Tender For Miscellanious Civil & Electrical Work (Stp, Wtp, Fire Fighting, External Electrical, Kitchen Equipment, Furniture And Fountain Work For Working Women Hostel At Fulsung & Transit C Rudrapur
Tender Value
22.22 Crore
Estimated cost
Bid Submission
29 Aug 2026
5 days left
EMD
44.45 Lakhs
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udam Singh Nagar → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Miscellanious Civil & Electrical Work (Stp, Wtp, Fire Fighting, External Electrical, Kitchen Equipment, Furniture And Fountain Work For Working Women Hostel At Fulsung & Transit C Rudrapur
BOQ
| Sl. No. | Item Description |
| 1 | External Electrical Works |
| 2 | HT Metering Panel (SEB's) Supplying / Receiving, Installation, Testing and Commissioning of Powder coated, 14 SWG CRCA sheet steel enclosed 11KV H.T. Metering Panel complete with the following: 1set of 11/ √3KV / 110/ √ 3 Volt, 100 VA burden & accuracy class 0.5, single phase construction, dry type cast resin PT. 3 Nos. of dual core 50/5A, 15 VA burden, accuracy class CL 0.5, 11 KV cast resin CTs One Set of Phase Indicating Lamps. ,2 Sets of HRC fuses with fuse base (H.T. Fuse - 1A & LT fuse 2-6A). 2 Nos. indoor cable end box suitable for 3C x 240 sq.mm. 33 KV(E), aluminium conductor XLPE Ar. cable (Incoming & Outgoing cable).1 No. SEB approved digital Trivector meter with MDI in KVA of accuracy class - 0.5.(Accuracy class shall be as per local board) Note: The contractor shall get the Trivector meter, CTs' & PT tested by SEB and the charges for liasioning for the same will be paid extra. SITC Rate for Metering Panel as described above Note: The contractor shall ensure that the above panel meets the requirement as insisted by State/Local authorities(As per SEB) for satisfactory operation and as per the Drawings |
| 3 | 11kV 2 POLE STRUCTURE Supply,installation,testing and commissioning of two pole structure with required arrangement for terminating 11KV overhead conductor on one side and 11KV, 2R x 3 x 300 sq.mm. Al conductor XLPE cable on the other side including providing triple pole ,mechanically operated mounted on insulators and steel frame with operating mechanism worked from ground level,expulsion fuses of 33KV ,required rating along with 11KV 200 amp air break isolator suitable for outdoor application ,earth switch, Metal oxide type Lightning arrester complete with all fittings and discharge capacity 50 KA complete as required. 11 kV HT 'H' pole as per specification & as described above |
| 4 | SITC of 11kV Compact Sub-Station Design, fabrication, assembling, wiring, supply, testing at works, packaging, forwarding to site and supervising the testing & commissioning of 11kV compact secondary substation suitable for Outdoor installation with natural cooling, having type tested equipments comprising of oil-type distribution transformer and SF-6 insulated compact switchgear enclosed in robotically sealed stainless steel tank, low-voltage switchboard, interconnection between HT switchgear and transformer using cables and transformer to LT-switchgear using aluminium busbars, factory built ready for connection type, internal GI earthing provided complete with other associated equipments etc. complete as required conforming to IEC 62271-202 and relevant IS or international specifications, as regards to design, manufacturing, type-testing, routine-testing and operator safety (IAC AFLR). The enclosure shall have modular construction using G.I. Sheet and shall be powder-coated from exterior. The Transformer compartment will have IP-23 ingress protection, whereas the HT/LT compartment will have IP-54 protection. The 11kV Outdoor Compact Sub-Station shall be consisting of following , HT SWITCHGEAR 11kV 630Amps 20kA for 3 sec. & tested for 20kA/ 1 sec internal arc , SF6 insulated Non-Extensible Compact switchgear consisting of One No. Direct Module for Incomer and one No. of Fixed Manual Vacuum Circuit Breaker in SF6 insulated Stainless steel enclosure with series trip,self powered microprocessor based numerical over current and Earth Fault (IDMT+Inst.) relay protection along with. Interconnection between HT switchgear and transformer shall be using 3Cx240 sq.mm Al. armorured XLPE Cable.....1 Set |
| 5 | 1no. 800KVA 11KV/433V Dyn11 Oil filled hermatically sealed transformer without conservator type of design having corrugated tank & Top normal porcelein Bushings for HT & LT with OLTC and RTCC switch of rating +5% to -15% @2.5%. Temp Rise - Oil/Winding 40/50 deg cel, NL/FL Losses = 1.4/14 KW (Subject to IS Tol.), Impedanace 5% (Subject to IS Tol.) .....1 Oil temperature Indicator, Winding Temperature indicator with Alarm and Trip Contact…..1 Set Set LV SIDE 1 Nos. 1600A, 50KA 4 pole microprocessor based EDO, ACB with integral protection Outdoor type enclosure with slanted roof & having construction of Galvanised Sheet Steel of thickness 1.5/2mm. The enclosure shall be type tested for IAC 20 kA/ 1 sec AB class as well as impact test as per IEC 62271-202 or international standards with reports not later than 5 years. The Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP23 degree of protection for Transformer compartment with transformer compartment thermal class of K-20 as per latest IEC. The enclosure shall be Powder Coated (Colour Light Gray & D.A.Gray ). Each compartment will be provided with the door and pad locking arrangement. The Compartment illumination lamp with door operated switch shall be provided for each compartment.....1 Set Interconnection Between HT switchgear & Transformer using 3Cx240Sq.mm XLPE Single core cable & Interconnection between Transformer & LT switchgear using Aluminium Busbars. Internal earthing connections by using 50x6 mm GI strips…...1 Set Supply of 11kV Compact Substation including Receiving,unloading , shifting at designated place, fixing, testing & commissioning as per specifications described above. |
| 6 | 11kV 630Amps 20kA for 3 sec. & tested for 20kA/ 1 sec internal arc , SF6 insulated Non-Extensible Compact switchgear consisting of One No. Direct Module for Incomer and one No. of Fixed Manual Vacuum Circuit Breaker in SF6 insulated Stainless steel enclosure with series trip,self powered microprocessor based numerical over current and Earth Fault (IDMT+Inst.) relay protection along with. Interconnection between HT switchgear and transformer shall be using 3Cx240 sq.mm Al. armorured XLPE Cable.....1 Set ,TRANSFORMER 1no. 500KVA 11KV/433V Dyn11 Oil filled hermatically sealed transformer without conservator type of design having corrugated tank & Top normal porcelein Bushings for HT & LT with OLTC and RTCC switch of rating +5% to -15% @2.5%. Temp Rise - Oil/Winding 40/50 deg cel, NL/FL Losses = 1.4/14 KW (Subject to IS Tol.), Impedanace 5% (Subject to IS Tol.) .....1 Set Oil temperature Indicator, Winding Temperature indicator with Alarm and Trip Contact…..1 Set |
| 7 | 1 Nos. 800A, 50KA 4 pole microprocessor based EDO, ACB with integral protection Outdoor type enclosure with slanted roof & having construction of Galvanised Sheet Steel of thickness 1.5/2mm. The enclosure shall be type tested for IAC 20 kA/ 1 sec AB class as well as impact test as per IEC 62271-202 or international standards with reports not later than 5 years. The Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP23 degree of protection for Transformer compartment with transformer compartment thermal class of K-20 as per latest IEC. The enclosure shall be Powder Coated (Colour Light Gray & D.A.Gray ). Each compartment will be provided with the door and pad locking arrangement. The Compartment illumination lamp with door operated switch shall be provided for each compartment.....1 Set |
| 8 | INTERCONNECTION AND EARTHING Interconnection Between HT switchgear & Transformer using 3Cx240Sq.mm XLPE Single core cable & Interconnection between Transformer & LT switchgear using Aluminium Busbars. Internal earthing connections by using 50x6 mm GI strips…...1 Set Supply of 11kV Compact Substation including Receiving,unloading , shifting at designated place, fixing, testing & commissioning as per specifications described above. |
| 9 | Supply and fixing in position the approved \\"shock treatment charts\\" framed in teak wood frame and covered with glass in front as required in two languages (Hindi & English) |
| 10 | Supply & fixing of Mimic diagram for overall schematic of power distribution complete as required. |
| 11 | Supply and fixing in position the best quality \\"Danger Boards\\" of approved shape and size as specified by Local Electricity Authorities written in English and Local languages. . 11 KV (250mm X 200mm) |
| 12 | Supply and fixing in position the best quality \\"Danger Boards\\" of approved shape and size as specified by Local Electricity Authorities written in English and Local languages. 440V (150mm X 100mm) |
| 13 | Supply & Laying of non skid Electro mat 1 mtr wide and 3.0 mm thick 11 KV grade conforming to IS 15652 as required including cutting to required length complete as per requirement of local electricity authorities. |
| 14 | Supply of fire buckets 5 nos. 15 litre capacity duly filled with fine sand and fixed on an angle iron frame as per requirement of local authorities. The fire buckets shall be painted red from outside and white from inside, including lettered as FIRE with white colour with extra handle at bottom. |
| 15 | Supply & Laying of non skid Electro mat 1mtr wide and 2.0 mm thick 11 KV grade IS 15652 as required including cutting to required length complete as per requirement of local electricity authorities. |
| 16 | Supply & Laying of Rubber hand gloves 33 KV grade, as per IS 4770-1968. |
| 17 | Supply of standard first aid box as approved by Indian red cross society/ St.John Ambulance Brigade and conforming to IS 2217-1963. |
| 18 | Supply & Installation of Earthing Trucks (Casette type) of same Make as HT Panel complete as required. |
| 19 | S.I.T.C of following 1100V grade PVC insulated armoured copper conductor control cables on existing cable tray/ trench as per specifications including of all clamps/ saddles/screw and cable identification tags etc. complete as required including termination of the following sizes of PVC insulated Copper conductor cable including providing terminal lugs,single compression gland , crimping the joints ,providing insulation tape,effecting terminal connections to the equipment.(For HT Panel controls, Transformer Protection, PLC controls. 2C X 2.5sq.mm Cu. Cable |
| 20 | S.I.T.C of following 1100V grade PVC insulated armoured copper conductor control cables on existing cable tray/ trench as per specifications including of all clamps/ saddles/screw and cable identification tags etc. complete as required including termination of the following sizes of PVC insulated Copper conductor cable including providing terminal lugs,single compression gland , crimping the joints ,providing insulation tape,effecting terminal connections to the equipment.(For HT Panel controls, Transformer Protection, PLC controls. 10C X 2.5sq.mm Cu. Cable |
| 21 | S.I.T.C of following 1100V grade PVC insulated armoured copper conductor control cables on existing cable tray/ trench as per specifications including of all clamps/ saddles/screw and cable identification tags etc. complete as required including termination of the following sizes of PVC insulated Copper conductor cable including providing terminal lugs,single compression gland , crimping the joints ,providing insulation tape,effecting terminal connections to the equipment.(For HT Panel controls, Transformer Protection, PLC controls.2C X 1.5sq.mm Cu. Cable |
| 22 | S.I.T.C of following 1100V grade PVC insulated armoured copper conductor control cables on existing cable tray/ trench as per specifications including of all clamps/ saddles/screw and cable identification tags etc. complete as required including termination of the following sizes of PVC insulated Copper conductor cable including providing terminal lugs,single compression gland , crimping the joints ,providing insulation tape,effecting terminal connections to the equipment.(For HT Panel controls, Transformer Protection, PLC controls.12C X 1.5sq.mm Cu. Cable |
| 23 | Supplying, Receiving, shifting, and commissioning of following sizes of 11 KV grade XLPE insulated aluminium conductor armoured power cables conforming to IS : 7098 (Part-II) laid buried in ground / trench / existing Hume pipe / PVC pipe / GI pipe in an approved manner complete as required and as per specifications including excavation of trench in all classes of soil, including supply and provision of sand bed above the cable and below the cable with supply and laying of 1st class brick protection back filling of the trench with excavated earth free from boulders after laying and dressing of the cable in an approved manner complete as required as per IS1255 and as per drawing. 3 core X 300 sq. mm |
| 24 | Laying of one number XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm |
| 25 | Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm |
| 26 | Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm |
| 27 | APPROVAL / LIASIONING WORK WITH STATUTORY AUTHORITIES : (i) Charges for Liasioning with State Electricity Board for getting approvals, clearances for load sanction and obtaining connection etc. Complete for energising the installation with State Electricity Board power as required. The charges shall broadly include but not limited to following and as per SCC. (ii) Load application, load sanction, drawing / scheme approval by CEIG / any other statutory bodies, inspection and approval of installation by CEIG / any other statutory bodies, demand notice & estimate, service connection order, permanent connection and energization. |
| 28 | LT PANELS & DISTRIBUTION PANELS, fulsungi site The contractor shall consider the following details in their item rates, wherever required: Supporting rigid steel framework. Cubicle type, 14 gauge CRCA sheet steel enclouser. Complete with interconnections and distribution bus bars. Proper bonding to earth. Painting/lettering on Breakers and distribution boards, the location they serve, providing on each panel its circuit diagram. Providing cable clamps / supports within distribution boards cable alley. TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link. All MCB 10KA C Curve’s shall be of minimum 10 KA breaking capacity. All motor feeders MCCBs shall be of motor duty. Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5 Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993.. IP 42 for indoor panels. IP 54 for kitchen and laundry panels. IP 55 for outdoor panels All MCCB’s shall be provided with operating mechanism for door interlock. Current density of aluminium shall be 1 sq mm for 1.0 amps for rated current of bus bars and current density of copper shall be 1 sq.mm for 1.25 amps for rated current of bus bars.Tinned copper earth bus shall be provided through out the length of each board. All measuring instruments (Meters) shall be of digital electronic with LED of approved make and compatible with BAS. All hinged door shall be earthed through 4.0 sq mm tinned braided copper wire. All panels shall have provision of the following: Pad locking of Switch board doors. Pad locking of MCCB’s handles in “OFF” Position. Additional set of C.T.s, potential free contacts, connectors, contactors with wiring etc are to be provided for BAS including space required for various transducers in Main Switch Board sections. Only transducers shall be supplied by BAS contractor. |
| 29 | All MCB 10KA C Curve’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type D characteristic. All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single tier formation. All PTs / control transformer shall be provided with centre tap earth secondary. All DOL & Star-Delta Starters shall be provided with SPPR (single phase preventor relay) and 2 nos. of Aux.Contacts for Remote operation/monitor.The Panel fabricator shall provide Al./ Copper Bus-bars link from Breakers wherever more than two nos. of cables are terminated in the breakers. Readymade 16 SWG Sheet steel Enclosure with cutout For MCB 10KA C Curves The equipment shall be designed to conform to the requirements of Low Voltage switchgear Assemblies IEC61439-1& 2 The switchboard along with ACBs and connections should have been type tested design as per IEC 61439 1 & 2 for short circuit, temperature rise, protective earth short circuit test and dielectric tests of the ratings required, As specified in the BOQ the switchboard shall be form 4B, For form of separation only metallic covers shall be used , Hylem / PVC sheets shall not be allowed Frame of Switchboard shall be made of GI 275GSM Zinc coated metal with mimumum of 9 fold design structure. No welding frame to be considered All bus bar support shall be of material Glass Reinforced polyamide, this is required to have better strength & insulation properties Switchboard shall have finger touch proof design with rear Terminals for MCCB feeders. Rear stud terminals shall be used directly on MCCB to avoid any direct touch in the front. Metal based Polyurethane gaskets between all adjacent units and beneath all covers shall be provided to render the joints dust and vermin proof to provide required degree of protection as stipulated in schedule of quantities . The unused openings within the switchboards shall be closed using suitable grommets Panel shall be tested for Internal arc as per IEC61641 – 50Ka for 0.3 sec Panel shall be tested for Seismic withstand of Zone-IV |
| 30 | Busbars shall be made of high conductivity, 99.9% purity, high strength Aluminium of ETP grade Busbars shall be of rectangular cross sections , suitable for full load current for phase bus bars and half/ full rated current for neutral bus bar or as stipulated in schedule of quantities. Busbar shall be suitable to withstand the stresses of fault level as specified in schedule of quantities. All incomer ACBs of Main LT Panel, Capacitor Panels & DG Panels shall be with microprocessor based releases (O/C, S/C & E/F), display of current/voltage and inbuilt onboard Ethernet Modbus TCP/IP communication port (Ics=100%Icu=Icw for 1 Sec ) All ACB release shall be suitable for communication between breakers to enable zone selective interlocking. This feature shall be provided for both short circuit and ground fault protection zones to offer total discrimination between breakers. This feature enables the clearance of fault conditions, thereby reducing the thermal and dynamic stresses produced during fault conditions and thus minimizes the damage to the system. To implement ZSI manufacturer should supply all related equipment like power supply, wiring etc. All ACB protection release shall be suitable for communication on TCP/IP Ethernet The release should have the following measurement functions such as Current, Voltage, Power, Power factor, frequency and peak factor, Phase Sequence, Energy, includes current and voltage both The release shall have wide touch screen LCD display with possibility to view the maximum parameters and bar graph display for % loading of phases. It shall also have bar graph to indicate individual phase loading and identify whether all phases are evenly loaded The protection release shall be able to provide information about the last 20 trips with interrupted fault value and last 200 events (for eg. Open/close of breaker, alarm, editing setting, time stamp etc). The release should have the following measurement functions such as Current (class 1), Voltage (Class 0.5), Power (Class 2) The protection release shall be able to provide information Number of operations (mechanical and electrical), Contact Wear, Load profile and the last maintenance carried out – Locally as well as on communication network connected with EMS/BMS/EDCS/SCADA. |
| 31 | Total Discrimination – There shall be total discrimination between upstream circuit breaker to downstream circuit breaker for the complete project. Panel manufacturer /Switchgear manufacturer shall submit the complete study report generated through software’s reports. Manufacturer shall also submit published discrimination tables during drawing approvals. The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermal magnetic releases upto 250 amps and miroprocessor based above 250 amps capacity, unless specified otherwise. All the ACBs must be equipped with features like ZSI, Thermal Memory, last 20 trip histories, current & Voltage Metering, % loading Bar graph, LED fault Indication, contact wear, display of per phase energy & Total Harmonics Distortion All the MCCBs in Main Panel to communicate ON/OFF/TRIP status on Ethernet. ( MODBUS TCP/IP) ACB shall comply with standards IS/IEC 60947-1 & 2 ACB shall have a rated operational voltage of 415V AC, rated insulation voltage of 1000 volts AC, rated impulse voltage of 12kV. ACB shall have a Ready to close mechanism preferably having a ready to close mechanical indication on front of ACB. All EDO ACBs ready to close indication contact MCCB shall have a rated operational voltage (Ue) of 415V, insulation voltage (Ui) of 800V (AC 50/60 Hz) & impulse voltage (Uimp) of not less than 8kV. Panel Makes -ABB (ARTUK)/Schneider (Blokset)/Siemens (Sivacon) OEM or their authoised Channel partner for TTA panels. ACB, MCCB, TVSS, Meter, ATS makes & Panels Accessories - ABB/Schneider/Siemens MCCBs shall be current limiting type having a double break design (above 250A) Protection Releases Microprocessor based (PRMB) & (upto 250A) Thermal magnetic (PRTM) shall be as described below . |
| 32 | Protection Release Microprocessor Based (PRMB-1) For ACB, Over-current/long time protection range 40% - 100 % with Time setting short circuit /short time protection range 60% - 1000 % with Time setting Instantaneous short circuit Protection range 150% - 1500 % with Time setting Earth Fault Protection range 10% - 100 % with Time setting ZSI(Zone Selectivity Interlocking) Measurements Voltage: phase-phase, phase-neutral currents of the three phases (L1, L2, L3) and of neutral (Ne) with 1% accuracy Energy Power factor ACBs must be equipped with features like ZSI, Thermal Memory, last 20 trip histories and 200 event , current & Voltage Metering, % loading Bar graph, LED fault Indication, contact wear, display of per phase energy & Total Harmonics Distortion with embeded communcaiation MODBUS TCP/IP port for fast communcation. ACBs must be equipped with features like ZSI, Thermal Memory, last 20 trip histories and 200 event , current & Voltage Metering, % loading Bar graph, LED fault Indication, contact wear, display of per phase energy & Total Harmonics Distortion with embeded communcaiation MODBUS TCP/IP port for fast communcation. Protection Release Microprocessor Based (PRMB-3) For MCCB Overload protection setting 40% to 100% short circuit protection Protection Release Thermal-Magnetic Based (PRTM) For MCCB Over-current protection setting 70% to 100% Short circuit |
| 33 | Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 4B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 50 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks and including GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. (Note:The contractor may select the next higher fault rating of MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maximum fault level of the panel). Note:- Panel above 250Amp shall be TTA Type |
| 34 | SITC of Main LT Panel, IP:42 Bus Section-01, From 800 KVA Compact Substation, 1 No. 1250A 4 pole microprocessor based EDO, ACB (35kA) with integral protection as per PRMB-1 mentioned in Premable 1 set of 800/5A, 15 VA, class-1 CTs for APFC relay1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCB 10KA C Curves. 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB 10KA C Curve 1 No. (0-1250A) Ammeter with ASS with 3 nos. 1250/1A CT's 1Set- of ON/OFF/Trip/ Spring Charged/ Supply On & Trip circuit healthy indicating lamps. 240 V AC Motor wound spring closing mechanism, 1 - 24 volts DC shunt trip coil, 6 nos NO/NC contacts for remote opening & closing, Terminals to receive XLPE insulated Aluminium cables Class – B transient voltage surge suppression devices suitable for 3 phases as per specification. Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port OV Relay/ UV Relay/ Master Trip Relay/ Trip Circuit Supervision Relay/ Circuit Breaker Failure Detection Relay & Negative Phase Sequence Over Current Relay Emergency Push Button, From Solar Panel, 1 Nos. 100A 4 pole microprocessor based MCCB (35kA) with integral protection as per PRMB 1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCB 10KA C Curves. 1Set- of ON/OFF/Trip indicating lamps.6 nos NO/NC contacts for remote opening & closing, Terminals to receive XLPE insulated Aluminium cables, Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port |
| 35 | From 380 KVA DG Set-01:-1 Nos. 630A 4 pole microprocessor based MCCBB (35kA) with integral protection as per PRMB mentioned in Premable 1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCB 10KA C Curves. 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB 10KA C Curve 1 No. (0-630A) Ammeter with ASS with 3 nos.630/1A CT's 1Set- of ON/OFF/Trip/ Spring Charged/ Supply On & Trip circuit healthy indicating lamps. 240 V AC Motor wound spring closing mechanism 1 - 24 volts DC shunt trip coil, 6 nos NO/NC contacts for remote opening & closing, Terminals to receive XLPE insulated Aluminium cables Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port Class – B transient voltage surge suppression devices suitable for 3 phases as per specification. Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port OV Relay/ UV Relay/ Master Trip Relay/ Trip Circuit Supervision Relay/ Circuit Breaker Failure Detection Relay & Negative Phase Sequence Over Current Relay Emergency Push Button Busbar Electrolytic high conductivity Aluminium three phase and neutral busbars with earthing rated at 1000 amps having a maximum current density of 0.8 amp per sq mm suitable to with stand symmetrical fault level of 50 kA at 433 volts. The neutral busbar is to be of 50% capacity. |
| 36 | Outgoings:Bus Section-1, 2 No. 800A FP,EDO ACB(35 KA) complete with:3 nos 800/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 3 No. 630A FP MCCB(35 KA) complete with: 3 nos 630/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 1 No. 250A FP MCCB(35 KA) complete with: 3 nos 250/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 2 No. 160A FP MCCB(35 KA) complete with: 3 nos 160/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 1 No. 125A FP MCCB(35 KA) complete with: 3 nos 125/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 2 No. 100A FP MCCB(35 KA) complete with: 3 nos 100/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified.1 No. 63A FP MCCB(35 KA) complete with: 3 nos 63/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. Buscoupler 1 No. 1600Amps, 50KA, 433 volt 4-P EDO ACB without release complete with following: 6 Nos. NO/NC contacts for remote opening & closing Red/Green / Amber / ON/OFF / Trip indicating lamps with 2A SP MCB 10KA C Curve as backup protection. Backup MCB 10KA C Curve and terminal blocks as required. TNC Breaker Control switch Required Interlocking with other incomers & Bus Coupler to be provided as per Interlocking / operation scheme. |
| 37 | Bus Section-02, From 380 KVA DG Set , 1 Nos. 630A 4 pole microprocessor based MCCBB (35kA) with integral protection as per PRMB mentioned in Premable1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCB 10KA C Curves. 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB 10KA C Curve 1 No. (0-630A) Ammeter with ASS with 3 nos.630/1A CT's 1Set- of ON/OFF/Trip/ Spring Charged/ Supply On & Trip circuit healthy indicating lamps. 240 V AC Motor wound spring closing mechanism 1 - 24 volts DC shunt trip coil 6 nos NO/NC contacts for remote opening & closing Terminals to receive XLPE insulated Aluminium cables Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port Class – B transient voltage surge suppression devices suitable for 3 phases as per specification. Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 portOV Relay/ UV Relay/ Master Trip Relay/ Trip Circuit Supervision Relay/ Circuit Breaker Failure Detection Relay & Negative Phase Sequence Over Current Relay, Emergency Push Button, Busbar Electrolytic high conductivity Aluminium three phase and neutral busbars with earthing rated at 1600 amps having a maximum current density of 0.8 amp per sq mm suitable to with stand symmetrical fault level of 50 kA at 433 volts. The neutral busbar is to be of 50% capacity. |
| 38 | Outgoings:Bus Section-2, 1 No. 630A FP MCCB(35 KA) complete with: 3 nos 630/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 2 No. 250A FP MCCB(35 KA) complete with: 3 nos 250/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 1 No. 160A FP MCCB(35 KA) complete with: 3 nos 160/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 4 No. 100A FP MCCB(35 KA) complete with: 3 nos 100/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 3 No. 63A FP MCCB(35 KA) complete with: 3 nos 63/1A Class - 1.0, 15 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified.LT Panel Descrived Above |
| 39 | LT PANELS & DISTRIBUTION PANELS transit camp site, The contractor shall consider the following details in their item rates, wherever required: Supporting rigid steel framework. Cubicle type, 14 gauge CRCA sheet steel enclouser. Complete with interconnections and distribution bus bars. Proper bonding to earth. Painting/lettering on Breakers and distribution boards, the location they serve, providing on each panel its circuit diagram. Providing cable clamps / supports within distribution boards cable alley. TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link. All MCB 10KA C Curve’s shall be of minimum 10 KA breaking capacity. All motor feeders MCCBs shall be of motor duty. Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5 Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993.. IP 42 for indoor panels. IP 54 for kitchen and laundry panels. IP 55 for outdoor panels All MCCB’s shall be provided with operating mechanism for door interlock. Current density of aluminium shall be 1 sq mm for 1.0 amps for rated current of bus bars and current density of copper shall be 1 sq.mm for 1.25 amps for rated current of bus bars.Tinned copper earth bus shall be provided through out the length of each board. All measuring instruments (Meters) shall be of digital electronic with LED of approved make and compatible with BAS. All hinged door shall be earthed through 4.0 sq mm tinned braided copper wire. All panels shall have provision of the following: Pad locking of Switch board doors. Pad locking of MCCB’s handles in “OFF” Position. Additional set of C.T.s, potential free contacts, connectors, contactors with wiring etc are to be provided for BAS including space required for various transducers in Main Switch Board sections. Only transducers shall be supplied by BAS contractor. |
| 40 | All MCB 10KA C Curve’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type D characteristic. All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single tier formation. All PTs / control transformer shall be provided with centre tap earth secondary. All DOL & Star-Delta Starters shall be provided with SPPR (single phase preventor relay) and 2 nos. of Aux.Contacts for Remote operation/monitor.The Panel fabricator shall provide Al./ Copper Bus-bars link from Breakers wherever more than two nos. of cables are terminated in the breakers. Readymade 16 SWG Sheet steel Enclosure with cutout For MCB 10KA C Curves The equipment shall be designed to conform to the requirements of Low Voltage switchgear Assemblies IEC61439-1& 2 The switchboard along with ACBs and connections should have been type tested design as per IEC 61439 1 & 2 for short circuit, temperature rise, protective earth short circuit test and dielectric tests of the ratings required, As specified in the BOQ the switchboard shall be form 4B, For form of separation only metallic covers shall be used , Hylem / PVC sheets shall not be allowed Frame of Switchboard shall be made of GI 275GSM Zinc coated metal with mimumum of 9 fold design structure. No welding frame to be considered All bus bar support shall be of material Glass Reinforced polyamide, this is required to have better strength & insulation properties Switchboard shall have finger touch proof design with rear Terminals for MCCB feeders. Rear stud terminals shall be used directly on MCCB to avoid any direct touch in the front. Metal based Polyurethane gaskets between all adjacent units and beneath all covers shall be provided to render the joints dust and vermin proof to provide required degree of protection as stipulated in schedule of quantities . The unused openings within the switchboards shall be closed using suitable grommets Panel shall be tested for Internal arc as per IEC61641 – 50Ka for 0.3 sec Panel shall be tested for Seismic withstand of Zone-IV |
| 41 | Busbars shall be made of high conductivity, 99.9% purity, high strength Aluminium of ETP grade Busbars shall be of rectangular cross sections , suitable for full load current for phase bus bars and half/ full rated current for neutral bus bar or as stipulated in schedule of quantities. Busbar shall be suitable to withstand the stresses of fault level as specified in schedule of quantities. All incomer ACBs of Main LT Panel, Capacitor Panels & DG Panels shall be with microprocessor based releases (O/C, S/C & E/F), display of current/voltage and inbuilt onboard Ethernet Modbus TCP/IP communication port (Ics=100%Icu=Icw for 1 Sec ) All ACB release shall be suitable for communication between breakers to enable zone selective interlocking. This feature shall be provided for both short circuit and ground fault protection zones to offer total discrimination between breakers. This feature enables the clearance of fault conditions, thereby reducing the thermal and dynamic stresses produced during fault conditions and thus minimizes the damage to the system. To implement ZSI manufacturer should supply all related equipment like power supply, wiring etc. All ACB protection release shall be suitable for communication on TCP/IP Ethernet The release should have the following measurement functions such as Current, Voltage, Power, Power factor, frequency and peak factor, Phase Sequence, Energy, includes current and voltage both The release shall have wide touch screen LCD display with possibility to view the maximum parameters and bar graph display for % loading of phases. It shall also have bar graph to indicate individual phase loading and identify whether all phases are evenly loaded The protection release shall be able to provide information about the last 20 trips with interrupted fault value and last 200 events (for eg. Open/close of breaker, alarm, editing setting, time stamp etc). The release should have the following measurement functions such as Current (class 1), Voltage (Class 0.5), Power (Class 2) The protection release shall be able to provide information Number of operations (mechanical and electrical), Contact Wear, Load profile and the last maintenance carried out – Locally as well as on communication network connected with EMS/BMS/EDCS/SCADA. |
| 42 | Total Discrimination – There shall be total discrimination between upstream circuit breaker to downstream circuit breaker for the complete project. Panel manufacturer /Switchgear manufacturer shall submit the complete study report generated through software’s reports. Manufacturer shall also submit published discrimination tables during drawing approvals. The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermal magnetic releases upto 250 amps and miroprocessor based above 250 amps capacity, unless specified otherwise. All the ACBs must be equipped with features like ZSI, Thermal Memory, last 20 trip histories, current & Voltage Metering, % loading Bar graph, LED fault Indication, contact wear, display of per phase energy & Total Harmonics Distortion All the MCCBs in Main Panel to communicate ON/OFF/TRIP status on Ethernet. ( MODBUS TCP/IP) ACB shall comply with standards IS/IEC 60947-1 & 2 ACB shall have a rated operational voltage of 415V AC, rated insulation voltage of 1000 volts AC, rated impulse voltage of 12kV. ACB shall have a Ready to close mechanism preferably having a ready to close mechanical indication on front of ACB. All EDO ACBs ready to close indication contact MCCB shall have a rated operational voltage (Ue) of 415V, insulation voltage (Ui) of 800V (AC 50/60 Hz) & impulse voltage (Uimp) of not less than 8kV. Panel Makes -ABB (ARTUK)/Schneider (Blokset)/Siemens (Sivacon) OEM or their authoised Channel partner for TTA panels. ACB, MCCB, TVSS, Meter, ATS makes & Panels Accessories - ABB/Schneider/Siemens MCCBs shall be current limiting type having a double break design (above 250A) Protection Releases Microprocessor based (PRMB) & (upto 250A) Thermal magnetic (PRTM) shall be as described below . |
| 43 | Protection Release Microprocessor Based (PRMB-1) For ACB, Over-current/long time protection range 40% - 100 % with Time setting short circuit /short time protection range 60% - 1000 % with Time setting Instantaneous short circuit Protection range 150% - 1500 % with Time setting Earth Fault Protection range 10% - 100 % with Time setting ZSI(Zone Selectivity Interlocking) Measurements Voltage: phase-phase, phase-neutral currents of the three phases (L1, L2, L3) and of neutral (Ne) with 1% accuracy Energy Power factor ACBs must be equipped with features like ZSI, Thermal Memory, last 20 trip histories and 200 event , current & Voltage Metering, % loading Bar graph, LED fault Indication, contact wear, display of per phase energy & Total Harmonics Distortion with embeded communcaiation MODBUS TCP/IP port for fast communcation. ACBs must be equipped with features like ZSI, Thermal Memory, last 20 trip histories and 200 event , current & Voltage Metering, % loading Bar graph, LED fault Indication, contact wear, display of per phase energy & Total Harmonics Distortion with embeded communcaiation MODBUS TCP/IP port for fast communcation. Protection Release Microprocessor Based (PRMB-3) For MCCB Overload protection setting 40% to 100% short circuit protection Protection Release Thermal-Magnetic Based (PRTM) For MCCB Over-current protection setting 70% to 100% Short circuit |
| 44 | Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 4B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 50 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks and including GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below.(Note:The contractor may select the next higher fault rating of MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maximum fault level of the panel). Note:- Panel above 250Amp shall be TTA Type |
| 45 | SITC of Main LT Panel IP:42 Bus Section-01 From 500 KVA Compact Substation 1 No. 800A 4 pole microprocessor based EDO, ACB (35kA) with integral protection as per PRMB-1 mentioned in Premable 1 set of 800/5A, 15 VA, class-1 CTs for APFC relay 1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCB 10KA C Curves. 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB 10KA C Curve 1 No. (0-800A) Ammeter with ASS with 3 nos. 800/1A CT's 1Set- of ON/OFF/Trip/ Spring Charged/ Supply On & Trip circuit healthy indicating lamps. 240 V AC Motor wound spring closing mechanism 1 - 24 volts DC shunt trip coil 6 nos NO/NC contacts for remote opening & closing Terminals to receive XLPE insulated Aluminium cables Class – B transient voltage surge suppression devices suitable for 3 phases as per specification. Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port OV Relay/ UV Relay/ Master Trip Relay/ Trip Circuit Supervision Relay/ Circuit Breaker Failure Detection Relay & Negative Phase Sequence Over Current Relay Emergency Push Button |
| 46 | From Solar Panel 1 Nos. 100A 4 pole microprocessor based MCCB (35kA) with integral protection as per PRMB 1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCB 10KA C Curves. 1Set- of ON/OFF/Trip indicating lamps. 6 nos NO/NC contacts for remote opening & closing Terminals to receive XLPE insulated Aluminium cables Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port Busbar Electrolytic high conductivity Aluminium three phase and neutral busbars with earthing rated at 1000 amps having a maximum current density of 0.8 amp per sq mm suitable to with stand symmetrical fault level of 50 kA at 433 volts. The neutral busbar is to be of 50% capacity. |
| 47 | Outgoings:Bus Section-1 3 No. 500A FP MCCB(35 KA) complete with: 3 nos 500/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 3 No. 160A FP MCCB(35 KA) complete with: 3 nos 160/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 1 No. 125A FP MCCB(35 KA) complete with: 3 nos 125/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. |
| 48 | 1 No. 100A FP MCCB(35 KA) complete with: 3 nos 100/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 2 No. 63A FP MCCB(35 KA) complete with: 3 nos 63/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection.Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified.Buscoupler1 No. 1000Amps, 50KA, 433 volt 4-P EDO ACB without release complete with following: 6 Nos. NO/NC contacts for remote opening & closing Red/Green / Amber / ON/OFF / Trip indicating lamps with 2A SP MCB 10KA C Curve as backup protection. Backup MCB 10KA C Curve and terminal blocks as required. TNC Breaker Control switch Required Interlocking with other incomers & Bus Coupler to be provided as per Interlocking / operation scheme. Bus Section-02 From 380 KVA DG Set Buscoupler1 No. 1000Amps, 50KA, 433 volt 4-P EDO ACB without release complete with following: 6 Nos. NO/NC contacts for remote opening & closing Red/Green / Amber / ON/OFF / Trip indicating lamps with 2A SP MCB 10KA C Curve as backup protection. Backup MCB 10KA C Curve and terminal blocks as required. TNC Breaker Control switch Required Interlocking with other incomers & Bus Coupler to be provided as per Interlocking / operation scheme. |
| 49 | 1 Nos. 630A 4 pole microprocessor based MCCBB (35kA) with integral protection as per PRMB mentioned in Premable 1 set of R,Y,B phase indicating lamps each with 3 nos. 2A SP MCB 10KA C Curves. 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB 10KA C Curve 1 No. (0-630A) Ammeter with ASS with 3 nos.630/1A CT's 1Set- of ON/OFF/Trip/ Spring Charged/ Supply On & Trip circuit healthy indicating lamps. 240 V AC Motor wound spring closing mechanism 1 - 24 volts DC shunt trip coil 6 nos NO/NC contacts for remote opening & closing Terminals to receive XLPE insulated Aluminium cables Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port Class – B transient voltage surge suppression devices suitable for 3 phases as per specification. Multifunction meter with display of V,I,PF,Energy,Power, Harmonics up to 15th order & %THD with RS485 port OV Relay/ UV Relay/ Master Trip Relay/ Trip Circuit Supervision Relay/ Circuit Breaker Failure Detection Relay & Negative Phase Sequence Over Current Relay Emergency Push Button |
| 50 | Busbar Electrolytic high conductivity Aluminium three phase and neutral busbars with earthing rated at 1000 amps having a maximum current density of 0.8 amp per sq mm suitable to with stand symmetrical fault level of 50 kA at 433 volts. The neutral busbar is to be of 50% capacity.Outgoings:Bus Section-2 1 No. 200A FP MCCB(35 KA) complete with: 3 nos 200/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified.2 No. 160A FP MCCB(35 KA) complete with: 3 nos 160/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. |
| 51 | 2 No. 100A FP MCCB(35 KA) complete with: 3 nos 100/1A Class - 1.0, 5 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection. Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. 4 No. 63A FP MCCB(35 KA) complete with: 3 nos 63/1A Class - 1.0, 15 VA Burden CT's for metering ON / OFF & Auto Trip indicating lamps with MCB 10KA C Curve as backup protection.Digital Three Phase, four wire, multifunction Meter with V, A, KWH, 485 Communication Port, Class of Accuracy-1 as specified. LT Panel Descrived Above |
| 52 | SITC of Lift Panel Incomer 1 No. 63amps 4P MCCB(35KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. 1 No.63 amp 4 Pole ATS (automatic transfer switch) solenoid operated, Automatic operation & complete Neutral overlapping, equipped with built in controller, the controller and ATS should be one unit with LCD display, controller should be onsite replaceable at the time of event of fault. Metering & Indication for each Incomer 1 set of R,Y,B phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port.Sets of 63/1A, CL-1, 15VA CTs for measuring. Sets of On/Off indicating lamp with 2A control MCB 10KA C Curves. Emergency Push Button with Each Incomer Busbar 100 A TP+100%Neutral Aluminium Bus Bar with colour coded PVC SleevesOutgoings 3 Nos.25 Amp TP MPCB 10KA with short circuit, overload and phase loss protection 3 Nos.32 Amp FP MCB 10KA with short circuit 2 Nos.40 Amp DP MCB 10KA with short circuit Lift Panel as described above |
| 53 | SITC of Lift Panel Incomer 1 No. 100amps 4P MCCB(35KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. 1 No.100 amp 4 Pole ATS (automatic transfer switch) solenoid operated, Automatic operation & complete Neutral overlapping, equipped with built in controller, the controller and ATS should be one unit with LCD display, controller should be onsite replaceable at the time of event of fault.Metering & Indication for each Incomer 1 set of R,Y,B phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port. Sets of 100/1A, CL-1, 15VA CTs for measuring. Sets of On/Off indicating lamp with 2A control MCB 10KA C Curves. Emergency Push Button with Each Incomer Busbar 125 A TP+100%Neutral Aluminium Bus Bar with colour coded PVC Sleeves Outgoings 5 Nos.25 Amp TP MPCB 10KA with short circuit, overload and phase loss protection 5 Nos.32 Amp FP MCB 10KA with short circuit 5 Nos.40 Amp DP MCB 10KA with short circuit Lift Panel as described above |
| 54 | SITC of Capacitor Panel Incomer (270kVAR)1 No. 800A ACB FP ACB 35KA with Microprcoesaor based integral protection as per PRMB-1 mentioned in Premable 1 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective SP MCB 10KA C Curve (96mm square) (one for each Incoming Breaker). 1 No. 0 to 800Amp digital ammeter (96mm square) with CT's. 1 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker). 1Set- of ON/OFF/Trip/ Spring Charged/ Supply On & Trip circuit healthy indicating lamps. 9 Step Automatic Power Factor Correction relay (APFC relay). Busbar 630 Amp TP+NEUTRAL busbars of aluminium alloy as per SLD. Outgoings 1 Nos.250 Amp TP MCCB. 1 Nos. capacitor duty contactor (one for each 100 KVAR capacitor unit with APP type Capacitor bank) 2 Nos.125 Amp TP MCCB. 2 Nos. capacitor duty contactor (one for each 50 KVAR capacitor unit with APP type Capacitor bank) , 2 Nos. 63 Amp TP MCCB., 2 Nos. capacitor duty contactor (one for each 20 KVAR capacitor unit with APP type Capacitor bank) , 2 Nos. 32 Amp TP MCCB. , 2 Nos. capacitor duty contactor (one for each 10 KVAR capacitor unit with APP type Capacitor bank), 2 Nos. 32 Amp TP MCCB., 2 Nos. capacitor duty contactor (one for each 5 KVAR capacitor unit with APP type Capacitor bank) , 9 sets of push button stations with indicator Red and Green for manual operation of capacitor units with auto/manual selector switches. 1 No. Indicating lamp for each 50/ 20/ 10/ 5KVAR capacitor unit to indicate that the unit is 'ON'.1 No. Toggle switch for changing automatic to manual operation of capacitor units. Power factor meter. Capacitor Panel Described as above |
| 55 | SITC of Plumbing Panel Incomer:- 1 No. 100amps 4P MCCB(35KA) with overcurrent,earth fault and short circuit releases each complete with 1 No.100 amp 4 Pole ATS (automatic transfer switch) solenoid operated, Automatic operation & complete Neutral overlapping, equipped with built in controller, the controller and ATS should be one unit with LCD display, controller should be onsite replaceable at the time of event of fault. Metering & Indication for each Incomer 1 set of R,Y,B phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port. Sets of 100/1A, CL-1, 15VA CTs for measuring. Sets of On/Off indicating lamp with 2A control MCB 10KA C Curves. Emergency Push Button with Each Incomer Busbar 125A TP+100%Neutral Aluminium Bus Bar with colour coded PVC Sleeves Outgoings7 No. 40amps FP MCB 10KA C Curve with Suitable Startor 4 No. 25amps FP MCB 10KA C Curve with Suitable Startor 2 No. 125amps FP MCCB 25KA C Curve with Suitable Startor The contractor would be considerd startor rating as per final SLD without any extra cost. Plumbing Panel Descrived Avobe |
| 56 | SITC of Fire-Fighting Panel Incomer:- 1 No. 250amps 4P MCCB(36KA) with overcurrent,earth fault and short circuit releases each complete with 1 No.250 amp 4 Pole ATS (automatic transfer switch) solenoid operated, Automatic operation & complete Neutral overlapping, equipped with built in controller, the controller and ATS should be one unit with LCD display, controller should be onsite replaceable at the time of event of fault.Metering & Indication for each Incomer 1 set of R,Y,B phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port. Sets of 250/1A, CL-1, 15VA CTs for measuring. Sets of On/Off indicating lamp with 2A control MCB 10KA C Curves. Emergency Push Button with Each Incomer Busbar 400A TP+100%Neutral Aluminium Bus Bar with colour coded PVC Sleeves Outgoings 3 No. 100amps FP MCCB 25KA C Curve with suitable startor 3 No. 63amps FP MCB 10KA C Curve with suitable startor 2 No. 40amps FP MCB 10KA C Curve with suitable startor The contractor would be considerd startor rating as per final SLD without any extra cost. Fire Fighting Panel Descrived Above |
| 57 | Designing, SITC of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification (INCOMER & METERING) 400A, 50kA 4 Pole MCCB, Ics=100% Icu Rating Digital Voltmeter 0-500V with selector switch Ammeter (0-400 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Bus Bar 500Amps (OUTGOING) (a) MAIN FIRE PUMP- 03 Nos of 125 Amp, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 hp pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. - 2 sets (b) JOCKEY PUMP 03 Nos of 63 Amp, 50kA TPN MCCB, Ics=100% Icu, with Suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.(c) 2 No. of 40amps FP MCB 10KA C Curve with suitable startor (d)DIESEL ENGINE CONTROL Control for diesel engine comprising - Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0- 20 A DC Ammeter The contractor would be considerd startor rating as per final SLD without any extra cost. Fire Fighting Panel Descrived Above |
| 58 | SITC of Drainage Sump Panel, Incomer:-1 No. 63amps 4P MCCB(36KA) with overcurrent,earth fault and short circuit releases each complete with Metering & Indication for each Incomer 1 set of R,Y,B phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port. Sets of 63/1A, CL-1, 15VA CTs for measuring. Sets of On/Off indicating lamp with 2A control MCB 10KA C Curves. Busbar 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves Outgoings 6 No. 32amps FP MCB 10KA C CurveDrainage Sump Panel Described Above |
| 59 | SITC of Ventilation & Pressurization Panel:- Incomer:- 1 No. 160amps 4P MCCB(36KA) with overcurrent,earth fault and short circuit releases each complete with 1 No.160 amp 4 Pole ATS (automatic transfer switch) solenoid operated, Automatic operation & complete Neutral overlapping, equipped with built in controller, the controller and ATS should be one unit with LCD display, controller should be onsite replaceable at the time of event of fault. Metering & Indication for each Incomer 1 set of R,Y,B phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port.Sets of 160/1A, CL-1, 15VA CTs for measuring.Sets of On/Off indicating lamp with 2A control MCB 10KA C Curves. Emergency Push Button with Each Incomer Busbar 200A TP+100%Neutral Aluminium Bus Bar with colour coded PVC Sleeves Outgoings 16 No. 32amps FP MCB Ventilation & Pressurization Panel As Descrived Above |
| 60 | SITC of Capacitor Panel (170kVAR) Incomer:- 1 No. 500A ACB FP MCCB 35KA with Microprcoesaor based integral protection as per PRMB mentioned in Premable 1 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective SP MCB 10KA C Curve (96mm square) (one for each Incoming Breaker). 1 No. 0 to 500Amp digital ammeter (96mm square) with CT's. 1 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker).1Set- of ON/OFF/Trip/ Spring Charged/ Supply On & Trip circuit healthy indicating lamps. 12 Step Automatic Power Factor Correction relay (APFC relay). Busbar 630 Amp TP+NEUTRAL busbars of aluminium alloy as per SLD. Outgoings 2 Nos.125 Amp TP MCCB. 2 Nos. capacitor duty contactor (one for each 50 KVAR capacitor unit with APP type Capacitor bank) 2 Nos. 63 Amp TP MCCB. 2 Nos. capacitor duty contactor (one for each 20 KVAR capacitor unit with APP type Capacitor bank) 2 Nos. capacitor duty contactor (one for each 10 KVAR capacitor unit with APP type Capacitor bank) 2 Nos. 32 Amp TP MCCB.2 Nos. capacitor duty contactor (one for each 5 KVAR capacitor unit with APP type Capacitor bank) 8 sets of push button stations with indicator Red and Green for manual operation of capacitor units with auto/manual selector switches. 1 No. Indicating lamp for each 50/ 20/ 10/ 5KVAR capacitor unit to indicate that the unit is 'ON'. 1 No. Toggle switch for changing automatic to manual operation of capacitor units.Power factor meter. Capacitor Panel Described as above |
| 61 | SITC of Basement VTPN DB, 1 No. 125amps 4P MCCB (35KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications.200A TPN Copper Bus Bar with colour coded PVC Sleeves Outgoings 4 No. 63amps TP MCB 10KA C Curve 4 No. 40amps TP MCB 10KA C Curve Basement VTPN DB Described as above |
| 62 | SITC of Ground,2nd,3rd,4th,5th,6th,7th & 8th Floor Panel 1 No. 125amps 4P MCCB (35KA) with Thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. Metering & Indication for each Incomer 1 set of R,Y,B phase indicating lamps 1 set of On/Off phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port. Sets of 125/1A, CL-1, 15VA CTs for measuring. Busbar 160A TP+100%Neutral Aluminium Bus Bar with colour coded PVC Sleeves Outgoings, 5 No. 63amps FP MCCB 10KA C Curve 5 No. 40amps FP MCCB 10KA C Curve, 5 No. 40amps DP MCB 10KA C Curve 3 No. 100amps FP MCCB 10KA C CurveGround,2nd,3rd,4th,5th,6th,7th & 8th Floor Panel Described as above |
| 63 | SITC of 1st.Floor Panel 1 No. 160amps 4P MCCB (35KA) with Thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. Metering & Indication 1 set of R,Y,B phase indicating lamps 1 set of On/Off phase indicating lamps Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA, harmonics upto 15th order & %THD) with RS-485 Port. Sets of 160/1A, CL-1, 15VA CTs for measuring. Busbar 200A TP+100%Neutral Aluminium Bus Bar with colour coded PVC Sleeves Outgoings, 4 No. 63amps FP MCCB 10KA C Curve 4 No. 40amps FP MCCB 10KA C Curve 4 No. 40amps DP MCB 10KA C Curve 1st.Floor Panel Described as above |
| 64 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200A tinned copper busbar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and Incomer) as required. 12 way (4+36), Double door |
| 65 | Providing and fixing following rating and breaking capacity and pole MCCB with termomagnetic release and terminal spreaders in existing cubical panel board including drilling holes in cubila panel, making connections, etc.as required 100A, 30KA, FP MCCB |
| 66 | Supplyind and fixing following rating, 415 V, 10KA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A 3P MCB |
| 67 | Supplyind and fixing following rating, 415 V, 10KA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A 3P MCB |
| 68 | SITC of 380KVA DG Set Equipment With AMF Panel Providing, Installing, Testing and Commissioning of 380 KVA ‘Silent Type’ Diesel Generating set along with having Prime Power Rating, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor and consisting of the followings including making necessary civil foundation etc. complete as required: Diesel Engines: Diesel engine 4 stroke water cooled, electric start, of suitable BHP at 1500 RPM suitable for delivering required output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL and conforming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories. Engine mounted Instrument Panel fitted with and having digital display for following: (i) Start-stop switch with key (ii) Water temperature indication (iii) Lubrication oil pressure indication (iv) Battery charging indication (v) RPM indication (vi) Over speed indication (vii) Low lub. Oil trip indication (viii) Engine Hours indication Alternator : Synchronous alternator rated at 380KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated through AVR conforming to IS: 4722/BS 2613 suitable for tropical conditions and with class-F/H insulation. Base Frame & Foundation: Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer. Fuel Tank: Daily service fuel tank of 990 liters capacity respectively fabricated out of 2 mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class ‘C’ pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications. Exhaust System: Dry exhaust manifold with hospital exhaust silencer and catalytic convertor. Starting System: 24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (180 AH capacity lead acid type) as required as per specifications. Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere as per specifications, For in house power Generation for Emergency loads suitable for 380KVA |
| 69 | Supplying and fixing Exhaust gas piping of 1x125 dia. welded black MS, B Class pipe conforming to IS:3589 cut to required lengths and installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with mineral wool/Rockwool, 50 mm thick wire mesh & aluminum cladding etc., as required as per specifications. and exhaust pipe shall be design as per CPWD/CPCB Specifications. |
| 70 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 71 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 72 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 73 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 74 | Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe FRLSom earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 75 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 76 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 77 | Providing and fixing 50 mm X 10 mm copper strip on surface or in recess for connections etc. as required. |
| 78 | Providing and fixing 50 mm X 10 mm G.I. strip on surface or in recess for connections etc. as required. |
| 79 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 80 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 81 | Above 35 sq. mm and upto 95 sq. mm |
| 82 | Above 95 sq. mm and upto 185 sq. mm |
| 83 | Above 185 sq. mm and upto 400 sq. mm |
| 84 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm |
| 85 | Above 35 sq. mm and upto 95 sq. mm |
| 86 | Above 95 sq. mm and upto 185 sq. mm |
| 87 | Above 185 sq. mm and upto 400 sq. mm |
| 88 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Upto 35 sq. mm |
| 89 | Above 35 sq. mm and upto 95 sq. mm |
| 90 | Above 95 sq. mm and upto 185 sq. mm |
| 91 | Above 185 sq. mm and upto 400 sq. mm |
| 92 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 93 | Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 94 | Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 95 | Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) |
| 96 | Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. |
| 97 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm (70mm) |
| 98 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 240 sq. mm (62mm) |
| 99 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm (57mm) |
| 100 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 150 sq. mm (50mm) |
| 101 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 120 sq. mm (45mm) |
| 102 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm) |
| 103 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm) |
| 104 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 50 sq. mm (35mm) |
| 105 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm (32mm) |
| 106 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 4 X 25 sq. mm (28mm) |
| 107 | 4 X 16 sq. Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required mm (28mm) |
| 108 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 4 X 10 sq. mm (25mm) |
| 109 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 4 X 6 Sqmm |
| 110 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3C X 10 sq. mm (22mm) |
| 111 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3 X 6 Sqmm |
| 112 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 2 X 10 sq. mm (19mm) |
| 113 | 2 ½ C - 300 sq mm Aluminium |
| 114 | 3 ½ C - 240 sq mm Aluminium |
| 115 | 3 ½ C - 185 sq mm Aluminium |
| 116 | 3 ½ C - 150 sq mm Aluminium |
| 117 | 3 ½ C - 120 sq mm Aluminium |
| 118 | 3 ½ C - 95 sq mm Aluminium |
| 119 | 3 ½ C - 70 sq mm Aluminium |
| 120 | 3 ½ C - 50 sq mm Aluminium |
| 121 | 3 ½ C - 35 sq mm Aluminium |
| 122 | 4C- 25 sq mm Aluminium |
| 123 | 4C- 16 sq mm Aluminium |
| 124 | 4C- 10 sq mm Aluminium |
| 125 | 4C X 6 Sqmm Aluminium Cable |
| 126 | 3C X 10 Sqmm Aluminium Cable |
| 127 | 3C X 6 Sqmm Aluminium Cable |
| 128 | 2C- 10 sq mm Aluminium |
| 129 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5C x 300 sq mm Aluminium |
| 130 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 240 sq mm Aluminium |
| 131 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 185 sq mm Aluminium |
| 132 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 150 sq mm Aluminium |
| 133 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 120 sq mm Aluminium |
| 134 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 95 sq mm Aluminium |
| 135 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 70 sq mm Aluminium |
| 136 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 50 sq mm Aluminium |
| 137 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 3.5 x 35 sq mm Aluminium |
| 138 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 4C- 25 sq mm Aluminium |
| 139 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 4C- 16 sq mm Aluminium |
| 140 | Supply, following sizes of Fire Survival Aluminium conductor power/ multicore control armoured cable. 4C- 10 sq mm Aluminium |
| 141 | Supply of following sizes XLPE insulated (Heavy duty) Aluminium or Copper conductor armoured cables suitable for working voltage upto and including 1100 Volts complete as required and as per specifications. 2 x 6 sq.mm |
| 142 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 143 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm |
| 144 | Termination of the following sizes of XLPE insulated Aluminium/ Copper conductor cable including providing terminal lugs,double compression gland , crimping the joints ,providing insulation tape,effecting terminal connections to the equipment complete as required. 2 x 6 sq,mm, Al conductor cable |
| 145 | Supply, laying and termination of the following sizes of 650/1100 volts grade PVC insulated copper conductor wires in existing conduits including end terminations with copper lugs. 3 x 2.5 sq.mm. Copper conductor ,PVC insulated PVC sheathed wires |
| 146 | Supplying and fixing in position of the following sizes of GI conduit buried in ground 600 mm deep including all accessories complete as required and as per specifications. 25 mm dia GI conduit |
| 147 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 100mm dia |
| 148 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 250mm dia |
| 149 | Supply,fixing and laying of Heavy duty PVC pipes complete buried in floor with joints and other accessories as required. 63 mm dia, 2mm thick |
| 150 | Supply of Polar pole made of square mild steel pipe (grade YST 210) 100mm Square x 2.9mm thick with 5500mm Height. The split constructed double arm bracket made of MS pipe 100mm square x 2.9mm thick having 900mm arm length and 484mm height inclined at 10 degree. Single arm bracket contains build-in 60W LED module. 60W LED Module with expected service life of at least 60,000 operating hours. High Brightness, LED Light source do not poseany environment risks. Excellent thermal management heat sink. High efficiency polycarbonate optical lens. IP68 Ingress protection. IK09 impact protection.Colour rendering index(Ra) >70. Available colour temperature 3000K / 4000K / 5700K. Driver efficiency > 85%, power factor > 0.95, THD <10%, Surge Protection 6KV. Pole section welded by certified welders using high end MIG welding processes. PDC aluminium service door 330mm height x 75mm width shall be provided with the company logo embossed on the bottom of the door and safety rope with IP protection rating. The control gear tray is prewired with2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way terminal block for loop-in / loop-out arrangement, 5A 2 Way terminal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 300mm Square x 16mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 48 x 24 to suit M20 x 500mm bolts of grade 4.6 at CC 215. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. Afterfabrication entire pole is shot blasted (Inhouse). The pole is coated with epoxy zinc phosphate primer and finished using environmentally stable powder coated (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options. Must have inhouse manufacuturing facilities along with powder coating shot blasting machines.KP-7229+KP-9108. Make: K- Lite/Ligman/Unilamp |
| 151 | Supply of Polar pole made of square mild steel pipe (grade YST 210) 100mm Square x 2.9mm thick with 5500mm Height. The split constructed double arm bracket made of MS pipe 100mm square x 2.9mm thick having 900mm arm length and 484mm height inclined at 10 degree. Double arm bracket contains build-in 2X60W LED module. 60W LED Module with expected service life of at least 60,000 operating hours. High Brightness, LED Light source do not poseany environment risks. Excellent thermal management heat sink. High efficiency polycarbonate optical lens. IP68 Ingress protection. IK09 impact protection.Colour rendering index(Ra) >70. Available colour temperature 3000K / 4000K / 5700K. Driver efficiency > 85%, power factor > 0.95, THD <10%, Surge Protection 6KV. Pole section welded by certified welders using high end MIG welding processes. PDC aluminium service door 330mm height x 75mm width shall be provided with the company logo embossed on the bottom of the door and safety rope with IP protection rating. The control gear tray is prewired with2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way terminal block for loop-in / loop-out arrangement, 5A 2 Way terminal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 300mm Square x 16mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 48 x 24 to suit M20 x 500mm bolts of grade 4.6 at CC 215. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. Afterfabrication entire pole is shot blasted (Inhouse). The pole is coated with epoxy zinc phosphate primer and finished using environmentally stable powder coated (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options. Must have inhouse manufacuturing facilities along with powder coating shot blasting machines.KP-7229+KP-9108. Make: K- Lite/Ligman/Unilamp |
| 152 | Supply of 45-50W Post top with LED 3000K, 4000K, 5700K 240Vac CRI >80 MacAdam step 3 Dimension not less than Ø400 x 807 mm, Light Distribution 360° Electronic driver ON/OFF, IP rating IP65/66, Spun aluminium top cover Ø400 mm of 1.6mm thickness, die cast aluminium decorative knob on top, Mild steel ( Sand Blasting with zinc primer supporting arm integrated with die-cast aluminium base suitable for mounting Ø76mm OD pipe. SS fasteners. Pure polyester powder coated process : Acid treatment & pure polyester powder coating. Clear acrylic diffuser with controlled downward light emission. Lamp fixed position. Lumen efficacy should be minimum 120lm/W. This luminaire should contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire L70B10>50,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency>88%, power factor >0.96, THD <10%, Surge protection 6KV .the fixtures proposed must have passed LM 79 & LM- 80, latest Reports will be submitted post the issuance of LOA to the successful bidder and before the supply of material, Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN CE& BIS Certified manufactrurer must have inhouse NABL certified labs. Make: K-Lite/Ligman/Unilamp |
| 153 | Supply of Post top Lighting Pole of 4m-4.2m Height made out MS Pipe Ø76.1mm confirming to YSt 210 and facilitating the luminaire mounting at the top. The pole shall be surfacemounted on a pre-formed foundation. The base plate of the of the pole shall be E 250 grade MS 200 mm x 200mm, 12mm thick confirming to IS2062:2011 shall be facilitated with elongated slots to suit the 300mm, J-type, M16 bolts, Grade 4.6 that shall be provided with suitable nuts and plain washers. The structurally sound pole emerging out of the base plate shall be architecturally designed with a decorative cast aluminium causeway base cover Ø330mm x 806mm(H), The grade of pressure diecast material shall be ADC12. A GDC embellishment is provided at appropriate height enhancing the decorative outlook of the pole. The grade of gravity die cast material shall be LM6. The Pole welding shall be done with certified welders using a V groove technique with a high end MIG welding process. A base compartment with a die cast aluminium door contoured to the poles's shape housing the gear tray, prewired with 2 way connector The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thoroughremoval of impuritise like, rust, oxides and other unwanted particles from the suface for high standard coating.The surface finish of the pole shall be Zinch rich primer coat & pure polyester powder coating or epoxy zinc phosphate primer followed by the environmentally stable Polyurethane based paint. Any other wiring/electrical consumables shall be under the scope of purchaser.Manufacuturer must have inhouse shot blasting and powder coating facilities. Make: K-Lite/Ligman/Unilamp |
| 154 | Supply of Input power : 6W surface mounted compact spot light designed to provide directional light. Beam angle 15° / 25° / 40°. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. Clear toughened glass of 4mm thickness.Surface mounting spike made of polypropylene black. Hybrid optics with lens & mirror finish pure aluminium reflector combination for higher efficiency, lower optical losses with optimum glare suppression. Swivel range of 0° - 90°. Single cable entrance M10 cable gland. Protection class IP65/66. Mechanical resistance IK06. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. K- Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminaire dimension : 101 x 64 x 93mmt. All tolerance should be ±15% , Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, CE & BIS Certified. Make: K-Lite/Ligman/Unilamp |
| 155 | Supply, laying, fixing Ladder and perforated type Cable Trays shall be manufactured as per IS /IEC 61537 and it shall be of Pre Galvanized bolted type and factory fabricated out of CRCA sheet with standard accessories like tees- Horizontal and Vertical, Circular bends- Horizontal and Vertical, Coupler plates, Reducers, 4-way cross, Tray covers, Fasteners. etc. for different loads and number and size of cables as given below. All indoor type cable trays shall be galvanized according to BS EN /IEC 10346 with 275 GSM and All outdoor type cable trays shall be Hot dip galvanized according to DIN EN ISO 1461 with 60 microns. 750mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 156 | 600mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 157 | 450mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 158 | 300mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 159 | 150mm x 50mm x 3mm Runners 20 x 150 x 20 x 2.5 mmRungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 160 | Providing & fixing 50mm x 50mm x 5mm GI angle suspenders & base supports for ladder cable trays upto 1500mm with all necessary fixing accessories. |
| 161 | Providing & fixing 40mm x 40mm x 5mm GI angle suspenders & base supports for ladder cable trays upto 900mm with all necessary fixing accessories. |
| 162 | Providing & fixing 32mm x 32mm x 5mm GI angle suspenders & 40mm x 40mm x 5mm base supports for ladder cable trays of size 750mm & 600mm with all necessary fixing accessories. |
| 163 | Providing & fixing 25mm x 25mm x 5mm GI angle suspenders & 40mm x 40mm x 5mm base supports for ladder cable trays of size 450mm & below with all necessary fixing accessories. |
| 164 | Supplying and installing following size of perforated pre-painted M.S cable trays with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6mm thickness |
| 165 | 150 mm width X 50 mm depth X 1.6mm thickness |
| 166 | 300 mm width X 50 mm depth X 1.6mm thickness |
| 167 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 168 | 600 mm width X 50 mm depth X 2.0mm thickness |
| 169 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 170 | Supplying and installing following size of perforated pre-painted M.S cable trays bends with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6mm thickness |
| 171 | 150 mm width X 50 mm depth X 1.6mm thickness |
| 172 | 300 mm width X 50 mm depth X 1.6mm thickness |
| 173 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 174 | 600 mm width X 50 mm depth X 2.0mm thickness |
| 175 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 176 | Supplying and installing following size of perforated pre-painted M.S cable trays reducers with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6mm thickness |
| 177 | Supplying and installing following size of perforated pre-painted M.S cable trays reducers with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6mm thickness |
| 178 | Supplying and installing following size of perforated pre-painted M.S cable trays reducers with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6mm thickness |
| 179 | Supplying and installing following size of perforated pre-painted M.S cable trays reducers with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness |
| 180 | Supplying and installing following size of perforated pre-painted M.S cable trays reducers with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 600 mm width X 50 mm depth X 2.0mm thickness |
| 181 | Supplying and installing following size of perforated pre-painted M.S cable trays reducers with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 182 | Supplying and installing following size of perforated pre-painted M.S cable trays Tee's with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6mm thickness |
| 183 | Supplying and installing following size of perforated pre-painted M.S cable trays Tee's with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6mm thickness |
| 184 | Supplying and installing following size of perforated pre-painted M.S cable trays Tee's with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6mm thickness |
| 185 | Supplying and installing following size of perforated pre-painted M.S cable trays Tee's with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required.450 mm width X 50 mm depth X 2.0 mm thickness |
| 186 | Supplying and installing following size of perforated pre-painted M.S cable trays Tee's with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 600 mm width X 50 mm depth X 2.0mm thickness |
| 187 | Supplying and installing following size of perforated pre-painted M.S cable trays Tee's with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 188 | Supplying and installing following size of perforated pre-painted M.S cable trays Cross members with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6mm thickness |
| 189 | Supplying and installing following size of perforated pre-painted M.S cable trays Cross members with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6mm thickness |
| 190 | Supplying and installing following size of perforated pre-painted M.S cable trays Cross members with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6mm thickness |
| 191 | Supplying and installing following size of perforated pre-painted M.S cable trays Cross members with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness |
| 192 | Supplying and installing following size of perforated pre-painted M.S cable trays Cross members with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 600 mm width X 50 mm depth X 2.0mm thickness |
| 193 | Supplying and installing following size of perforated pre-painted M.S cable trays Cross members with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts&nuts, painting suspenders etc as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 194 | Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required |
| 195 | Supply, installation, testing & commissioning of One Set of 20 KVA UPS. Each UPS of 20 KVA should have following specifications in addition to tender requirements : (i) True online double conversions, IGBT Rectifier & inverter based UPS. (ii) Three phases Input/ three phase output (Input Line Voltage: 340 - 478 Volt, 3 phase, Output Line Voltage 400 volt, 3 phase) (iii) SMF batteries complete with MS Fabricated battery rack to accomodate the complete battery system. (iv) Suitable for 30 Min backup on Full load at 0.8 Load P.F., with required nos. of Battery with each UPS. (v) Output THD is less than 3% for full linear load & Less than 5 % for nonlinear load. (vi) Crest factor 3:1(vii) over load 125% for 10 min, 150% for 1 min and should be able to operate continuously at 115% load on bypass mode. (viii) Battery type should be Valve regulated lead-acid (VRLA). (ix) Inbuilt / External Isolation Transformer, parallel communication port, RS232, USB, EPO and SNMP interface, BMS interface. (x) Dust Filter at Air Inlet point are required. (xi) UPS should be provided with environment monitoring probe to measure temperature and humidity of UPS room on SNMP card software. (xii) LCD Display indicating all important parameters. (xiii) UPS shall be provided with Temperature and Humidity Sensors to monitor Temperature and Humidity over LAN.(xiv) Battery open rack with top cover, battery interlinks and battery breaker. (xv) Battery to UPS cable as required should be provided with UPS systems. (xvi) UPS system shall be parallelable upto 6 units in case required in future. (xvii) Each UPS shall be compatible for working in parallel redundant mode with other. |
| 196 | (Supply, installation, testing & commissioning of One Set of 15 KVA UPS. Each UPS of 15 KVA should have following specifications in addition to tender requirements : (i) True online double conversions, IGBT Rectifier & inverter based UPS. (ii) Three phases Input/ three phase output (Input Line Voltage: 340 - 478 Volt, 3 phase, Output Line Voltage 400 volt, 3 phase) (iii) SMF batteries complete with MS Fabricated battery rack to accomodate the complete battery system. (iv) Suitable for 30 Min backup on Full load at 0.8 Load P.F., with required nos. of Battery with each UPS. (v) Output THD is less than 3% for full linear load & Less than 5 % for nonlinear load. (vi) Crest factor 3:1 (vii) over load 125% for 10 min, 150% for 1 min and should be able to operate continuously at 115% load on bypass mode. (viii) Battery type should be Valve regulated lead-acid (VRLA). (ix) Inbuilt / External Isolation Transformer, parallel communication port, RS232, USB, EPO and SNMP interface, BMS interface. (x) Dust Filter at Air Inlet point are required. (xi) UPS should be provided with environment monitoring probe to measure temperature and humidity of UPS room on SNMP card software. xii) LCD Display indicating all important parameters. (xiii) UPS shall be provided with Temperature and Humidity Sensors to monitor Temperature and Humidity over LAN. (xiv) Battery open rack with top cover, battery interlinks and battery breaker. (xv) Battery to UPS cable as required should be provided with UPS systems. (xvi) UPS system shall be parallelable upto 6 units in case required in future. (xvii) Each UPS shall be compatible for working in parallel redundant mode with other. |
| 197 | Rising Main , Supplying, installation on wall, testing and commissionioning of following capacity Air insulated compact rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convient sections complete with 4 Nos.aluminium bus bars having current density 130A/sq cm at nominal current rating, necessary joints & expansion joints, fire barrier at each floor, provision of tapping at every meter, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc.as required. 630A, Isc=35KA for 1 Sec |
| 198 | Rising Main,Supplying, installation on wall, testing and commissionioning of following capacity Air insulated compact rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convient sections complete with 4 Nos.aluminium bus bars having current density 130A/sq cm at nominal current rating, necessary joints & expansion joints, fire barrier at each floor, provision of tapping at every meter, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc.as required. 315A, Isc=25KA for 1 Sec |
| 199 | Supplying, installation on wall, testing and commissionioning of following capacity Air insulated compact rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convient sections complete with 4 Nos.aluminium bus bars having current density 130A/sq cm at nominal current rating, necessary joints & expansion joints, fire barrier at each floor, provision of tapping at every meter, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc.as required. 500A, Isc=35KA for 1 Sec |
| 200 | Supplying, installation on wall, testing and commissionioning of following capacity End feed unit for the existing Air Insulated Compact type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with 1.6mm thick steel enclosure (IP-54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 500A, Isc=35KA for 1 Sec |
| 201 | Supplying, installation on wall, testing and commissionioning of following capacity End feed unit for the existing Air Insulated Compact type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with 1.6mm thick steel enclosure (IP-54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 630A, Isc=50KA for 1 Sec |
| 202 | Providing and fixing following rating and breaking capacity and pole MCCB/ACB with thermonagnetic/microprocessor release and terminal spreaders in existing cubival panel board including drilling holes in cubical panel, making connections, etc. as required. 125A, Isc=36KA,FP,MCCB |
| 203 | Providing and fixing following rating and breaking capacity and pole MCCB/ACB with thermonagnetic/microprocessor release and terminal spreaders in existing cubival panel board including drilling holes in cubical panel, making connections, etc. as required. 200A, Isc=36KA,FP,MCCB |
| 204 | Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing air insulated compact type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50 Hz A.C. supply made with provision of MCCB/ACB (but without MCCB/ACB) complete etc.as required 125A, Isc=15KA for 1 Sec |
| 205 | Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing air insulated compact type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50 Hz A.C. supply made with provision of MCCB/ACB (but without MCCB/ACB) complete etc.as required 200A, Isc=25KA for 1 Sec |
| 206 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc in ground including welding excavation and Providing cement concrete blocks as supports anticorrosive treatment with coaltar / asphalts tape as per IS :10221 refilling the trench etc of following sizes complete as required .150 mm dia |
| 207 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 25 mm dia |
| 208 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required .32 mm dia |
| 209 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 40 mm dia |
| 210 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 50 mm dia |
| 211 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 65 mm dia |
| 212 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 80 mm dia |
| 213 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 100 mm dia |
| 214 | Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 150 mm dia |
| 215 | Supplying and Fixing Single Headed Internal Hydrant Valve with instantaneous gunmetal coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS : 5290 ( Type A ) with blank gunmetal material cap and chain as required .Single Headed Gunmetal Material |
| 216 | Supplying Fixing Testing and Commissioning of butterfly valve of PN 1.6 Rating with Bronze Gunmetal Sheet duly ISI marked complete with nuts , bolts , washers , gaskets conforming to IS : 13095 of following sizes as required .80 mm dia |
| 217 | Supplying Fixing Testing and Commissioning of butterfly valve of PN 1.6 Rating with Bronze Gunmetal Sheet duly ISI marked complete with nuts , bolts , washers , gaskets conforming to IS : 13095 of following sizes as required .100 mm dia |
| 218 | Supplying Fixing Testing and Commissioning of butterfly valve of PN 1.6 Rating with Bronze Gunmetal Sheet duly ISI marked complete with nuts , bolts , washers , gaskets conforming to IS : 13095 of following sizes as required . 150 mm dia |
| 219 | Supplying and Fixing orifice plate made out of 6 mm thick stainless steel ( Grade 304 ) with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg / sqcm complete as required . |
| 220 | Providing Installation Testing and Commissioning of Non Return Valve of following sizes conforming to IS : 5312 complete with rubber gasket , GI Bolts , Nuts , washers etc as required 100 mm dia |
| 221 | Providing Installation Testing and Commissioning of Non Return Valve of following sizes conforming to IS : 5312 complete with rubber gasket , GI Bolts , Nuts , washers etc as required 150 mm dia |
| 222 | Supplying and Fixing 63 mm dia 15 m Long RRL Hose pipe with 63 mm dia male and female coupling duly bound with GI wire , rivet etc . Conforming to IS : 636 ( Type A ) as Required . Gunmetal Material |
| 223 | Supplying and Fixing First aid hose reel with MS Construction Spray painted in Post office red conforming to IS : 884 complete with the following as required20 mm nominal internal dia water hose thermoplastic ( Textile Reinforced ) Type - 2 as per IS : 12585 20 mm nominal internal dia gunmetal globe valve and nozzle Drum and Brackets for fixing the equipments on wall Connections from Riser with 25 mm dia stop gunmetal valve and MS Pipe and socket 40 Metre Length |
| 224 | Supplying and Fixing 63 mm dia Gunmetal Material Short Branch Pipe with 20 mm nominal internal diameter size nozzle conforming to IS : 903 suitable for instantaneous connection to interconnect hose pipe coupling as required Gunmetal Material |
| 225 | Supplying and Fixing of Fire brigade connection of Cast iron body with gunmetal male intantaneous inlet coupling complete with cap and chain as required for suitable dia ms pipe connection conforming to IS : 904 as required2 Way 100 mm dia MS Pipe |
| 226 | Supplying and Fixing Air Vessel made of 250 mm dia 8 mm thick ms sheet 1200 mm in height with air release valve on top and flanged connection to riser drain arrangement with 25 mm dia gunmetal wheel valve with required accessories pressure gauge and painting with synthetic enamel paint of approved shade as required |
| 227 | Providing , Fixing , Testing and Commissioning of 15 mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories . Upright Sprinkler |
| 228 | Providing and Fixing Flow Switches of following sizes MS Pipe including connection etc as required .100 mm dia |
| 229 | Providing and Fixing Flow Switches of following sizes MS Pipe including connection etc as required . 150 mm dia |
| 230 | Supply , Installation , Testing and Commissioning of Sprinkler Flexible pipe ( UL Listed ) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI ( Burst ) with branch line ( Inlet ) 25 mm NPT male thread to sprinkler head ( outlet ) 15 mm NPT female thread with reducer , nipple , 2 side brackets , center bracket , stock bar of following sizes complete as required .1500 mm Length |
| 231 | Supplying , Installation , Testing and Commissioning of deluge valve ( to be used for water curtains ) UL listed with wet pilot basic trim assembly for DVA with test and alarm , drip and drain valve with water motor gong complete as required .150 mm dia |
| 232 | Providing , Installation , Testing and Commissioning of water curtain nozzles 15 mm dia nickel chrome plated brass , BSPT , K factor as per design consideration complete as required . |
| 233 | Providing , Installation , Testing and Commissioning of electric release trim assembly for deluge valve with two way solenoid valve , weather proof operation on 24 volts DC supply complete as required . |
| 234 | Providing and fixing of Fire Hose Cabinet size not less than 2.1 x 1.2 x 0.90 mtr made out of M.S. sheet not less than 1.5 mm thick having central opening and 4 mm thick glazed glass doors (Two nos.) suitably marked on the outside 'with the letters \\"FIRE HOSE\\" including necessary locking arrangement and painting in PO red colour suitable to accommodate, internal hydrant valve, 2 nos 15 mtr long Hose pipe, branch pipe, nozzle and fire man's axe. It shall be fixed inside the FHC Cabinet Complete as required . |
| 235 | Providing and fixing standard firemans axe with heavy rubber handle. |
| 236 | Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebration 0-16 / sq. cm. |
| 237 | Providing and fixing Fire Extinguishers (CO2 type powder ) 4.5 Kg Capacity complete with all accessories as per manufacturers specifications. |
| 238 | Providing and fixing Fire Extinguishers (A, B, C type powder ) 6 Kg Capacity complete with all accessories as per manufacturers specifications. |
| 239 | Providing and fixing Fire Extinguishers (WATR CO2 Type) 9 Kg Capacity complete with all accessories as per manufacturers specifications. |
| 240 | Providing and fixing Fe 36 automatic Fire Extinguishers 10 Kg Capacity complete with all accessories as per manufacturers specifications. |
| 241 | Providing and fixing 25 mm dia Inspector Test Valve 25 mm with drain arrangement complete with all accessories as per manufacturers specifications. |
| 242 | Supplying, installation, testing and commissioning of electric driven Terrace Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : ( Terrace Fire Pump ).Horizontal type, multistage, centrifugal split casing pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head |
| 243 | Supplying,Installation,testing & commissioning of dust & vermin proof double door with canopy type taperd roof wall / floor mounted compartmentlised feeder piller type cubical control Panel for fire fighting terrace pump of front area not less than 1.0 Sqmtr. and depth not less than 300 mm, made out of 2mm thick CRCA sheet with 100 Amp. 4 strip aluminium bus bars with front openable door & locking arrangement, interconnection, control wiring, intrigation with pressure switch i/c suppying & fixing following switchgears & control gears/starters etc. as required.Incomming100 Amps. 16ka breaking capacity 4 pole MCCB-1 Nos.Voltmeter (0-500 Volt) with selector switch.-1 Nos.Ammeter (0-100 Amps.) with selector switch -1 Nos.Set of 3 phase indication lamp-1 Set100 Amps. 4 strip insulated bus bars-1 Nos.Outgoing 63 Amps. 10ka breaking capacity 3 pole MCCB--2 Nos.Ammeter (0-60 Amps.) with selector switch-2 Nos.Suitable HP fully automatic Star/Delta Starter with over load protection, current sensing type single phase preventor complete with all accessories and internal wiring required for automatic operation.- 2 SetSelector switch for local/remote, auto/manual/off operation ON/OFF indication etc.- 2 Set complete in all respect. |
| 244 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. It should be complete as per specifications & directions of Engineer-in-charge. 4 x 25 sqmm ( 28 mm ) |
| 245 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.150 mm width x 50mm depth x 1.6 mm thickness. |
| 246 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 247 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 248 | Supplying & laying one number XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI /Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred. 4 core, 25 sq.mm. Aluminium Armoured |
| 249 | Supply and fixing in position 1 m wide Insulation mat made of elastomeric polymers Material (Class -A) of 415V grade as per IS 15642-2006 . Thickness of insulation mat shall be not less than 2 mm to withstand 1.1 KV dielectric strength AS PER IS 15652 : 2006. It should be complete as per specifications & directions of Engineer-in-charge. |
| 250 | Supply, installation, testing & commissioning of Solar Water Heating System of 80 NOS ISI Marked Solar Flat Plate Collectors of size 2080mm X 1070mm X 100mm,, Laser welded . with necessary Stands, Support etc. with 8000 Ltrs capacity SS -304 hot water storage tank of thickness 4 mm duly insulated with 50 mm thick PUFF insulation & 24 SWG Aluminium Cladding, with Heat Exchanger of suitable surface area, with necessary makeup tank, with 50 KWH Electrical backup for cloudy / foggy days, with necessary piping with solar panels & solar hot water tank, with one No. temperature Gauge, with 01 Nos. Ball valves, to produced hot water up to 60 degree C on clear sunny days. (MNRE Approved) |
| 251 | Supply, installation, testing & commissioning of Solar Water Heating System of 50 NOS ISI Marked Solar Flat Plate Collectors of size 2080mm X 1070mm X 100mm,, Laser welded . with necessary Stands, Support etc. with 5000 Ltrs capacity SS -304 hot water storage tank of thickness 4 mm duly insulated with 50 mm thick PUFF insulation & 24 SWG Aluminium Cladding, with Heat Exchanger of suitable surface area, with necessary makeup tank, with 50 KWH Electrical backup for cloudy / foggy days, with necessary piping with solar panels & solar hot water tank, with one No. temperature Gauge, with 01 Nos. Ball valves, to produced hot water up to 60 degree C on clear sunny days. (MNRE Approved) |
| 252 | Sewage Treatment Plant at fulsungi site |
| 253 | SITC of Sewage Treatment Plant 132 KLD MBBR Based Under ground RCC Tanks Sewage treatment plant-MBBR technology ( with air diffuser system) with sewage handling capacity of 132 KL per day. The raw sewage collection sump with double SS bar screen shall be part of STP. STP shall be designed as water retaining structure, . Including necessary chemical dosing as required by the manufacturer's design. All the equipments, pipings, pumps, blowers and electricals are to be housed in a plant room at Ground level. Including GI Puddle flanges (with hot dip galvanizing) inlet,outlet, overflow, vent, C.I. Manhole covers, drain channels with MS(painted) gratings.Contractor to exclude all civil works like construction of equalization tank,civil works for pump room,etc.All STP compartments(except equalization tank),pumps ,equipments shall be placed Above Ground level. Construction of Underground RCC STP Tanks is not in the scope of work of STP contractor. The STP shall be designed based on the following parameters: for irrigation purpose. Flow Rate - 125 KL/day-MBBR technology pH - 7-9 BOD - 250 - 300 mg/lt. COD - upto 600 mg/lt. SS - upto 400 mg/lt. Oil ,Grease and ABS - upto 75 mg/lt. Ecoli MPN/100ML - 1000000The treated sewage shall have following characteristics: pH - 7.0 - 7.5 BOD -less than 30 mg/lt. COD -less than 50 mg/lt. SS - Less than 20 mg/lt. Oil & Grease and ABS - less then 5mg/lt.Ecoli MPN/100ML - 1000 Bar Screen Size : 600 x 800MOC : SS 304Qty : 01 Nos Complete in all respect |
| 254 | Raw Sewage Transfer Pumps SITC of Bar Screen Size : 600 x 800MOC : SS 304Qty : 01 Nos X Head = 10 Mtr Qty = 02 Nos (1W + 1SB |
| 255 | Sludge Re-circulation Pumps Flow rate (each) =9000 lphHead = 10 Mtr Qty = 02 Nos (1W + 1SB) Make:- Kirloskar, Leo, Lubi |
| 256 | Sump Pumps for plant room drainage Flow rate (each) =4000 lphHead = 10 Mtr Qty = 02 Nos (1W + 1SB) Make:- Kirloskar, Leo, Lubi |
| 257 | Centifuse Feed Pump Flow rate (each) = 9000 lph Head = 20 Mtr Qty = 02 Nos ( 1W + 1SB) Make:- Kirloskar, Leo, Lubi |
| 258 | SITC of Air diffusion system :(Air Blower) 2 Nos. (one working & one standby) capable of delivering 75 m3 of free air each at 4500 MMWG driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP suitable for 415 ± 10% volts, 3 phase, 50 cycles A.C. supply.- 1 Set |
| 259 | UPVCI/MS(heavy Class) conforming to IS:1239- 1982 complete with UPVC fittings ® brand such as tees, crosses, |
| 260 | Flexible pipes complete with stainless steel fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good for submerged air piping. |
| 261 | SITC of Air Distribution Systems Membrane Air Defuser, Disc Type Pipe line and related accessories |
| 262 | Centrifuge Basket for Sludge Management & disposal. |
| 263 | Filter Feed Pumps Flow rate (each) = 9000 lph Head = 30 Mtr Quantity = 02 Nos (1W / 1S) Make:- Kirloskar, Leo, Lubi |
| 264 | Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP pressure sand multigrade filter(shell 6mm & dished ends 8mm)with Frontal Piping, 5 Valve Battery. Filters shall be suitable for flow rate of 10000 LPH at 3.5 Kg/Sqcm working pressure. |
| 265 | Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP Activated Carbon filter (shell 6mm & dished ends 8mm)with Frontal Piping, 5 Valve Battery. Filters shall be suitable for flow rate of 10000 LPH at 3.5 Kg/Sqcm working pressure |
| 266 | MS Header & running pipe UPVC complete with UPVC fittings ® brand such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good including coating the pipes with desired shade of colour coding over a coat of primer piping before tertiary treatment. - 1 Set. (Make Supreme/prince). |
| 267 | Providing & Fixing of MBBR Media Complete in all respect |
| 268 | Providing & Fixing of Tube Settler MediaPVC Tube Media of 750 mm height .Complete in all respect |
| 269 | Supply Installation, testing & commissioning of Electrical Panel suitable for 415 V, 3 Phase, 4 wies, 50Hz power distribution system. The panel shall be free standing floow / wall mounted, sheet metal enclosed flush front dust & venim proof with Aluminium bus bars. The painting shall be done as per relevant ISI codes as specified. Adequate size cable alley shall be provided for each cable bending & termination. (All components would be L&T/Schnieder /GE). Including electrical wiring for electrical connection of equipments.with cable trays ets.complete. |
| 270 | Providing & fixing Skid Miunted ultra filtration System For Flushing Water |
| 271 | Supply, installation, testing & commissioning of chlorine dosing system consisting of one FRP/ HDPE tank of 100 liters capacity with a positive displacement diaphragm Dosing pump with a variable flow rate of 0-6LPH. The motor shall be suitable for operation at 240 V /one phase/ 50 Hertz supply. The pump shall be supplied complete with necessary poly propylene piping, valves, strainers & injection fittings for system to dose solution to the feed line. The pump shall be Asia LMI make. (Location : Pump Room for STP). |
| 272 | Sewage flow Measurement - Electro Magnetic type flow measurement for output Sewage flow. -1nos. Level Switch - Equalisation tank, filter feed tank Sludge holding tank & treated water tank.-4 nos.Make : Electronet Online PH meter - Online after ACF-1no. Make : Aster Digital Energy meter - Panel Mounted-1no. |
| 273 | Providing & fixing Digital water meter complete with all internal fittings/accessories,making connection with water supply pipe including all fittings on pipes of following diameter. |
| 274 | Sewage Treatment Plant at Transit Site |
| 275 | SITC of Sewage Treatment Plant 60 KLD MBBR Based Under ground RCC Tanks Sewage treatment plant-MBBR technology ( with air diffuser system) with sewage handling capacity of 60 KL per day. The raw sewage collection sump with double SS bar screen shall be part of STP. STP shall be designed as water retaining structure, . Including necessary chemical dosing as required by the manufacturer's design. All the equipments, pipings, pumps, blowers and electricals are to be housed in a plant room at Ground level. Including GI Puddle flanges (with hot dip galvanizing) inlet,outlet, overflow, vent, C.I. Manhole covers, drain channels with MS(painted) gratings.Contractor to exclude all civil works like construction of equalization tank,civil works for pump room,etc.All STP compartments(except equalization tank),pumps ,equipments shall be placed Above Ground level. Construction of Underground RCC STP Tanks is not in the scope of work of STP contractor. The STP shall be designed based on the following parameters: for irrigation purpose. Flow Rate - 125 KL/day-MBBR technology pH - 7-9 BOD - 250 - 300 mg/lt. COD - upto 600 mg/lt. SS - upto 400 mg/lt. Oil ,Grease and ABS - upto 75 mg/lt. Ecoli MPN/100ML - 1000000 The treated sewage shall have following characteristics: pH - 7.0 - 7.5 BOD -less than 30 mg/lt.COD -less than 50 mg/lt. SS - Less than 20 mg/lt. Oil & Grease and ABS - less then 5mg/lt. Ecoli MPN/100ML - 1000 Bar Screen Size : 400 x 600 MOC : SS 304 Qty : 01 Nos complete in all respect. |
| 276 | Providing & fixing of Raw Sewage Transfer Pumps Flow rate (each) = 9000 lph Head = 10 Mtr Qty = 02 Nos (1W + 1SB) Make:- Kirloskar, Lubi,Leo Complete in all respect. |
| 277 | Providing % fixing of Sludge Re-circulation Pumps Flow rate (each) =9000 lph Head = 10 Mtr Qty = 02 Nos (1W + 1SB) Make:- Kirloskar, Leo, Lubi complete in all respect |
| 278 | Providing & fixing of Sump Pumps for plant room drainage Flow rate (each) =4000 lph Head = 10 Mtr Qty = 02 Nos (1W + 1SB) Make:- Kirloskar, Leo, Lubi complete in all respect |
| 279 | Providing & fixing of Centifuse Feed Pump Flow rate (each) = 9000 lph Head = 20 Mtr Qty = 02 Nos ( 1W + 1SB) Make:- Kirloskar, Leo, Lubi Complete in all respect |
| 280 | Providing & fixing of Air diffusion system :(Air Blower) 2 Nos. (one working & one standby) capable of delivering 75 m3 of free air each at 4500 MMWG driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP suitable for 415 ± 10% volts, 3 phase, 50 cycles A.C. supply.- 1 Set Complete in all respect |
| 281 | Providing & fixing of UPVCI/MS(heavy Class) conforming to IS:1239- 1982 complete with UPVC fittings ® brand such as tees, crosses, Complete in all respect |
| 282 | Providing & fixing of Flexible pipes complete with stainless steel fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good for submerged air piping. Complete in all respect |
| 283 | Providing & fixing of Membrane Air Defuser, Disc Type Pipe line and related accessories Complete in all respect |
| 284 | Providing & fixing of Centrifuge Basket for Sludge Management & disposal. Complete in all respect |
| 285 | Providing & fixing of Filter Feed Pumps Flow rate (each) = 9000 lph Head = 30 Mtr Quantity = 02 Nos (1W / 1S) Make:- Kirloskar, Leo, Lubi Complete in all respect |
| 286 | Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP pressure sand multigrade filter(shell 6mm & dished ends 8mm)with Frontal Piping, 5 Valve Battery. Filters shall be suitable for flow rate of 10000 LPH at 3.5 Kg/Sqcm working pressure. |
| 287 | Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP Activated Carbon filter (shell 6mm & dished ends 8mm)with Frontal Piping, 5 Valve Battery. Filters shall be suitable for flow rate of 10000 LPH at 3.5 Kg/Sqcm working pressure |
| 288 | Providing & fixing of MS Header & running pipe UPVC complete with UPVC fittings ® brand such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good including coating the pipes with desired shade of colour coding over a coat of primer piping before tertiary treatment. - 1 Set. (Make Supreme/prince). |
| 289 | Providing & fixing of MBBR Media Complete in all respect |
| 290 | Providing & fixing of Tube Settler Media PVC Tube Media of 750 mm height . Complete in all respect |
| 291 | Supply Installation, testing & commissioning of Electrical Panel suitable for 415 V, 3 Phase, 4 wies, 50Hz power distribution system. The panel shall be free standing floow / wall mounted, sheet metal enclosed flush front dust & venim proof with Aluminium bus bars. The painting shall be done as per relevant ISI codes as specified. Adequate size cable alley shall be provided for each cable bending & termination. (All components would be L&T/Schnieder /GE). Including electrical wiring for electrical connection of equipments.with cable trays ets.complete. |
| 292 | Providing & fixing Skid Miunted ultra filtration System For Flushing Water Complete in all respect |
| 293 | Supply, installation, testing & commissioning of chlorine dosing system consisting of one FRP/ HDPE tank of 100 liters capacity with a positive displacement diaphragm Dosing pump with a variable flow rate of 0-6LPH. The motor shall be suitable for operation at 240 V /one phase/ 50 Hertz supply. The pump shall be supplied complete with necessary poly propylene piping, valves, strainers & injection fittings for system to dose solution to the feed line. The pump shall be Asia LMI make. (Location : Pump Room for STP). |
| 294 | Providing & fixing of Sewage flow Measurement - Electro Magnetic type flow measurement for output Sewage flow. -1nos. Level Switch - Equalisation tank, filter feed tank Sludge holding tank & treated water tank.-4 nos. Make : Electronet Online PH meter - Online after ACF-1no. Make : Aster Digital Energy meter - Panel Mounted-1no. |
| 295 | Providing & fixing Digital water meter complete with all internal fittings/accessories,making connection with water supply pipe including all fittings on pipes of following diameter.Complete in all respect. |
| 296 | Water Treatment Plant |
| 297 | Providing and fixing Water Treatment Plant for Fulsungi & Transit Site In-line vertical/horizontal centrifugal clear water pump set SS-304 casing, SS-304 impeller, SS-304 shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class \\"F\\" insulation & efficiency class EFF-1, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply (with mechanical seal), motor rating IE-3, pressure gauges with gunmetal isolation cocks, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation including suction header, discharge header, isolation valve & matching companion flanges, etc. complete in all respects and as per speicification with the following capacities: Filter Feed Pump : 1(1W + 1S) Capacity : 250 LPM of Each Pump Head : 25 MNote:-1 set consists of 2 nos. of pumps (1Working + 1Standby) |
| 298 | Providing & fixing of STP Makeup Pump : 1 (1W + 1S) Capacity : 250 LPM of Each Pump Head : 35 MNote:-1 set consists of 2 nos. of pumps (1Working + 1Standby) |
| 299 | Providing and fixing In-line vertical/horizontal centrifugal clear water Hydroneumetic pump set with requitred Acesseries SS-304 casing, SS-304 impeller, SS-304 shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class \\"F\\" insulation & efficiency class EFF-1, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply ( with mechanical seal ), motor rating IE-3, pressure gauges with gunmetal isolation cocks, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation including suction header, discharge header, isolation valve & matching companion flanges, etc. complete in all respects and as per speicification with the following capacities: Domestic water transfer pumps (Hydroneumatic) No. of Pumps : 1 ( 1 Working + 1 Stand by) Capacity : app. 150 LPM eachHead : 70 M approx as per current loaction (complete set as mentioned above) |
| 300 | Providing, fixing, testing & commissioning of vertical MSFRP filter with adequate dirt holding capacity. Fabricated from M.S sheet of minimum 8mm thick for shell & 10mm thick for dished ends,(Quality of Steel as per IS:2062 Grade B, thickness as per ASME Section 8),Tested to 5.0 Kg/m2, complete with intitial charge filter media including painting inside with two coats of non toxic epoxy and with one coat of zinc chromate two coats of synthetic enamel paint outside. Including concrete foudation with cement plaster complete as required. The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping/face piping (heavy duty G.I.) and butterfly valves of suitable diameter as per system parameters designed on 1.50 m / sec velocity & suitable provision of back wash(air blower with air flow approx. 5.1 lpm/sqm air capacity, at 0.5 kg/sqcm pressure) & regeneraion needs to be considered. OBR:-8 hours HOS:-2500 MM, dia. of tank to be selected meeting our technical parameters. Depth of Filter Media:- 750-900 mm deep or as per manufacturer's design. Output water quality to confirmmin. IS 10500 standards.It should be complete as per specifications and directions given by Engineer-in-charge. Dual Media Filter Working pressure 3 Kg/Sq.cm Capacity :250 LPMLocation:- WTP Plant Room |
| 301 | Activated Carbon Filter Working pressure 3 Kg/Sq.cm Capacity :250 LPMLocation:- WTP Plant Room |
| 302 | Providing and fixing ‘Cation’ ION exchange water softener fabricated from minimum 8 mm thick M.S. plate on min. shell and 10 mm thick M.S. plate on dished ends (Quality of Steel as per IS:2062 Grade B, thickness as per ASME Section 8) complete with initial charge of filter media and ION exchange resins, face piping accessories, diaphragm valves of approved specifications, HDPE Brine tank of min. 200 Liters, piping testing and commissioning complete with resins of approved quality and make and regeneration assembly complete with valves, ejector, brine suction valves and piping. (Bidder must indicate type and quantity of resin used and quantity of salt required per regeneration). All internal parts of the softener shall be rubber lined as per approved specifications.Minimum expected rate of flow: App. 250LPM Total soft water to be produced between two regenerations: app. 250 Cu.m Expected raw water hardness : app.600-700 ppmExpected treated water hardness: less than 5 ppm (Zero Commercial Hardness)Max. working pressure : 5 Kg/cm2 |
| 303 | Providing and fixing Salt Saturator assembly (for supply of salt solution) consisting of HDPE/PVC tanks with automatic agitators and all required accessories for holding and supplying salt for softener complete in all respects, including providing and fixing vertical, inline multistage centrifugal pumping set with stainless steel SS-316 L stage casing and SS-316 L impellers with stainless steel shaft and suction & discharge casing . The effective capacity of the system to be of minimum 10% greater than actual salt required for approx. 3 Days with complete structural arrangement including RCC foundation etc. as per instructions of engineer-in-charge and approved fabrication shop drawings.(i) Recommended no. of tanks = 1 Nos.(ii) Total Capacity of each Tank = 500 Liters(complete set as mentioned above) |
| 304 | Providing and fixing chemical dozing system consisting of 2 nos. electronic dosing pumps (1W+1S) of approved make with all accessories, suitable to doze chemical solution upto 1 ppm doze (of Sodium Hypo-chloride solution) to a filtered water flow of 7500 lph. against a pressure of 1.5 kg/cm2 complete with FRP moulded solution holding tank of min. 200 litre with all standard accessories & structural arrangement including suitable foundation bolts & other accessories etc.complete as required and as specified. Note:1 set consists of 2 nos. of pumps(1W+1S) |
| 305 | Providing & fixing of 1/2 full to switch ON the incoming supply of waterLow level (less than 1/5 of total depth) to trigger alarm & switch ON the Filter feed pump |
| 306 | Providing & fixing of he following levels For Treated water tank for.Overflow level to trigger alarm & switch OFF the Filter feed pump 1/2 full to switch ON the Filter feed pumpLow level (less than 1/5 of total depth) to trigger alarm & switch ON the Filter feed pump |
| 307 | Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).(Pumps suitable to handle solids upto 25 mm size with C.I. body, SS304 shaft, C.I. impeller with 15 mtrs cable, double mechanical seal). Pump Room Drainage Pumps -(1W & 1S)Capacity/Flow Rate - 250 LPMHead - 10.0 mApprox. Elec. Load. - 2.0 KW each pumpRPM - 2900MOC - C.I Casing / C.I. Impeller / S.S. ShaftLocation - Pump Room Sump |
| 308 | Providing and fixing reinforced neoprene rubber vibration eliminators/expansion joints (to provide relief from stresses at pipe flanges) suitable for upto 20 kg/cm2 pressure, as per specification of the manufacturers complete as required and as specified complete as per directions of the engineer-in-charge. 80mm dia |
| 309 | Providing and fixing reinforced neoprene rubber vibration eliminators/expansion joints (to provide relief from stresses at pipe flanges) suitable for upto 20 kg/cm2 pressure, as per specification of the manufacturers complete as required and as specified complete as per directions of the engineer-in-charge. 100mm dia |
| 310 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.. 150mm dia |
| 311 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange..200mm dia |
| 312 | Providing and fixing C Class MS pipe puddle flanges of required size with 6mm thick MS plate of required size of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks. 25mm dia pipe, 600mm long with 6 mm MS plate of size 300X300mm |
| 313 | 40mm dia pipe, 600mm long with 6 mm MS plate of size 300X300mm |
| 314 | 50mm dia pipe, 600mm long with 6 mm MS plate of size 300X300mm |
| 315 | 65mm dia pipe, 600mm long with 6 mm MS plate of size 300X300mm |
| 316 | 80mm dia pipe, 600mm long with 6 mm MS plate of size 300X300mm |
| 317 | 100mm dia pipe 600mm long with 6 mm MS plate of size 400X400mm |
| 318 | 150mm dia pipe 600mm long with 6 mm MS plate of size 400X400mm |
| 319 | 200mm dia pipe 600mm long with 6 mm MS plate of size 400X400mm |
| 320 | Providing and fixing M.S. grating and preferably in 600mm long pieces, fabricated with 16x16mm square bars, @ 20mm clear spacing and welded to angle iron 25x25x5mm and placed firmly on angle iron frame of 30x30x5mm with 25x3mm hold fasts approximately 75mm long welded at intervals of 500mm including two or more coats of synthetic enamel paint of approved quality and shade over one coats of primer and set in cement mortar 1:3 (1 cement : 3 coarse sand) complete as per attached details for drain. |
| 321 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 40mm dia |
| 322 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 50mm dia |
| 323 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 65mm dia |
| 324 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 80mm dia |
| 325 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 65mm dia |
| 326 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 80mm dia |
| 327 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 65mm dia |
| 328 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :80mm dia |
| 329 | Kitchen Equipment at Fulsungi Site |
| 330 | Providing & fixing of MILKBOILER/TEABOILER Specification 1. Cap.50Ltrs. 2.S.S.Sheet insulated body with triple jacket 3.The water jacket will be fitted with 2 Kw heating element Complete in all respect. |
| 331 | Providing & fixing of MICROWAVE OVEN SpecificationMicrowave oven specifications typically include a 20-32 liter capacity, 700-1200W output power, and 230-240V, 50Hz input voltage. Common types are Solo (reheat/defrost), Grill (browning/crisping), and Convection (baking/roasting). Key features include stainless steel or ceramic interiors, child safety locks, auto-cook menus, and digital touch controls |
| 332 | Providing & fixing of PICKUP COUNTER WITH OVER SHELFSpecification1. Size 1800X600X850+3002.Top 3 sides, under & over shelf of s.s.sheet, on m.s.angle & s.s.tubular legs frame work.3. The counter will have 3 sides fully covered, operator side open Complete in all respect. |
| 333 | Providing & fixing of WORK TABLE FOR SUPPORT OF TWO BURNER RANGESpecification1. Size 1350x600x850mm.2. Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining Complete in all respect. |
| 334 | Providing & fixing of TWO BURNER COOKING RANGESpecification. App. Size 1200X600X850mm or features heavy-duty stainless steel (SS 202/304) construction, high-pressure/low-pressure LPG burners, and individual controls with pilot lights. Typical specifications include a splash-back, cast iron pan supports, undershelves, and dimensions around 48\\"–60\\" length, 24\\"–30\\" width, and 34\\"–36\\" working height Complete in all respect. |
| 335 | Providing & fixing of EXHAUST HOOD (Without Ducting Fixing & Extraction fan)FOR TWO BURNER RANGESpecification1. Size 1950x750x600mm 2. Made of s.steel sheet, 20G thick duly welded & pop 2anitar as requiredComplete in all respect. |
| 336 | JUICER (table top model) Specification1. Cast Aluminum/CI body, duly polished / painted, with worm & perforated insert. Top feedingtray. Worm easily cleanable fitted with 1/2HP elect. motor. Complete in all respect. |
| 337 | Providing & fixing of CONVEYOR TOASTERSpecification1.App. Cap. 100-125 Toasts/hr.2.S.S.Sheet body, having s.s.sheet conveyor belt. App.225mm wide. The unit will have heating elements on top & lower portion of conveyor belt with variable heat &speed control switch. Complete in all respect. |
| 338 | Providing & fixing of WORK TABLE WITH SINKSpecification1.Size 1950x600x850+1502. Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion. Complete in all respect. |
| 339 | Providing & fixing of FOUR DOOR REFRIGERATORSpecification1.Size 1950x600x850+1502. Double walled, insulated ‘PUF’ body made of 0.8mm thick s.s.sheet3. The unit will have 4 doors with magnatic rubber gascuts & locking provision Complete in all respect. |
| 340 | Providing & fixing of WORK TABLESpecification1.Size 1500X600X850mm2. Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Complete in all respect. |
| 341 | Providing & fixing of THREE BURNER COOKING RANGESpecification1.SIZE 1800X600X8502. Structure made of m.s. angle of size 38x38x5mm,duly rust proof painted.3. Top of 16Swg thick s.s.sheet Complete in all respect. |
| 342 | Providing & fixing of LOW HT.TABLE 3anitary3rting low height burner Specification1.Size 750x750x600mm2. Specification same as that of work table but the table will be without undershelf & will have cross bracing support at lower portion. Complete in all respect. |
| 343 | Providing & fixing of LOWHT. BURNERSpecification1.Size 750x750x600mm2.Specification same as that of cooking range but the unit will be without undershelf, but will only have cross bracingsupport at lower portion. Complete in all respect. |
| 344 | Providing & fixing of EXHAUSTHOOD(With out Ducting Fixing & Extractionfan)for LOWHEIGHT BURNER range Specification1.Size 1650x750x600mm2.Made of s.steel sheet, 20G thick duly welded & pop 3anitar as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s. |
| 345 | Providing & fixing of THREE BURNER COOKING RANGESpecification1. O/S 1800X600X8502.Structure made of m.s. angle of size 38x38x5mm, duly rust proof painted3. Top of 16Swg thick s.s.sheet Complete in all respect. |
| 346 | Providing & fixing of WORK TABLE FOR SUPPORT OF 03 BURNER COOKINGRANGESpecification1.Size 1500X600X850mm2.Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required. Complete in all respect. |
| 347 | Providing & fixing of EXHAUSTHOOD(With out Ducting Fixing &Extractionfan)for THREE BURNER RANGESpecification1. Size 1950x750x600mm2.Made of s.steel sheet, 20G thick duly welded & pop 3anitar as required. Complete in all respect. |
| 348 | Providing & fixing of BULKCOOKER/boiler TILTING TYPESpecification. A Tilting Type Bulk Cooker/Boiler is a high-capacity commercial cooking unit, typically made of 304-grade stainless steel with a 160–200+ liter capacity. It features a, manual or geared tilting mechanism, heavy-duty LPG burners or electric induction heatingComplete in all respect. |
| 349 | Providing & fixing of BULK FRYER TILTING TYPE Cap.100Ltrs.Specification1.Cap.100Ltrs2.Triple jacketed body of stainless steel sheet Complete in all respect. |
| 350 | Providing & fixing of EXHAUST HOOD (Without Ducting Fixing & Extraction fan)for BULK COOKER & FRYER Size 1650x750x600mm Specification1.Size 1650x750x600mm 2.Made of s.steel sheet Complete in all respect. |
| 351 | Providing & fixing of WET GRINDERSpecification1.Cap.15ltrs (1.0HP) 2.Stainless steel sheet constd. Complete in all respect. |
| 352 | Providing & fixing of DOUGH KNEADING MACHINESpecification1.(CROMPTON MOTOR 2.0 HP)2.App. Cap of Bowl 25Ltrs. 3.Motor with control switch. Complete in all respect. |
| 353 | Providing & fixing of POTATO PEELERSpecification 1.Cap.15Kg./chrgs. 2.(CROMPTON MOTOR 1.0 HP)3.Top of the drum will have a potato inlet door |
| 354 | Providing & fixing of PULVERISER(Std.)Specification1.(CROMPTON MOTOR 1.0 HP)2.Stainless steel sheet body,20g thick3.The unit will be fitted with 1.0 hp single Phase electric. Complete in all respect. |
| 355 | Providing & fixing of WORKTABLESUPPORTOF PULVERISORSpecification1.Size 1500X600X850mm2.Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sounddeadning material lining as required. Complete in all respect. |
| 356 | Providing & fixing of WORK TABLE WITH SINK for vegetable washing Specification1.Size 1950x600x850+1502.Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion.3. Sink bowl size 450x450x250mm Complete in all respect. |
| 357 | Providing & fixing of CHOPPING BOARD for manual vegetable cutting Specification1.Size 1200X600X850mm2.Frame work made of s.s.anlge top will have P.P./Nylon Board for chopping 700x700x100mm chopping board. Complete in all respect. |
| 358 | Providing & fixing of VEGETABLE CUTTING MACHINESpecification1.Aluminium casted body with ½ hp electric motor safety switch & double feed pusher for round flat & vertical shaped food items etc.,2. Provided with 4 no cutting discs for slicing grating Dicing.Complete in all respect. |
| 359 | Providing & fixing of CHAPPATI COLLECTION TABLESpecification1.Size 1500X600X8002. Top tray of 16G s.s.sheet, tray will have App Complete in all respect. |
| 360 | Providing & fixing of CHAPPATI ROLLING TABLESpecification1.Size 2100x650x850mm2. Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Complete in all respect. |
| 361 | Providing & fixing of CHAPPATI PLATE CUM PUFFERSpecification1.Size 1800x650x850mmmm2. Frame work of m.s.anlge, mounted on s.s.tubular legs frame work Complete in all respect. |
| 362 | Providing & fixing of EXHAUST HOOD(Without Ducting Fixing & Extraction fan) for chapatti plateSpecification1.Size 1950x750x600mm2.Made of s.steel sheet, 20G thick duly welded & pop 5anitar as required Complete in all respect. |
| 363 | Providing & fixing of FOOD TROLLEY WITH 4 ROUND PANS1RICETRAY &STORAGE beneath Specification1.O/S 1350X750X900mm2.S.S.Sheet insulated body3. Frame work of m.s.anlge of size 38x38x5mm Complete in all respect. |
| 364 | Providing & fixing of Hand wash Unit- Splash as per Layout (Rear & against side wall) Front & free side marine edge. 350mm dia.x200mm High Die Pressed Sink complete with 38mm dia. C.P. Drain Waste Out let. 16 gauge S.S-304 wall brackets. Complete in all respect. |
| 365 | Providing & fixing of TRAY CARRIER TROLLEYSpecification1.Size 1200X600X1200mm2. S.S.Bottom base shelf mount at 150mm with all four sides turned down 50mm in 12mm and secured to welded s.s.anlge frame work & PROVIDED WITH THREE NOS. OF DETACHABLE TRAYS CUM SHELFS UNIT WILL BE MOUNTED ON 4” PILLAR TYPE CASTORS WHEELS (2 NOS. WITH BRAKE & 2 NOS. WITHOUT BRAKE). Complete in all respect. |
| 366 | Providing & fixing of TRAY SET UP COUNTER WITH BAIN MARIE & DOUBLE OVER SHELVESSpecification1.Size 1800x600x850+375+2252. Top of 16G s.s.sheet,3.Bain Marie water tank of 18G s.s.sheet Complete in all respect. |
| 367 | Providing & fixing of STORAGE CABINETSpecification1.Size 1200X600X850mm2. Top of 16Swg S.S.Sheet one over shelf, three sides of 20 SWG s.s. sheet. Dish storage cabinet with 2 shelves and sliding door will be provided on service side. Complete in all respect. |
| 368 | Providing & fixing of STORAGE RACKSpecification1.Size 900X450X18002. Vertical of 32 mm dia stainless steel pipe with adjustable feet 4 no of 18 S.S Sheet at equally distance. Complete in all respect. |
| 369 | Providing & fixing of INGREDIENT BINSSpecification1.Size 600X600X600mm2. Made of S.S. 18 SWG WITH TOP HINGE OPENABLE DOORS SUPPORT WITH FOUR NOS. OF CASTORS, anti crack body, top half hinged lid. Provided with a scoop Complete in all respect. |
| 370 | Providing & fixing of DUNNAGE RACKSpecification1.Size 1200X600X500mm2. Made of s.s.square pipes of size 32x32mm, with support of 25mm square s.s.pipe. Complete in all respect. |
| 371 | Providing & fixing of POTRACK-3 TIERSpecification1.Size 1200X600X1500mm2. Verticals of 32mmX32mm square s.s.pipe, 3 shelves welded with vertical frame of 19mm dia s.s.pipe shelves with equal space between two tubes mounted on adjustable feet Complete in all respect. |
| 372 | Providing & fixing of SOILED DISH LANDING TABLE WITH GARBAGE CHUTESpecification1.Size 2400x600x850mm2. Top of 16G s.s.sheet with ‘Sunkun’ top |
| 373 | Providing & fixing of THREE SINK UNITSpecification1.Size 1800x600x850+150mm2. Top & 3 sink bowls of 16G s.s.sheet.3. Each Sink Bowl Size 500x500x300mm (without 6anitary fittings). Complete in all respect. |
| 374 | Providing & fixing of CLEAN DISH TABLESpecification1.Size 2100x600x850mm2. Specification same as that of work table but with 2 undershelves. Complete in all respect. |
| 375 | Providing & fixing of CLEAN DISH RACKSpecification1.Size 900x450x1800mm2. Vertical of 32 mm dia stainless steel pipe with adjustable feet 5 no vertical at equal distance 1st shelf fixed at 150mm from floor level. Complete in all respect. |
| 376 | Providing & fixing of L.P.GGAS PIPELINE(IN FEET)Specification1.ACTUAL MEASUREMENT WILL BE ACCORDING TO As persite conditions Complete in all respect. |
| 377 | Providing & fixing of LPG MENIFOLD SYSTEM 3X3CYLENDER Complete in all respect. |
| 378 | Providing & fixing of CENTRIFUGAL EXHAUST BLOWERSpecification1. 20000 CFM Complete in all respect. |
| 379 | Providing & fixing of S.S GRATING for kitchen drainage trough Specification1. (APPROX 25 RUNNING FEET)2. ACTUAL MEASUREMENT WILL BE ACCORDING TO As per site conditions Complete in all respect. |
| 380 | Providing & fixing of EXHAUST HOOD DUCTINGSpecification1.ACTUAL MEASUREMENT WILL BE ACCORDING TO As persite conditions |
| 381 | Providing & fixing of Chapati Making Machine:* Capacity: 900/1000 chapati per hour* Diameter - 4 to 7 inch* Thickness - 1-2 mm* Weight - 500 Kg approx* LPG Consumption - 2.5 kg per hour Complete in all respect. |
| 382 | Providing & fixing of IDLY STEAMER Doubled walled mineral wool insulated all SS sheet body on tiny tubular legs with adjustable bullet feet. Fitted with two nos immersion type heating element of 3.0 KW each with individual auto temperature controller and indicating lamps and SS hinges inside to keep detachable idly trays. Also fitted with water inlet, outlet valves and water level indicator. A front opening insulated door is fitted at the service side.120 Idlys. Complete in all respect. |
| 383 | Providing & fixing of SANDWICHGRILLER(DOUBLE) A commercial double sandwich griller is a high-capacity electric appliance, commonly featuring stainless steel construction, dual non-stick cast iron grilling plates (approx. and 3.6kW–5kW power. Designed for high-volume, it holds 4–8 sandwiches, operates on 220-240V, and features adjustable temperature controls up to for quick, consistent, double-sided grilling |
| 384 | Providing & fixing of WATER COOLER of capacity 200Ltr, and having Emerson compressor unit, condensing coil, light indicator, 75mm Puff insulation. Heavy-duty adjustable legs at the bottom. Totally body outside & inside made of 20 Swg SS Sheet. Sheet to be sheared with shearing machine and bended over CNC machine etc. Complete in all respect. |
| 385 | Providing & fixing of WEIGHING SCALECapacity 500 kg accuracy 50 gm, pan size 600x600mm, Weighing balance specifications define the accuracy, capacity, and performance of instruments used for precise mass measurement. Key parameters include readability for analytical), capacity high repeatability and rapid stabilization times, typically requiring automatic internal calibration, drafted shields, and RS-232/USB interface Complete in all respect. |
| 386 | Providing & fixing of INSECT KILLER UNITS of size 24” TUBE etc, complete as required as per technical specifications enclosedInsect killer units (fly catchers/zappers) commonly feature dual UV-A tubes each) to attract pests and a high-voltage metal grid to electrocute them, or a sticky board for hygienic trapping. They are designed for wall/ceiling mounting, Complete in all respect. |
| 387 | Providing & fixing of Air Curtain focus on maintaining a high-velocity air barrier to prevent dust, insects, and air leakage. Key specs include air velocity (typically 10-25 m/s), air volume (CFM), motor power, noise level (50-70 dB), installation height, and casing material (stainless steel or aluminum). Units usually operate on 230V/1Ph/50Hz, featuring centrifugal or propeller fans.Complete in all respect. |
| 388 | Providing & fixing of HOOD TYPE DISH WASHER with drying zone customer benefit features i.e. control lamps for service management, detergents and water treatment winter halter - one button operation, clearly displaying, the operational status of the machine intelligent zone activation, flexible installation options, 3 Fold hygiene filter system i/c media mat cyclone, ware wash water purifier, compact size of only 1300 mm, and providing detergent pump and dosing pump of suitable capacity. Complete in all respect. |
| 389 | Providing & fixing of Dining Table with Chair Standard dining table sets typically feature a 28–30 inch high table, with seats 17–19 inches from the floor, designed to provide 24 inches of space per person. Common rectangular 6-seater sets measure roughly 60–72 inches long and 36–40 inches wide, usually made from durable hardwood, marble, or glass, featuring upholstered or wooden chairs Complete in all respect. |
| 390 | Kitchen Equipment at Transit Site |
| 391 | Providing & fixing of MILKBOILER/TEABOILER Specification 1. Cap.50Ltrs. 2.S.S.Sheet insulated body with triple jacket 3.The water jacket will be fitted with 2 Kw heating element Complete in all respect. |
| 392 | Providing & fixing of MICROWAVE OVEN SpecificationMicrowave oven specifications typically include a 20-32 liter capacity, 700-1200W output power, and 230-240V, 50Hz input voltage. Common types are Solo (reheat/defrost), Grill (browning/crisping), and Convection (baking/roasting). Key features include stainless steel or ceramic interiors, child safety locks, auto-cook menus, and digital touch controls |
| 393 | Providing & fixing of PICKUP COUNTER WITH OVER SHELFSpecification1. Size 1800X600X850+3002.Top 3 sides, under & over shelf of s.s.sheet, on m.s.angle & s.s.tubular legs frame work.3. The counter will have 3 sides fully covered, operator side open Complete in all respect. |
| 394 | Providing & fixing of WORK TABLE FOR SUPPORT OF TWO BURNER RANGESpecification1. Size 1350x600x850mm.2. Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining Complete in all respect. |
| 395 | Providing & fixing of TWO BURNER COOKING RANGESpecification. App. Size 1200X600X850mm or features heavy-duty stainless steel (SS 202/304) construction, high-pressure/low-pressure LPG burners, and individual controls with pilot lights. Typical specifications include a splash-back, cast iron pan supports, undershelves, and dimensions around 48\\"–60\\" length, 24\\"–30\\" width, and 34\\"–36\\" working height Complete in all respect. |
| 396 | Providing & fixing of EXHAUST HOOD (Without Ducting Fixing & Extraction fan)FOR TWO BURNER RANGESpecification1. Size 1950x750x600mm 2. Made of s.steel sheet, 20G thick duly welded & pop 2anitar as requiredComplete in all respect. |
| 397 | JUICER (table top model) Specification1. Cast Aluminum/CI body, duly polished / painted, with worm & perforated insert. Top feedingtray. Worm easily cleanable fitted with 1/2HP elect. motor. Complete in all respect. |
| 398 | Providing & fixing of CONVEYOR TOASTERSpecification1.App. Cap. 100-125 Toasts/hr.2.S.S.Sheet body, having s.s.sheet conveyor belt. App.225mm wide. The unit will have heating elements on top & lower portion of conveyor belt with variable heat &speed control switch. Complete in all respect. |
| 399 | Providing & fixing of WORK TABLE WITH SINKSpecification1.Size 1950x600x850+1502. Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion. Complete in all respect. |
| 400 | Providing & fixing of FOUR DOOR REFRIGERATORSpecification1.Size 1950x600x850+1502. Double walled, insulated ‘PUF’ body made of 0.8mm thick s.s.sheet3. The unit will have 4 doors with magnatic rubber gascuts & locking provision Complete in all respect. |
| 401 | Providing & fixing of WORK TABLESpecification1.Size 1500X600X850mm2. Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Complete in all respect. |
| 402 | Providing & fixing of THREE BURNER COOKING RANGESpecification1.SIZE 1800X600X8502. Structure made of m.s. angle of size 38x38x5mm,duly rust proof painted.3. Top of 16Swg thick s.s.sheet Complete in all respect. |
| 403 | Providing & fixing of Chapati Making Machine:* Capacity: 900/1000 chapati per hour* Diameter - 4 to 7 inch* Thickness - 1-2 mm* Weight - 500 Kg approx* LPG Consumption - 2.5 kg per hour Complete in all respect. |
| 404 | Providing & fixing of LOW HT.TABLE 3anitary3rting low height burner Specification1.Size 750x750x600mm2. Specification same as that of work table but the table will be without undershelf & will have cross bracing support at lower portion. Complete in all respect. |
| 405 | Providing & fixing of LOWHT. BURNERSpecification1.Size 750x750x600mm2.Specification same as that of cooking range but the unit will be without undershelf, but will only have cross bracingsupport at lower portion. Complete in all respect. |
| 406 | Providing & fixing of EXHAUSTHOOD(With out Ducting Fixing & Extractionfan)for LOWHEIGHT BURNER range Specification1.Size 1650x750x600mm2.Made of s.steel sheet, 20G thick duly welded & pop 3anitar as required. The hood will be complete with s.s.sheet removable type baffle filters. Complete with greese collection channel & greese collection cup/s. |
| 407 | Providing & fixing of THREE BURNER COOKING RANGESpecification1. O/S 1800X600X8502.Structure made of m.s. angle of size 38x38x5mm, duly rust proof painted3. Top of 16Swg thick s.s.sheet Complete in all respect. |
| 408 | Providing & fixing of WORK TABLE FOR SUPPORT OF 03 BURNER COOKINGRANGESpecification1.Size 1500X600X850mm2.Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sound deadning material lining as required. Complete in all respect. |
| 409 | Providing & fixing of EXHAUSTHOOD(With out Ducting Fixing &Extractionfan)for THREE BURNER RANGESpecification1. Size 1950x750x600mm2.Made of s.steel sheet, 20G thick duly welded & pop 3anitar as required. Complete in all respect. |
| 410 | Providing & fixing of BULKCOOKER/boiler TILTING TYPESpecification. A Tilting Type Bulk Cooker/Boiler is a high-capacity commercial cooking unit, typically made of 304-grade stainless steel with a 160–200+ liter capacity. It features a, manual or geared tilting mechanism, heavy-duty LPG burners or electric induction heatingComplete in all respect. |
| 411 | Providing & fixing of BULK FRYER TILTING TYPE Cap.100Ltrs.Specification1.Cap.100Ltrs2.Triple jacketed body of stainless steel sheet Complete in all respect. |
| 412 | Providing & fixing of EXHAUST HOOD (Without Ducting Fixing & Extraction fan)for BULK COOKER & FRYER Size 1650x750x600mm Specification1.Size 1650x750x600mm 2.Made of s.steel sheet Complete in all respect. |
| 413 | Providing & fixing of WET GRINDERSpecification1.Cap.15ltrs (1.0HP) 2.Stainless steel sheet constd. Complete in all respect. |
| 414 | Providing & fixing of DOUGH KNEADING MACHINESpecification1.(CROMPTON MOTOR 2.0 HP)2.App. Cap of Bowl 25Ltrs. 3.Motor with control switch. Complete in all respect. |
| 415 | Providing & fixing of POTATO PEELERSpecification 1.Cap.15Kg./chrgs. 2.(CROMPTON MOTOR 1.0 HP)3.Top of the drum will have a potato inlet door |
| 416 | Providing & fixing of PULVERISER(Std.)Specification1.(CROMPTON MOTOR 1.0 HP)2.Stainless steel sheet body,20g thick3.The unit will be fitted with 1.0 hp single Phase electric. Complete in all respect. |
| 417 | Providing & fixing of WORKTABLESUPPORTOF PULVERISORSpecification1.Size 1500X600X850mm2.Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Top to have sounddeadning material lining as required. Complete in all respect. |
| 418 | Providing & fixing of WORK TABLE WITH SINK for vegetable washing Specification1.Size 1950x600x850+1502.Top & Sink bowl of s.s.sheet, on s.s.anlge & s.s.tubular frame work with cross bracing at lower portion.3. Sink bowl size 450x450x250mm Complete in all respect. |
| 419 | Providing & fixing of CHOPPING BOARD for manual vegetable cutting Specification1.Size 1200X600X850mm2.Frame work made of s.s.anlge top will have P.P./Nylon Board for chopping 700x700x100mm chopping board. Complete in all respect. |
| 420 | Providing & fixing of VEGETABLE CUTTING MACHINESpecification1.Aluminium casted body with ½ hp electric motor safety switch & double feed pusher for round flat & vertical shaped food items etc.,2. Provided with 4 no cutting discs for slicing grating Dicing.Complete in all respect. |
| 421 | Providing & fixing of CHAPPATI COLLECTION TABLESpecification1.Size 1500X600X8002. Top tray of 16G s.s.sheet, tray will have App Complete in all respect. |
| 422 | Providing & fixing of CHAPPATI ROLLING TABLESpecification1.Size 2100x650x850mm2. Top & undershelf of s.s.sheet on m.s.anlge frame work & s.s.tubular legs, with adjustable feet. Complete in all respect. |
| 423 | Providing & fixing of CHAPPATI PLATE CUM PUFFERSpecification1.Size 1800x650x850mmmm2. Frame work of m.s.anlge, mounted on s.s.tubular legs frame work |
| 424 | Providing & fixing of EXHAUST HOOD(Without Ducting Fixing & Extraction fan) for chapatti plateSpecification1.Size 1950x750x600mm2.Made of s.steel sheet, 20G thick duly welded & pop 5anitar as required Complete in all respect. |
| 425 | Providing & fixing of FOOD TROLLEY WITH 4 ROUND PANS1RICETRAY &STORAGE beneath Specification1.O/S 1350X750X900mm2.S.S.Sheet insulated body3. Frame work of m.s.anlge of size 38x38x5mm Complete in all respect. |
| 426 | Providing & fixing of TRAY CARRIER TROLLEYSpecification1.Size 1200X600X1200mm2. S.S.Bottom base shelf mount at 150mm with all four sides turned down 50mm in 12mm and secured to welded s.s.anlge frame work & PROVIDED WITH THREE NOS. OF DETACHABLE TRAYS CUM SHELFS UNIT WILL BE MOUNTED ON 4” PILLAR TYPE CASTORS WHEELS (2 NOS. WITH BRAKE & 2 NOS. WITHOUT BRAKE). Complete in all respect. |
| 427 | Providing & fixing of TRAY SET UP COUNTER WITH BAIN MARIE & DOUBLE OVER SHELVESSpecification1.Size 1800x600x850+375+2252. Top of 16G s.s.sheet,3.Bain Marie water tank of 18G s.s.sheet Complete in all respect. |
| 428 | Providing & fixing of STORAGE CABINETSpecification1.Size 1200X600X850mm2. Top of 16Swg S.S.Sheet one over shelf, three sides of 20 SWG s.s. sheet. Dish storage cabinet with 2 shelves and sliding door will be provided on service side. Complete in all respect. |
| 429 | Providing & fixing of STORAGE RACKSpecification1.Size 900X450X18002. Vertical of 32 mm dia stainless steel pipe with adjustable feet 4 no of 18 S.S Sheet at equally distance. Complete in all respect. |
| 430 | Providing & fixing of INGREDIENT BINSSpecification1.Size 600X600X600mm2. Made of S.S. 18 SWG WITH TOP HINGE OPENABLE DOORS SUPPORT WITH FOUR NOS. OF CASTORS, anti crack body, top half hinged lid. Provided with a scoop Complete in all respect. |
| 431 | Providing & fixing of DUNNAGE RACKSpecification1.Size 1200X600X500mm2. Made of s.s.square pipes of size 32x32mm, with support of 25mm square s.s.pipe. Complete in all respect. |
| 432 | Providing & fixing of POTRACK-3 TIERSpecification1.Size 1200X600X1500mm2. Verticals of 32mmX32mm square s.s.pipe, 3 shelves welded with vertical frame of 19mm dia s.s.pipe shelves with equal space between two tubes mounted on adjustable feet Complete in all respect. |
| 433 | Providing & fixing of SOILED DISH LANDING TABLE WITH GARBAGE CHUTESpecification1.Size 2400x600x850mm2. Top of 16G s.s.sheet with ‘Sunkun’ top |
| 434 | Providing & fixing of THREE SINK UNITSpecification1.Size 1800x600x850+150mm2. Top & 3 sink bowls of 16G s.s.sheet.3. Each Sink Bowl Size 500x500x300mm (without 6anitary fittings). Complete in all respect. |
| 435 | Providing & fixing of CLEAN DISH TABLESpecification1.Size 2100x600x850mm2. Specification same as that of work table but with 2 undershelves. Complete in all respect. |
| 436 | Providing & fixing of CLEAN DISH RACKSpecification1.Size 900x450x1800mm2. Vertical of 32 mm dia stainless steel pipe with adjustable feet 5 no vertical at equal distance 1st shelf fixed at 150mm from floor level. Complete in all respect. |
| 437 | Providing & fixing of L.P.GGAS PIPELINE(IN FEET)Specification1.ACTUAL MEASUREMENT WILL BE ACCORDING TO As persite conditions Complete in all respect. |
| 438 | Providing & fixing of LPG MENIFOLD SYSTEM 3X3CYLENDER Complete in all respect. |
| 439 | Providing & fixing of CENTRIFUGAL EXHAUST BLOWERSpecification1. 20000 CFM Complete in all respect. |
| 440 | Providing & fixing of S.S GRATING for kitchen drainage trough Specification1. (APPROX 25 RUNNING FEET)2. ACTUAL MEASUREMENT WILL BE ACCORDING TO As per site conditions Complete in all respect. |
| 441 | Providing & fixing of EXHAUST HOOD DUCTINGSpecification1.ACTUAL MEASUREMENT WILL BE ACCORDING TO As persite conditions |
| 442 | Providing & fixing of Hand wash Unit- Splash as per Layout (Rear & against side wall) Front & free side marine edge. 350mm dia.x200mm High Die Pressed Sink complete with 38mm dia. C.P. Drain Waste Out let. 16 gauge S.S-304 wall brackets. Complete in all respect. |
| 443 | Providing & fixing of WATER COOLER of capacity 200Ltr, and having Emerson compressor unit, condensing coil, light indicator, 75mm Puff insulation. Heavy-duty adjustable legs at the bottom. Totally body outside & inside made of 20 Swg SS Sheet. Sheet to be sheared with shearing machine and bended over CNC machine etc. Complete in all respect. |
| 444 | Providing & fixing of Dining Table with Chair Standard dining table sets typically feature a 28–30 inch high table, with seats 17–19 inches from the floor, designed to provide 24 inches of space per person. Common rectangular 6-seater sets measure roughly 60–72 inches long and 36–40 inches wide, usually made from durable hardwood, marble, or glass, featuring upholstered or wooden chairs Complete in all respect. |
| 445 | Providing & fixing of Air Curtain focus on maintaining a high-velocity air barrier to prevent dust, insects, and air leakage. Key specs include air velocity (typically 10-25 m/s), air volume (CFM), motor power, noise level (50-70 dB), installation height, and casing material (stainless steel or aluminum). Units usually operate on 230V/1Ph/50Hz, featuring centrifugal or propeller fans.Complete in all respect. |
| 446 | Furniture |
| 447 | TABLE FOR DINNING HALL MODEL:PERFORM SZIE:1800L X 900D X 750HPERFORM - METAL STRAIGHT LEGSTable top : made up of 18mm thick Hidroshield topUnderstructure: supported on MS powdercoated Straight leg with MS support beam |
| 448 | TABLE FOR MEDICAL ROMM/ SECURITY ROOM /ADMIN ROOM/ WARDEN MODEL:PERFORM SIZE:1500WX750DX750HT SIDE COMPOSITE STORAGE SIZE:900WX450DX750HT SpecificationsTable Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges Support: End Legs: MS powder coated legs Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht Wire Management: 65mm Dia Wire Manager Grommet/Flip up with cable dump SIDE COMPOSITE STORAGE Top & Sides : 18mm Thk pre laminated particle board Back : 9mm Thk pre laminated particle board Shutters : 18mm Thk pre laminated particle board Edge : All exposed area with 2mm thick PVC edge lipping Handle : Finger groove handle Lock : Regular lock |
| 449 | TABLE FOR MEETING ROOM MODEL:PERFORM SIZE:2400WX1200DX750HTSpecificationsTable Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges Support: End Legs: MS powder coated legs Intermediate Legs: MS podwer coated 60X40mm legs and supporting MS cross beams (40X20mm) Wire Management: 450mm Aluminium flipup with soft closure and provision to mount switches and sockets on Cable tray & Intermediate leg with wire entry / vertical wire entry cover considered. |
| 450 | DOUBLE BED FOR GUEST ROOM-1 /GUEST ROOM -2The head rest, foot rest & bed side panels are from 25mm thk, E1 grade, particle board prelaminated on two sides, with rounded corners. The storage - drawer units and center panels are of 18mm thk prelam particle board. Height of head rest panel is 750mm and of foot rest is 450mm. The inner structure of the cot has a metal tubular frame work, Tubes are confirming to IS 4923:1997, it is in- addition to center panels of prelaminated particle board. Cot comes with two movable storage units, each of size 980mm L x 750mm D x 275mm H, fixed with castor wheels for easy accessability and mobility. The storage units designed to accomodate on either side (left side or right side) of the cot depending upon the clients requirement. The storage facia comes with flush handle as a standard offering. The foot rest & head rest panels comes with adjustable levellers. Mattress base or platform is of 18mm thk prelam particle board in white laminate finish. The design offers a knockdown Construction, easy to assemble, strong and robust product. All metal parts comes with powder coating finish of 60-80 microns thick. All hardware are of steel, comes with zinc blue / yellow / black passivation. |
| 451 | 2-SEATER SOFA FOR GUEST ROOM-1 & 2 MODEL:CONVERSE2 Seater: 1375 (W) x 750 (D) X 820 (H)Seat Foam: the sofa is made up of fine quality leatherette.The structure is made up of silver wood and pine wood.The Seat is made of PU Foam with Density 32 to 40 +/- 2 kg/cu .mtr Seat is upholstered wuth Leatherite.Back Foam: The Back is made of PU Foam with Density 32 to 40 +/- 2 kg/cu, Backis upholstered with Leatherite.Unterstructure is made up of silver wood or pine wood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Legs should be made up of stainless steel tubes/pipes. |
| 452 | CHAIR FOR DINNING HALL MODEL:TANGChair is molded from GF 20% Polypropylene conforming to ASTM D 638 STD & Complying to ROHS. Seat & back design will be integrated as a single unit. The chair shall be injection molded with 2500 tonnage press. The chair should weigh about 3.9 kg. The back will be designed with triangular structural trusses & narrowed at the top to provide strength & comfort to the chair with good air circulation to the user. The back should be designed to provide ergonomic comfort with precise curvature to offer good lumbar support. The seat profile should be designed with water fall to provide necessary comfort in popliteal region. The design of the chair will be provided with four U shaped legs ensuring good strength to the chair. Chair shall be tested for minimum load bearing capacity of 150 KG. The design should have the capability to stack.Chair should be BIFMA and Green Guard certified. |
| 453 | CHAIR FOR CONFERENCE ROOM/ SECURITY ROOM MODEL:ASTRO MB* Astro Medium Back Mesh Chair* AC 60 Mesh* Single Lock Synchro Mechanism* Adjustable Lumbar Support* One Way Adjustable Arms (Height)* Nylon Base* Fabric Upholstered Cushion Seat |
| 454 | CHAIR FOR MEDICAL ROMM /ADMIN ROOM/ WARDEN MODEL:ASTRO HB* Astro High Back Mesh Chair* Headrest* AC 60 Mesh* Single Lock Synchro Mechanism* Adjustable Lumbar Support* One Way Adjustable Arms (Height)* Nylon Base* Fabric Upholstered Cushion Seat |
| 455 | VISITOR CHAIR FOR MEDICAL ROMM/ SECURITY ROOM /ADMIN ROOM/ WARDEN MODEL:ASTRO VISITOR* Astro Medium Back Mesh Visitor Chair* AC 60 Mesh* Adjustable Lumbar Support* Fixed Arms* Powder Coated Sledge Base* Fabric Upholstered Cushion Seat |
| 456 | SINGLE BED MODEL:COMFORTSZIE:2016L X 900D X 350 /800HThe inner-structure of the cot is a welded frame supported by vertical legs of 40x40x1.60 thk (16g) MS-ERW tubes confirming to IS 4923:1997. The metal structure is cladded with the wooden panels, ie., the head rest, foot rest & side panels are from both side laminated prelam particle board of 18mm thickness. Height of head rest is 800mm and foot rest is 425mm. The wooden panels are designed to cover the mattress by about 10mm from all four sides to avoid slip-off of the mattress, the inner area of the cot can also be used as a storage, since there will be ample space. The panels are at a height of 75mm from the ground. Legs come engineering polymer moulded leg bush & levellers for level adjustment. The mattress base is from 12mm thk plywood sheet. (The base can be also offered in prelam MDF or prelam particle board case to case basis, however the price will be varied accordingly) .The design offers a knockdown Construction, easy to assemble and a stable product. All metal parts comes with powder coating finish of 60-80 microns thick. All hardware are of steel, comes with zinc blue / yellow / black passivation. |
| 457 | BED SIDE TABLE SIZE:450L X 450D X510H BED SIDE STORAGEConfiguration - 1 Drawer on Top + Open shelf belowBody - made up of 18MM Thk Prelaminated Particle Board with 2 MM PVC Edge banding Drawer - With full panel drawer slides and Finger groove handle with cam Lock Finish - As per Approved Shade |
| 458 | STUDY TABLE MODEL:HOSTEL TABLEStudy tableSize : 800L x 525D X 750HtSpecification : Table top is 25mm thk PLB Understructure in Sq 25 tube with powder coating finish 200*800 Modesty |
| 459 | CHAIR FOR STUDY TABLE MODEL:GENIUS*Genius Stackable Chair*Powdercoated Legs*Can be ganged for straight line. Colour : Black & White |
| 460 | Center Table 1050x600x450Ht |
| 461 | SIGNAGE WORK |
| 462 | Providing and fixing External Signage's made of SS 304 (brush finish) 1mm thk.sheet for Logo and letters with raising(letter depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated/hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl of 7 years warrenty for desired colour with OSRAM make LEDS and IP 67 Grade OSRAM powersupply with 5 years warrenty fixed on the wall with necessary fixtures. |
| 463 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge Stair direction at landing |
| 464 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge stair no. |
| 465 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge stair floor level Indicator |
| 466 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge Fire safety disclaimer |
| 467 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge fire hose cabinet |
| 468 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer inchargefire alarm |
| 469 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge fire extinguisher |
| 470 | FIRE EVACUATION PHOTOLUMINICENT SIGNAGES Emergency Signage :- Round Corner signages with radius 8 to 12 mm, made of 3mm ACP sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge fire exit |
| 471 | EMERGENCY EVACUATION PLAN Providing and fixing fire Evacuation Photolumicent Signage made of Sandwhich Acrylic frame work of 5 mm + 5mm thickness. Signages made of premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS Spacers 18 mm x 25 mm, as per directions of engineer incharge. Signages to be bilingual/trilingual language. BRAND/MAKE- 247SIGN/ ASB Neon/ Glo-Lite Evacuation plan |
| 472 | EMERGENCY BATTERY BACKUP SIGNAGES Providing Emergency Evacuation signage with battery backup made of following:- ITEM Name:-Edge Lit Emergency Signage MODEL - EMEX3726- Premium IS Code 10322 (part5/section-8) 2013 Casing:-Anodised Aluminium with Plastic / Metal Side Caps. Signages Over all size :-375 x 260 mm Text Panel:- 8 mm Acrylic Back Up Duration :- 180 Minutes Primary Power Source:- AC - 220-240 Volt Luminarre:- LED Battery Disconection Fuse Battery Capacity:- 2600 MAH Battery Type:- Lithium ION AC to DC Built in Fuse Fuse for Circuit protection AC, Charging, EMERGENCY Indicators Emergency Test Switch Installation:- In client scope through certified electrical contractor. MAKE- 247 sign/ Glo-Lite/ Prolite Battery Backup |
| 473 | GENERAL INSTRUCTION SIGNAGES Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. No Smoking |
| 474 | GENERAL INSTRUCTION SIGNAGES Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. No Littering |
| 475 | GENERAL INSTRUCTION SIGNAGES Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. Instructional Signages |
| 476 | AREA IDENTIFICATION SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.3mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Room Identification/ Room Name |
| 477 | AREA IDENTIFICATION SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.3mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Room No. |
| 478 | AREA IDENTIFICATION SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.3mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Washroom Mounted |
| 479 | AREA IDENTIFICATION SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.3mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Lift No. |
| 480 | AREA IDENTIFICATION SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.3mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Lift Lobby |
| 481 | AREA IDENTIFICATION SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.3mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Floor Level Lift |
| 482 | AREA IDENTICATION WAYFINDER SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front inside. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. This is double sided signages having twim plates. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Washroom wall projected sign |
| 483 | AREA IDENTICATION WAYFINDER SIGNAGES Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with champagne/ brown/ silver finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front inside. Fixing arrangment made of anodised aluminium in champagne/ brown/ silver shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2.5 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. This is double sided signages having twim plates. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Ceiling hung |
| 484 | Basement Parking ceiling hung Signage made of double sided ACP (4MM +4MM) thk. with 90* edges. Print on 3M clear vinyl on retroreflective sheet of 3M/Avery make with 12mm aluminium powdercoat beading on all sideds with gloss lamination for extra durability with chain ceiling hung arrangement Ceiling hung double sided |
| 485 | FOUNTAIN / WATER BODY WORK |
| 486 | Providing and fixing of fountain / water body including construction of fountain / water body as per design, specification as required complete in all respect as directed by engineer in charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender