Tender For Deposit Work (Ndf/2026/65) Restoration Of Rain Damages To Lwss Answai In G.P. Chaswal Tehsil Dhar Ur, Distt. Mandi (H.P.). (Sh:- Construction of Water Filtration Chamber & Protection Work To Civil Structures).
Tender Value
1.19 Lakhs
Estimated cost
Bid Submission
24 Aug 2026
1 days left
EMD
2400
Bank guarantee accepted
Document Fee
350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mandi → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Deposit Work (Ndf/2026/65) Restoration Of Rain Damages To Lwss Answai In G.P. Chaswal Tehsil Dhar Ur, Distt. Mandi (H.P.). (Sh:- Construction of Water Filtration Chamber & Protection Work To Civil Structures).
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundations, trenches etc. in earth work, lift upto 1.50 metres stacking the excavated soil not more than 3 metres clear from the edge of excavation and then returning the stacked soil in 15cm layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within a lead of 20 metres. |
| 2 | Providing and laying cement concrete 1:3:6 (1 Cement : 3 Sand :6 graded stone aggregate 40 mm nominal size) and curing complete work excluding cost of form work in foundation and plinth as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 3 | Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in : |
| 4 | Foundation ,footing, basis of columns and the like mass concrete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 5 | Walls any thickness including attached pillaster buttresses plinth and string courses from top of foundation up to all floor level as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 6 | Suspended floor roofs, landing ,shelves and their supports balconies beams, girders, bressumers and cantilevers upto all floor level in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 7 | Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering strutting and propping etc. with wooden batten and ballies, in all heights of propping and centring below supporting floor to ceiling not exceeding 4 mtrs and removal of the same for insitu-reinforced concrete and plain concrete work in :- |
| 8 | Vertical surfaces such as wall (any thickness) partitions and the like including attached pillasters, buttresses plinth and string courses and the like in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-charge. |
| 9 | Flat surfaces such as soffits of suspended floors, roofs, landings and the like, floors etc upto 200 mm in thickness with in all leads and lifts as per direction of Engineer-in-Charge. |
| 10 | Providing and fixing Tor Steel reinforcement for RCC work including in position including cost of binding wire upto all floor level as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 11 | Providing and placing in horizontal layers filtering media duly graded, screened, washed and cleaned as specified by the Engineer-in-Charge. |
| 12 | Bottom layer: Broken stone screened, washed and graded from 50mm to 75mm from approved source |
| 13 | Middle layer (6-20mm). |
| 14 | Top layer: Course sand). |
| 15 | Providing and fixing of 3.15mm MS Sheet Manhole cover 600X600mm fixed on all sides with ISA 40x25x5mm top angle iron frame hinged on ISA 35x35x5mm bottom angle iron frame as per drawing. Pieces of MS Flat 20x4mm, 0.15m long be fixed on all sides as hold fast. The operation of manufacturing shall including cutting of MS Sheet, Angle Section & welding of MS Sheets, Angle Section, Hinges, Handles 150mm long, 20x4mm flats, locking arrangement and applying a priming coat of steel primer after pretreatment of surface to the entire satisfaction of the Engineer-in-Charge. |
| 16 | Providing and fixing copper alloy End wheel valve of various dia screwed type as per ISI-778. Marked complete in all respect as per direction and to the entire satisfactioln of Engineer-in-Charge. |
| 17 | 32 mm dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender