Tender For Construction Of 25 Mtr Span Motorable Bridge At Sair Galla Near Water Point Including Approaches Road.
Tender Value
5.02 Crore
Estimated cost
Bid Submission
04 Sep 2026
14 days left
EMD
10.04 Lakhs
Bank guarantee accepted
Document Fee
6000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Rajouri → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of 25 Mtr Span Motorable Bridge At Sair Galla Near Water Point Including Approaches Road.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. (All kinds of soil 50%, ordinary rock 30% & hard rock ( 20%) |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 3 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: (All kinds of soil 50%, ordinary rock 30% & hard rock ( 20%) |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 5 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. |
| 6 | All works above plinth level upto floor V level |
| 7 | Extra for providing richer mixes at all floor levels. Note:- Excess/ less cement over the specified cement content used is payable/ recoverable separately. Cement content considered in M-30 is @ 340 kg/cum |
| 8 | Add or deduct for using more or less cement in the items of design mix over and above the specified cement content therein. |
| 9 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 10 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 11 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 12 | Provoding and fixing Elastometric Bearing as per design and drawing bearing |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Cold twisted bars |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 15 | Foundations, footings, bases of columns etc. for mass concrete |
| 16 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 17 | Suspended floors, roofs, landings, balconies and access platforms |
| 18 | Columns, pillars, piers, abutments, posts and struts. |
| 19 | Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 20 | Edges of slabs and breaks in floors and walls 1 Under 20 cm wide |
| 21 | Supply and filling of Nallah Muck or second class quarry stones as filter media behind abuts etc. proper consolidated and all other carriage complete |
| 22 | Providing and fixing PVC rain water pipes conforming to IS: 13592 Type A including jointing for Weep holes 75 mm diametre |
| 23 | Stone filling hand packed including cost of stones in Horizontal on level |
| 24 | Providing and laying drain flooring / coping 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete |
| 25 | Providing and fitting Drainage spouts complete as per drawing and Technical specifications and as directed by the Engineer-in-Charge, including cost of carriage of all materials from approved source at site, with all leads and lifts and octori etc complete job (finished work to be measured) |
| 26 | Providing and laying of an elastomeric slab strip seal expansion joint catering to maximum horizontal movement upto 70mm, complete as per approved drawings and standard specifications to be installed by the manufacturer/ supplier or their authorized representative ensuring compliance to the manufacturers instructions for installation complete as per Technical Specifications and as directed by the Engineer-In-Charge, including cost and carriage of all materials from approved source to site, with all leads and lifts and ocjori etc. complete job (Finished work to be measured) as per technical specifications clause 1207. |
| 27 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Riveted and bolted |
| 28 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete On steel work |
| 29 | Providing and laying non-pressure of specified class R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete Non-pressure NP-3 class (Medium duty) R.C.C. pipes 900 mm dia. R.C.C. pipe |
| 30 | Consolidation of subgrade with power road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc.and rerolling the subgrade |
| 31 | Supplying and stacking of graded stone aggregate at site of size range. (Excluding Carriage) |
| 32 | 63 mm to 45mm |
| 33 | 53 mm to 22.4 mm |
| 34 | Supplying and stacking at site stone screening of size (excluding carriage) |
| 35 | 13.2 mm nominal size (Type A) |
| 36 | 11.2 mm nominal size (Type B) |
| 37 | Supplying and stacking at site stone dust (excluding carriage) |
| 38 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening /binding material to fill up interstices of coarse aggregate, watering and compacting to the required density |
| 39 | 63 mm to 45mm |
| 40 | 53 mm to 22.4 mm |
| 41 | Providing and applying tack coat using hot straight run bitumen of grade –VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleani preparing the existing road surface as per specifications. On W.B.M. @ 0.75 Kg/sqm. |
| 42 | Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge. 50 to 100 mm average compacted thickness with bitumen of grade VG-10 @ 3.5% (percentage by weight of total mix) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity |
| 43 | 2.5 cm premix carpet surfacing with 2.25cum and 1.12 cum of stone chippings of 13.2 mm and 11.2mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively including a tack coat with hot straight run bitumen including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately). With paving Asphalt grade VG-10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt |
| 44 | Providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete |
| 45 | Carriage of material by mechanical transport from source to the site of work including loading/unloading and stakcing complete. |
| 46 | Sand for an av. lead 107 Kms distance |
| 47 | Bajree/Stone aggregates below 40mm nominal size for an av. 47 Kms distance |
| 48 | Stone aggregate 63mm to 45mm size for an av.47 Kms distance . |
| 49 | Stone aggregate 53mm to 22.4 mm size for an av.47 Kms distance . |
| 50 | Stone screening for an av. 47 Kms distance . |
| 51 | Stone for an av.lead of 47 Kms distance. |
| 52 | Stone dust for an av.lead of 47 Kms distance. |
| 53 | 900 mm dia hume pipe for an av. Lead of 147 Kms Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysSep 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender