Tender For Repairing Of No-4 Actuator Starter, Actuator Operated Butterfly Valve For Delivery Side Of Centrifugal Pump No-1 & 3, Eplacement Of Damaged Ups For Level Indicator At Amdohi Boosting Station Under Jamgara-Jagannathpur W/S Scheme.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
31 Aug 2026
16 days left
EMD
7000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Paschim Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing Of No-4 Actuator Starter, Actuator Operated Butterfly Valve For Delivery Side Of Centrifugal Pump No-1 & 3, Eplacement Of Damaged Ups For Level Indicator At Amdohi Boosting Station Under Jamgara-Jagannathpur W/S Scheme.
BOQ
| Sl. No. | Item Description |
| 1 | Actuator starter repairing portion:- |
| 2 | 9 Amp, 3 Pole power contactor, 415 V AC, 50 Hz, with 1 No auxiliary contact block, conforms to IS/IEC 60947-4-1 & IEC 60947-4-1.(Make:- L & K, Type No-MNX 9, Cat No-CS94106/Other approved make) |
| 3 | 2 NO+ 2 NC auxiliary add on contact block for 240 V AC control voltage.(Make:-L & K, Type No-MCX 01-22, Cat No-CS91107/Other approved make) |
| 4 | Thermal overload relay range from 3-5 Amp, ambient temperature compensated up to 55° C, built-in single phasing protection, manual and auto reset mode, conforms IS/IEC 60947-4-1 & IEC 60947-4-1.(Make:-L & K, Type No-MN2, Cat No-SS94141OOSO) |
| 5 | Kit for Mounting MN-2 Relay separately (Direct Mounting Type)(Make:- L & K, Cat No-SS94700OOOO) |
| 6 | Ø22.5 mm LED indicaor operating voltage-240 VAC, low power consumption < 1W, surge & low voltage glow protection (LVGP).(Make:-L & K, Cat No-EPL) |
| 7 | 1.5 Sqmm PVC insulated(Un-sheathed) FR-LSH Cu wire single core multi strand 1.1 KV grade as per IS:694.(Make:-Polycab/Gloster/Other approved make)(For Control Circuit) |
| 8 | 2.5 Sqmm PVC insulated(Un-sheathed) FR-LSH Cu wire single core multi strand 1.1 KV grade as per IS:694.(Make:-Polycab/Gloster/Other approved make)(For Control Circuit) |
| 9 | Pin/ring type socket, lugs, PVC chanels, etc. |
| 10 | Atfirst disconnection of all power line.Then fixing the above supplied materials at same place, then making power & control circuit wiring through out the local push button/starter work must be done by Experienced electrician and wholly satisfaction of EIC. |
| 11 | Actuator repairing portion- 1 & 3 centrifugal pump's delivery line:- |
| 12 | Worm shaft as per actuator specification. |
| 13 | Limit switch drive as per actuator specification. |
| 14 | Centre column as per actuator specification. |
| 15 | Burnout motor rewinding. |
| 16 | 4 Pole, AC-3 duty power contactor, 25 Amp, operating voltage-240 V AC.(Make:-Eaton, Model No:-XCTD-012) |
| 17 | Power model. |
| 18 | Worm wheel. |
| 19 | Oil seal. |
| 20 | Atfirst removing worm shaft, wheel, power related equipments from the actuator then fitting, fixing the new one also functioning all actuator operated butterfly valve at the delivery line, as per direction of EIC. |
| 21 | Level indicator UPS change:- |
| 22 | Uninterruptible Power Supply (UPS) as per IS 16242 (part-1) with overload protection, micro controller based, boost & buck AVR having following specification:- Capacity- 600VA / 360W, Input- 230V AC, Single phaseFrequency- 50/60Hz; Out put- 230V+/- 10% (AC mode)(Schneider :-APC-Back UPS) (BX600C-IN) (For Level indicator), atfirst removing of the damaged UPS from the power plug then placed new one, supply power via this. |
| 23 | Centrifugal pump starter No-03:- |
| 24 | 63 Amp, 3Pole, AC-3 duty Molded cased circuit breaker, breaking capacity-36 kA with microprocessor based tripping unit, 415 V AC, 50 Hz.(Make:-Siemens, Type No-3VA2063-4HL32-0AA0) |
| 25 | 1NO+1NC configuration auxiliary switch.(Make:- Siemens, Type No-3KJ9001-1AB00) |
| 26 | At first remove the damaged MCCB, auxiliary contact block etc from the existing panel after disconnection of all power line.Then fixing the above supplied materials at same place, then making power & control circuit wiring through out the panel work must be done by Experienced electrician and wholly satisfaction of EIC. |
| 27 | Add GST @ 18% |
| 28 | Add CESS @ 1% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysSep 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender