Tender For Construction Of Gymnasium Hall In College C Us, Pggc, Sector 46, Chandigarh. (Composite Work)
Tender Value
7.81 Crore
Estimated cost
Bid Submission
28 Aug 2026
5 days left
EMD
15.63 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Gymnasium Hall In College C Us, Pggc, Sector 46, Chandigarh. (Composite Work)
BOQ
| Sl. No. | Item Description |
| 1 | Civil Work (Part-A) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and for all lift, as directed by Engineer-in-Charge DSR 2.6 |
| 3 | All kinds of soil DSR 2.6.1 |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m DSR 2.8 |
| 5 | All kinds of soil. DSR 2.8.1 |
| 6 | Supplying and filling in plinth with local fine sand under floors, including watering, ramming, consolidating and dressing complete. DSR 2.27 |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : DSR 4.1 |
| 8 | 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.8 |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : DSR 4.1 |
| 10 | 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) DSR 4.1.10 |
| 11 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. DSR 4.17 |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for all heights:DSR 5.9 |
| 13 | Foundations, footings, bases of columns, etc. for mass concrete DSR 5.9.1 |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 15 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. DSR 5.9.2 |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 17 | Suspended floors, roofs, landings, balconies and access platform DSR 5.9.3 |
| 18 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 19 | Shelves (Cast in situ) DSR 5.9.4 |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 21 | Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR 5.9.5 |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 23 | Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6 |
| 24 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 25 | Stairs, (excluding landings) except spiral-staircases DSR 5.9.7 |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 27 | Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards DSR 5.9.13 |
| 28 | Centering and shuttering including strutting, propping etc. and removal of form for all heights:DSR 5.9 |
| 29 | Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like DSR 5.9.15 |
| 30 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: DSR 5.9 |
| 31 | Edges of slabs and breaks in floors and walls DSR 5.9.16 |
| 32 | Under 20 cm wide DSR 5.9.16.1 |
| 33 | Extra for additional height in centring, shuttering wherever required with adequate bracing, proping etc., i/c cost of de-shuttering and de-centring at all levels, over a height of 3.5 mtr. , for every additional height of one meter or part there of (plan area to be measured) for suspended floors, roofs, landing, beams,gutters suspended floors, roofs, landing, beams, gutters and balconies etc. (plan area to be measured). DSR 5.11.1 |
| 34 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. DSR 5.22 |
| 35 | Thermo-Mechanically Treated bars of grade Fe- 500D or more DSR 5.22.6 |
| 36 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. DSR 5.22A |
| 37 | Thermo-Mechanically Treated bars of grade Fe 500 D or more DSR 5.22A.6 |
| 38 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. DSR 5.33 |
| 39 | All works upto plinth level DSR 5.33.1 |
| 40 | Concrete of M30 grade with minimum cement content of 350 kg /cum DSR 5.33.1.2 |
| 41 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.DSR 5.33 |
| 42 | All works above plinth level upto floor V level DSR 5.33.2 |
| 43 | Concrete of M30 grade with minimum cement content of 350 kg /cum DSR 5.33.2.2 |
| 44 | Add for using extra cement in the items of design mix over and above the specified cement content therein. DSR 5.35 |
| 45 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: DSR 6.1 |
| 46 | Cement mortar 1:4(1 cement :4 coarse sand) DSR 6.1.1 |
| 47 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : DSR 6.4 |
| 48 | Cement mortar 1:4(1 cement :4 coarse sand) DSR 6.4.1 |
| 49 | Extra for forming cavity 5 cm to 11.5 cm wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M .S. ties 300 mm long of 25x3mm section at not less than 3 ties per sqm as per approved design. DSR 6.6 |
| 50 | Extra for providing & placing in position 2 Nos., 6mm dia. M.S. bars at every third course of half brick masonry. DSR 6.15 |
| 51 | Providing and fixing GRC Cladding Tiles of size 230mmx75mmx10mm confirming to IS:1237 in approved design, size, texture, thickness, pattern and colour on wall cladding up to all height including necessary scaffoldings. The composition of tiles should be '43' grade White Portland cement, reinforced in Alkali Resistant Glass Fibre and the pigment should be done with exterior grade synthetic inorganic iron oxide pigment. The pigmentation should be homogenous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated water proofing agents and other. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water abortion of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The tiles should be fixed with the cement mortar 1:3 (1 cement:3 coarse sand) and mixed with water proofing compound installation to be done by specialized vendor in strict supervision complete in all respect to the entire satisfaction of Engineer-in-charge. NS |
| 52 | Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4(1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. DSR 6.38 |
| 53 | Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level DSR 6.45 |
| 54 | Cement mortar 1 : 4 (1 cement : 4 coarse sand) DSR 6.45.2 |
| 55 | Providing and laying autoclaved aerated concrete (AAC) blocks masonry with 150mm to 300 mm thick with Grade 1 AAC Blocks of density 551 to 650 Kg/Cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved blcok laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seprately). DSR 6.47 |
| 56 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : DSR 11.23 |
| 57 | Raj Nagar plain DSR 11.23.2 |
| 58 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. DSR 8.2 |
| 59 | Granite of any colour and shade DSR 8.2.2 |
| 60 | Area of slab over 0.50 sqm DSR 8.2.2.2 |
| 61 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work DSR 8.3.2 |
| 62 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. DSR 8.5 |
| 63 | Providing and laying 1st quality ceramic glazed wall tiles of size 300x600 mm conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make, in all colours, shades as approved by Engineer-in-Charge,in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand). The tiles are to be fixed by provding 2 mm thick spacer. The area of spacer is to be filled by using cement based grout of approved shade. The grooves are to be filled with cemenitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material complete in all respect and to entire statisfaction of Engineer-in-Charge. NS |
| 64 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. DSR 9.20 |
| 65 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws DSR 9.20.1 |
| 66 | Providing and fixing wooden moulded beading to door and window frames with iron screws,plug and priming coat on unexposed surface etc. complete: DSR 9.40 |
| 67 | 2nd class teak wood 50x12mm DSR 9.40.1.1 |
| 68 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. DSR 9.83 |
| 69 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete : DSR 9.96 |
| 70 | 300x16 mm each 257.15 DSR 9.96.1 |
| 71 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :DSR 9.97 |
| 72 | 250x10 mm DSR 9.97.2 |
| 73 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. DSR 9.101 |
| 74 | Twin rubber stopper DSR 9.101.2 |
| 75 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. DSR 10.16 |
| 76 | Hot finished welded type tubes DSR 10.16.1 |
| 77 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. DSR 10.27 |
| 78 | 10 x 140 mm DSR 10.27.4 |
| 79 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels,plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). DSR 10.28 |
| 80 | Extra for marble/ granite stone flooring in treads of steps and risers using single length up to 2.00 metre. DSR 11.25 |
| 81 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1 : 4 (1cement : 4 coarse sand) : DSR 11.26 |
| 82 | 25 mm thick DSR 11.26.1 |
| 83 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. DSR 11.27 |
| 84 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : DSR 11.55 |
| 85 | Flamed finish granite stone slab Jet Black, Cherry Red,Elite Brown, Cat Eye or equivalent. DSR 55.1 |
| 86 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. DSR 12.22 |
| 87 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. DSR 12.41 |
| 88 | 110 mm diameter DSR 12.41.2 |
| 89 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. DSR 12.42 |
| 90 | Coupler DSR 12.42.1 |
| 91 | 110 mm DSR 12.42.1.2 |
| 92 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. DSR 12.42 |
| 93 | Bend 87.5° DSR 12.42.5 |
| 94 | 110 mm bend DSR 12.42.5.2 |
| 95 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. DSR 12.42 |
| 96 | Shoe (Plain) DSR 12.42.6 |
| 97 | 110 mm Shoe DSR 12.42.6.2 |
| 98 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. DSR 12.43 |
| 99 | 110 mm DSR 12.43.2 |
| 100 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : DSR 12.45 |
| 101 | 12.5 mm thick tapered edge gypsum moisture resistant board DSR 12.45.3 |
| 102 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. DSR 12.5 |
| 103 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Gutter (600 mm over all girth) DSR 12.51.6 |
| 104 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. DSR 12.52 |
| 105 | GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. DSR 12.52.1 |
| 106 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. DSR 12.52 |
| 107 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard,manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardantPVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back sidemetalized polyester film so as to make the tile a completely sealed unit. DSR 12.52.3 |
| 108 | Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. DSR 12.55 |
| 109 | 12 mm cement plaster of mix : DSR 13.4 |
| 110 | 1:4 (1 cement: 4 coarse sand) DSR 13.4.1 |
| 111 | 15 mm cement plaster of mix : DSR 13.5 |
| 112 | 1:4(1 cement: 4 coarse sand) DSR 13.5.1 |
| 113 | 6 mm cement plaster of mix : DSR 13.16 |
| 114 | 1:3 (1 cement : 3 fine sand) DSR 13.16.1 |
| 115 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. DSR 13.82 |
| 116 | Two coats DSR 13.82.2 |
| 117 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : DSR 13.62 |
| 118 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture DSR 13.62.1 |
| 119 | Providing and applying white cement based putty of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80 |
| 120 | Applying priming coat: DSR 13.50 |
| 121 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works DSR 13.50.3 |
| 122 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. DSR 13.85 |
| 123 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre DSR 13.85.3 |
| 124 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass /stainless steel screws, all complete as per architectural drawings and the stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : DSR 21.1 |
| 125 | For fixed portion DSR 21.1.1 |
| 126 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) DSR 21.1.1.1 |
| 127 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass /stainless steel screws, all complete as per architectural drawings and the stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : DSR 21.1 |
| 128 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) DSR 21.1.2 |
| 129 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) DSR 21.1.2.1 |
| 130 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. DSR 21.2 |
| 131 | Pre-laminated particle board with decorative lamination on both sides DSR 21.2.2 |
| 132 | Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete,complying to ASTM C920, DIN 18540-F & ISO 11600 DSR 21.19 |
| 133 | Upto 10 mm depth and 10 mm width DSR 21.19.2 |
| 134 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. DSR 22.7 |
| 135 | d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.All above operations to be done in order and as directed and specified by the Engineer-in-Charge : DSR 22.7 |
| 136 | With average thickness of 120 mm and minimum thickness at khurra as 65 mm. DSR 22.7.1 |
| 137 | Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size between cavity wall, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed as per ASTM D 1621, density of 34-36 kg/m³ as per ASTM D 1622, water absorptions ? 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge. DSR 26.7 |
| 138 | Providing and fixing over head wooden storage cabinets 2'-0\\" high x 1'-0'' deep consisting of 19mm thick commercial board ISI marked (as per sketch) having 1 No. shelf with 6mm thick commercial ply on back side. The exposed surface of the cabinets shall be provided with 1mm thick limate of approved shade and inner surface shall be provided with 0.70mm thick limate . The exposed edges of the board shall be provided with 20mm x 6mm second class teak wood lipping including polishing. The rate further include the cost of piano type hinges, S.S handles 4\\"size, aluminium hasp & staple, magnatic catcher, fevicol, nails, screws complete fixed in position over wall with the help of dash fasterners complete in all respect to the entire satisfaction of the Engineer-in-charge. (Front elevation area be measured for payment.) NS |
| 139 | Providing and fixing wooden storage cabinet under work top 2'-0\\" high & 2'-0'' deep consisting of 19mm thick commercial board ISI marked with 6mm thick commmercial ply on back side including 1 Nos. Horizontal shelf ( as per sketch) . The front side of the cabinet shall be provided with 1mm thick laminate of approved shade and inner surface shall be provided with 0.70mm thick laminate including 20mmx 6mm thick second class teak wood lipping on exposed edges of the board. The rate further include the cost of piano type hinges , S.S handles 4\\"size, aluminium hasp & staple, magnatic catcher, stainless steel adjusters / lifters, fevicol, nails , screws complete fixed in position tothe entire satisfaction in the Engineer-in-charge. ( Front elevation area shall be measured for payment). NS |
| 140 | Providing, laying, spreading and compacting granular sub base material 150mm thick compacted of natural sand, morrum, gravel crushed stone or combination thereof as per MORT&H specification confirming to clause 401 coarse graded grading – 3 as per table 400.1 of MORT&H specification (5th revision), including spreading on the prepared sub grade with the help of tractor with planner of adequate capacity maintaining the requited slope and grade during operation, rolling with road roller 8-10 tone with the grade and cross fall (camber) to be checked and any high spot or depressing which becomes apparent, corrected by removing or adding fresh material, including cost of tools and plants, carriage of material from stacks, templates, barrier, lighting arrangement at night, chowkidar and maintenance of diversion etc. complete in all respect as per MORT&H specifications, density of GSB as laid 2 gms/cc complete in all respect and to the entire satisfaction of Engineer in charge. NS |
| 141 | Providing and laying vitrified floor tiles of size 600 x 600 mm single charge (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade. The tiles are to be fixed with 3mm grove using spacers. The tiles are to be laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm The grove are to be filled with cementitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material. Single charge vitrified tile of size 600x600 mm NS |
| 142 | Providing & fixing of 6.5mm Sports Flooring (Wonder Floor, Responsive, Ebaco) coated with surface protection PUR finish having wear layer of 1mm total weight 4.3 kg/Sqm, Abrasion resistance-Group-T Slip Resistance-R-9, Resistance to Chemicals and sound Absorption is 24 db complete installation and welding chord welding of joints with adhesive complete in all respects and to the entire satisfaction of the Engineer in charge. NS |
| 143 | Providing and fixing 8mm thick wooden laminated floor class of use 31/23 having wear resistance level of AC-4 as per EN-13329 with a direct pressure laminate surface including profile, treated with aluminium side, flooring of approved colour and shade complete in all respects and to the entire satisfaction of the Engineer in charge. NS |
| 144 | Providing and fixing Aluminium American Handles ISI Marked anodised canodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade , with nuts 8 screws , with nuts 8 scrtews etc. complete. size 300mm x 20mm NS |
| 145 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 300x300 mm NS |
| 146 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with I without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for :(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3(ii) Sites with structure height more than 20m for all wind speeds DSR 9.147 |
| 147 | Casement cum fixed panel window having single casement panel at both ends & middle fixed panel with S.S 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. DSR 9.147.E4 |
| 148 | Using R4 series with frame (64 mm & above ) x (50 mm & above) & sash (64 mm & above) x (70 mm & above) & mullion (64 mm & above) x (70 mm & above). (Height above 1.8 metre; each openable shutter upto 0.8m width) DSR 9.147.E4.3 |
| 149 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds DSR 9.147 |
| 150 | Fixed window/ ventilator with mullion /transom. DSR 9.147.C2 |
| 151 | Using R4 series with frame (64 mm & above) x (50 mm & above) & mullion (64 mm & above) x (70 mm & above). (Height above 2.5 metre) DSR 9.147.C2.4 |
| 152 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with I without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for :(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3(ii) Sites with structure height more than 20m for all wind speeds DSR 9.147 |
| 153 | Casement door double panel with French (False) Mullion with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides. DSR 9.147.F2 |
| 154 | Using R4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above) x (100 mm & above) & French (False) mullion (64 mm & above) x (60 mm & above). (Height above 2.5 metre). DSR 9.147.F2.2 |
| 155 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds DSR 9.147 |
| 156 | Casement door single panel with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.DSR 9.147.F1 |
| 157 | Using R4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above) x (100 mm & above). (Height above 2.5 metre). DSR 9.147.F1.2 |
| 158 | Providing and fixing 6mm thick plain glass panes over fixed portion or glazed shutter including the cost of hard wood beading including the cost of nails, putty etc. complete in all respect to the entire satisfaction of Engineer-in-charge.NS |
| 159 | Public Health (Part-B) |
| 160 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (DSR Item No.2.8) |
| 161 | All kinds of soil. (DSR Item No.2.8.1) |
| 162 | Excavating trenches by mechanical/ manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :(DSR Item No.2.10) |
| 163 | All kinds of soil. (DSR Item No.2.10.1) |
| 164 | Pipes, cables etc, not exceeding 80 mm dia.(DSR Item No.2.10.1.1) |
| 165 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia .(DSR Item No.2.10.1.2) |
| 166 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(DSR Item No.4.1) |
| 167 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). (DSR Item No.4.1.3) |
| 168 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources).(DSR Item No.4.1.10) |
| 169 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). (DSR Item No.5.3) |
| 170 | Centering and shuttering including strutting, propping etc. and removal of form for :(DSR Item No.5.9) |
| 171 | Suspended floors, roofs, landings, balconies and access platform.(DSR Item No.5.9.3) |
| 172 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.(DSR Item No.5.22) |
| 173 | Thermo-Mechanically Treated bars of grade Fe-500D or more.(DSR Item No.5.22.6) |
| 174 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:(DSR Item No.6.1) |
| 175 | Cement mortar 1:6 (1 cement : 6 coarse sand).(DSR Item No.6.1.2) |
| 176 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :(DSR Item No.6.4) |
| 177 | Cement mortar 1:6 (1 cement : 6 coarse sand). (DSR Item No.6.4.2) |
| 178 | 12 mm cement plaster finished with a floating coat of neat cement of mix :(DSR Item No.13.7) |
| 179 | 1:4 (1 cement: 4 fine sand). (DSR Item No.13.7.2) |
| 180 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(DSR Item No.17.7A) |
| 181 | (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer. (DSR Item No.) |
| 182 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (DSR Item No.17.16A) |
| 183 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.(DSR Item No.17.22B) |
| 184 | (a) 15 mm nominal dia. (DSR Item No.) |
| 185 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.(DSR Item No.17.28) |
| 186 | Flexible pipe. (DSR Item No.17.28.2) |
| 187 | 32 mm dia. (DSR Item No.17.28.2.1) |
| 188 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.(DSR Item No.17.33) |
| 189 | Providing and fixing toilet paper holder :(DSR Item No.17.34) |
| 190 | C.P. brass. (DSR Item No.17.34.1) |
| 191 | Providing and fixing soil, waste and vent pipes :(DSR Item No.17.35) |
| 192 | 100 mm dia. (DSR Item No.17.35.1) |
| 193 | Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. (DSR Item No.17.35.1.2) |
| 194 | 75 mm diameter : (DSR Item No.17.35.2) |
| 195 | Centrifugally cast (spun) iron socketed pipe as per IS: 3989. (DSR Item No.17.35.2.2) |
| 196 | Providing and fixing heel rest sanitary bend. (DSR Item No.17.40) |
| 197 | 100 mm dia. (DSR Item No.17.40.1) |
| 198 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.40.1.2) |
| 199 | 75 mm dia. (DSR Item No.17.40.2) |
| 200 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.40.2.2) |
| 201 | Providing and fixing single equal plain junction of required degree :(DSR Item No.17.44) |
| 202 | 100x100x100 mm. (DSR Item No.17.44.1) |
| 203 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.44.1.2) |
| 204 | 75x75x75 mm.(DSR Item No.17.44.2) |
| 205 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.44.2.2) |
| 206 | Providing and fixing door piece, insertion rubber washer 3 mm thick, bolts & nuts complete :(DSR Item No.17.55) |
| 207 | 100 mm. (DSR Item No.17.55.1) |
| 208 | Sand cast iron S&S as per IS - 3989. (DSR Item No17.55.1.2.) |
| 209 | 75 mm. (DSR Item No.17.55.2) |
| 210 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.55.2.2) |
| 211 | Providing and fixing terminal guard : (DSR Item No.17.56) |
| 212 | 100 mm. (DSR Item No.17.56.1) |
| 213 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.56.1.2) |
| 214 | 75 mm. (DSR Item No.17.56.2) |
| 215 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.56.2.2) |
| 216 | Providing and fixing collar: (DSR Item No.17.57) |
| 217 | 100 mm. (DSR Item No.17.57.1) |
| 218 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.57.1.2) |
| 219 | 75 mm. (DSR Item No.17.57.2) |
| 220 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.57.2.2) |
| 221 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :(DSR Item No.17.58) |
| 222 | 100 mm. (DSR Item No.17.58.1) |
| 223 | 75 mm.(DSR Item No.17.58.2) |
| 224 | Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :(DSR Item No.17.59) |
| 225 | 100 mm .(DSR Item No.17.59.1) |
| 226 | 75 mm .(DSR Item No.17.59.2) |
| 227 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :(DSR Item No.17.60) |
| 228 | 100 mm inlet and 75 mm outlet.(DSR Item No.17.60.2) |
| 229 | Sand cast iron S&S as per IS - 3989. (DSR Item No.17.60.2.1) |
| 230 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.(DSR Item No.17.81) |
| 231 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.(DSR Item No.18.10) |
| 232 | Internal work - Exposed on wall |
| 233 | 15 mm dia nominal bore.(DSR Item No.18.10.1) |
| 234 | 20 mm dia nominal bore.(DSR Item No.18.10.2) |
| 235 | 25 mm dia nominal bore.(DSR Item No.18.10.3) |
| 236 | 32 mm dia nominal bore.(DSR Item No.18.10.4) |
| 237 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :(DSR Item No.18.17) |
| 238 | 25 mm nominal bore.(DSR Item No.18.17.1) |
| 239 | 20 mm nominal bore.(DSR Item No.18.171A) |
| 240 | 32 mm nominal bore.(DSR Item No.18.17.2) |
| 241 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :(DSR Item No.18.18) |
| 242 | 25 mm nominal bore.(DSR Item No.18.18.3) |
| 243 | Providing and fixing uplasticised PVC connection pipe with brass unions :(DSR Item No.18.21) |
| 244 | 45 cm length. (DSR Item No.18.21.2) |
| 245 | 15 mm nominal bore.(DSR Item No.18.21.2.1) |
| 246 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :(DSR Item No.18.38) |
| 247 | 15 mm diameter pipe.(DSR Item No.18.38.1) |
| 248 | 20 mm diameter pipe.(DSR Item No.18.38.2) |
| 249 | 25 mm diameter pipe.(DSR Item No.18.38.3) |
| 250 | 32 mm diameter pipe.(DSR Item No.18.38.4) |
| 251 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) .(DSR Item No.18.46) |
| 252 | 15 mm nominal bore. (DSR Item No.18.46.1) |
| 253 | 20 mm nominal bore .(DSR Item No.18.46.2) |
| 254 | 25 mm nominal bore .(DSR Item No.18.46.3) |
| 255 | 32 mm nominal bore .(DSR Item No.18.46.4) |
| 256 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (DSR Item No.18.48) |
| 257 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :(DSR Item No.18.49) |
| 258 | 15 mm nominal bore. (DSR Item No.18.49.1) |
| 259 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.(DSR Item No.18.51) |
| 260 | 15 mm nominal bore. (DSR Item No.18.51.1) |
| 261 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. (DSR Item No.18.53) |
| 262 | 15mm nominal bore. (DSR Item No.18.53.1) |
| 263 | Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge.(DSR Item No.18.53.A) |
| 264 | Cutting holes up to 30x30 cm in walls including making good the same:(DSR Item No.18.76) |
| 265 | With common burnt clay F.P.S. (non modular) bricks. (DSR Item No.18.76.1) |
| 266 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.(DSR Item No.18.77) |
| 267 | Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.(DSR Item No.18.78) |
| 268 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :(DSR Item No.19.1) |
| 269 | 200 mm diameter. (DSR Item No.19.1.3) |
| 270 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :(DSR Item No.19.2) |
| 271 | 200 mm diameter S.W. pipe.(DSR Item No.19.2.3) |
| 272 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality.(DSR Item No.19.19) |
| 273 | H D - 20.(DSR Item No.19.19.3) |
| 274 | Circular shape 560 mm internal diameter.(DSR Item No.19.19.3.1) |
| 275 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:(DSR Item No.19.4) |
| 276 | 100x100 mm size P type.(DSR Item No.19.4.1) |
| 277 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.(DSR Item No.19.4.1.1) |
| 278 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:(DSR Item No.19.30) |
| 279 | Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets :(DSR Item No.19.30.3) |
| 280 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.(DSR Item No.19.30.3.1) |
| 281 | Providing and Fixing of C.P. Brass Towel Rail 600mm long of approved make complete in all respect at site. (As decided by the EIC) |
| 282 | Providing and fixing C.P. Brass Towel Ring of approved make complete in all respect. (As decided by the EIC) |
| 283 | Providing and fixing of C.P. brass Soap dish of approved make complete in all respects. (As desired by EIC) |
| 284 | Providing and Fixing of Chinaware oval shape counter wash basin with C.I. brackets without pillar taps, 32mm CP brass waste of standard pattren ,including painting of fittings and brackets cutting and making good the walls whereever require make as approved by EIC. |
| 285 | Providing and Fixing of C.P. Brass Revolving Joint Shower of approved make complete in all respect as per entire satisfaction of EIC. |
| 286 | Providing and Fixing of Grab Rail of 32 mm dia grade 304 stainless steel 600 mm long for handicape to toilet including stainless steel clamp and cost of cutting building and grouting in C.C. 1:2:4 complete in all respect. |
| 287 | Providing and Fixing of Urinal Partition Curved/ Rectangular Shaped with frosted/ toughed glass of 8 mm thick in Chrome finish approved make complete in all respect. (As decided by the EIC) |
| 288 | Providing and Fixing white vitreous china flat back half stall urinal of size 420x395x635mm with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS:2556, C.I. trap with outlet grating and other couplingts in C.P. brass, including painting of fittings and cutting and making good the walls and floors whereever required: (As decided by the EIC) |
| 289 | Providing and fixing of C.P. brass Autocloset pressmatic urinal cock of approved make Jcomplete in all respect at site. (As desired by EIC) |
| 290 | Supplying Installing Testing and Commissioning of Water Cooler with full stainless steel body Grade SS and 380 to 400 Ltr Storage capacity and cooling capacity 170-225 ltr/hr with Hermmetically sealed reciprocating/ rotary compressor complete in all respect. (BIS Approval IS 1475) |
| 291 | Supplying and Fixing of High speed Water Purifier with 3 stage purification system consisting of sediment filter, activated carbon filter and Ultravoilet treatment having purification capacity of 200 LPH, Water Control Sensor for automatic control of purifier as per level of water cooler and valve for back flushing of sediment filter complete in all respect. Make: Aquaguard, Kent, Usha, Brita, Pure-it, A-Pure etc. to the entire satisfaction of EIC. |
| 292 | Providing and Fixing of Voltage Stablizer (For Water Cooler) Copper Winding Range 160-280 Volt with timer MCB, Volt Meter, Amp Meter & 22 G Powder Coated Body complete in all respects to the entire satisfaction of EIC Make. V-Guard, Deol, Microtech, Luminous or any other make as per approved make list attached |
| 293 | 4 KVA |
| 294 | Providing and Fixing of angle iron stand for Water Cooler of the angle of size 50 x 50 x 5 including cutting, welding, primer and synthetic enamel painting two coats of required color after one coat of primer complete in all respect. |
| 295 | Providing and Fixing of 25 Ltr Capacity Hot Water Geyser including fixing at site of approved make complete in all respect. (As decided by the EIC) |
| 296 | Providing and fixing of 600x450 or 550x400 mm beveled edge mirror of superior glass (of approved quality) complete with 5 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (Based on DSR Item No.17.31) |
| 297 | Electrical Installation (Part-C) |
| 298 | A.) SCHEDULE NO.1 (ELECTRICAL INSTALLATION)DSR item No. 1.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mmFRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. |
| 299 | Group C |
| 300 | DSR Item No.1.4 Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc .as required. |
| 301 | DSR Item No.1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. |
| 302 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 303 | DSR item No.1.17 Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 304 | 3 x 1.5 sq.mm |
| 305 | 3 x 2.5 sq.mm |
| 306 | DSR item No.1.20 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. |
| 307 | 25 mm |
| 308 | DSR item No. 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 309 | DSR item No.1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 310 | Telephone Socket outlet |
| 311 | DSR item No. 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 312 | DSR item No. 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 313 | 1 or 2 Module (75 mm x 75 mm) |
| 314 | DSR item No. 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 315 | DSR item No.1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 316 | DSR item No. 1.33 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 317 | DSR item No. 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 318 | DSR item No.2.2 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required. |
| 319 | 100 A,30KA,FPMCCB |
| 320 | 200 A,36KA,FPMCCB |
| 321 | 250 A,36KA,FPMCCB |
| 322 | 400 A,50KA,FPMCCB |
| 323 | DSR Item No. 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without (MCB/RCCB/Isolator) |
| 324 | 4 way (4 + 12), Double door |
| 325 | 6 way (4 + 18), Double door |
| 326 | DSR item No. 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 327 | Single pole |
| 328 | Double Pole |
| 329 | Triple pole and neutral |
| 330 | DSR item No. 2.24 Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. |
| 331 | For 4 way, Double door TPN MCBDB |
| 332 | DSR item No. 5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 333 | DSR item No. 5.4 Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (with charcoal/coke and salt) as required. |
| 334 | DSR item No. 5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 335 | DSR item No. 5.12 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 336 | DSR item No.8.1 LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt )(Please refer DNIT for complete specification of item no.22) |
| 337 | 22 watt |
| 338 | DSR item No. 8.7 LED Panel light 2x2 ft.(System lumen efficacy ≥120 <135 lm/Watt) (Recessed/ Surface type) (Please refer DNIT for complete specification of item no.23) |
| 339 | 36 watt |
| 340 | DSR item No. 8.9 LED Batten light (System lumen efficacy ≥105 <120 lm/Watt). (Please refer DNIT for complete specification of item no.24) |
| 341 | 24-26 watt |
| 342 | DSR item No.8.16 LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy ≥120 and <135 lm/Watt). (Please refer DNIT for complete specification of item no.25) |
| 343 | 150 watt |
| 344 | DSR item No.9.2 Brush Less Direct Current (BLDC) Fan without Remote (Please refer DNIT for complete specification of item no.26) |
| 345 | 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) |
| 346 | 1400mm, service value ≥ 6.0 CM/Min/Watt, air delivery 245 CM/Min (Minimum) |
| 347 | DSR item No. 11.1 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 348 | 4 X 10 sq. mm (25mm) |
| 349 | 3 ½ x 400 Sq mm ( 82mm) |
| 350 | DSR item No.15.15 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. |
| 351 | 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 352 | 120 mm dia (OD-120 mm & ID-103 mm nominal) |
| 353 | DSR item No.15.16 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 354 | 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 355 | 120 mm dia (OD-120 mm & ID-103 mm nominal) |
| 356 | DSR item No. 10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 357 | Supply & erection of Exhaust Fan (heavy duty motor with copper wound metallic body) following size complete with motor, metallic blades, double ball bearing with minimum power consumption, rigid frame with rubber mounting for silent operation, epoxy powder coating along with metallic louver to be installed in the existing opening including cost of making the hole to suit the size of above fan making good the damage, Carriage Charges connection, testing, commissioning etc. as required to complete the job to the entire satisfaction of Engineer-in-charge. |
| 358 | Size 12 inch (300mm) Sweep, 900 RPM Heavy Duty Exhaust fan (Single Phase) with louver of Havells (Turbo Force SP) / Orient (Industrial Heavy Duty)/ Usha (Turbo HDEF)/ Crompton (EXHD300-6-1)/ Bajaj (Supreme Plus) make only. |
| 359 | Supply and laying of XLPE insulated PVC sheathed Aluminum conductor armoured cable of 1.1 KV grade as per IS 7098 (Part-I) 1988 (amended up to date) of the following sizes to be laid in existing Trench/Ducts/Cable Tray/ RCC/ HUME/ METAL/ DWC pipe / on surface with the help of MS clamps of suitable size/ as required at site to the entire satisfaction of Engineer-in-Charge. The job includes labour charges of laying the cable and making connections with suitable size aluminum lugs/thimbles etc. The cable shall be of Polycab / Havells / R.R. Kabel/ KEI/ Finolex make only. |
| 360 | 10 sq.mm 4 core (in pipe) |
| 361 | 10 sq.mm 4 core (on surface) |
| 362 | 400 sq.mm 3.5 core (in pipe) |
| 363 | Supply & fixing of OEM made Junction box IP-66/67 made out of Polycarbonate with Glass fiber reinforced of size 210x155x90 (minimum) with 5 nos. OEM made connectors/ terminal blocks. The Jn. Box and connectors/ terminal blocks should be supplied by OEM. The terminal blocks/ connectors should be of Hensel/ Wago/ Elmax/ Siemens make only and junction box shall be of Hensel make KF-1616 G or its equivalent Clipsal/ Legrand/ Rittal/ Schneider/ ABB make only. The Junction box shall be fire retardant and self-extinguishing. The gasket material shall be polyurethane and the gasket shall be internally embedded. The job includes the cost of cable glands for cable entry, mounting kit for pipe and post installation, fixing screw, all labour and petty material required to complete the job to the entire satisfaction of the Engineer in Charge of work. |
| 364 | Supply and erection of MS bracket F type suitable size and suitable shape made form 40mm x 40mm x 5mm thick angle iron to be installed on exiting parapet/ wall with help of suitable size of nuts and bolts etc. for erection of existing LED flood light fittings. The job also includes the cost of painting of box with superior quality of paint and other petty material etc as per required to complete the job. |
| 365 | Supply and erection of 14 GMS sheet frame of suitable size for erection of 12”/15”/18” sweep exhaust fan. The holder should be suitable for 12”/15”/18” sweep exhaust fan shall be cut from the centre of the sheet and bedding ¼” round collar with round cut and duly fixed with existing ventilator frame with suitable arrangement after removing the existing glass. The exhaust fan frame shall be painted on both side with superior quality paint after one coat of primer. The job includes the cost of M.S. strips of 1”x1/4” and other petty material required to complete the job to the entire satisfaction of Engineer-in-charge. |
| 366 | Supply fabrication & erection of M.S. angle iron board covered with 14 GMS sheet fixed in to the nitch for mounting switchgear. The board shall be fabricated out of 40mm x 40mm x 5mm angle iron frame and shall be covered with a 14 GMS sheet duly welded for erection of switchgear on it. The switches /BDB’s / ELCB shall be provided with required no. of supporting member of M.S. flat 25mm x 5mm to bring all the switchgear in one level including bonding the board switchgear etc. to the existing earth. The board shall be painted with two coat of approved shade of superior quality paint after one coat of primer. The rate includes carriage from factory to site, erection charges in the niche and other petty material required at site of work. |
| 367 | Supply & erection MCB 4 pole 63 Amp 415 Volt 10KA Breaking Capacity ‘C’ curve without enclosure. The job includes the labour charges and other petty material required to complete the job. The MCB should be of Lauritz Knudsen (Exora)/ Legrand (DX3)/ Hager (h3)/ Schneider (Acti9)/ ABB (SB200M)/ Siemens (Betagard) make only. |
| 368 | LED Panel light 1x4 ft. (System lumen efficacy ≥120 <135 lm/Watt) (Recessed/ Surface type) (Please refer DNIT for complete specification of item no.38) |
| 369 | 33 Watt./ 36 Watt. |
| 370 | Supply & erection of Wall Fan 400mm sweep oscillating type complete with blades with regulator. The fan should be of Havells (Swing)/ Usha (MAXX AIR)/ Orient (400mm Wall44)/ Crompton (WM Hiflo wave Plus)/ Bajaj (Esteem Double String) make only. The wall fan should be provided with double string i.e. one no. controlling oscillating and one for speed. The cost including connection with adjacent light points. |
| 371 | Labour charges for horizontal boring 1 Mtr. Below ground level for laying of DWC pipe including cost of 2 Nos. pit digging and refilling complete in all respects to entire satisfaction of the Engineer in Charge of the work. |
| 372 | Supply and fixing of 12 modules (200 mm x 150 mm) G.I box suitable for accommodate the following accessories along with modular base and cover plate for modular switches in recess/ surface etc as required for Computer Point with 4 Nos. 5/6 Amp. modular switch and 4 Nos. 3 pin 5/6 Amp. modular socket outlet. The job includes the cost of making interconnections with suitable copper wire, painting of box with approved paint and other petty material required to complete the job to the entire satisfaction of Engineer-in-Charge at site. The Modular accessories should be of Lauritz Knudsen (Entice) / ABB (Ivie) / Legrand (Myrius) / Crabtree (Athena)/ Norisys (Square series) make only. |
| 373 | S/E of LED Bulk Head Luminaries weather proof frosted light with PMMA / PC reflector and silicon gasket to be installed on surface. The LED fitting should have minimum system Lumen output minimum 1000 Lumen and the driver of the fitting should be workable on 140-260 Volt. The colour temperature of LED should be minimum 5000 degree Kelvin. The LED Bulk Head fitting should be of Philips /Wipro /Bajaj / Havells /Crompton / Jaquar/ Surya/ Lighting Technologies/ Trilux/ Panasonic make only. The fitting should be of IP-65/66. The LED should have a life of 50000 burning Hours. The fitting should have THD<15% and power factor 0.9 or above. The job includes the cost of testing, commissioning and making connection with copper wire from adjacent light point, other petty material and labour etc. as required to complete the same to the entire satisfaction of Engineer in Charge. |
| 374 | Supply & erection of sheet metal distribution board of suitable size of required number of ways for mounting Miniature Circuit Breaker/ Isolators including connection & bonding to the existing earth etc. as required to the entire satisfaction of EIC. The DB should be of Lauritz Knudsen (Exora)/ Legrand (Ekinox3)/ Hager (Novello+)/ Schneider (Acti9)/ ABB (Elegance)/ Siemens (Betagard) make only. |
| 375 | Sheet metal SP & N Distribution board (dust protected) provided with din bar suitable for incorporating MCB’s/Isolator 4 way. |
| 376 | S/E of stainless steel enclosure for MCCB 3 pole/ 4 pole. The enclosure shall be erected on existing angle iron board with nut bolts/ screws etc. to complete the job to the entire satisfaction of Engineer-In-charge. The MCCB enclosure should be of Lauritz Knudsen/ Siemens/ Schneider/ Legrand/ ABB/Hager make only. |
| 377 | 100Amp./125 Amp./160 Amp. |
| 378 | 200Amp./250 Amp./ 400 Amp. |
| 379 | Supply and erection of sheet metal bus-bar chamber on existing surface with required No. of bus-bar strips of suitable length and cross-sectional area, made of copper strips of suitable length and cross-sectional area enclosure made of M.S. sheet 1.6mm thick with detachable cover fitted with dust excluding gasket and secured with sufficient No. of cadmium plated iron screws and of given overall dimensions and to be fixed with G.I. bolts and nuts/Rag bolts and nuts etc., complete with all accessories including connections with suitable size tin coated copper thimbles, bonding to the existing earth and painting etc. as desired by the Engineer-in-charge. |
| 380 | Sheet metal bus-bar chamber suitable for 400 Amp. 3’ long 415 Volts capacity with 4 copper strip Bus-bars each of length 900 mm & cross-sectional area (38.10mm x 6.35mm) enclosure having overall dimensions (980mm x 550mm x 200mm) nominal. |
| 381 | Sheet metal bus-bar chamber suitable for 100 Amp. 2’ long 415 Volts capacity with 4 copper strip Bus-bars each of length 600 mm & cross-sectional area (25.4mm x 3.17mm) enclosure having overall dimensions (680mm x 400mm x 150mm) nominal. |
| 382 | B.) SCHEDULE NO.2 (FIRE ALARM SYSTEM) DSR item No.1.17 Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 383 | 2 x 1.5 sq.mm |
| 384 | DSR item No.1.20 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. |
| 385 | DSR item No..28.2.1 Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. |
| 386 | Two Loop Panel. |
| 387 | DSR item No.28.2.14 Supplying, installation, testing & commissioning of addressable manual call point complete as required. |
| 388 | DSR item No.28.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. |
| 389 | DSR item No.28.2.17 Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. |
| 390 | DSR item No.28.2.19 Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. |
| 391 | DSR item No.28.3.3 Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required. |
| 392 | DSR Item No. 28.5.3 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. |
| 393 | Speaker cable Single pair, 2-core, 1.5 sqmm |
| 394 | DSR item No.39.23 Supply and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm CRCA Sheet, completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking, Minimum 2 cable entry/exit provision at Top and bottom with rubber protection, Front 5mm Toughened Glass with lock, wall mounting kit, Powder coated Color- RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc. complete as required. |
| 395 | 6U Rack |
| 396 | Supplying, Installation, Testing and Commissioning of tabletop gooseneck unidirectional condenser microphone having gooseneck length between 400 mm to 500 mm, suitable for speech and public address applications, operating on a voltage range of 12 V to 48 V DC with current consumption less than 8 mA, sensitivity of 0.7 dB SPL, total harmonic distortion less than 0.6% at maximum input level, equivalent input noise of 28 dB SPL(A) with signal-to-noise ratio of 66 dB(A) referenced to 1 Pa, frequency response from 100 Hz to 16 kHz, and output impedance of 200 ohms. The microphone shall be complete with desktop base, connection accessories, mounting hardware and all other necessary components required for proper operation. The item includes all labour, tools, tackles, testing and commissioning at site to the entire satisfaction of the Engineer-in-Charge. Make: Bosch / Sennheiser / Shure only. |
| 397 | Supplying, Installation, Testing and Commissioning of 480 Watt Power Amplifier suitable for Public Address/Voice Evacuation System, operating on 24 V DC battery supply with maximum ±10% voltage variation, having frequency response of 60 Hz to 15 kHz (+1 dB/-3 dB), total harmonic distortion less than 3% at rated output power at 1 kHz, balanced XLR input with input impedance of 20 kΩ and input sensitivity of 1 Volt (microphone input), and signal-to-noise ratio greater than 80 dB. The amplifier shall be provided with all necessary accessories and in-built protection against overload, short circuit and overheating, complete with mounting, interconnections, testing and commissioning at site to the entire satisfaction of the Engineer-in-Charge. The item includes all labour, tools, tackles and consumable materials required for proper installation and operation. Make: Bosch / Crown / Honeywell / Bose only. |
| 398 | Supply and installation of Red/ Green LED Laser etched emergency exit signage‘s double sided pendant type made out of powder coated MS housing and etched acrylic sheet indicator with reflective light source> 2W LED, Emergency Backup of minimum 4 hours, 6V 3.2 AH SMF/ SLA battery, SMPS Power supply suitable for operation on 230 AV 50 Hz AC supply as per the requirement at all prominent locations to guide the way out of the building to the building users in case of fire. The size of the letter should be sufficient for visibility of the people as per NBC-2016. The exit sign board should be of THORN/ PROLITE/ AUTO GLOW/ AUTOLITE/ GLOWLITE/ HONEYWELL make only. |
| 399 | Supply, installation, testing and commissioning of 2x10 watt wall/ceiling mounted industrial Double Beam emergency LED light with exit sign board. The fitting should have CRCA steel housing, 5700K color Temperature, 50000 burning hours, minimum emergency backup of 4 to 5 hours. The fitting should be fully automatic i.e. automatic on in case of normal supply failure and automatic off as power resumes. The battery should have inbuilt protection for over, under charge and short circuit protection. The job also includes the cost of testing commissioning and making connections with 3x1.5 copper conductor from adjacent light point, other petty material and labour etc. as required to complete the job to be entire satisfaction of Engineer-in-Charge. Make: Mr. Lite/ Agni/ Edvent only. |
| 400 | DSR item No.26.1 Online UPS - Input supply: Single Phase, Output Supply: Single Phase. (Please refer DNIT for complete specification of item no.15 of SCHEDULE NO.2 ) |
| 401 | 2 KVA Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender