 | Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/Cum) |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases |
| 17 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level and above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 18 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 10 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 19 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 10 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 20 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 10 in superstructure above plinth level up to floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 21 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry |
| 22 | 12mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) |
| 23 | 15mm cement plaster on rough side of single or brick wall of mix: 1:4 (1 cement: 4 fine sand) |
| 24 | 6mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 25 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 26 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 27 | Melamine polishing on wood work (one or more coat) |
| 28 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood |
| 29 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters |
| 30 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm |
| 31 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm |
| 32 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm |
| 33 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 34 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100 mm |
| 35 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stoppers |
| 36 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm |
| 37 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16mm |
| 38 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 39 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.(The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) |
| 40 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge.(d) Finishing the surface with 20 mm thick jointless cement mortarof mix 1:4 (1 cement :4 coarse sand) admixed with water proofingcompound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. |
| 41 | Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck, using integral crystalline admixture @ 0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage |
| 42 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels /subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same fromnnegative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of selfhealing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm |
| 43 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels /subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of selfhealing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm |
| 44 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab upto 0.50 sqm |
| 45 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 46 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 47 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 48 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 800x800 mm |
| 49 | Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. |
| 50 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 51 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 52 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board |
| 53 | Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). |
| 54 | Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles. |
| 55 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase |
| 56 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 57 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. |
| 58 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density |
| 59 | Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer |
| 60 | Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge. |
| 61 | Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 20 mm wide and 15 mm deep groove |
| 62 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 63 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil 1.5m to 3.0m |
| 64 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil 3.0m to 4.5m |
| 65 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil 4.5m to 6.0m |
| 66 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) |
| 67 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 68 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cementconcrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade |
| 69 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Second class teak wood |
| 70 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 71 | Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 100x60x2.50 mm |
| 72 | Providing and fixing bright finished 100 mm mortice lock with 6 levers with pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. |
| 73 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 74 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 80 mm |
| 75 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 76 | 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 77 | Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick |
| 78 | Extra for pre finished nosing to treads of steps of marble / granite stone. |
| 79 | Extra for marble / granite stone flooring in treads of steps and risers using single length up to 2.00 metre. |
| 80 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 81 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer |
| 82 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 83 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar |
| 84 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality H D - 20 Circular shape 560 mm internal diameter |
| 85 | Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 86 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) |
| 87 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover |
| 88 | Providing and fixing ball bearing for rolling shutters. |
| 89 | Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area |
| 90 | Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured). |
| 91 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) |
| 92 | Granular Sub-Base with Close Graded Material (Table :- 400-1) (B) By Mix in Place Method, Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complet as per clause 401 |
| 93 | Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete. New work (Two or more coats) |
| 94 | Interior Civil Work Providing and fixing Charcoal Louverd panelling fixed on MDF base using tounge and groove joint design as colour and design as approved by Engineer-in-charge.make -ventura , E 3 clad ,euro Pratik MDF(12mm ply century,green,duro) Wood Details - Marindi , Mango Frame Size - 50 mm x50 mm |
| 95 | Providing and fixing PVC wall covering 1 to 2 mm thick as per design and finish having fibe backing for sound insulation.Covering to be pasted on mdf base with adhesive as approved by manufacturer,Material should be dire resistance as per ISO 105-B02>grade 8 All complete as per engineer in charge. make Aremstrong,Forbo,Tarkett, MDF(12mm ply century,green,duro) & Wood Details - Marindi, Mango Frame Size - 50 mm x50 mm |
| 96 | Providing and fixing 1mm thick designer laminate on 12mm thick mdf base with groove as per design and detail. Panelling work include base frame and all accessories as required all completed as per engineer in charge. Make Egger, Kronoswess, AV mstrong, MDF(12mm ply century, green,duro) & Wood Details-Marindi, Mango Frame Size - 50 mm x50 mm |
| 97 | Providing and fixing 5mm thick Lecquered glass on 12mm thick mdf base with adhesive as approved by manufacture. Cost include all adhesive and accessories as required all complete the work.Make Saintgobin,Jbglass,ASAI, Modi ,MDF(12mm ply century,green,duro) |
| 98 | Providing and fixing 375mm high brass letter logo brush finish to be pasted on existing base. Cost including all adhesive and accessories as required all complete the work. |
| 99 | Providing and fixing laminate, charcoal louver, door handle, door lock and floor spring, hings on door as required to refurbish existing door.make ventura,E3clad,EuroPratic ,MDF(12mm ply century,green,duro) & Wood Details - Marindi , Mango Frame Size - 50 mm x50 mm |
| 100 | Providing and fixing 12mm thick mdf finished with 1mm thick designer laminate both side of MS Frame structure made up of tublar section (50mmx50mmx4mm). Cost of work include all accessories as required for completion of work as per engineer in charge.make century, green lam, marino, MDF(12mm ply century,green,duro) & Wood Details-Marindi, Mango Frame Size - 50 mm x50 mm |
| 101 | Providing and fixing 12mm thick laminated wooden flooring scracth proof, moisture resistant abrasion resistant, texture finish on 6mm thick pu backing using toung and groove joint. Cost of work include all accessories as required for completion of work as per engineer in charge.make Span, pergo, wellspun, Wood Details - Marindi , Mango Frame Size - 50 mm x50 mm |
| 102 | Providing and fixing 12mm thick laminated wooden flooring scracth proof, moisture resistant abrasion resistant, texture finish 75mm high. Cost of work include all accessories as required for completion of work as per engineer in charge. make Span, pergo, wellspun , Wood Details - Marindi, Mango Frame Size - 50 mm x50 mm |
| 103 | Providing and fixing fabric curtain having visos. Cost of work include all accessories as required for completion of work as per engineer in charge. |
| 104 | Providing and fixing Roller open roman blinds having gsm 350,adjustable light,colour fastness grade 5,Grade guard certified, cost include all adhesive and accessories required to complete the work.make vista, Hunderdugles ,Nova fabrics |
| 105 | Providing and fixing PVC Flooring (2mm thick) of approved colour, shade and texture fixed with approved adhesive as per the manufactures specifications. The adhesive used for laying the PVC floor shall be as per the written recommendation made by the manufacturer. The PVC flooring shall be laid having seamless joints with proper joint treatment using matching shade PVC trims with soft welding as per manufacturers specifications only after Architects written approval on shade as per direction of engineer in charge.make armstrong,forbo,tarket |
| 106 | Providing and fixing polycarbonate sheet with 10 mm thickness of approved colour shade and texture and fixed with approved adhesive as per manufacturer specifications.The adhesive used for laying sheet shall be as per the written recommendattion made by the manufacturer with written aprroval on shade as per direction of Engineer in charge.make coxwell,Danpal,Jindal |
| 107 | Providing and fixing stretched fabric ceiling consisting of two basic components a perimeter track and light weight fabric membrane which streches and clips into the track.Installation: Aluminium track fixed with nuts and bolt to RCC ceiling at intervals as per design across the ceiling.Attach platform for light fixture or othersysytm(e.g smoke alarms)to the original ceiling.Adjust the height of the platform to pull relevant fixtures like light through ceiling and fits in place.To strech the ceiling fabric into place useheat to increase its elasticity.After achieving optimum elasticity it is fitted to thealuminium rack ,corners first.Glue the strengthening rings to the canvas and the puncture holes for the placement of the light fixtures and other system.Pull the cables to attach the liight fixture and other system.make Barrisol,Pandona Neolights |
| 108 | Providing & laying extremely abrasion proof & weather proof EPDM flooring and a sports surface on bituminous mat, consisting of a thicknesss of approx. 1 -1.5mm by applying 1/2 coats of SOFTBASE, a synthetic coating which fills in the porosity of bituminous bed, and 3/4 coatings, applied successively, of the special paste in the colour or colours required, with a total coverage of approx. 2.5 Kg/sq.m. This styrol-acrylic elastomer copolymer compound, following proper tamping of the bituminous conglomerate layers, gives a court surface with a playing speed very similar to that of clay courts. This type of court is extremely durable, requires no maintenance and is particularly resistance to UV rays and bad weather conditions.make ebbaco, Ecoflex,Swing craft |
| 109 | WALLPAPER DIGITAL 2D/3D WALL PAPER : Providing & fixing 2d/3d digital printing printing on approved paper / canvas / fabric media as per suggested graphic work on suggested surface .Contractor shall provide graphic work detail & 5 sqm sample for approval the work shall be done inclusive of all rate with accesesories,tool tackel at allheight compelte.make asianpaints, roberto,cavalli,coinianders |
| 110 | FABRIC ACOUSTICAL TREATMENT WALL PANELING: Providing and fixing of fire retardant fabric panels (colour as approved by the consultant) glued to 25mm thick melamine foam over a layer of 9 mm thick commercial ply with 15% perforations fixed over a framework of 48mm GI Stud of 0.55mm thk @ 600mm c/c . The ply to have perforations as per design drawings. The foam to be backed with 50mm 1000GSM thermally bonded polyester wadding. The rate includes for all Geometry of wall, openings etc. and for complete item including all the required approved material, labour and fixing as per drawings. The work shall be executed by the suppliers Authorized applicators. Approved Make: Malimiano of ABSOUND OVERSEAS, ANUTONE or equivalent. |
| 111 | Providing and fixing 8mm mirror fixed with wooden frame and clear silion as per design approved by Architect and Engineer-in-charge. |
| 112 | POP Moulding Providing and making decorative plaster of paris (super fine quality) cornice (cast in situ), moulding in the required profile and smooth in line and level to the entire satisfaction of Project Manager complete as per design and drawing |
| 113 | Providing and fixing 25mm PVD coated metal strip as per design approved by Architect and Engineer-in-charge..make fabrinox,Sds profile |
| 114 | Polyurethane Polishing to woodwork with required colour as approved by Engineer-in-Charge with preparing surface including scaffolding and hire charges of compressor machine including cost of filler and hardener material such as P. U. Sealing, P. U. Top coat (Matt/Glossy), Thinner, Spirit etc. and inclusive of all operation, material and labour complete as per direction of Engineer-in- Charge.make Sirca, Asian paints,ICA |
| 115 | Wooden Moulding Providing and fixing Red Meranti wood architrave/ moulding as per specification with necessary nails, screws etc. as required complete as per design and drawing. Of size 50mm x 25mm with Polyurethane Polishing in desired shade as per specification. |
| 116 | MIRROR PANELLING Fabricating and fixing of 48mm GI steel stud (Indian Gyspum / saint gobain or equivent) of 0.55mm thk cladded on to the required surface as per site conditions to existing wall surfaces in true level and plumb complete as directed and cladded with 12mm commercial ply as recommended with 10 mm thk Mirror Panelling to be stuck with 3m tape with Al \\"L\\" angles above and below the glass as per drawing and details.make glass saintgobin,ASAI,JBglass |
| 117 | POP On Wall Providing wall putty on new surface with approved quality material of Berger / J.K. / Birla or similar make 2 coats. |
| 118 | SS Material Golden Finish Supply & Fixing of Stainless steel doors, frames with 18mm thick beveled Toughened glass fixing with all hardware accessories all complete as per instructions and patterns and design of the Architect Make Panel size 4mHt x 1.2mwth Steel -SS304 Hardware- Kich,Ozone,hafle |
| 119 | LEATHER PANELLING Providing and fixing Leather panelling fixed on MDF base using tounge and groove joint design as colour and design as approved by Engineer-in-charge.make ventura |
| 120 | Granite Cladding Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8mm thick, Granite of any colour and shade. |
| 121 | White Sand Stone Claddding Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : Gang saw cut stone. 30mm thick White sand stone |
| 122 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required.make Hilti ,Rawl plug |
| 123 | Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. |
| 124 | 6mm thick toughened Glass Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With 6mm thick toughened Glass.make ASAI, Saintgobin, Tata |
| 125 | 6mm thick Tinted Black Glass Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With 6mm thick Tinted black Glass.make ASAI, Saintgobin, Tata |
| 126 | Trap Door Providing and fixing stainless steel ( Grade 316) Trap door including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the Trap door with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of slab with suitable arrangement as per approval of Engineer-incharge, |
| 127 | Brick Tile Cladding Providing and laying Brick wall tile cladding (size and thickness to be specified by the manufacturer), water absorption 3% to 6% conforming to IS: 1237:2001, of approved brand & manufacturer, in brick colours and shade as approved by the architect, on walls laid with cement based high polymer modified quick set tileadhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints of 3mm wide using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.make ARTIMOZZ, Unishine, Mytiles |
| 128 | Wooden Cladding PLY WALL PANELING FINISH WITH VENEER FINISH : Providing & fixing 12mm thick IS 710 ply fixed on frame work. The framework shall be fixed as per drawing vertically & @ 600 mm c/c vertical & 1200 mm c/c horizontally. The frame work shall be made from Aluminium section make JINDAL/HINDALCO conforming to IS specification In paneling, (intermediate, perimeter ) & (at vertical or horizontal joint of ply & at turning point ) shall be fixed to the wall/floor & ceiling with Sheet metal screws/Nylon grip screws of Corro-shield /Fischer and shall be supported by filling required size wedges /washers/ MS wall connectors or packings of teak wood /MS washers to ensure right angles and plumb level. All ply/wooden frameworks shall be treated with anti-termite treatment & hidden The framework shall be covered with approved make plywood(IS 710- 12 mm ply),adhesive ,tape, headless nails etc ,finished with Veneer ( veneer base 4 mm thick Gurjan ply) with semiglossy. PU polish & in pattern as shown in the drawing. Rate shall be inclusiveg grooves etc complete as per drawing or as directed by EIC/ Architect. The rate shall be in Sq.mt of actual paneling work for all floors, at all heights, all shapes .Rate shall inclusive of all material ,labor scaffolding, tools, tackles, for all heights and for all levels, Rates shall also be inclusive of cost of making cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers etc & providing additional sections for strengthening around the openings/cutouts, making grooves between wall & board or as per drawing /instruction of EIC. and no extra payment shall be considered for additional sections provided. All curved surfaces, recesses, waffles shall be part of the paneling including openable shutter wherever required area and finish with the same material. Rate shall be inclusive of all item inclusive part of paneling Only the clear elevation area shall be measured and paid. |
| 129 | Micro Concrete Providing and fixing Micro Concrete as per design and drawing as approved by Engineer-in-charge.make Sirrca, Bharat Flooring, colourstek |
| 130 | Teracotta Jaali Providing, Supplying and installing at site Teracotta Jallis decorative elements as per drawings and details made up of mainly White cement, High Silica sand, AR Glass fibre with Zirconium content not less than 16%, Admixtures, Hand cast or spraymix, cast premix process as per details provided in the drawings and site requirements/measurements and as per approved finish and color shade, with sealers and hardwares required, all in accordance with the manufacturer's specifications and conforming to Indian/ASTM/BS standards, along with submission of shop drawings for approval, complete in all respects Make bharat floors , Artimeze |
| 131 | SS Strips PVD Coated Supplying and fixing Stainless steel 304 grade Strips PVD coated profiles T-Shape and N-Square Shape to be specified by the manufacturer fixed with weather sealants, rivets all as approved, using suitable bolts on steel work including necessary accessories complete in all respects including all scaffolding and labour charges etc.make fabrinox,Sdsprofile |
| 132 | Providing and fixing film etching with plotter cutting and application of 3MM/LUMAR/GARWARE make as per approved design on glass surfaces all complete as per instructions and patterns and design of the Architect.make 3m,lumar,gaware |
| 133 | Providing and fixing wall Graphics to be printed on vinyl with matt lamination in 3MM/LUMAR/GARWARE make as per approved design on glass surfaces all complete as per instructions and patterns and design of the Architect.Make 3m, lumar ,gaware |
| 134 | DUCO PAINT Providing and applying three or more coats of best quality DUCO paint of approved manufacture and shade to the applied evenly to give approved Matt finish, including preparation of surface and coat of approved primer complete as per specifications.make sirca,Asian paints,ica With Wooden Surface. |
| 135 | Providing and applying three or more coats of best quality DUCO paint of approved manufacture and shade to the applied evenly to give approved Matt finish, including preparation of surface and coat of approved primer complete as per specifications.make sirca,Asian paints,ica With Metal Surface. |
| 136 | Providing and installation Tennot 3d wall panels as per approved sample and design as per drawing complete. |
| 137 | HDHMR WALL PANELLING Providing and fixing factory made 30MM (18MM Flutes + 12 MM Base) thick Homogeneous HDHMR pasted on a 12 MM thick HDHMR Plain Board with a second Generation alumnimum polymer based hybrid All surface sealant, pressed in Temperature & Pressure controlled press, Solid Dark Green Colour board Fluting Panel, with CNC (Computer Numeric Control) Routed of approved design (Rectangular or Arched or both) by Engineer-in-charge which are machine cut for Panelling/Partitioning and acoustic Purposes comprising of Wood Fibre/Wood chips & synthetic thermosetting resin, having a minimum density of 820 kg/Cum and screw Withdrawal strength of 1500 N (Face), 1250 N (Edge), Modulus of Elasticity average, 3200N/mm2, Modulus of rupture average 3200N/mm2 with properties of being termite/borer proof, moisture/water Wall Paneling: Providing and fixing factory made 30MM (18MM Flutes + 12 MM Base) thick Homogeneous HDHMR pasted on a 12 MM thick HDHMR Plain Board with a second Generation alumnimum polymer based hybrid All surface sealant, pressed in Temperature & Pressure controlled press, Solid Dark Green Colour board Fluting Panel, with CNC (Computer Numeric Control) Routed of approved design (Rectangular or Arched or both) by Engineer-in-charge which are machine cut for Panelling/Partitioning and acoustic Purposes comprising of Wood Fibre/Wood chips & synthetic thermosetting resin, having a minimum density of 820 kg/Cum and screw Withdrawal strength of 1500 N (Face), 1250 N (Edge), Modulus of Elasticity average, 3200N/mm2, Modulus of rupture average 3200N/mm2 with properties of being termite/borer proof, moisture/water proof and fixing on Alumnimum frame made of 50 X 50 X 1.5 MM Square Hollow Box section and screws etc., all complete as per direction of Engineer – in – charge. (Note; Alumnimum framework shall be paid separately). (Make Greenlam, Ecoste, Century, Merlin Ply-la) |
| 138 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm. |
| 139 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm. |
| 140 | Providing and fixing bright finished brass handles with screws etc. complete : 125 mm. |
| 141 | Providing and fixing bright finished brass handles with screws etc. complete : 100 mm. |
| 142 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 143 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 144 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 145 | Painting with PU paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.make Sirca ,Ica |
| 146 | Providing and fixing wooden 100mmx60 mm moulded hand rails in place of rounded hand rail. (a) With 1st class Teak wood / Sissu wood. |
| 147 | Providing and fixing 25mmx25mm first class timber balustrade 25mmx25mm square, wrought fixed with ends housed (square or splayed) to hand rails and trends or strips complete. (a) With 1st class Teak wood / Sissu wood.make Dorma ,Haffle, Aceline |
| 148 | Providing and fixing PVD Rose gold finished brass tower bolts with necessary screws etc. complete approved by architect and engineer in charge: 450 x 8mm.make Dorma ,Haffle, Aceline |
| 149 | Providing and fixing PVD Rose gold finished brass tower bolts with necessary screws etc. complete approved by architect and engineer in charge: 600 x 10mm.make Dorma ,Haffle, Aceline |
| 150 | Providing and fixing brass handle with screws complete length 335mm finish as per selection and approved by architect and engineer in charge.make Dorma ,Haffle, Aceline |
| 151 | Providing and fixing brass handle with screws complete length 600 mm finish as per selection and approved by architect and engineer in charge.make Dorma ,Haffle, Aceline |
| 152 | Providing and fixing brass handle with screws complete length 800 mm finish as per selection and approved by architect and engineer in charge.make Dorma ,Haffle, Aceline |
| 153 | Furniture Work Providing Placing and Installing Reception Table L shape Size: 2800mm x600mm x 1150mm ht. as per drawing. Top Panel should be made up of 155mm granite and Side Front Panels to be made in 42mm thk laminated sandwiched Plpb made of inerior grade PLPB. Work-top, Front Panel and Support Panels shall be provided in 25 mm laminated interior grade PLPB-board. Adjustable levelling screws shall be fitted at the bottom of side panel. Drawer Side, back and bottom to be made in 18mm thk laminated interior grade PLPB boards. Drawer is fitted using part-estension telescopic channel of approved make. Drawer Facia to be made in 25mm thk laminated interior grade PLPB board. Factory pressed 1mm thk. laminate to be used on all exposed surfaces All Exposed edges to be sealed with 2mm thick PVC edge band and 0.8mm thick PVC edge-band to be applied on Non-exposed edges with the help of hot-melt glue through through fit edge-banding machines. The Edge-banding of exposed area to be done in the way that there should not be any sharp edge or corne left after processing. All the exposed edges should have buffing radius of 1.5 to 2mm without affection aesthetic value of the panel. Material used to produce the product should satisfy the following quality criteria.1) 1mm thk. laminate as per approved shade and make2) PLPB board used confirming to IS standard IS-12406:2003.3) Thin PVC foil of 0.2mm thickness.4) Hardware as per approved make.5) PVC edge-band used confirming to UV Light fastness ISO 4892-2 RATING OF 7 with ball test hardness to DIN53456 as 956) All M.S. component used to be Epoxy Powder coated followed by surface treatment by seven tank process of phospating (Surface activation Pre-treatment) Make:Godrej/Steelcase/Warila/Haworth/ Herman Miller/Rockworth |
| 154 | Providing Placing and Installing Reception ChairEQUIS RENOVADO The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with textured top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions recieved from Engineer Incharge. It shall be SCS IAQ certified for Indoor Air Quality.Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 155 | 3 Seater Sofa:- Providing Placing and Installing In Size 2400X 900 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leather and Malamine finish rubber wood legs. Make:Godrej/Steelcase/Warila/ Haworth/ Herman Miller/Rockworth |
| 156 | Meeting Table ( 10 Persons ): Providing Placing and Installing meeting table 10 seater 3000x1000x740: Table Top made of 25mm thick prelam particle board confirming to IS 12823 Interior Grade with the exposed edges sealed with 2mm PVC edge banding. The height of the table top from the ground should be 740mm. supported on the legs and beams. Legs are made of 50 x 50mm thick Square pipe made of 1.6mm thick CRCA pipe duly powder coated interconnected with tie member of 80 x 40mm pipe structure made of 1.6mm thick CRCA duly powder coated. The size of the beam is 100mm height and depth of 445mm for sharing. The powder coating thickness considered is 50 to 60 microns DFT. Structure to fully welded with all arc welding from inside eliminating manual finishing. Provision for wire management is through the vertical and horizontal of the mast made up of 1.6 mm thick CRCA bent into the C shape channel. The mast size is 500 x 105mm and cover is 0.7mm thick galvanized iron sheet in powder cated finish. The inner brackets are 3 mm thick CRCA. Provision for flip top box are patented DUO is also available for accessing wires from the table top. The leg shoe is made up of 100% recyclable nylon 6. The shoe helps in mounting of levellers on the legs by eliminating any welding process. The levellers are made of Nylon 6 with M8 bolts insert moulded to take care of any floor undulation. Beam is made of 1.2mm thick CRCA bent in the form of C channels with 3mm thick CRCA brackets. The bottom cover is made of 0.7 mm thick GI sheet. WIRE MANAGEMENT: - The vertical wire is carried through the mast and is carried in the horizontal direction by the beam which also acts as wire carrying member. The switches can be mounted on Duo provided above table top. Make:Godrej/Steelcase/ Warila/Haworth/Herman Miller/Rockworth |
| 157 | Providing Placing and Installing with fixed base nylonbase, castors, Nylon mechanism -Synhcro 1 all dimension in mm with open tolerance of +/-10mm Back rest :-The outer frame of the backrest made up of injection moulded in black polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has auto contoured lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black P.P and upholstered with U foam. Lumber support size 160mm (W) x 90mm (H) at fixed position Backrest size 650mm (H) x 530 (W). Seat :- The seat is made up of 12mm thick (7layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat size 495mm (W) x 510mm (D). Minimum and maximum seat height is 450mm and 550mm respectively. Back & Seat Foam :- Foam made out of moulded polyurethane foam with the following properties: Density: 45 – 55 Kg/m3 Hardness: 15 – 20 Kgf Compression set: 50% 10 Max Tensile strength: 1.03 Tear strength (Min) : 2.0 N/cm Resilience : 50% - 60% Comfort / Indentation Hardness : 15.4 Armrest :- ADJUSTABLE ARM: The armrests made up of black integral skin polyurethane with 45-55 Shore Hardness and reinforced with 4mm thick nylon insert. Arm pad size 265 x mm (L) x 95mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 30% Gas field nylon 20mm thick. rest with height adjustable up to 70mm.Minimum and Maximum height of armrest is 280mm/360mm respectively.Make:Godrej/Steelcase/ Warila/Haworth/Herman Miller/Rockworth |
| 158 | Providing and placing panel & tile based modular workstation, Size of 1500 MM W X 600 MMD x 750 H with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Tiles: Combination of top tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing board/ clear glass tile/ plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric magnetic / fabric / laminated /prelam. The panel thickness comprises of 38mm (35 mm Minimum) thick paper honeycomb + 3mm MDF on each sides + 0.6mm decorative laminate or fabric on both sides. The uprights and horizontals shall be made of aluminium extrusion having average wall thickness of 1.2 mm & powder coated with epoxy- polyester powder. Particle board framing is used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks are located in the mid segment of the panels and can be provided with cutouts for mounting switch boxes (above or below the worktops)Fabricated bottom frame for 52.4mm (50mm Minimum) panel comprises of L-channels made of 2mm thick CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062) & ERW steel tube of size 35 mm (30 mm Minimum) x15 mm (10mm Minimum)x1.6mm thick in oval cross section (IS: 7138) welded together. This frame is bolted to the uprights with M6 screws. Top tiles can be offered in variety of combinations. Worksurface- out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500mm x 600mm x 750H. Brackets shall be made from 2mm thick CRCA steel. Pedestals with legs - Nova pedestal flat metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm height 3dr = 2box+1file. The work shall be carried out as per the instructions and guidance received from engineer incharge. |
| 159 | Providing Placing and Installing Staff Table MESA ÓPTIMO able of size 1500x750x740mmH, side table of size 900x450x740mmH and 3 Drawer pedestal 350x450x550mmH, made of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels with PVC edge banding . Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management gourmets (Wipro Patented Squeeze) shall be provided on main or side table as specified by customer. All the exposed edges are with 2mm PVC edge Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. Kingsley Premium pedestal unit of size 350x450x550mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with post formed edge profile on top with premium central locking and 3 equal size drawers with roller slide mechanism for added mobility. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/ Rockworth |
| 160 | Providing Placing and Installing Revolving High Back Chair:-SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size 510mm (W) X 535mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per .Seat foam made out of moulded Polyurethane foam with Density: 50-60 Kg/m3, Hardness: 15-20Kgf and Tensile strength: 0.9-1.2 Kg/cm2ARM REST : The armrests made up of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 258mm (L) x 112mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel. 1D arms with height adjustable up to 80mm & front and back with adjustable up to 60mm. Arm rest tested for 60,000 Cycles to be completed with load of 40Kg as per SINGLE POINT SYNCHRO MECHANISM : Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 3°~10°. and back tilting angle is 87°~106°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles. GAS LIFT :Gas lift pipe diameter 50mm and has an Height adjustment stoke of 112mm. Gas lift tested for 1, 00,000 Cycles as per . Meets DIN 4550 Class 3 and all applicable ,performance standard Base:- Nylon base with castors : The base made up of injection moulded in black glass filled nylon and fitted with 5Nos twin wheel castors. The base is 658mm pitch circle diameter. The base tested for static load of 1134Kg . Make:Godrej/Steelcase/ Warila/ Haworth/ Herman Miller /Rockworth |
| 161 | Providing Placing and Installing The seat and back shall be made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and shall be upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of the back shall be 49.0 cm. (W) x 47.0 cm and of seat shall be 49.0 cm. (W) x 44.0 cm. (D). The HR Polyurethane foam shall be moulded with density= 45 ±2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest tops shall be injection moulded from black Polypropylene. They shall be fitted to tubular armrest supports made of dia 2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). The tubular armrest supports should hold together the seat and back. The tubular frame shall be cantilever type & made of 0 2.54±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60 microns). Overall Dimensions of Chair shall be Seat Height - 43.0cm, Height - 80.0cm, Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-61.0 cm. Make:Godrej/Steelcase/Warila/Haworth/ Herman Miller/Rockworth |
| 162 | Staff Table ( 6 Persons ): Providing Placing and Installing meeting table 6 seater 3000x1000x740: Table Top made of 25mm thick prelam particle board confirming to IS 12823 Interior Grade with the exposed edges sealed with 2mm PVC edge banding. The height of the table top from the ground should be 740mm. supported on the legs and beams. Legs are made of 50 x 50mm thick Square pipe made of 1.6mm thick CRCA pipe duly powder coated interconnected with tie member of 80 x 40mm pipe structure made of 1.6mm thick CRCA duly powder coated. The size of the beam is 100mm height and depth of 445mm for sharing. The powder coating thickness considered is 50 to 60 microns DFT. Structure to fully welded with all arc welding from inside eliminating manual finishing. Provision for wire management is through the vertical and horizontal of the mast made up of 1.6 mm thick CRCA bent into the C shape channel. The mast size is 500 x 105mm and cover is 0.7mm thick galvanized iron sheet in powder cated finish. The inner brackets are 3 mm thick CRCA. Provision for flip top box are patented DUO is also available for accessing wires from the table top. The leg shoe is made up of 100% recyclable nylon 6. The shoe helps in mounting of levellers on the legs by eliminating any welding process. The levellers are made of Nylon 6 with M8 bolts insert moulded to take care of any floor undulation. Beam is made of 1.2mm thick CRCA bent in the form of C channels with 3mm thick CRCA brackets. The bottom cover is made of 0.7 mm thick GI sheet. WIRE MANAGEMENT: - The vertical wire is carried through the mast and is carried in the horizontal direction by the beam which also acts as wire carrying member. The switches can be mounted on Duo provided above table top. Make:Godrej/Steelcase/ Warila/Haworth/ Herman Miller/Rockworth |
| 163 | Providing Placing and Installing Overall size of 6 - Door PLU + Lkr (Base) shall be 380mm(W)x450mm(D)x1830mm(H).R1 - 4 Sheets(Cam Lock) DMX Drg.- PL-13-A4-36467,R1-4 Sheets(Hasp.) Stackability shall have add - on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation . Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 164 | 2 Seater Sofa:- Providing Placing and Installing In Size 1890-X 900 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leatherette and Malamine finish rubber wood legs. Make:Godrej/Steelcase/Warila/ Haworth/ Herman Miller/ Rockworth |
| 165 | Providing and fixing tables of Center table Size - 1200mm W x 600mm D x 365mm H for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions ( |
| 166 | Supplying and Fixing Staff Table of size 1200x600x740mmH, s, made of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels with PVC edge banding . Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management gourmets (Wipro Patented Squeeze) shall be provided on main or side table as specified by customer. All the exposed edges are with 2mm PVC edge Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. Kingsley Premium pedestal unit of size 350x450x550mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with post formed edge profile on top with premium central locking and 3 equal size drawers with roller slide mechanism for added mobility .Make:Godrej/Steelcase/ Warila/Haworth/Herman Miller/Rockworth |
| 167 | Secreatory Room Table : Providing Placing and Installing Main table of size 2400x900x740mmH, side table of size 900x450x740mmH and 3 Drawer pedestal 350x450x550mmH,and back unit in size of 1800 x 425 x 740 (WDH)mm made of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels with PVC edge banding . Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management gourmets (Wipro Patented Squeeze) shall be provided on main or side table as specified by customer. All the exposed edges are with 2mm PVC edge Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. Kingsley Premium pedestal unit of size 350x450x550mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with post formed edge profile on top with premium central locking and 3 equal size drawers with roller slide mechanism for added mobility Make:Godrej/Steelcase/Warila/ Haworth/Herman Miller/Rockworth |
| 168 | Manager Cabin High Back Chair EQUIS MÁXIMO Made up of combination of 12mm (7 layers) & 4mm (3 layers) thick hot pressed plywood and 37mm thick, 32 Density U foam upholstered with fabric or Leather. The back ply and foam is designed with contoured lumber support for achieving comfortable seating posture. Back rest available in two sizes - High Back 860mm (H) X 550mm (W). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg as per ANSI / BIFMA X5.1. SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size 510mm (W) X490mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per ,Seat foam made out of moulded Polyurethane foam with Density: 50-60 Kg/m3 and Resilience: 50% - 60% ARM REST : The armrests made of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 248mm (L) x 92mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel. 2D arms with height adjustable up to 80mm & front and back with adjustable up to 60mm. Arm rest tested for 60,000 Cycles to be completed with load of 40Kg MECHANISM : FOUR POINT SYNCHRO MECHANISM : Mechanism with two lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 0°~6°. and back tilting angle is 89°~109°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles. GAS LIFT :Gas lift pipe diameter 50mm and has an Height adjustment stoke of 120mm. Gas lift tested for 1, 00,000 Cycles Meets DIN 4550 Class 3 and all applicable ANSI/BIFMA, EN performance standard BASE :ALUMINIUM BASE : The base made up of pressure die casted in aluminium fitted with 5Nos twin wheel castors. The base is 650mm pitch circle diameter. The base tested for static load of 1134Kg as per ANSI / BIFMA X 5.1. CASTERS : NYLON CASTORS : The twin wheel castors are injection moulded in nylon and diameter of Castor 50 mm. The castors are tested for 1,00,000 Cycles as per ANSI / BIFMA X 5.1. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 169 | MID Back Chair EQUIS MÁXIMO Made up of combination of 12mm (7 layers) & 4mm (3 layers) thick hot pressed plywood and 37mm thick, 32 Density U foam upholstered with fabric . The back ply and foam is designed with contoured lumber support for achieving comfortable seating posture. Back rest available in two sizes - Mid Back (MB) 700mm (H) X 550mm (W). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size 510mm (W) X490mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per,Seat foam made out of moulded Polyurethane foam with Density: 50-60 Kg/m3 and Resilience: 50% - 60% ARM REST : The armrests made of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 248mm (L) x 92mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel. 2D arms with height adjustable up to 80mm & front and back with adjustable up to 60mm. Arm rest tested for 60,000 Cycles to be completed with load of 40Kg MECHANISM : FOUR POINT SYNCHRO MECHANISM : Mechanism with two lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 0°~6°. and back tilting angle is 89°~109°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles as per GAS LIFT :Gas lift pipe diameter 50mm and has an Height adjustment stoke of 120mm. Gas lift tested for 1, 00,000 Cycles as per Meets DIN 4550 Class 3 a BASE :ALUMINIUM BASE : The base made up of pressure die casted in aluminium fitted with 5Nos twin wheel castors. The base is 650mm pitch circle diameter. The base tested for static load of 1134Kg as per ANSI / BIFMA X 5.1. CASTORS : NYLON CASTORS : The twin wheel castors are injection moulded in nylon and diameter of Castor 50 mm. The castors are tested for 1,00,000 Cycles Make:Godrej/Steelcase/Warila/Haworth/ Herman Miller |
| 170 | Office Table : Providing Placing and Installing Main table of size 1600x900x740mmH, side table of size 900x450x740mmH and 3 Drawer pedestal 350x450x550mmH,and back unit in size of 1800 x 425 x 740 (WDH)mm made of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels with PVC edge banding . Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management gourmets (Wipro Patented Squeeze) shall be provided on main or side table as specified by customer. All the exposed edges are with 2mm PVC edge Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. Kingsley Premium pedestal unit of size 350x450x550mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with post formed edge profile on top with premium central locking and 3 equal size drawers with roller slide mechanism for added mobility. Make:Godrej/Steelcase/Warila/ Haworth/Herman Miller/Rockworth |
| 171 | Manager Chair : Providing Placing and Installing High Back Chair model Thats with Headrest ,It in Fabric with fixed base nylonbase, castors, Nylon mechanism -Synhcro 1 all dimension in mm with open tolerance of +/-10mm Back rest :-The outer frame of the backrest made up of injection moulded in black polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has auto contoured lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black P.P and upholstered with U foam. Lumber support size 160mm (W) x 90mm (H) at fixed position Backrest size 650mm (H) x 530 (W).Seat :- The seat is made up of 12mm thick (7layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat size 495mm (W) x 510mm (D). Minimum and maximum seat height is 450mm and 550mm respectively. Back & Seat Foam :- Foam made out of moulded polyurethane foam with the following properties: Density: 45 – 55 Kg/m3 Hardness: 15 – 20 Kgf Compression set: 50% 10 Max Tensile strength: 1.03 Tear strength (Min) : 2.0 N/cm Resilience : 50% - 60% Comfort / Indentation Hardness : 15.4 Armrest :- ADJUSTABLE ARM: The armrests made up of black integral skin polyurethane with 45-55 Shore Hardness and reinforced with 4mm thick nylon insert. Arm pad size 265 x mm (L) x 95mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 30% Gas field nylon 20mm thick. rest with height adjustable up to 70mm.Minimum and Maximum height of armrest is 280mm/360mm respectively. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 172 | Providing and fixing Discussion 1050 Circular size : 1250 Dia. x 733 Height mm . The Discussion Table Worktop shall be made up of 25 mm thick PLT . The Discussion Table shall have Knocked Down Understructure made from 8 mm HR plate with levellers and a vertical support tube of diameter 90 and 2 mm thickness .Make: Godrej/ Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 173 | Providing and fixing The seat and Back are made up of injection moulded high impact strength PolyPropylene polymer compound with indoor grade UV resistance. Seat size shall be 52.5cm x 53.2cm. Back size shall be 51.6cm x 40.5cm. The tubular welded frame is made of dia. 2.22cm x 0.12cm and 3.5cm x 1.5cm x 0.12cm stainless steel 202 grade tube. The rubes are buff polished to give shiny finish. The shoes and Amrest are made of high impacy strength PolyPropylene polyemr compound with indoor grade UV resistance and pressed and press fitted with tubular frame. The overall dimensions of the chair shall be 52.4cm x 55.8cm x 84.5cm. The seating height shall be 45.0cm. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 174 | Providing and Placing Crafted with an outer frame of white-finished resin wicker wrapped around an inner MS frame, each chaise is weather-, water-, and UV-resistant, making them perfect for living on your patio or deck. Make: Godrej/Steelcase/Warila/Haworth/Herman Miller/ Rockworth |
| 175 | 1 Seater Sofa:- Providing Placing and Installing In Size 990-X 900 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leatherette and Malamine finish rubber wood legs.Make:Godrej/Steelcase/ Warila/Haworth/ Herman Miller/Rockworth |
| 176 | Providing and fixing The seat with cusion and Back with Cusion are made up of injection moulded high impact strength PolyPropylene polymer compound with indoor grade UV resistance. Seat size shall be 52.5cm x 53.2cm. Back size shall be 51.6cm x 40.5cm. The tubular welded frame is made of dia. 2.22cm x 0.12cm and 3.5cm x 1.5cm x 0.12cm stainless steel 202 grade tube. The rubes are buff polished to give shiny finish. The shoes and Amrest are made of high impacy strength PolyPropylene polyemr compound with indoor grade UV resistance and pressed and press fitted with tubular frame. The overall dimensions of the chair shall be 52.4cm x 55.8cm x 84.5cm. The seating height shall be 45.0cm. Make:Godrej/Steelcase/ Warila/ Haworth/ Herman Miller/Rockworth |
| 177 | MassageBED Single :- 900 (W) x 900(H) x 1800(L) for mattress size of 915 (W) x 1981 (L) , Under structure: - The legs are made of Square tube of size 25 x 25mm made out of MS pipe with a thickness of 1.2mm. The corner brackets are made of 2mm thick CRCA . Three nos. of Horizontal stiffeners are provided and made of Square tube of size 25 x 25mm made out of MS pipe with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. All Metal components are powder coated wiht 50-60 Microns DFT.Side Panel: - The side panels are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The overall width of the side panel is 150mm. The side panels have 18mm thick prelam particle board Baton running for required length to add rigidity to the structure.Head Board :- The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size is 1000 x 650mm.Foot Board :- The foot board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size is 1000 x 450mm.Bed Base: - The Bed Base is made up of 12mm thick Prelam Particle Board with both side White laminate.Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 178 | 4 Seater Round Sofa:-Providing Placing and Installing In Size 3990X 900 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leatherette and Malamine finish rubber wood legs. Make:Godrej/Steelcase/Warila/ Haworth/ Herman Miller/Rockworth |
| 179 | Providing and fixing tables of Center table Size - 1600mm W x 1200mm D x 365mm H for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions ( |
| 180 | Providing and Placing Bar Stool, Without Arm, PP Seat & Back, Gas Lift, Chrome Plated Pipe Frame, Footrest & Base. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 181 | 1 Seater Sofa:- Providing Placing and Installing In Size 1890-X 900 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leatherette and Malamine finish rubber wood legs.Make:Godrej/Steelcase/Warila/ Haworth/ Herman Miller/Rockworth |
| 182 | Providing and fixing tables of Side table Size - 600mm W x 600mm D x 365mm H for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions ( |
| 183 | Confrence Table 30 Seater Oval Shape Table MESA GUSTO Tops – Available in standard modules, made of 25mm thick PLPB with waterfall top edges finished in PVC Edge binding using unique wrap around technology for better aesthetics & long lasting use. Understructure – Legs made of 25mm thick standard Black matt colour post formed panels interconnected with 18mm thick standard Black matt colour pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. For closed configurations, liftable top cover, made of 12mm PLPB finishedwith Laminate, is provided to access the horizontal wire carrier. For open configurations, wire channel is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager. Standard table top height – 740mm. Designed for Flexibility through modular Construction, Laminatee Finish Tops for seamless surface, Post formed Legs for safe use, Provision for easy wire management, Upgradeable / reconfigurable for future needs. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/ Rockworth |
| 184 | 2 Seater Sofa:-Providing Placing and Installing In Size 1500X 900 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Pure Leather Upholstery - PigmentedDurable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the aesthetics. Make:Godrej/Steelcase/Warila/Haworth/ Herman Miller/ Rockworth |
| 185 | 3 Seater Sofa:-Providing Placing and Installing In Size 2000X 900 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Pure Leather Upholstery - PigmentedDurable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the aesthetics. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 186 | Providing and fixing tables of Center table Size - 1200mm W x 1200mm D x 450mm H for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions ( |
| 187 | Confrence Table14 Seater Oval Shape Table MESA GUSTO Tops – Available in standard modules, made of 25mm thick PLPB with waterfall top edges finished in PVC Edge binding using unique wrap around technology for better aesthetics & long lasting use. Understructure – Legs made of 25mm thick standard Black matt colour post formed panels interconnected with 18mm thick standard Black matt colour pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. For closed configurations, liftable top cover, made of 12mm PLPB finishedwith Laminate, is provided to access the horizontal wire carrier. For open configurations, wire channel is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager. Standard table top height – 740mm. Designed for Flexibility through modular Construction, Laminatee Finish Tops for seamless surface, Post formed Legs for safe use, Provision for easy wire management, Upgradeable / reconfigurable for future needs. Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/ Rockworth |
| 188 | Fitness Recumbent Bike Electro Magnetic System Resistance Control 12 Kgs. Fly Wheel Fully commercial Recumbent Fitness Bike for Home Fitness. Make Viva Fitness / Hercules/ Spranod/ Power Max |
| 189 | Provide and Placing TradeMill 4.0 HP powerful AC motor (2.0 HP continuous)Speed Range : 1~18 kmph.Power Incline: 0 ~ 18%Running surface : 19×56 inchesDisplay : Large LCD blue back lightReadout : time, speed, distance, incline, calories & pulseVarious workout programs, each is designed by certified personal trainers to help you run faster, loose weight & keep toned. Instant speed & incline keys on consoleInnovative cushioning systemHeavy duty running beltMP3 function with speakerWheels for easy transportationCylinder provides hand free deck folding systemEasily foldableMaximum User Weight : 120 Kgs. Make Viva Fitness / Hercules/ Spranod/ Power Max |
| 190 | Provide and Placing Assembled with “Universal Pivot Joint” for crank axle. Computer display for time, speed, distance, pulse, calories, RPM, scan, pulse recovery 15 level manual tension control 8 Kgs., Two ways, flat belt, disk crank Manual adjustable stride length With hand pulseTransport wheels Max User Weight 120 Kgs. Make Viva Fitness / Hercules/ Spranod/ Power Max |
| 191 | Provide and Placing Olympic Weight Bench Flat / Incline / Decline positions Adjustable incline for barbell set holder and seat Padded rollers and seat for maximum comfort Adjustable seat Max User Weight 100 Kgs. Make Viva Fitness / Hercules/ Spranod/ Power Max |
| 192 | Providing and Placing Multi Gym Innovative design and ideal for corporate & society use. Multi station gym with 1 steel weight stacks of 90 Kgs. Multiple Exercise Function – Seated bench press, Row, Pull down, Chest clamp, Tricep push down, Standing abdominal curl, Leg extension, Standing leg curl, Standing bicep curl, Golf, Arm extension, Front raise, Shrugs & Leg press. Durable powder coated finish.Comfortable seat pads. Arc cover for protection. LXWXH : 219X222X213 CM. Make Viva Fitness / Hercules/ Spranod/ Power Max |
| 193 | Providing and Fixxing Dumbbell Rack Made from Heavy Duty Cast Iron angles. Can hold 10 pairs of Dumbbells. Make Viva Fitness / Hercules/ Spranod/ Power Max |
| 194 | Providing Placing and Installing Reception Table Size: 2400mm x 600mm x 1100mm ht. Top Panel and Side Front Panels to be made in 42mm thk laminated sandwiched Prelam partical Board made of interior grade Prelam partical Board. Work-top, Front Panel and Support Panels shall be provided in 25 mm laminated interior grade Prelam partical Board-board. Adjustable levelling screws shall be fitted at the bottom of side panel. Drawer Side, back and bottom to be made in 18mm thk laminated interior grade Prelam partical Board boards. Drawer is fitted using part-estension telescopic channel of approved make. Drawer Facia to be made in 25mm thk laminated interior grade Prelam partical Board board. Factory pressed 1mm thk. laminate to be used on all exposed surfaces All Exposed edges to be sealed with 2mm thick PVC edge band and 0.8mm thick PVC edge-band to be applied on Non-exposed edges with the help of hot-melt glue through through fit edge-banding machines. The Edge-banding of exposed area to be done in the way that there should not be any sharp edge or corne left after processing. All the exposed edges should have buffing radius of 1.5 to 2mm without affection aesthetic value of the panel. Material used to produce the product should satisfy the following quality criteria.1) 1mm thk. laminate as per approved shade and make2) Prelam partical Board board used confirming to IS standard IS-12406:2003.3) Thin PVC foil of 0.2mm thickness.4) Hardware as per approved make.5) PVC edge-band used confirming to UV Light fastness ISO 4892-2 RATING OF 7 with ball test hardness to DIN53456 as 956) All M.S. component used to be Epoxy Powder coated followed by surface treatment by seven tank process of phospating (Surface activation Pre-treatment). Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 195 | Console: Providing and placing Console of Size 1800WX600DX900H The Console side panels and doors are made up of 18mm thick Commercial ply with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The shelves are made of 18mm thick Commercial ply with decorative laminate on both sides. The top is made of 36mm prelam particle board with decorative laminate on both sides. (18mm Prelam Particle board and 18mm batons on all sides to achieve 36mm overall thickness). The exposed edges of the top are sealed with 2mm thick PVC edge Banding. 3 nos drawer of size 600mmW to be provided at centre and 2 nos shutters of size 600mmW each to be provided on both side of console made of 18mm thick prelam Particle Board to be considered. The drawer will have a multipurpose lock of EBCO premium make. The console handles are Satin SS finish of 160mm pitch. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required. Sample to be approved by approving authority. |
| 196 | Corner Table:- Size 450 mm wide x 450 mm depth x 450 mm height.Center Table with 8mm thick Clear Glass top, Under-structure verticals are made up of 50mm thick MDF with 0.4mm thk European PVC foil & Horizontal support from 50mm thick Prelaminated MDF.All sides to have 0.8mm thk edge band. |
| 197 | Outdoor Wicker Furniture: ! no Table with 4 Chairs Outdoor Dining Arm Chair with cushion & fabric Size: 23\\" W x 25\\" D x 18\\" D, LI-4 Matching Dining Table with glass Size: 72\\" W x 36\\" D x 30\\" H Material - Jindal Aluminum in 1.66 mm thickness & German made wicker fiber from Viro Structure- Galvanised special all weather treated Jindal Aluminium alloy in 1.66 mm thickness Wicker: World most premium all weather UV resistant, zero VOZ, virgin HDPE German made Wicker fibre from 'Viro' Cushion : High Density Quick dry PU foam seat cushions Fabric: 'Loom and Spin' all weather solution dyed acrylic fabric made from Swiss technology. 100% UV, waterrepellent & Stain resistant UV. Make: Wicker World/Warila/ Decor Outdoor/ Wesource |
| 198 | Indoor Planters: These pots are made of virgin plastic( PREMIUM GRADE PLASTIC), UV treated high quality Eco-Friendly Durable Material - Super lightweight, sturdy polypropylene makes these classy planters stand a good deal of wear and tear, works great around kids or lively animals. Rest Assured Use to decorate your windowsill, desktop, shelf, bedroom, living room, kitchen, garden, and outdoor patio. size : 8 inch diameter, 7.5 inch height. These planters comes without drainage holes. You can simply place your old plants along with their pots inside this planter, In that case you dont require bottom plate for draining water and also your pot looks clean and neat, orelse if you want you can drill a hole at bottom for drainage to use them as pots for directly planting. |
| 199 | Outdoor Planters: Complete Plant Pruning Set, tall plant pot set it includes 1* Gardening Hand Pruner, 1* Watering Can, 1* Bag of Black Pebbles（2LB). Brighten up your gardening with QCQ Home Garden Pots! Plant your plants, trim plants and water flowers with our complete set now! Make Your Own Garden! 【21 Inch Flower Pots with 8-10 inch Dia】You will get 2 Large Plant For Outdoor Planters, 14” in Opening Diameter, 9” in Bottom Diameter, 21” in Height, fit nearly all large to medium-sized tall planters for outdoor plants, minimalistic styled plastic planters of classic Black color,will brighten up and bring life to your space. 【Built-in Drainage System】Each tall planter has a drain hole at the bottom to it makes possible to reserve or flow out excess water no matter where it’s placed, balcony, deck, patio, garden, outdoor and indoor. And keep the soil aerated and ventilated, to help prolong the life of your precious plants, convenient for easy planting and maintenance. 【Premium Eco-Friendly Material】These Front Porch Planters are made of high quality plastic,lightweight, no odor and will never be deformed or broken. The thick side walls are 10mm, Sturdy design Withstand harsh weather conditions, free from frost, crack and peel damage. Ensuring a long life compared with other planters. 【Modern Simple Design Plant Pot】Large planters are designed with full black matte finishing exterior, bringing out a modern minimalistic styled, the square planter pots are perfect for indoor and outdoor plants of different colors, perfect for home, office, hotels, restaurants, and other commercial use. Outdoor or Indoor - Ideal addition to any front entrance, poolside patio, or spacious hallway. |
| 200 | Integrated LED Mirror for bathroom of Size 18X15Inch: Adjustable Light Color and Intensity : Multiple color temperature Mode (Blue Light, Warm Light, Natural White Light) to simulate different lighting environments. Adjustable brightness levels for customizable illumination according to user preference. High-Quality Reflection : High-clarity mirror surface that delivers true-to-life reflection without distortion. Ensures accurate makeup application and grooming tasks.Modern Design : Stylish LED mirror that complements any smart mirror. Clean lines and a contemporary aesthetic for a polished look. Integrated LED Lighting : Built-in energy-efficient LED strips around the mirror. Provides consistent and flattering lighting for makeup application, grooming, and daily routines. Fog-resistant and Durable : Fog-resistant technology to keep the mirror clear even in steamy bathrooms. Sturdy construction and materials for long-lasting performance |
| 201 | Modular kitchen - Under counter storage cabinets: Providing & fixing factory made modular kitchen cabinets in modular type galvanized powder coated steel/E-Illate cabinet boxes with openable shutters, plain shelf units (of width vaires from 300mm to 800 mm) with required number of Partitions/shelves as directed by EIC, corner plain shelf units (of width 1000 mm), Under Sink units (600 mm to 800mm) and fillers of any size wherever required , made of 0.6mm body panels (bottom, back, sides) & 1.2mm thick horizontal frames of Galvanized sheet with zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like DuPont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H min. All shelves should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements. Shutters and drawers fascia shall be at least 18mm thickness BWP marine Ply IS-710 grade with laminate on both sides with 18mm wide 2mm thick PVC edge banding/lipping. Each shutter shall be fixed to the steel boxes / carcase using two numbers of best quality CED coated soft/Auto closing hinges as per requirement fixed with SS screws , nails etc. complete and these shutters are provided with an approved quality handles. Shelves will be of 0.6mm body panels & 1.2mm thick powder coated galvanized steel with bearing end support molding thickness of 12 mm. Modular kitchen baskets (payment for which will be made separately) to be fixed in the drawer/Cabinet with suitable provision with panels of bottom and rear shelves with thickness of 0.6mm. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs (Godrej, Hettich, Earl Bihari) which will be covered with PVC skirting (Rehau or equivalent make) in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from (DXH) 560 X 700MM (approx.) and join together as per site requirements etc. all complete as directed by the Engineer-in-Charge.Make:Godrej/Steelcase/Warila/Haworth/Herman Miller/Rockworth |
| 202 | Modular kitchen - Overhead storage cabinets: Providing & fixing factory made modular kitchen cabinets in modular type galvanized powder coated steel/E-Illate cabinet boxes with openable shutters, plain shelf units (of width vaires from 300mm to 1000 mm) with required number of Partitions/shelves as directed by EIC, and fillers of any size wherever required , made of 0.6mm body panels (bottom, back, sides) & 1.2mm thick horizontal frames of Galvanized sheet with zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like DuPont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H min. All shelves should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements. Shutters and drawers fascia shall be at least 18mm thickness BWP marine Ply IS-710 grade with laminate on both sides with 18mm wide 2mm thick PVC edge banding/lipping. Each shutter shall be fixed to the steel boxes / carcase using two numbers of best quality CED coated soft/Auto closing hinges as per requirement fixed with SS screws , nails etc. complete and these shutters are provided with an approved quality handles. Shelves will be of 0.6mm body panels & 1.2mm thick powder coated galvanized steel with bearing end support molding thickness of 12 mm. Modular kitchen baskets (payment for which will be made separately) to be fixed in the drawer/Cabinet with suitable provision with panels of bottom and rear shelves with thickness of 0.6mm. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs (Godrej, Hettich, Earl Bihari) which will be covered with PVC skirting (Rehau or equivalent make) in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be (DXH) 310 X 600(approx.) and join together as per site requirements etc. all complete as directed by the Engineer-in-Charge.Make:Godrej/ Steelcase/Warila/ Haworth/ Herman Miller /Rockworth |
| 203 | Providing and Fixing Table Tennis Table19 MM Laminated Top 75 MM Lockable Wheels & Levelers Size of Tournament Grade Table Tennis Table by Deuce . 19 Mm Both Side Pre Laminated Tt Table Top, Anti Glare(Matte) Pu Roller Painted Matte Finish Top, Ms Steel Metal Frame and Legs, 75 Mm Wheels - Folding and Roll Away Model Regulation Size : 2740x1525x760 Mm , Top : 19 Mm Both Side Pre Laminated, Tournament Quality Table Tennis Top , Main Frame : 40x20 Mm Ms Steel Frame (Powder Coated Metal Frame) Legs : 38 MM Square Legs With Height Adjustable Leg Levelers and 75 Mm Caster Wheels , Wheels : 8 Wheels 75 Mm Size. It Is a Foldable and Rollaway Model Which Makes the Storage and Movement of the Table Easy Package Contains : 1 Deuce 801 in Tt Table, 1 Set Deuce Tt Play Set Consisting 2 Bats and 3 Balls , Tt Table Cover(Multi Purpose Cover), Net and Net Clamps. Suitable for School, Colleges and Other Community / Commercial Play. Recommended for Home and Offices Also . Installation : Do It Yourself(Diy) Required, Foldable : Yes, Includes in Package :tt Table, Tt Net, Net Stand, User Manual, Required Hardware for Table Installation |
| 204 | Providing and Fixing Solid Wood Pool Table Size 2.44L x 1.22W x 0.84H Meters matrial Solid Wood Pool table is elegantly designed and manufactured using the finest selection of hardwood and Marble. Excellent finish, high quality fabric on top, leather pocket covers and precision leveled for a genuine playing experience. The body is made from pine wood, cushions made from steam beech wood and six legs made from solid sheeshan wood. Playing surface made from 3-piece natural slate in 38 mm thickness, the billiard table can be easily set up even in hard-to-reach areas. This stunning table has all of the perks of a professional table with the added bonus of looking fantastic in your club, restaurant, home etc. |
| 205 | Providing and fixing Discussion 1050 Circular size : 1250 Dia. x 733 Height mm . The Discussion Table Worktop shall be made up of 25 mm thick PLT . The Discussion Table shall have Knocked Down Understructure made from 8 mm HR plate with levellers and a vertical support tube of diameter 90 and 2 mm thickness .Net Poker Table Green Poker Folding Table Top for 8 Players Octagon 122cm (48\\" ).Big Table Top for 8 Players: Designed with octagon shape and classic green, this professional poker table top will bring you with an excellent casino experience.The big table top allows more players to join the game together, which makes it a great partner for you and your friends to play poker, blackjack, and texas holdem. ?? Soft Surface & Thickened Table Board: Made of felt surface and stable underside, it efficiently prevents the discomfort with table cloth moving and the over-sliding of cards. 3.The thickened board makes it more stable to put on any plane. Its smooth and soft touch will also make you comfortable in playing. ?? Intimate Cup Holder and Chip Tray: The seat of each player has a corresponding cup holder and chip tray. 4.This intimate design provides players with a convenient place to hold their water and drinks in less mess. 5.The specially manufactured chip tray is just right for the size of the chips, which makes the desktop more tidy. ?? Easy to Fold and Take Along with: The four-fold design makes it easy for you to store while not in use. Equipped with a dedicated oxford bag with handle, it provides a big convenience for you to carry. Make:Godrej/Steelcase/ Warila/ Haworth/ Herman Miller/Rockworth |
| 206 | Facade Work, Texture Paint Painting with Extirior texture applying of Exterior texture (Stone texture) with primer base. |
| 207 | External Claddding Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). Red sand stone - 30mm thick gang saw cut stone |
| 208 | Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge. for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid). |
| 209 | HPL CLADDING Supply and Installation of 6mm thick Exterior grade F- Quality panels of standard size with both side décor . Exterior panels are Duromer high-pressure laminates (HPL) as per EN 438-6 type EDF manufactured with norm conformity of EN 438-7 using patented NT Technology (NT is Non fading high performance acrylic polyurethane surface Technology). Panels will be double hardened including acrylic polyurethane resin and thermally cured under high pressure. These Panels will have CE-Mark necessary for their use in building applications. Installation of panels will be done by MBE Rivets (with Fixed and Sliding Points) with recommended Aluminum T section of 75x37x2.8 mm thick and L section 38x38x2.8mm thick held by Aluminum Wall Bracket with Wind load and Dead load slot as designed and provided by Fundermax India pvt. ltd., anchored by standard anchor fasteners along with Thermal Separator. Installation of Panels will be done using Rear Ventilated Principles only, which is ensured by providing ventilation gap minimum 200 cm2/ per Meter (for free flow of air behind the façade) for the façade and using the framework with no horizontal section. (Make Funder max, Kumarsons, Omnific fitouts LLP or Equivalent ). |
| 210 | Zinc Cladding Providing and fixing of Zinc Titanium wall cladding in 0.8mm thickness Tltanium-zinc quartz strat finish Tltanium-Zinc consists of rolled zinc alloyed with copper and titanium that compiles with european standard EN 988. Joint type flat lock system. Flat lock oanels of maximium 390mm width and upto 2000mm length fixed to the substrate using galvanised strips & clips. Clip thickness 0.4mm. The clip is deigned to with stand negative load requirements pull out strength 50daN exact length shall be decided after on site dimensions / GFC Drawings. The finish shall be preweathered zinc finish with a surface treatment consists of chemically converting the upper crystalline structure of the metal that transforms zinc into zinc phosphate. It gives rolled zinc a bright grey aspect, similar in colour to the patina that forms on natural zinc after several months of exposure to the atmospere he average characteristics of this conversion coating are as follows. |
| 211 | ACP Cladding Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 212 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. |
| 213 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. |
| 214 | Tensile Structure Supply, fabrication of MS frame consisting of M.S. pipes, base plates & normal anchors. The frame shall be welded and grinded to smooth finish as per drawing. 1- Painting- The MS frame shall be cleaned of girt/grim and oil/grease deposit. The frame shall be sand papered to remove rust. The frame shall be painted with PU primer to finish. After primer the frame, NC putty shall be applied over the frame and it will be wet sand papered to a smooth glossy finish. The ready surface will be painted 2 coats of PU paint 2 -Fabric: Providing & fixing of Fabric- Fabric Ferrari 902 over frame including wire rope and plates. The fabric will be welded to shape and pattern. The joint shall have weld width of 40mm. The joint will have a homogeneous welded of 40 mm The fabric shall be installed, tensioned using a tensioning device and shall not sag at any point. the fabric will be fixed on the frame with fixing accessories like aluminium section with powder coated top covers, self drilling screws. make-mehler ,ferrari |
| 215 | GRC Jali Providing and fixing GRC Jaali size L 4800mm x W 2300mm x 75mm bordar & 25mm Pattern thickness including loading, unloading cartage all complete as per design approved by consultant & Engineer-in-charge. |
| 216 | HDPE PAVER Providing and laying 80mm thk. HDPE grass paver block flooring of M-30 grade as per approved sample and design as per drawing including filling of the joints with 50mm thk. sand bed, cutting edge pavers with cutter to required shape, size and pattern and setting with vibration complete , including edge protection etc complete in all respects as per manufacturers specification. |
| 217 | Scaffolding system Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. |
| 218 | Thermo Pine FSC®/PEFC® certified products - please check for available dimensions and profiles profiled (smooth or grooved) Golden Brown. Color variations in thermally modified wood are a result of variations in growth conditions of the tree and are fully acceptable. Wood will weather to grey unless an UV resistant coating is applied and maintained. Thermory AS applies no coating 26mm (But your material’s thickness will be approx. 10.5mm because slicing of 26mm Thermo Pine material.) 120mm & 140mm (any other is subject to availability). 3 Mtr. - 5.4 Mtr. (lengths are subject to availability). Thermory® cladding boards should be stored out of the sun, rain and other elements. When this is not possible, boards need to be elevated off the ground, stacked uniformly and covered with a waterproof tarp. Leave the ends of the tarp open so moisture is not trapped inside, making certain the stored wood is not subjected to the elements or sun as UV rays will fade the material. Under no circumstances should Thermory® boards, even in original packaging, be subjected to rain or any moisture as they cannot dry properly when stacked and/or packaged. Fixing with either clips or screws depending on the profile. Wood-to-wood contact should be avoided. More information from file: “Thermory Cladding Installation Guide” Thermory® cladding does not require surface treatment. However, as with any wood, Thermory wood will naturally age to a grey over time. This process will start immediately and, depending on the amount of UV exposure, will take anywhere from several months to a year. This does not make the wood any less resistant to decay. Regular care and maintenance is recommended to make your cladding last longer. The Golden Brown color can be preserved by treating with UV resistant oil once a year. More information from file: “Thermory Cladding Installation Guide” Thermory naturally enhances wood using only heat and steam. Thermally modified wood does not need to be treated as hazardous waste. |
| 219 | Supply and fabrication of pre-coated solid aluminium panel cladding systems. Panels made from high-corrosion-resistant aluminium alloys AA 3003, AA 3105, AA 5005 –H44, or AA 5754 – H42. The panels shall have a thickness of 3.0 (SX3) mm, with a density ranging from 2.66–2.73 g/cm³. The panels shall feature either standard or customized finishes and patterns as per the architect’s design. The front surface shall be coated using PVDF – Kynar 500 /Hylar 5000 (70/30) or FEVE paint in accordance with AAMA 2605 standards, ensuring resistance to UV, corrosion, chalking, abrasion, and minimal fading over time. The front coating thickness shall be 25 +/-2 µm for a 2-coat system, providing a 15-year warranty, while the rear side shall have a treated mill finish or service coat with a thickness of 5-7 µm. The panels shall be available in dimensions ranging from 500 mm to 1550mm in width and up to 4500 mm in length, offering flexibility in design to meet the aesthetic and functional requirements of the project. The pre-coated aluminium solid panels shall conform to the reaction to fire requirements as per EN 13501-1, achieving Class A1 s0, d0. This classification ensures that the material is non combustible The Manufacturer should hold an Environmental Product Declaration (EPD) certificate The panels shall be manufactured using advanced CAD/CAM equipment that includes multiple levelling stages in the manufacturing process to ensure optimal flatness. The coating should be applied to the coil using roller coating technology to ensure a uniform, defect-free finish with consistent colour, minimizing variations and enhancing overall quality. The finish side of the panel shall have a removable UV-resistant protective film applied prior to fabrication, during the coil coating process. The coating direction shall be clearly marked on the protective film. This removable protective film must remain on the panel during fabrication, shipping, and erection to safeguard the surface from any potential damage. The rear side of the panel shall be marked with essential details, including the finish code, finish name, coil thickness, type of paint, date of manufacturing, and batch number. Additionally, the pre-coated panel manufacturing company shall have a minimum of 5 years of continuous experience in producing coated coils Made in India in-house, ensuring consistent quality assurance and finish integrity.Make : Viva / Novelis |
| 220 | Sculptures Providing and fixing of Decorative wall (IAM NOIDA) of Size 5000mm height approx in 75x100mm MS sections with letters in laser cuttring aluminium finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge.with Foundation and PU paint |
| 221 | Providing and fixing of Colourful swing sculptures of Size 3000mm height approx in 1000x500mm MS finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 222 | Providing and fixing of Big ball sculptures of Size ball dia 1800mm, ball stand height 2000mm from floor finish level total 3800mm height approx metal finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 223 | Concrete bench with planter supply of glass fiber reinforced concrete bench as per approved design, the planter should be casted in fiber reinforced plastic molds allowing tolerence +10 mm. The wall thickness should be minimum 25 mm, casted in portland cement based of J.K. Cement, Ultratech or equivalent, using appropriate reinforced with alkali resistence glass fiber rainging from 3 to 5% of N.E.G. Japan or ownes cornng. The bench should be pigmented with synthetic oxide non fading water proof, UV resistance pigment of M/s Bayferrox / Lanxess of equivalent. The outer surface need to be coated with sealer. |
| 224 | Dustbin - MSWD8 Dim. - 370 L x 340 W x 875 H mm, Capacity - 50 ltr Construction - G.I. powder coated frame with 7Dx12mm synthetic wood planks cladding (synthetic wood is a composite material of wood & plastic which makes it termite free and weather resistance & has a good self life). Inner Removable Bin for waste removable |
| 225 | Concrete Bench TR Concrete bench Supply of concrete bench as per approved design casted in FRP mould for uniform surface straingthness and appropriate edge precasted with M-25 concrete mix appropriate reinforcement, the other surface to be coated with sealer. |
| 226 | Signages Providing and fixing of Signage of Size 3000x600x150mm height approx in MS finished as per attached drawing/image and placing on finished platform as attached drawing without damaging the edges complete as per instruction from consultant and Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysAug 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender