Tender For Repair To Security Fencing, Gate And Other Misc Works In Domestic Area Zone-Ii At Bhisiana Under Ge (Af) Bhisiana
Tender Value
45 Lakhs
Estimated cost
Bid Submission
05 Sep 2026
19 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Security Fencing, Gate And Other Misc Works In Domestic Area Zone-Ii At Bhisiana Under Ge (Af) Bhisiana
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles in any description and removing/disposal off from the site to outside MOD land complete all as specified and as directed. |
| 2 | Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 3 | Material and labour for brick work in half brick thick wall straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge. |
| 4 | Material and labour for 25mm thick precast cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in louvers and jallies (measured solid) including all moulding frame (Pre cast frame) and set in cement mortar (1:6) including necessary form work complete all as specified and as directed. |
| 5 | Taking down cement plaster/rough cast plaster from brick walls/soffits of roof projections & chajjas /ceilings etc. including racking out joints, hacking for key & scrubbing down with water etc including disposal of rubbish material to any distance out side MOD land complete all as specified and as directed. |
| 6 | Material and labour for 15mm thick cement plastering/ rendering in cement mortar (1:4) on any face of Brick walls or concrete surfaces, finished even and fair complete all as specified and as directed. |
| 7 | Material and labour for rough cast plaster on exterior walls in two layers, under layer not less than 10mm cement plaster (1:3) (1 cement: 3 coarse sand ) furrowing the under layer with scratching tool, and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of (1: 1: 1) shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered, complete in all respects and as specified and directed by the Engineer-in-Charge. |
| 8 | Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down or by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash by using paint brush complete all as specified and as directed. |
| 9 | Material and labour for preparation of plastered surfaces of walls/pillars /cornices (on new surface or old prepared surface after complete removal) by brooming down with using broom/sand papering or by any other mean, washing down with water and applying two coats of cement base paint as per approved tint/colour with using paint brush complete all as specified and as directed. |
| 10 | Material and labour for preparation of new steel and iron surfaces of any description, not otherwise described, exceeding 10 cm in width or girth, including cleaning the surface free from dust, dirt, grease, oil and other foreign matter and surface imperfections by rubbing down with emery paper/sand paper or by other approved means to obtain a clean, smooth and even surface and further applying one coat of red oxide zinc chromate primer and two coats of first-quality synthetic enamel paint of approved brand, shade and tint, each coat applied by brush only after proper preparation and complete drying of the preceding coat, to produce a smooth, uniform, durable and aesthetically acceptable finish, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 11 | Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels, cills, steps; seismic and other similar bands complete all as specified and as directed.(NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of BOQ. |
| 12 | Material and labour for mild steel TMT bars, grade Fe 500D/550D, 6 to 8 mm dia cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.(NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.) |
| 13 | Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15cm thickness below or above ground level of any description and in any position and including disposal of rubbish material to any distance out side MOD land complete all as specified and as directed. |
| 14 | Dismantling of interlocking tile/paver block/brick/chequered tile etc including kerb stone (laid flat or on edge etc) laid dry or pointed complete all as specified and as directed. |
| 15 | Material and labour for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and as directed |
| 16 | Material and labour for 40mm thick cement concrete (1:2:4), Type-B-1 , using 20 mm graded stone aggregates as in floors, pavement, hardstanding and finishing the surface of concrete topping even and smooth (without using extra cement) complete all as specified and as directed. |
| 17 | Material and labour for 75mm thick cement concrete ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed. |
| 18 | Material and labour for 20 mm thick bedding layer in cement mortar (1:6) in grey cement, and finish the surface even and fair/rough to receive the tile complete all as specified and as directed. |
| 19 | Material and labour for providing and laying chequered cement concrete tiles of size 200mm × 200mm × 25mm thick, manufactured by the table vibratory method using PU/rubber moulds, made from cement, graded aggregates, grey cement with approved mineral pigments, having approved pattern and texture, laid as in floors, footpaths, walkways and similar locations. The tiles shall be laid true to line, level and required slope, set and jointed in neat cement slurry at the rate of 3.00 kg per square metre, over the prepared bed/sub base (sub base bed measured and paid separately), filling joints with white/grey cement mixed with matching pigment, complete in all respects, as specified and directed by the Engineer-in-Charge. |
| 20 | Supply and laying/fixing 60mm thick factory made chamfered edge cement concrete paver block/ interlocking tile of M-35 grade, prepolished & preglazed, with approved colour, design & pattern (laid in required colour & pattern as directed) as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand, finishing and sweeping extra sand complete all as specified and as directed. |
| 21 | Supply and laying at or near ground level factory made kerb stone of M-20 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed. |
| 22 | Material and labour for Dismantling/taking out old paver block/ interlocking tile of any description and in any position, making surface leveled as per site requirement and refixing/laying the same over and including 30mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand, finishing and sweeping extra sand complete all as specified and as directed. |
| 23 | Dismantling of stone slab tiling including cement mortar bedding ( but not backing) and including removing rubbish material from building and thrown in low lying empty area at any distance as direccted from the site complete all as specified and as directed by Engineer-in-Charge. |
| 24 | Material and labour 16-18mm thick Granite stone slab (thappi) in approved shade (like dark black, mahroom etc), machine cut, duly factory grinding and polishing (table rubbed and polished), as in steps, jams, pillars, window cill or similar locations where directed, set & jointed in and including neat cement slurry, laid over and including 15mm thick cement mortar (1:4) screed bed, and pointing in white cement mixing with pigment to match with shade of slab, including cutting, dressing, edge finishing, rounding of exposed edges where required, including cleaning and extra polishing if required complete all as specified and as directed.Note : (i) Single piece should be used in steps/jambs, equal to width. |
| 25 | Material and labour for providing and fixing machine-cut Kota stone slabs, 16–18mm thick (minimum), of approved quality, colour and shade, Kota stone size of slab not less than 550x500mm, as in flooring, cut to the required size and shape, dressed true, set and jointed in position over and including a 15mm thick cement mortar (1:4) screed bed, laid to the required line, level and slope, with neat cement slurry. The work shall include cutting, dressing, trimming, machine finishing, forming mitred joints where required, pointing joints with white cement mixed with suitable matching pigment to match the colour and shade of the stone, rubbing, grinding and final polishing by machine/hand-held polishing machine to produce a smooth, even and lustrous finish, complete in all respects, as specified and directed by the Engineer-in-Charge. |
| 26 | Dismantling iron or mild steel work of any description not otherwise provided for including doors, gates, walkways, railing, framed work, parking shed normal height etc, complete all as specified and as directed. |
| 27 | Material and labour for mild steel framed structural work comprising angle iron vertical posts, columns, main beams, cross beams, rafters, purlins, bracings, tie members, frames for sunshades/chajjas, parking sheds, canopies, platforms, walkways, steel gate and other similar works, fabricated from rolled mild steel joists, channels, angles, tees or other rolled steel sections, together with gusset plates, base plates, cleat plates, rails, braces, round bars, stiffeners and other connecting plates, conforming to Grade Fe-410-W (Grade E-250 Quality A). The work shall include cutting, bending, notching, coping, drilling, punching, shaping, edge preparation, welding, grinding of welds, fabrication, shop assembly, transportation, erection, alignment, plumbing and fixing in position with approved holding-down bolts, anchor fasteners, nuts, bolts, washers and all necessary fixing accessories. The item shall include all labour, materials, welding electrodes, gas cutting, scaffolding, staging, lifting arrangements, tools and plant, consumables, safety measures and all incidental works necessary for satisfactory completion of the work at all locations up to a height of 5.00 metres above the existing ground level or any accessible roof, floor, platform or balcony level, complete in all respects, as specified and directed by the Engineer-in-Charge. |
| 28 | Material and labour for providing and fixing Stainless Steel work (Grade 304) comprising railings, gates, handrails, balustrades, grills and similar fabricated works, manufactured from stainless steel hollow circular, square or rectangular tubes, channels, angles, flats, plates, knobs, caps and other required sections of approved size and thickness.The work shall include cutting, bending, curving, notching, drilling, punching, shaping, welding by TIG/MIG process, grinding, dressing of welds, buffing, all exposed stainless steel surfaces shall have a No. 4 Satin Finish or Mirror Finish, fabrication, shop assembly, transportation and fixing in position with approved stainless steel nuts, bolts, screws, washers, dash fasteners, anchor fasteners, hinges, locking arrangements, handles, stoppers, tower bolts, sliding door bolts, stay holders, guide brackets, base plates, cover plates and all other necessary stainless steel fittings and accessories, complete in all respects, as specified and directed by the Engineer-in-Charge.Notes:(i) Measurement for payment shall be made in Kilograms (kg) based on the actual weight of stainless steel work fixed in position.(ii) The weight of the stainless steel sections or complete fabricated gate/railing shall be physically ascertained by a Board of Officers (BOO) constituted by the Garrison Engineer before incorporation in the work, and payment shall be made on the basis of the actual weight so determined. |
| 29 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, in roof coverings, stacking serviceable sheet for re use if directed and balance removing from the site complete all as specified and as directed. |
| 30 | Material and labour for Providing and fixing pre-painted galvalume hot-dip aluminium–zinc alloy metallic coated corrugated steel sheets (profiled) of any approved profile/pattern, 0.50 mm thick (BMT), coating class AZ150, conforming to IS 15965:2012, durability class 3 and atmospheric classification category C3, factory pre-painted in an approved colour and having a minimum yield strength of 550 MPa. The sheets shall be used for roof covering, chajjas, and shall be fixed to the existing/proposed supporting structure with approved self-drilling screws complete with suitable corrosion-resistant washers, including all necessary end and side laps, cutting, bending, folding, drilling, fitting, alignment, levelling and making good. The item shall also include all necessary scaffolding, staging, ladders, working platforms, lifting arrangements, tools, tackles and safety/fall-protection measures required for execution at any floor level or height, complete, all as specified and as directed. |
| 31 | Dismantling chain link/wire mesh fencing of any type and thickness including flat iron and line wires/round bars complete all as specified and as directed by Engineer-in-Charge. |
| 32 | Dismantling galvanized steel barbed wire fencing comprising any number of strands of galvanized steel barbed wire fixed horizontally, vertically or diagonally to swan necks (Y-type horns), angle iron posts, tubular posts, rails, poles or any other supporting members, including cutting binding wires, removing G.I. staples, steel pins, clips and other fixing accessories, lowering carefully without damage as far as practicable, and removing complete with all rubbish and debris arising out of the dismantling operation, complete in all respects, as specified and directed by the Engineer-in-Charge.Notes:(i) Measurement for payment shall be made in 100 RM for each individual line of barbed wire actually dismantled. Each individual line of barbed wire shall be treated as one unit of measurement, irrespective of the number of stranded line wires forming that line.(ii) Each horizontal, vertical or diagonal line shall be measured separately between the centre lines of end supports. No separate measurement or payment shall be admissible for laps, joints, cutting, untying, removal of binding wire, staples, clips, steel pins or other fixing accessories. |
| 33 | Dismantling of post or struts (RCC) any section incl taking out embeded portion and making good disturbed ground embeded in concrete, complete all as specified and as directed. |
| 34 | Excavation in post holes in soft/loose soil n. exc 0.50 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm including removing of surplus spoil to a distance n exc 50 mtr and making good the disturbed surfaces all as specified and directed by Engineer-in-Charge. |
| 35 | Material and labour for mild steel fencing work comprising angle iron fencing posts, end posts, corner posts, struts, intermediate posts, stays, braces, flat iron fillets, cleats and other ancillary members, fabricated from steel conforming to Grade Fe-290 (Grade E-165), complete with provision of swan neck (Y-type horn) where directed for barbed wire/security wire. The work shall include cutting, bending, notching, drilling holes for fixing barbed wire, chain link wire mesh, cutting and shaping tops, welding, riveting, bolting, grinding of welds, fabrication, shop assembly, transportation and erection in true line, level and plumb, complete all as specified and directed by the Engineer-in-Charge.Notes: (i) Measurement for payment shall be made in Kilograms (kg) based on the actual weight of mild steel work fixed in position.(ii) Cement concrete foundations, excavation, backfilling and disposal of surplus excavated earth and painting work shall be measured and paid separately under respective item of BOQ. |
| 36 | Material and labour for PCC (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in foundation filling, in post hole, bed block, around the poles/stay, coping/Pedestal of pole, etc & similar work including necessary form work, finishing the exposed surfaces of the concrete even & smooth without using extra cement, complete all as specified and as directed. |
| 37 | Supply and fixing galvanized steel barbed wire fencing comprising two strands of galvanized steel line wire of 2.24mm diameter, barbed with 2.00mm diameter galvanized steel point wire having barbs at 75mm centres, conforming to the relevant Indian Standards, stretched taut and securely fixed to swan necks (Y-type horns), angle iron posts, tubular posts, rails, poles or any other supporting members, laid horizontally, vertically or diagonally, as directed. The work shall include straining the wire to the required tension, lapping where necessary, securing the wire with galvanized iron binding wire, G.I. staples, steel pins, clips or approved fixing accessories at all supports and intersections, tying at crossings wherever directed, maintaining proper alignment and uniform spacing, and all cutting, jointing, complete in all respects, as specified and directed by the Engineer-in-Charge.Notes: (i) Measurement for payment shall be made in 100 RM for each individual line of barbed wire actually fixed in position. One line consisting of two stranded line wires with barbs shall be treated as one unit of measurement.(ii) Each horizontal, vertical or diagonal line shall be measured separately between the centre lines of end supports. Laps required for proper jointing, binding wire, staples, clips, steel pins and other fixing accessories shall be deemed to be included in the quoted unit rate. No separate payment shall be admissible on this account. |
| 38 | Supply only chain link mild steel galvanised fencing (woven in diamond mesh pattern) complete all as specified and as directed.Note : The weight of the chain link fencing shall be physically ascertained by a Board of Officers (BOO) constituted by the Garrison Engineer before incorporation in the work, and payment shall be made on the basis of the actual weight so determined. |
| 39 | Supply only galvanized mild steel chain link fencing, machine woven in 50mm × 50mm diamond mesh pattern, fabricated from 3.00mm diameter galvanized steel wire, uniformly PVC coated in green colour or other approved shade, conforming to the latest editions of IS 2721 and IS 4826, of approved make and quality, complete with all manufacturing tolerances, free from kinks, broken wires, excessive joints or other manufacturing defects, supplied in standard rolls or required lengths, complete in all respects, as specified and directed by the Engineer-in-Charge.Notes:(i) The weight of the chain link fencing shall be physically ascertained by a Board of Officers (BOO) constituted by the Garrison Engineer before incorporation in the work, and payment shall be made on the basis of the actual weight so determined. |
| 40 | Fixing only galvanized mild steel chain link fencing of any mesh size, to angle iron posts, RCC posts, rails, flat iron fillets or any other supporting framework, including stretching the chain link fabric to the required tension, aligning and fixing in position with round bar/GI line wires (tying wires), nuts, bolts, washers, clips or other approved fixing arrangements, and including providing not less than 1.20mm diameter galvanized iron binding wire for tying and securely fastening the chain link fencing to the supporting members at the required spacing, complete in all respects, as specified and directed by the Engineer-in-Charge.Notes:(i) Supply of chain link fencing, galvanized iron line wire (tying wire)/round bars, flat iron fillets (where provided), nuts, bolts, washers shall be measured and paid for separately under the respective BOQ items.(ii) The cost of galvanized iron binding wire, including cutting, tying and securing the chain link fencing to the supporting framework, shall be deemed to be included in the quoted unit rate. No separate payment shall be admissible on this account. |
| 41 | Supply only mild steel screw bolt (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5cm, and Diameter of neck 5 to 10 mm, complete all as specified and as directed. |
| 42 | Supply only Plain GI wire, galvanised class 3, 4mm dia as line wire (tying wire) complete all as specified and as directed. |
| 43 | Excavating and removing silt, mud, sludge, and other deposited material from storm water drains of average girth 280 cm, where the depth of deposited silt/mud varies from 5 cm to 20 cm with an average depth of 12.5 cm, including deposits lying unevenly on the bottom and side walls of the drains. The item shall also include removal of all grass, bushes, weeds, undergrowth, small shrubs, and other vegetative growth from the bottom and sides of the drains including collection, loading, transportation, and disposal of all excavated silt, rubbish, vegetation, and other waste material obtained from drain cleaning to an approved dumping area at a lead exceeding 500m, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 44 | Net CONTRACT SUM will be worked out in General Summary after deduction of ‘CREDIT SCHEDULE’ amount inserted by MES. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender