Tender For Repair And Maintenance To Kitchen, Bathroom And Connected Items In Offrs Md Accn In Bairagarh Under Ge Bhopal
Tender Value
30 Lakhs
Estimated cost
Bid Submission
04 Sep 2026
11 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bhopal → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Maintenance To Kitchen, Bathroom And Connected Items In Offrs Md Accn In Bairagarh Under Ge Bhopal
BOQ
| Sl. No. | Item Description |
| 1 | Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below.(ii) Amount of Schedule of credit shall be deducted offline |
| 2 | M&L for 15mm thick rendering in CM 1:4 faces of brick or concrete surfaces (external surfaces) mixed with water proofing compound @ 3% by wt of cement , finished fair, even and smooth without using any extra cement including taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description.complete all as specified and directed. Note :- Water Proofing compound shall be measured and paid seperately.Note :- Rate is inclusive of scaffolding upto height of 12 m. |
| 3 | M&L for 10mm thick rendereing brick or concrete surface in CM 1:6 finishing the surface fair & even without using extra cement including taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description, complete all as specified and directed. |
| 4 | Integral water profing compound mixed with cement mortar, complete all as specified and directed. |
| 5 | Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces, complete all as specified and directed. |
| 6 | M&L for applying one coat of white wall putty 1mm thick on walls complete all as specified and directed. |
| 7 | M&L for dampness rectification on wall and roof Area :- Surface Preparation: Removing existing putty/plaster/POP surface from the affected wall with wire brush/grinder/hammer etc up to brick level, filling of crack fill paste in visible cracks and apply two coats of DAMP STOP ELASTO (MAKE : BERGER) over finished surface. Necessary scaffolding suitable for height upto 10 mtr from average ground level, complete all as specified and as directed. |
| 8 | M&L for complete removal of existing treatment on wall (Internal/External) /chajjas/roof projections including facias, cornices etc by scrapping with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc) & (External surface by washing/cleaning down with water) by skilled labour including filling holes, cracks, depressions of scraped surfaces with putty and preparation of surfaces for further treatment. Necessary scaffolding suitable for height upto 10.00 mtr from average ground level, complete all as specified and directed. |
| 9 | M&L for applying Two coats Exterior weather proof emulsion paint of including complete removal of existing treatment. Necessary scaffolding suitable for height upto 10.00 mtr from average ground level complete all as specified and directed.(Make :- Asian - Apex ultima, Berger long life 10, Dulux - Weather shield.) |
| 10 | All as per item No. 8.00 here-in before but One coat of Exterior weather proof emulsion paint on old prepared wall surfaces incl chajjas, patta etc. surfaces, complete all as specified and directed. |
| 11 | M&L for applying One coat of oil bound distemper emulsion on old prepared wall surfaces including window & door jambs, cills, cornices etc. having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete all as specified and directed.(Make : Asian- Tractor emulsion spark, Berger distemper, Nerolac-Little Master(Beauty). |
| 12 | All as per item No. 10.00 here-in before but Two coats of oil bound distemper emulsion on old prepared wall surfaces including window & door jambs, cills, cornices etc. complete all as specified and directed. |
| 13 | M&L for preparatration of old decorated surfaces of ceiling including brooming, scraping down smoke spot, moulds, moss , effloresecent salts trading oil, greasy spots and stopping nails marks and applying One coat of oil bound distemper emulsion having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour, complete all as specified and directed. |
| 14 | Dismantling structural steel work including purlins,tursses,etc. complete all as specified and directed. |
| 15 | Dismantling of timber scantling in fillets, rails, posts, rafters, purlins etc 40 sqcm and over in section, in any posotion for unframed works, complete all as specified and directed. |
| 16 | S&F steel work in tubular/angle trusses including special shaped washers, purlins, rafters, posts etc complete all as specified and directed. |
| 17 | M&L Pre Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick AZ-150 of an colour having tensil strength of 550/MPA as in roof covering/cladding to wall/ ridge,fixed with self tapping screw/L type or J type cranked hook bolts including dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering, complete all as specified and directed. |
| 18 | M&L Pre Galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick AZ-150 of an colour having tensil strength of 550/MPA as in roof covering/cladding to wall/ ridge,fixed with self tapping screw/L type or J type cranked hook bolts including dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering, complete all as specified and directed. |
| 19 | M&L granite 16-18 mm thick (of any type) work (machine cut) in steps, jambs, pillar, window-cills, cooking platform and like in 15 mm thick cement mortar (1:4) including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed bed in CM 1:4 including dismantling of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar, complete all as specified and directed. |
| 20 | M&L for rounding to edges of stone one edge such as in steps,cooking platform and other similar situation complete all as specified and directed. |
| 21 | M&L for non skid ceramic coloured tiles 7mm to 8mm thick (square /rectangular ) area of each tile exceeding 0.11 sqm , but not exceeing 0.18 sqm , in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles including dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises, compelte all as specified and directed. |
| 22 | M&L for glazed tiles , coloured 300x450 x 6 to 7 mm thick as in skirting/dado over & including 10mm thick rendering in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement including dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises complete all as specified and directed. |
| 23 | M&L for water proofing treatment to sunken surfaces of slab including in following sequence complete :- (a) Slope correction providing PCC 1:1.5:3 (using 12.5mm graded stone aggregate), average thickness 25mm , mixed graded stone aggregate , average thickness 25mm , mixed with integral water proffing compound \\"DITCHTMENT DM' manufactured by Dr fixit Pidiproof LW + of M/s Pidilite Industries or STP No 1 (Liquid) of M/S STP Ltd as approved by GE , in proportions as suggested by manufacturer. (b) Applying evenly a priming coat of bituminous primer confirming to IS 3384 @ 0.7 Kg per Sqm on prepared surfaces. (c) Applying evenly a coat of hot blown bitumen grade VG-10 @ 1.5kg/sqm on the primer surfaces. (d) Laying 150 micron thick black polythence film on the suface with 10mm overlaps sealed and bounded the surface. (e) Applying evenly a coat of hot bown of grade 85/25 @ 1.5 kg per sqm on the surfaces. (f) 48 hrs testing of treatment for water thightness by ponding of water.Note:- Rates including demolition of existing suken slab and concrete complete all as specified and directed, |
| 24 | S&F 16 mm CPVC pipes SDR 11 and plain CPVC SDR 11 with all necessary fittings and fixed complete to wall and ceiling or laid in floors including taking down exiting tubing, complete all as specified and directed. |
| 25 | S&F 20 mm CPVC pipes SDR 11 and plain CPVC SDR 11 with all necessary fittings and fixed complete to wall and ceiling or laid in floors including taking down exiting tubing, complete all as specified and directed. |
| 26 | S & F in repair for designer bevelled edge frameless looking mirror of selected quality glass of min 6mm thick fixed on wall with screws in any size complete all as specified and directed |
| 27 | S&F in repairs 15 mm pillar taps, fancy type , cast copper alloy, chromium plated, screwed down high pressure, with or without lettered \\"Hot or Cold\\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 28 | S&F in repair 15 mm Bib taps, chromium plated , screwed down, screwed for iron pipe or for brass ferrule and fixing complete all as specified and directed. |
| 29 | S&F in repairs 15 mm bore Bib taps, long body fancy type cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferulle and fixed complete as specified. |
| 30 | S&F in repairs 15 mm stop/angle valves, cast copper alloy, chromium plated screwed down high pressure, with crutch or butterfly handle, scrwed both ends for iron pipe or for unions and fixing complete all as specified and directed. |
| 31 | S&F in repair 15mm dia brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 32 | S&F in repair brass chromium plated shower rose 125mm in size with or without swivel joints any size including fixing to steel pipe or union , complete all as spfecified and directed. |
| 33 | S&F in repairs 20 mm (curtain rail) mild steel chromium plated facy type with fixing brackets, stops, rollers etc complete all as specified and directed. |
| 34 | S&F 100mm hasp and staple, safety type, anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 35 | S&F repair 40mm dia cupboard/kitchen cabinet knobes fixed with nuts, screw and washer of MS, bright finshed, complete all as specified and directed. |
| 36 | M&L for fabricating and fixing powder coated (minimum 50 miciron) aluminium sections of required size for doors, windows any type, frames and partitions including aluminium hinges of required size jointing cleats, screws salsh fasterners , plug for fixing with walls, column etc including taking down damage portion of damage door, windows or taking down complete door/ window complete all as specified and directed. Note :- Rates are inclusive of necessary new fitting for door/ window i.e handle, tower bolt, butt hinges etc complete. |
| 37 | M&L framed work such as grills, gratings, gate etc with ends of bars souldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railing, frame work of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified and directed. |
| 38 | S&F 4.8 mm thick plain glass and glazing with putty /UPVC beading including rubber packing, fixing glass to UPVC surrounds complete all as specified and directed. |
| 39 | S&F for stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to UPVC door with beading complete all as specified and directed. |
| 40 | S&F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to UPVC door with beading complete all as specified and directed. |
| 41 | S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and directed. |
| 42 | S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels incliduing hacking out old broken glasses complete all as specified and directed. |
| 43 | Taking down chowkhats or frame with shutter n.exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 44 | S & F solid PVC door frame of size 50 mmx 47mm made out of 5 mm plain colour PVC sheet reiforced with MS square tube and fixing in opening as per manufacturer instruction complete all as specified and directed. |
| 45 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement including 100 mm aluminium butt hinges 03 Nos,Aluminium Handle-02 Nos, aluminium tower bolt 150 mm -01 No and alumiium sliding door bolt 150 mm - 01 No. complete all as specified and as directed. |
| 46 | Taking down door shutter any description exc 1.0 sqm but n.exc 2.00 sqm each complete all as specified and directed. |
| 47 | M&L for 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, including 100 mm MS butt hinges 03 Nos, SS Handle-02 Nos,, SS tower bolt 150 mm -02 No and SS sliding door bolt 250 mm - 01 No and applying. two coats of synthetic enamel paint over one coat of pink primer over 10cm width or girth on wooden surface including preparation complete all as specified and as directed. |
| 48 | S&F 2nd class wood 30mm thick glazed and skelton shutter open rebeted and prepared to receive glass gauge etc(with sash bar) edges of framing plain champhered or rounded fitted with cut and mitred beads for securiing glass including 100 mm SS butt hinges 03 Nos, SS Handle-02 Nos,SS tower bolt 150 mm -01 No and SS sliding door bolt 250 mm - 01 No. and applying. two coats of synthetic enamel paint over one coat of pink primer over 10cm width or girth on wooden surface including preparation complete all as specified and as directed. |
| 49 | M&L for preparation new steel & iron surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over and including a coat of red oxide zinc chrome primer, complete all as specified and directed. |
| 50 | M&L for two coats of synthetic enamel paint over one coat of pink primer over 10cm width or girth on wooden surface including preparation complete all as specified and directed. |
| 51 | S&F in repair 32mm bore PVC waste pipe for kitchen sink /WHB one mtr long complete all as specified and directed. |
| 52 | S&F in repair 100mm dia CP grating (minimum weight 25gms) all as specified. |
| 53 | S&F in repair PVC connection 15mm size PTMT nuts of length 600mm all as specified. |
| 54 | S&F in repair vitreous china squanting pan \\"Orissa\\" pattern size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) including cement concrete bedding, complete all as specified and directred. |
| 55 | S&F vitreous china oval shaped cunter top wash basin, white , flat back, Size 550x400mm / std size including waste pipe , coupling, PVC pipe connection 15mm dia 600mm long, complete all as specified and directed. |
| 56 | S&F China wash down water closet pan (Pedestal Pattern), white , pedestal pan and 'P' or 'S' trap , plastic water closet seat , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 57 | S&F in repair Vitreous China Wash Basin, white , flat back, Size 630x450mm including brackets, waste pipe , coupling, PVC pipe connection 15mm dia 600mm long complete all as specified and directed. |
| 58 | S&F in repairs PVC low level flushing cistern 10 ltrs capacity with all internal fittings including 32mm dia flush pipe and fixing to supply pipe including PVC connection 600 mm long 15 mm bore with brass heads & washers with connections fixed in repairs complete all as specified and directed. |
| 59 | S&F in repair health faucets CP with 1.2mtr long CP flexible pipe complete all as specified and as directed. |
| 60 | S&F in repair EWC seat cover white/coloured plastic with fixing bolts & hinging device complete ISI marked all as specified and directed.(make commander/Parryware/Cera) |
| 61 | S&F in repairs PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints laid in trenches , floors or fixed in walls complete all as specified and directed. |
| 62 | S&F PVC (SWR) 110mm bore bends any radious complete all as specified and directed. |
| 63 | S&F PVC (SWR) Junction (Single T) 110mm bore equal or unequal complete all as specified and directed. |
| 64 | M&L for brick work with sub class B bricks straight or curved on plan exc 6 m mean radius, built in CM 1:6 including demolition of brickwork or stone/boulder masonry , built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings dressed stonework and precast articeles, all as specified and directed. |
| 65 | S&F in repair Floor door stopper 150mm long of aluminium ally body and tonge , anodised , with hard drawn steel spring, fixed in floor complete all as specified. |
| 66 | M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation , filling, subbase and mass including demolition of cement concrete in floors and pavings not exc. 15 CM thickness (below/above ground level) including floor finishes concrete, complete all as specified and directed. |
| 67 | M/L for 75 mm thick PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) in plinth protection, approns, hard standing, path and like including bitmuminous mastic filling in 1:3 joints (in every 3.00mtr) and finishing the surfaces even and smooth without using extra cement including demolition of cement concrete in floors and pavings not exc. 15 CM thickness (below/above ground level) complete all as specified and directed. |
| 68 | M&L for Heavy duty flooring tiles , harsh weather & UV resistance, high abrasion resistance, MOH hardness >6 thickness 10 mm thick , area of each tile not less than 0.09 sqm , anti slip type laid in floors , steps, edges etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15 mm thick rendering in CM 1:4 and dismantling of exiting tiles complete all as specified and directed. |
| 69 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. |
| 70 | M&L for precast cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in cover slab for manholes etc set in CM 1:4 including demolition of existing cover slab, complete all as specified and directed. |
| 71 | M&L for vitrified ceramic tile light shade 8-10 mm thick (square /rectangular) polished, area of each tile not exceeding 0.36 Sqm as in floors/skirting over and including 15mm thick screed bed in CM 1:6 etc and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the permises complete all as specified and directed. |
| 72 | M&L for vitrified ceramic tile light shade 8-10mm thick (Square /rectangular ) polixhed , area of each tile not exceeding 0.36 sqm on vertical surfaces such as skirting dado and risers to steps etc over & including 10mm thick rendering in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to match including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the permises complete all as specified and directed. |
| 73 | M&L in repairs 18/19 mm thick ply boards for chowkhat, cupboard, grade 2 quality, interior grade, commercial type,decorative face with 0.9mm thick mica for lipping/frame to match on both faces fixed with screws to timber frame-work, fixed with screws/nails to timber frame work complete all as specified and directed. |
| 74 | S&F 150 mm Aluminium handles, D type base plate, anodised complete all as specified and directed. |
| 75 | S&F in repairs 12 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and directed. |
| 76 | S&F decorative laminate 0.9 mm type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed. |
| 77 | supply and fixing factory made 18mm both side laminated HDHMR board in modular kitchen carcasse made of mini fix joint with 1mm same colour edge banding including fixed with nut, screws and washers fevicol, nails complete all as specified and directed. Make -: Action Tesa , Greenply or equivalent |
| 78 | S&F fixing factory made 18mm acrylic HDHMR board in modular kitchen shutters with 1mm same edge bending on edges for kitchen cabinets/cupboards etc. including fixed with nut, screws, washers, nails all as specified and directed. Make -: Action Tesa , Greenply or equivalent |
| 79 | S&F powder coated stainless steel SS 304 sensys intergrated soft cose hinges having size 103x64mm finish of nicle/silver complete all as specified and directed. |
| 80 | M&L for provn of water proofing roof treatment to non accessible /accesible RCC roof with APP modified membrane with non woven polyster reinforced wt not less than 3 Kg/Sqm of thickness not less than 3 mm having thermal; insulation with white or plain finish on upper side of membrane uniformely embedded during manufacturing process including taking down existing treatment all as per following specifications:-(a) 10 mm thick plaster in CM 1:4 mixed with and including water proofing compound @3% by weight of cement applied over roof slab. After the plaster is cured the roof will be tested for water tightening by ponding with water for 72 Hrs for any seepage / leakages etc. if any seepage is oberved the rectification will be carried out by pressure grouting under the pressure of 5 Kg/Sqcm using cement based cement grout. After the surface is repired the slab will be tested for watertightness against before processing further treatments. (b) The surface of the roof, parapet and gutters, drain mouths etc. over which water proofing treatment is to be applied shall be cleaned of all foreign matters such as fungus, mass, dust etc. by wire brushing and dusting. For cast iron drain outlets the groove shall be cut around to tuck in the treatment as pipes, chimney stacs etc. and other similar situations to ease up about corners.(c) Hot blown bitumen VG-10 as in primer conforming to IS : 3384-1965 @ 0.30 Kg/Sqm to be applied on prepared surface till the surface is properly impregnated.(d) APP modified water proofing membrene as specified shall be laid by torch application method laid on hot bitumen 85/25 grade (bonding material) at the rate of 1.2 kg/sqm primer surface as per manufacturers instructions, The overlaps while torching shall be 100 mm in both directions (longititudinal and transverse directions). All overlap joints shall be sealed throughly by thermofusing both the membrene layers and sealing it with the help of hot trowel. The overlap joints shall be made as monolithic layer. (e) All joints & changes in direction should be curved with cement morar 1:3 mixed with SBR latex @ 200 ml per beg of cement and cured well before laying the membrane.(f) A fillet of PCC (1:2:4) type B-0 of 100 mm x 100 mm shall be provided at all junctions of vertical and horizontal surfaces and wherever there is a change of direction. The membrane should not be taken over at any steep turns and hence all corners /junctions should be rounded. |
| 81 | Deduct Schedule of credit (calculation will be done off line) Rs. 22840.00 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender