Tender For Comprehensive B/R Repair/Replacement And Maintenance Of Otm Accommodation At Itarana Cantt Under Age B/R-I Alwar
Tender Value
25 Lakhs
Estimated cost
Bid Submission
04 Sep 2026
12 days left
EMD
50000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Alwar → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Comprehensive B/R Repair/Replacement And Maintenance Of Otm Accommodation At Itarana Cantt Under Age B/R-I Alwar
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified& directed by Engr-in-Charge. |
| 2 | Demolition of cement concrete (un-renforced) in ground floor and paving. exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as specified& directed by Engr-in-Charge. |
| 3 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified& directed by Engr-in-Charge. |
| 4 | Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified& directed by Engr-in-Charge. |
| 5 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified& directed by Engr-in-Charge. |
| 6 | Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises complete all as specified& directed by Engr-in-Charge. |
| 7 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion & making good disturbed ground embedded in Concrete, brick work, masonry, etc complete all as specified& directed by Engr-in-Charge. |
| 8 | Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store complete all as specified& directed by Engr-in-Charge. |
| 9 | Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame not exc 1.5 sq. m & removing to store complete all as specified& directed by Engr-in-Charge. |
| 10 | Taking down cement plaster any description on brick or stone any description complete all as specified& directed by Engr-in-Charge. |
| 11 | M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 12 | M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed. |
| 13 | M&L for 75 mm thick PCC(1:3:6) type C1 (using 20mm graded stone aggregate ) as in plinth protection finished fair and even complete all as specified & directed by Engr-in-Charge. |
| 14 | M&L for 25mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in floor complete all as specified & directed by Engr-in-Charge. |
| 15 | M&L non skid ceramic tiles 7 to 8mm thick(square/rectangular) colored tiles area of each tiles exc 0.06 sqm but n.exc. 0.11 sqm in floor set and jointed in neat cement slurry and pointed in white or coloure cement and over 15mm thick screed bed in CM 1:6 complete all as specified & directed by Engr-in-Charge. |
| 16 | M & L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured to match surface over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed by Engr-in-Charge. |
| 17 | M&L Vetrified Ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in vertical surfaces as dado/ skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified & directed by Engr-in-Charge. |
| 18 | M&L Glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendering in cm 1:4 complete all as specified & directed. |
| 19 | M&L For False Ceiling Complete With Armstrong/Armgy p-FB ceiling Tiles of Size 595x595x9mm thick (as approved by GE) fixed with and including galvanised iron Powder coated inverted 'Tee\\" or \\"L\\" section (Concealed GI frame Work) Suspended From Ceiling with provision of Galvanised wire 4mm dia and wall tapping screws including butterfly clips, hold down clips for fixing the board to frame complete all as per manufacturer's instructions complete all as directed and specified. |
| 20 | M&L for solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. |
| 21 | M&L 5mm thick PVC sheet fillet of width 35mm for wall panelling, including cutting, fitting and fixing to wall with all adhesive/fixing accessories wall to make PVC Frame complete all as specified & directed. |
| 22 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engr-in-Charge. |
| 23 | S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 24 | Dismantling of stone slabs or tiles of any description or thickness as in floors, pavings, aprons, pathway etc laid dry or laid dry and pointed complete all as specified & directed. |
| 25 | M & L for machine cut kota stone slab flooring 20-25 mm thick over cement slurry base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 15mm thick screed bed in CM 1:6, including rubbing and polishing complete all as specified and as directed |
| 26 | M & L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 27 | M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types over and including 20mm thick screed bed in CM 1:6 cement concrete complete all as specified and as directed . |
| 28 | M & L for 20 mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed and jointing with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 10mm thick rendering in CM 1:4 for recieving stone etc complete all as specified and as directed. |
| 29 | M&L for 15mm thick rendering on fair faces of brick work or stone masonry or concrete surfaces in CM 1:4 including finished surfaces even and smooth without using extra cement complete all as specified and directed. |
| 30 | M&L for 10mm thick rendering in CM 1:6 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement complete all as specified. |
| 31 | M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified. |
| 32 | M&L for preparation of newly plastered surfaces of wall and applying two coat of cement base paint over a coat of primer including cornices, pillasteres complete all as specified & as directed. |
| 33 | M&L for preparation of newly plastered surfaces of wall and applying two coats of Oil bound distemper over a coat of alkali resistant primer complete all as specified and directed. |
| 34 | M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified. |
| 35 | M&L for preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified. |
| 36 | M&L for preparation of old plastered or unplastered surface of wall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash complete all as specified and as directed. |
| 37 | Description all as per srl item No.36.00 here-in-above but on ceiling surfaces. |
| 38 | M & L for complete removing of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil greasy spots etc on old decorated surfaces of wall and applying two coats of oil bound distemper of approved shade/tint over and including a coat of primer over and including 1 mm thick Birla white wall care putty complete all as specified and as directed. |
| 39 | Demolition Mud/PCC in roofs padding any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed by Engr-in-Charge. |
| 40 | M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified& directed by Engr-in-Charge. |
| 41 | M&L Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m including cleaning surfaces over bituminious primer complete all as specified& directed by Engr-in-Charge. |
| 42 | M&L for APP based plymeric membrane minimum weighing 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non woven reinforcement/mat (center core) with thermal insulation laid by toarch application method with overlaps 100mm on length side and 100mm on the width side as per manufacture,s instructions with fabric (wt not less than 150 gms/sqm) on primed surface complete all as specified. |
| 43 | Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) all as specified & as directed. |
| 44 | M&L for RCC type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified & as directed. |
| 45 | M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 46 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 47 | M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed. |
| 48 | S&F for steel work in tubular section for post /truss/ purlin/rafters etc including special shaped washer etc. complete using induction butt welded tubes conforming to I.S. 1161-1998 grade St- 240 complete all as specified and directed. |
| 49 | M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. |
| 50 | S&F mild steel screw bolts (Machine made) with hexagonal or square heads at one end and the screwed the other to be fitted with washers and one hexagonal or square but exc 22.5 but n.exc 30 cm long, dia of neck/shank 11 to15 mm complete all as specified and directed. |
| 51 | M&L for providing plain cement concrete type B1, 1:2:4 (20 mm graed aggregate) as in copings complete all as directed. |
| 52 | M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) for Rough finished surfaces of concrete flat complete all as specified and as directed. |
| 53 | M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for Rough finished surfaces of concrete flat complete all as specified and as directed. |
| 54 | S & F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note:- The measurement shall be taken of front elevation and not girthwise. |
| 55 | Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed. |
| 56 | Taking up or down 20mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed. |
| 57 | S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed. |
| 58 | S&F steel tubing medium grade 20mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed. |
| 59 | S&F in repairs ball valves of 20mm dia, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed, minimum weight - 210 gms complete all as specified & directed. |
| 60 | S&F in repairs 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed. |
| 61 | S&F in repairs 25 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed. |
| 62 | S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia complete all as specified. |
| 63 | S&F in repair PVC connection of 15mm bore with 2 Nos PTMT nuts, 45cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe complete all as specified & directed. |
| 64 | S&F in repair Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified & directed. |
| 65 | S&F in repair fancy type 3-Hole Basin Mixer without popup waste system but including plain waste 32mm size with aerator complete cast copper alloy, chromium plated, screwed down high pressure, with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified & directed. |
| 66 | S&F in repair sink with draining board made out of stainless steel 1mm thick sheet for kitchen with plug, washers, waste pipe, cast iron centilever bracket, connecting union over all minimum size 915mmx460mm with bowl size 410mmx330mmx160mm complete all as specified and directed. |
| 67 | S&F in repair kitchen sink without draining board made out of stainless steel 1mm thick with plugs, washers and waste pipe including bedding in cement mortar to dwarf wall or including and fixing cast iron cantilever brackets and connecting union to pipe over all size 495x420 mm bowl size 410x330x160 mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as specified & directed. |
| 68 | S&F in repairs Stainless steel plate rack, 1.00mm thick for kitchen size 600x900x230mm complete all as specified & directed by Engr-in-Charge. |
| 69 | S&f in repairs 32mm dia waste fittings, brass CP for glazed ware sinks, basin etc with long screwed shanks and fly nuts, flange and based in red lead cement and other and fixed all as specified. |
| 70 | Demolition and breaking up drain pipes (Salt glazed ware, AC, PVC or Reinforced concrete) set in cement mortar of size 110mm/ 75 mm dia complete all as specified & directed. |
| 71 | S&F in repair PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified & directed. |
| 72 | S&Fin repair PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified & directed. |
| 73 | S&F in repair PVC (SWR) bends any radius 110 mm bore complete all as specified & directed. |
| 74 | S&F in repair PVC (SWR) vent cowl 110mm complete all as specified & directed |
| 75 | S&F in repair 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed |
| 76 | S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed |
| 77 | S&F in repair PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed. |
| 78 | S&F 35mm thick IInd class hard wood factory made panelled door shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified & directed. |
| 79 | S&F 35 mm thick IInd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed. |
| 80 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified & directed. |
| 81 | S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified& directed. |
| 82 | S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed |
| 83 | S&F Butt hinges 100mm long medium weight, colled rolled mild steel complete all as specified & directed. |
| 84 | S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed. |
| 85 | S&F 150mm Aluminium handles, cast type, anodised complete all as specified & directed. |
| 86 | M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified& directed. |
| 87 | S & F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed. |
| 88 | S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed. |
| 89 | S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed. |
| 90 | S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed. |
| 91 | M&L for preleminated particle board, interior grade, prelaminated both sides with decorative choise lamination fixed with screws complete all as specified and directed. |
| 92 | S&F for powder coated of any colour as approved anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed. |
| 93 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 94 | S&F sheet glass ordinary quality,in squares n. exc. 0.5 SQM each 4.80 mm thick complete as directed |
| 95 | S&F factory made steel windows with side hung shutters including projecting type box hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded including one shop coat of Zinc chromate primer. |
| 96 | Description all as per item No 95 here-in-before but without glazing bars. |
| 97 | S&F steel ventilator with top hung shutter including hinges steel peg stay complete including taking down. |
| 98 | S&F 4mm thick ordinary sheet glass fixed with clips and putty completed in squares not exc 0.50 Sqm each pane all as specified and as directed. |
| 99 | Hacking out old broken glass of any thickness/size & any description from wooden or steel frame fixed with clips/putty/wooden beading and S&F with 3mm thick ordinary sheet glass fixed with clips and oil putty/wooden beading completed in squares not exc 0.50 Sqm each pane all as specified and as directed. |
| 100 | Description all as per item No 99 here-in-before but 3mm thick figured glass, pin head type. |
| 101 | Hacking out old broken glass from metal/aluminium frame incl punching or drilling out old glazing pins/springs/clips/ beading and providing & fixing new of any thickness/size of any description and S&F for 5.5 mm thick Sheet glass, ordinary quality and glazing in square exc 0.5 sq. m in each pane complete all as specified. |
| 102 | S&F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed tinned tacks or GI wire stampe or nails and screws/wooden beading complete all as specified & directed. |
| 103 | S&F in repairs SS Curtain rod 19/20mm dia as including suitable fancy type brackets fixed wity rawl plug, screw etc complete all as specified. |
| 104 | S&F in repairs door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked), complete all as specified & as directed. |
| 105 | S&F in repairs brass mortice lock, vertical type, size 65mm, 2 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified. |
| 106 | S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed overall length 140 mm complete all as specified & directed. |
| 107 | S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 Ltrs hoisted and fixed in position with ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed of 20mm dia, minimum weight - 210 gms all as specified in SSR Part I including dismantaling existing water tanks complete all as specified and directed. |
| 108 | S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 Ltrs hoisted and fixed in position with ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed of 20mm dia, minimum weight - 210 gms all as specified in SSR Part I including dismantaling existing water tanks complete all as specified and directed. |
| 109 | S&F in repairs ball valves of 20mm dia, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed, minimum weight - 210 gms of including taking down existing ball valves any type complete all as specified & directed. |
| 110 | S&F in repairs vitreous china wash down water closet pan (Padestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified. |
| 111 | S&F in repairs vitreous china squatting pan 'orissa pattern' size 580 x 450 mm white with integral foot rest (ISI marked) with 'P' or 'S' trap, front or back inlet and foot rest any pattern, including connection to flushing pipe anti-syphonage pipe etc, including setting of pan & trap in lean PCC 1:5:10 complete and making good to distrubed floor with PCC or cement mortar 1:3 to match with sorroundings complete all as specified & directed. |
| 112 | S&F in repairs vitreous china wash basin white of size 550x400 mm with padestal stand (ISI marked) including 32 mm CP waste coupling & PVC flexible waste pipe of min 90 cm long, flat back or angle back type excluding taps, waste chain & plug but incuding cast iron brackets and cutting for and pinning in ends of brackets or erecting stand complete fixed in repairs all as specified and directed. |
| 113 | S&F in repairs Jet spray PVC butterfly plated for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete all as specified & directed. |
| 114 | S&F in repairs Jet spray chromium plated brass for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete all as specified & directed. |
| 115 | S&F in repairs health fusset chromium plated suitable for 15 mm bore pipe including 1 M long PVC tubes for EWC complete all as specified & directed by Engineer-in-Charge. |
| 116 | S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia complete all as specified. |
| 117 | S&F in repairs for PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as directed. |
| 118 | S&F in repairs for PVC internal fittings (kit) complete for low level flushing cistern tank, all as specified and directed by Engineer-in-Charge. Make Commander/Perryware. |
| 119 | S&F in repairs for towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to all as directed by Engr-in-charge including taking down existing towel rail. |
| 120 | S&F in repairs CP toilet paper holder with cover complete all as specified and directed. |
| 121 | S&F in repairs tank cover for 500/1000 ltr capacity tank complete all as specified and directed. |
| 122 | S&F in repairs plastic water closet seat cover white /coloured closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified an directed. |
| 123 | Supply and replacement in repairs of brass spindles, phases of brass of any size required 3/4/5 for bib taps, pillar cocks, stop cocks, angle valves, concealed valves complete all as directed. |
| 124 | S&F in repairs for MS grating CP 75/100mm dia, with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as directed. |
| 125 | S&F in repairs Brass chromium plated shower rose with long arm 150mm size fixed to 15mm bore pipe all as directed. |
| 126 | S&F in repairs waste coupling for sink as per sample approved complete all as directed. |
| 127 | S&F in repairs looking mirror 600x450mm bevelled edge 5.5mm thick selected quality glass, mounted on 6mm thick commercial ply, aluminium or Wooden frame around and fixed to wooden plug with CP brass screws and cup washeres and as directed. |
| 128 | S&F in repairs mirror cabinet (PTMT) fixed on wall with cadmium plated brass screws as per approved by GE all as directed. |
| 129 | S&F in repairs bib taps bore of pipe in 15mm, cast copper alloy, fancy type, chromium plated, with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 130 | S&F in repairs for bib tap standard of PTMT any colour 15mm bore high pressure screwed for iron pipe (Min. wt 90 gms) and complete all as specified and directed. |
| 131 | S&F in repairs 15mm bore, stop valve/angle valve,chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed. |
| 132 | S&F in repairs 15mm bore, two way angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed. |
| 133 | S&F in repairs 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed. |
| 134 | S&F in repairs PVC flexable waste pipe 32/40 mm dia & approx 900 mm long with PVC waste coupling suitable for WHB, sink & urinal complete all as specified & directed. |
| 135 | S&F in repairs Brass CP Wall mixer for mixing hot & cold water suitable for 15mm bore dia pipe screwed down for iron pipe and fixed complete all as specified and directed. |
| 136 | S&F in repairs Vitreous China urinals, half stall type, complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed. |
| 137 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. & hositing if required reconnecting & re-fixing in position. (Cleaning repairing etc. measured separately) exc 250 & n exc 500 litres complete all as specified and directed. |
| 138 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. & hositing if required reconnecting & re-fixing in position. (Cleaning repairing etc. measured separately) exc 500 & n exc 1000 litres complete all as specified and directed. |
| 139 | Cleaning & removing all scale & dirt, etc. from tanks & form mouths of circulating pipes, etc. exc 250 & n exc 500 litres complete all as specified and directed. |
| 140 | Cleaning & removing all scale & dirt, etc. from tanks & form mouths of circulating pipes, etc. exc 500 & n exc 1000 litres complete all as specified and directed. Please Enable Macros to View BoQ information |
| 141 | Cleaning & removing all scale & dirt, etc. from tanks & form mouths of circulating pipes, etc. exc 500 & n exc 1000 litres complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysSep 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender