Tender For Provision Of New Ration Store At Building No.231 (Lgs Section) At Vsn Nagpur
Tender Value
32.10 Lakhs
Estimated cost
Bid Submission
04 Sep 2026
11 days left
EMD
64500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nagpur → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of New Ration Store At Building No.231 (Lgs Section) At Vsn Nagpur
BOQ
| Sl. No. | Item Description |
| 1 | Demolition or brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins,arches,pillars, etc but excluding ashlar facings,dressed stonework and precast concrete articles in cement mortor in 1:4 complete all as specified and directed. |
| 2 | Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 3 | Excavating in trenches .n.exc 1.5m wide and n.exc 1.5m depth for foundation etc or for shafts,wells,cesspits,manholes ,pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 4 | Removing excavated material n exc 50 m and depositng where directed at a level n exc 1.5 m above the starting points complete all as specified and directed. |
| 5 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 6 | Material and labour for cement concrete in foundations, filling and mass concrete (PCC) Type D2 1:4:8 (40 mm graded aggregate) etc complete all as specified and directed. |
| 7 | Material and labour for, RCC in M-25 ( 20 mm graded aggregate) for foundation including rafts, footings, foundation beams;, plinth beams; bases for columns, etc, complete all as specified and directed. |
| 8 | Material and labour for, RCC in M-25 ( 20 mm graded aggregate) for Columns, pillars, piers, posts & struts etc complete all as specified and directed. |
| 9 | Material and labour for, RCC in M-25 (20 mm graded aggregate) for Beams, cantilevers, bresummers, lintels over 1.5 m span complete all as specified and directed. |
| 10 | Material and labour for, RCC in M-25 (20 mm graded aggregate) for chajjas complete all as specified and directed. |
| 11 | Material and labour for, RCC in M-25 (20 mm graded aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 12 | Material and labour for TMT bars 10 mm dia & over cut to length, bent to shape required including cranking bending spirally for hooping for column, hooking ends & binding with & including mild steel wire (not less than 0.9 mm dia) or securing with clips quality conforming complete all as specified and directed. |
| 13 | All as per item No 12 above but 5 mm dia over upto and including 10 mm dia TMT bar in stirrups, spacers and binders complete all as specified and directed. |
| 14 | Supply and fix framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 15 | Material and labour for flat form work to sides of rough finished surfaces of concrete foundations, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams: and similar work; vertical or to batter complete all as specified and directed. |
| 16 | Material and labour for form work to sides of rough finished surfaces of pillars posts, struts, piers, columns & stanchions square rectangular or polygonal fair finished surfaces in shape complete all as specified and directed. |
| 17 | Material and labour for flat form work to sides rough finished surfaces of and soffits of floors or roof beams, beam haunchings, girderrs, bressum-mers, lintels cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc complete all as specified and directed. |
| 18 | Material and labour for flat fair finished surfaces Form work to soffits of suspended slab such as roof slabs, floors slabs, landing & similar work not exceeding 200 mm thick (Horizontal or sloping) etc complete all as specified and directed. |
| 19 | Material and labour for formwork to edges of rough finished surfaces of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. |
| 20 | Material and labour for for old size Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed. |
| 21 | Material and labour for providing PCC 1:3:6, type C2 (using 40 mm graded aggregate), 75 mm thick, finishing cement concrete surfaces even and fair without using extra cement, as in plinth protection, path etc including necessary form work and provision of bituminous joints mixed with bitumen and sand at intervals not exc 3.00mtr complete all as specified and as directed. |
| 22 | Supply only integral waterproofing compound. |
| 23 | Material and labour for moorum/red bajri filling in floors or paving, laid in layers n exc 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and as directed. |
| 24 | Material and labour for, broken stone or boulder hardcore of guage n exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick , watered and rammed to a true surface etc complete all as specified and as directed. |
| 25 | Material and labour for Cement concrete type B-0, 1:2:4 (12.5 mm graded agg.) 40 mm thick as in floors complete all as specified and as directed. |
| 26 | Material and labour for Kota stone flooring 20-25mm thick over and including 20mm screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing all as specified and directed. |
| 27 | All as per item No 26 above but as in skirting on verticle surfaces of wall over screed bed 10mm thick in CM (1:4) for kota stone all as specified and directed. |
| 28 | Material and labour for rendering 15 mm thick in CM 1:4 with water proofing compound @ 3 % by weight of cement, finished even and smooth without using extra cement (WPC shall be measured and paid separately) complete all as specified and directed. |
| 29 | Material and labour for rendering 5 mm thick on fair faces of brick or concrete surfaces with in CM 1:3 on ceilling finished even and smooth complete all as specified and directed. |
| 30 | Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces with in CM 1:6 is to be finished even & smooth (without using extra cement) wall complete all as specified and directed. |
| 31 | Material & labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gMaterial and labour foritre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces at any height incuding necessary scaffolding complete all as specified and directed. |
| 32 | Material and labour for for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed. |
| 33 | Material and labour for preparation of new plastered walls apply distempering 2 or more coat with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface at any height incuding necessary scaffolding complete all as specified and directed.Note : Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. |
| 34 | Material and labour for aluminium framed windows any pattern, fixed/side hung/silding (two or three track) using powder coated alluminium sections, of approved make with or with out sash bars suitable for 4mm thick glazing including necessary jointed cleats, glazing complete all as specified and directed. |
| 35 | Supply and fixing IInd class HW plain solid, straight ,chowkats and frame, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 36 | Supply and fixing 30mm thick flush door shutter solid core construction with block board case and plywood face panels, commercial type on both sides make as approved by GE. |
| 37 | Supply and fixing mild steel flat iron hold fast including bolts conforming to Fe-290 Gde-E-165 all as specified and as directed. |
| 38 | Material and labour for providing plain cement concrete 1:3:6 type C1 using 20mm graded aggregates for fixing hold fast and making good to disturbed surfaces complete all as specified and directed. |
| 39 | Supply and fixing for floor door stopper of brass body and tounge with hard drawn steel spring with over all length of cover plate is 150mm complete all as specified and directed. |
| 40 | Supply and fixing butt hinge, medium weight ,cold rolled mild steel 100mm long complete all as specified and directed. |
| 41 | Supply and fixing floor door stopper of aluminium alloy body and tongue anodised with rubber shoe and fixed of size 150 mm complete all as specified and directed. |
| 42 | Supply and fixing aluminium anodised barred tower bolt of extruded section 200 mm long and fixed all as specified and as directed. |
| 43 | Supply and fixing extruded aluminium alloy handle fabricated type anodised 150 mm long complete all as specified and directed. |
| 44 | Material and labour for for preparing new surfaces of wood of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 45 | Material and labour for for preparing new steel surfaces of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 46 | Supply and fixing aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy 300 mm long and fixed complete all as specified and directed. |
| 47 | Material and labour for roof treatment on RCC roof slab complete as mentioned below, all as specified and as directed:-(i) Cleaning the concrete surfaces of RCC roof slab thoroughly with wire brushes, washed and dried. (ii) Checking the roof slab by flooding test with water till total elimination of leakage/seepage/ dampness all as specified in SSR Part-I (after ascertaining location of leakage/seepage/ dampness, carrying out treatment vide item No. 9 hereinafter of pressure grouting shall be operated at the required locations). (iii) Brushing surface with neat cement slurry at the rate of 3.00kg of cement per Sqm.(iv) Cleaning the plastered roof surfaces and applying a coat of bitumen primer @ 0.3 kg/sqm on top of dry surface.(v) Laying APP modified polymeric membrane 3mm thick with non woven polyester core laid and bonded to the sub-strata and over-laps shall be sealed/fused by flame \\"torch', application method |
| 48 | Material and labour for applying bitumen base aluminium paint at 0.2 kg/Sqm in two coats over APP modified polymer complete all as specified and directed. |
| 49 | Material and labour for rendering over roof slab 10 mm thick in CM 1:3 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement and finished surfaces fair and even all as specified and directed. Note: WPC shall be measured and paid separately. |
| 50 | Material and labour for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. |
| 51 | Material and labour for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface complete all as specified and directed. Note: Area of the sub structure in contact with backfill to be measured. |
| 52 | Material and labour for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed. |
| 53 | E/M PORTIONNote: Removal and Returning, filling in will be measured under BOQ item No 4 and 5 above respectively. |
| 54 | Material and labourfor point wiring (concealed) on walls and surface on ceiling complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including non metallic medium grade rigid PVC conduit medium grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface, with and including suitable ISI marked modular boxes ,inner and outer cover of suitable make and 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed.(a) One light point controlled by one switch |
| 55 | (b) One Wall fan/ceiling fan point controlled by one switch |
| 56 | (c) One exhaust fan point controlled by one switch. |
| 57 | (d) One switch socket outlet modular type 3 pin 6 amp on same board. |
| 58 | All as per item No 53 above but 1.5 sq mm cable size and 1.5 sq mm earth continuity wire for one 3 pin socket outlet, 6 amps on Independent board. |
| 59 | All as per item No 53 above but 2.5 sq mm cable size with 2.5 sq mm earth continuity wire for one 3 pin socket outlet, 16 Amps on independent board. |
| 60 | Note for Item No. 53 to 58 :- The disturbed surfaces of wall for concealing box/wiring shall be make good by applying cement plaster, putty and colour wash etc matching with the existing surfaces. (ii) The rate for point wiring shall be deemed to include the cost of making good. |
| 61 | Supply and fixing LED security light fitting 25 W made out of pressure die cast aluminium powder coated housing high impact resistant 4 mm thick toughened glass cover and matrix of power LEDs in built electronic driver up to 4 KV surge protection fitted with adjustable pole adopter to enable on site tilt angle setting and input power 25 W system lumens 85/W operating voltage 160-260 V of make : CG Cat Part No. LSTS-25-CDL-M :- Note :(i) Rates are deemed to be included for security ligh brackets made out of 25 mm / 20 mm dia GI medium grade tubing of suitable length and bend to shape including fixing MS flat iron clamps, bolts & nuts as per site requirement complete all as specified and as directed. |
| 62 | Supply and fixing new master led tube 4ft 20 W LED batten of high-quality materials and design, Extruded aluminum housing enhances safety, High quality PC Diffuser. Reliable and robust housing structure having nominal system lumen output of 2500 lumens and a minimum system efficacy of 125 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70.The luminaire should have a color temperature of 6500K and CRI>83. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The total power consumption should not exceed 20W (including driver) complete all as specified and as directed. Make : CG Cat Part No. CCS-100-20-65-HL2-DP-NWH or equivalent in Bajaj/ Wipro. |
| 63 | Supply and fixing 0-4 step, two module, modular type electronic regulator for ceiling fan 1200 mm sweep, 240 volts, 120 Watts humfree single pole, all as specified and as directed. Make : Legrand Cat No. 675977 or equivalent in Seimens/ Havells |
| 64 | Supply and fixing switch modular type, single pole one way 6 Amps, 240 volts Ac suitable for modular switch boxes without indicator, all as specified and as directed. Make : Legrand Cat No. 675501 or equivalent in Seimens/ Havells |
| 65 | Supply and fixing socket modular type single pole one way 6 Amps 3 pin 240 volts all as specified and as directed. Make : Legrand Cat No. 675551 or equivalent in Seimens/ Havells |
| 66 | Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminalswith ISI marked all as specified and as directed. |
| 67 | Supply and fixing socket modular type 16 Amps, 3 pin combine, 2 module,240 volts all as specified and as directed. Make : Legrand Cat No. 675555 or equivalent in Seimens, Anchor Roma |
| 68 | Supply & Fix switch modular type 16 Amps, one way with indicator, 1 module,240 volts all as specified and as directed. Make : Legrand Cat No. 675513 or equivalent in Seimens/ Havells |
| 69 | Supply and fixing sheet metal enclosures for SPN DB's with metal double door for incorporating MCBs,IP-43 , 12 way with 200 amps rated busbar, 240 volts, with 100 Amp copper Bus bar as per IS-8623 complete all as specified and as directed. Make : Legrand Cat No 507612 or equivalent in Seimens/ Havells |
| 70 | Supply and fixing MCB SPN, 40 to 63 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. complete all as specified and as directed.Make : Legrand Cat No. 408619 or equivalent in Seimens/ Havells |
| 71 | Supply and fixing MCB SP 6-32 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. Supply and fixing complete all as specified and as directed. |
| 72 | Supply and fixing energy saving ceiling fan 1200 mm sweep min air delivery 210 CFM with double ball bearing in opal white colour and BEE 5 star rated BLDC complete including provision of 3 core copper wire of size 1.5 sqmm , connected from ceiling rose to fan and marking MES No in black paint complete all as specified and as directed. |
| 73 | Supply & Fixing new exhaust fan heavy duty metal body 18\\" ( 450 mm) sweep 230 V, 50 Hz, complete with all accessories & connector etc internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified and directed. |
| 74 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 2 core complete all as specified and directed. |
| 75 | Material and labourfor High density polyethylene pipes (HDPE) DWC duct pipe of size 63 mm dia laid in trenches for passing of LT cable complete all as specified and directed. |
| 76 | Excavation in trenches in hard/dense soil not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of cables and getting out of excavated material complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender