Bids Are invited for Special Repair Surveyed Off Condemned Furniture For The Qe Jun 2025 Under Ge Minniebay

Sharing tender

Bids Are invited for Special Repair Surveyed Off Condemned Furniture For The Qe Jun 2025 Under Ge Minniebay Almirah Large With Shelves Steel - Dimension Overall Size Shall Be 1985Mm High Comma 920Mm Wide And 485Mm Deep. Description The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Bases Made In U Shaped With Ends Covered. Mild Steel Sheet Shall Be 1Mm Thick. The Base Channel Shall Be Welded At 50Mm From Each End Of The Length Of 920Mm And Shall Be Up To Full Width Of 485Mm And Shall Be 100Mm High Top Comma Sides Bottom And Back Of Almirah Shall Be Of 1Mm Thick Mild Steel Sheet. Four Shelves Equally Spaced Of 1Mm Thick Mild Steel Sheet Shall Be Provided To Make Five Compartments. Front Shutter Shall Two Leaves Of Equal Size. Front Shutter Leaves Shall Have Three Butt Hinges Of 75Mm Fixed To Each Shutter And Shall Be Side Hung. All Joints And Welding And Fixing Shall Be Done In Accordance With The Standard Workmanship. Handle One Chromium Plated Steel Handle With A Locking Device Shall Be Provided As Shown On Drawing. Locking Device The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate. Finish All Steel Surfaces Shall Be Painted With Two Coats Of Smoke Grey Paint Internally And Extrenally With Spray Machine Over A Coat Of Red Oxide Primer After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Left Corner Of Front Shutter With Visible Colour. Painting Shall Be Done With Spray Machine. Rest All As Per Drg. , Book Case Small - Overall Size Shall Be 1025Mm Long Comma 450Mm Wide And 750Mm High. Back Shall Be 1025 Mm Long And 750 Mm High Made Out Of Prelaminated Hdf Board Bd 18Mm Thick One Side Teak Comma Walnut And Other Side Balancing White Comma Rest All As Per Drg And As Directed By Engr In Charge. , Charpoy Ip With Hard Top - Overall Size Shall Be 1980Mm Long Comma 900Mm Wide And 440Mm High. Two Long Rails And Two Short Rails Shall Be Of 25Mmx65mmx16 Gauge Ms Rectangular Pipe. The Legs Shall Be Of Size 32Mmx32mmx16 Gauge Welded To Long And Short Rails As Shown On Drg.Two Stiffeners Of Size 25Mmx25mmx16 Gauge Shall Be Provided In Equidistant Between Two Opposite Long Rails. Six Number Cleat Of Size 25Mmx60mmx6mm Shall Be Welded With Frame To Support Ply. Two Stiffeners Joining Legs Of Size 25Mmx25mmx16 Gauge Shall Be Provided At 150Mm From Ground Level. 12Mm Thick Bwr Plywood Shall Be Provided For Top As Shown On Drg With Proper Nut And Bolt .One Nut And Bolt Shall Also Be Provided At Centre Of Each Stiffeners For Fixing The Plywood Irrespective Of What Is Shown On Drg. Pvc Hard Rubber Shoes Shall Be Fixed At Bottom Of Each Leg. All Steel Surfaces Shall Be Painted With Synthetic Enamel Paint Black In Color After Applying A Coat Of Primer. Rest All As Per Drg , Locker Bed Side Steel - Dimension Overall Size Shall Be 760Mm Long Comma 600Mm Wide And 1100Mm High.Description The Locker Shall Be Made Of Mild Steel Sheet 1Mm Thick. 20 Mm Dia Conduit Pipe Shall Be Chrome Plated With Wall Thickness Of 1 Point 6 Mm Shall Be Fixed With Side Sockets. Two Handles Chromium Plated 100Mm Long Shall Be Fixed To Shutters With Necessary Riveting. One Hasp And Staple 75Mm Long Shall Also Be Fixed To Shutters With Riveting. The Left Shutters Shall Be Provided With 100Mm Long Tower Bolt Inside At Upper And Lower Ends Also. The Locker Shall Be Provided With Compartments As Shown In Drgs Made Of 1Mm Ms Sheet. Finish All Steel Surface Internally And Externally Comma Exposed To View When Placed In Position Shall Be Given Two Coats Of Smoke Grey Paint Internally And Externally After Properly Smoothened The Surface With Sand Paper And Applying Putty. Painting Shall Be Done With Spray Machine. Rest All Specifications Are As Per Drg. , Rack Adjustable 6 Tier Steel - Dimension Overall Size Shall Be 915Mm Long Comma 610Mm Wide And 1905Mm High.Description The Entire Rack Shall Be Made Of 1Mm Mild Steel Sheet. The Sides Shall Be Provided With 40X40x4mm Angle Iron Welded To 1 Point 00Mm Thick Ms Sheet. 75X75x3mm Thick Flat Iron Cut To Shape Shall Be Welded At Front Corner. All Partitions Shall Also Be Made Of 1Mm Thick Mild Steel Sheet And Shall Be Riveted To Side Of Rack. All Dimensions Comma Shape And Size Shall Be Followed As Per Drg. All Joints Comma Fixing Shallbe Done In Accordance With Standard Specifications. Rest All As Shown On Drg. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Smoke Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. Painting Shall Be Done With Spray Machine. Rest All As Per Drg. , Table Dressing Gents With Mirror - All As Per Drg Comma The Frame Shall Be Strictly As Per Drg Wallet Oblique Teak Colour As Approved. The Mirror Shall Be Of 5Mm Thickness Of Make Modiguard Oblique Saint Gobain All Shown On Drg And As Directed By Engr In Charge. , Table Dressing Ladies With Mirror - The Overall Size Of The Table Dressing Shall Be 1150Mm Long 380Mm Wide And 1700Mm High. The Sides Comma Top Comma Back And Front Of The Base Unit Shall Be Of 18Mm Thick Prelaminated Mdf Board. The Bottom Of The Side Units Shall Be Of 12Mm Thick Mdf Board. The Sides And Back Of Drawers Shall Be Of 12Mm Thick Prelaminated Mdf Comma Bottom Of The Drawers Shall Be Of 6Mm Thick Commercial Ply Whereas The Front Of The Drawers Shall Be Of 18Mm Thick Prelaminated Mdf Board. 5Mm Thick Electro Copper Plated Mirror Shall Be Fixed Over 6Mm Thick Plywood Back. Track Rails 25Mm X 25Mm In Section On One Side Telescopic Channel Of Make Hettick Oblique Ebbco Comma On Two Vertical. The Overall Size Of The Stool Shall Be 440Mm Long 350Mm Wide And 425Mm High. The Four Sides Shall Be Of 18Mm Thick Prelaminated Mdf. The Top Of The Stool Shall Be Of 12Mm Thick Plywood Openable As Shown In Drg. Four Heavy Duty Revolving Nylon Double Wheels Shall Be Provided At Base Below The 6Mm Base Ply Fixed Over Wooden Runner 20 Mm X 20 Mm. The Seat Of The Stool Shall Be 75Mm High Comma Made Of Foam 40 Density Covered With Tapestry Cloth As Approved By Engr In Charge Oblique Ge. Rest All As Per Drg. , Table Dining 4 Person - All As Per Drg Comma The Wood Shall Be 1St Class Hard Wood Teak Free From Any Joints Cracks And Knots. The Top Shall Be Made Out Of 18Mm Thick Mdf Board Exterior Grade One Side Teak Lamination In Wange Oblique Wallet As Approved Colour And One Side White Lamination. All Exposed Edges Of Ppb Shall Be Provided Wooden Beading Of Teak Wood 4Mm Thick X 18Mm Wide Duly Polished With Matching Colour The Frame Shall Be Polished After Prepration Of Surfaces With Two Or More Coats Of Brown Oblique Walnut Colour Melamyne Polish With Spray Machine As Per The Requirement To Its Glossy Look. Rest All As Shown On Drg And As Directed By Engr In Charge. , Table Writing Med - Dimension Overall Size Shall Be 1145Mm Long Comma 600Mm Wide And 760Mm High.Description All Wood Shall Be Of First Class Hard Teak Wood Except Top And Right Hand Side Drawer Cabinet. Legs Shall Be Of 35Mmx55mm In Section And 717Mm High Having 5Mmx5mm In Section Groove At The Top Of Legs At The Portion When Placed In Position. The Top Shall Be Of 18Mm Thick Of Approved Shade And The Edges Shall Be Covered With 4Mm Thick Teak Wood Beading. Two Short Stiffeners Of Teak Wood Of Size 50Mmx40mm In Section Irrespective Of What Is Shown On Drg Shall Be Provided Between Legs At 100Mm From Bottom Of Legs. Sides Of The Box Which House The Drawer And Cabinet Shall Be 18Mm Thick Bwr Grade Plywood Sides And Back Of Drawers Shall Be Of 12Mm Thick Teak Wood Planks. Bottom Of Drawers Shall Be Of 6 Mm Thick Plywood Commercial. 6Mm Thick Plywood Commercial 75Mm High Partition Shall Be Provided In The Drawer. Shutter For Cabinet Shall Be Fixed With Piano Type Continuous Hinges. Lock Shall Be Provided To Drawer And Shutters. Recessed Handle Shall Be Provided To Drawer And Shutter. 25Mm Dia And 25Mm High Rubber Shoes Shall Be Fixed To Bottom Of Legs. Finish All Wood Surfaces Shall Be Melamyne Polished With High Gloss Finishby Spray Machine. Rest All As Per Drg. , Teapoy Wooden - Dimension The Overall Size Shall Be 600Mm Long Comma 450Mm Wide And 540Mm High.Description The Legs Shall Be 60Mmx30mm In Section And 497 Mm High And Shall Be Of Teak Wood. 5Mmx5mm In Section Groove Shall Be Provided At The Visible Portion Of Top Of Legs. Top Rails Of Teak Wood Of 20Mmx50mm In Section And 510Mm Long Shall Be Provided Between The Legs. Bottom Rail Of Teak Wood Of 20Mmx50mm In Section And 420Mm Long Shall Be Provided Between Legs Comma Widthwise At 100Mm Above The Bottom Of Legs. A Centre Rail Of Size 20Mmx50mm Shall Also Be Provided Lengthwise At Centre In Between The Side Bottom Rails Irrespective Of What Is Shown On Drg. 25Mm Thick And 25Mm Dia Hard Rubber Oblique Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30Mm Long Screws. Top Of Table Shall Be Of 18 Mm Thick Pre Laminated Mdf Board With 4Mm Teak Wood Edging Alround The Top Of Table. Finish All Wood Surfaces Shall Be Melamyne Polished With High Gloss Finish By Spray Machine. Rest All As Per Drg , Hat Stand With Mirror - Overall Size Shall Be 1330 Mm Long Comm 710Mm High. The Inner Frame Shall Be Of 50Mmx20mm Teak Wood Battens Six In Nos. The Back And Front Of Frame Shall Be Covered With 6Mm Thick Commercial Ply. The Edges Of The Frame Shall Be Covered With 6Mmx35mm Teak Wood Edging Fixed Alround The Frame With Headless Nails And Adhesive. Six Brass Pegs 120Mm Long Shall Be Fixed Over The Wooden Membrane With Brass Screws As Shown In Drg. 5Mm Thick Looking Mirror Of Saint Gobian Comma Modiguard Oblique Atul Shall Be Provided As Shown On Drg With Beading Alround. Mild Steel Key Plate Shall Be Provided At Both Top Corners Of The Hat Stand. All Exposed Surfaces Shall Be Given High Gloss Melamyne Polish With Lacquer Spray Machine Finish. Rest All As Per Drgs , Sofa Set 5 Seater - All As Per Drg Comma The Timber In All Around Shall Be First Class Hard Wood Teak Comma The Cushions Shall Be Made Out Of Pu Foam Of Min 40 Density Of Approved Make And Covered With Tapestery Cloth Of Approved Quality Comma Pattern And Colour Before Incorporating In Work. The Frame Shall Be Polished After Prepration Of Surfaces With Two Or More Coats Of Brown Oblique Walnut Colour Melamyne Polish With Spray Machine As Per The Requirement To Its Glossy Look Rest All As Shown On Drg And As Directed By Engr In Charge. , Chair Computer - The Base Pedestal Assembly Of Chair Computer Shall Be Of Dia 700Mm And 1060Mm High. The Pedestal Assembly Shall Be Provided With Injection Molded In Black 30 Percentage Glass Filled Nylon. A 10 Point 5Mm Dia Forged Bright Zinc Plated Ms Castor Pin Is Of Press Fitted Into Each Prong For Holding The Castors. The Seat And Back Of The Chair Computer Shall Be Made Of 12Mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam. The Back Form Shall Be Designed With Contour Lumber Support For Extra Comfort With Pvc Lipping Allround. The Back Rest Shall Be Adjustable And Consist Of Drop Lift Mechanism And Shall Be Adjusted In The Insert. It Shall Be Scratch And Weather Resistant. Rest All As Per S Le And As Approved By Ge , Rack Shoe Steel - Overall Size Shall Be 700Mm Long Comma 300Mm Wide And 880Mm High. The Legs Of The Shoe Rack Shall Be Of 25Mm Dia Ms Pipe Of 18 Gauge. The Five Shelves Of The Rack Shall Be Of 20Mm Dia Ms Pipe Of 18 Gauge Welded To Legs. The Shelves Shall Have 3Mm Dia Ms Rod 9 Nos In Widthwise And 3 Nos In Lengthwise Welded To 20Mm Dia Shelf Frame. Pre Treated With Powder Coated Oven Baked With Black Colour. , Table Bed Side - The Overall Size Of The Table Bed Side Shall Be 450Mm X 450Mm X 600Mm From Rear And 450Mm X 450Mm X 500Mm From Front As Shown In Drg. The Entire Frame Of Table Bed Side Shall Be Made Up Of 18Mm Ms Square Pipe 18 Gauge Duly Black Powder Coated. The Two Sides And Top Shall Be Made Up Of 18Mm Thick Mdf Board Exterior Grade. The Back Of The Table Except The Top Portion As Shown In Drg Shall Be Provided With 6Mm Commercial Plywood Bwr Grade Duly Screwed To Frame. The Two Sides Comma Back And Bottom Of Drawers Of The Table Shall Be Made Up Of 12Mm Thick Mdf Board Irrespective Of What Is Shown On Drg Comma Except The Front Side Which Shall Be Of 18Mm Thick Mdf Board Exterior Grade. The Drawers Shall Be Made Functional By Using Telescopic Channel Of Appropriate Size Shall Be Used For Smaooth Mvement Of Drawer.The Drawers Of The Tables Shall Be Provided With 100Mm Long Cp Handles. Rest All As Per Drg. The Lower Portion Of The Bed Side Table Should Be Box Type Provided With One Shutter Of Appropriate Size Duly Fixed With Piano Type Hinges Comma One Cp Handle Of 4 Inch Size And One Magnetic Catcher Should Also Be Provided. Rest All As Shown On Drawing And As Directed By Engr In Charge. , Bin Solied Linen Multi Purpose - Overall Size Shall Be Of 1000Mm Long Comma 380Mm Wide And 760Mm High. Bottom Rest Shall Be Made Of 19Mm Thick Mdf Board And Shall Be 900Mm Long And 280Mm Wide And 75Mm Hih Joined Together In Long And Short Sides. Multipurpose Bin Linen Shall Be Placed Over It. The Bin Shall Be 1000Mm Long Comma 380Mm Wide And 385Mm High. Back Side Shall Be Of 19Mm Thick Mdf Board 1000Mm Long And 685Mm High. Sides Shall Be Of 19Mm Thick Mdf Board 380Mm Wide And 685Mm High. Top And Bottom Shall Be Of 19Mm Thick Mdf Board 1000Mm Long And 380Mm Wide. A Vertical Partition Shall Be Provided At 400Mm From Inner Face Of Left Hand Side Which Shall Be Of 19Mm Thick Mdf. A Shelf Shall Be Provided In The Middle Of Left Portion Which Shall Be Of 19Mm Thick Mdf Board And Shall Remain Uncovered. Two Drawers And A Cupboard Shall Be Provided On The Right Hand Side. Of The Bin. Bottom Comma Sides Comma Back And Front Of Drawers Shall Be Of 12Mm Thick Mdf Board. The Partition Between The Drawers Shall Be Of 19Mm Thick Mdf Board. Front Shutter Of Cupboard Shall Be Hinged With Continuous Piano Type Hing And Shall Be Side Hung. The Shutter Shall Have Eight Vertical Slots Of 19Mm Width And 180Mm High With Gap Of 19Mm Made In The Center Of The Shutter. The Shutter Shall Be Provided With 100Mm Long Mild Steel Powder Coated Handle And Ball Spring Catch As Shown On Drawing. 19Mm Thick Mdf Board 543 Mm Long And 40Mm Wide Shall Be Provided As Base Support In The Front Under The Drawers. Teak Wood Bearers Two Numbers Shall Be Of 20Mmx20mm In Section And Fixed To Drawers. Teak Wood Bearers Two Numbers Shall Be Of 20Mmx20mm In Section And Fixed To Drawers On The Outer Sides In Such A Way That It Rns Smoothly Over The Beares Fixed On The The Sides Of The Partitions Of The Bin.