Tender For Repair To Roof Treatment From Roof, Reinforced Cement Concrete Chajjas, Soffits, Replacement Of Rwp And Connected Works To Certain Smqs At Sector 47 & 28 Under Ge (Af) Mc Chandigarh
Tender Value
40 Lakhs
Estimated cost
Bid Submission
03 Sep 2026
15 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Roof Treatment From Roof, Reinforced Cement Concrete Chajjas, Soffits, Replacement Of Rwp And Connected Works To Certain Smqs At Sector 47 & 28 Under Ge (Af) Mc Chandigarh
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work built in cement mortar including all quoins, arches, pillar etc.,including removing the waste materials to a distance of 500 meters complete all as specified and directed by Engr-in-Charge. |
| 2 | Demolition of roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work including cutting of chajjas at any height complete all as specified and directed by Engineer-in-Charge. |
| 3 | Dismanting bricks tiles/cement concrete tiles or terracing tiles single layer on roofs and including removing of old treatment and removal of debris away from site to a designated point by the local administration or a distance up to 1.5 km from site complete all as specified and directed by Engr-in-charge. |
| 4 | Demolition of mud phuska on roofs any thickness including mud plastering (whether full thickness removed or only a part thereof) and removal of debris away from site to a designated point by the local administration or a distance up to 1.5 km from site complete all as specified and directed by Engr-in-charge. |
| 5 | Dismantling of cast iron or reinforced concrete drain pipes,any size, jointed in cement mortar and taking out of trenches/wall/floors, complete all as specified and directed. |
| 6 | Dismantling of precast cement concrete louvres and jallies from shaft portions, any thickness up to height 10 mtr & making good the surface with Cement Mortar 1:4, including necessary scafolding/form work etc, complete removing from site, complete all as specified and directed. |
| 7 | Taking up or down GI steel/ Kitek tubing 15 mm with connections or fittings from wall, ceiling, floor etc, complete all as specified and directed. |
| 8 | Taking up or down GI steel/ Kitek tubing 20 mm with connections or fittings from wall, ceiling, floor etc, complete all as specified and directed. |
| 9 | Roughening the surfaces of old concrete roof surfaces & sides by picking, brushing with wire brush, sweeping clean and washing down with water to remove dust, excess material etc., brushing neat cement slurry with 3.0 kg of cement per Sq. m over cleaned roof surfaces complete all as specified and directed by Engr-in-Charge. |
| 10 | M&L Plain cement concrete B-1 type (1:2:4) using 20 mm graded crushed stone aggregate in padding and the like finished fair & even, including necessary form work complete all as specified and directed by Engr-in-Charge. |
| 11 | M&L for cleaning crack or groves in RCC slab / brick tiles / PCC tiles surface of width upto 25 mm and in any existing depth with compressed air to make free from all loose and foreign particals filling with Dr.fixit/ Fosroc/ Asian/ Berger Primer adhesive and white cement in equal portion (1:1) as a prime coat to level the bottom surface complete all as specified and directed by Engineer-in-Charge. |
| 12 | M&L for providing, mixing and applying Dr.fixit/Fosroc/Asian/Berger Primer with 10% water dilution with clean portable water and applying with roller or brush coverage at the rate 7.0 to 8.0 sqm per litre/coat. Allow the primer to dry for 04 hrs. and applying a coat of Dr.fixit/Fosroc/Asian/Berger roof seal select (diluted with water in the ratio 2:1) self priming coat at the rate 8-10 sqm/litre/coat in the SSD condition. Apply 1st coat of Dr.fixit/Fosroc/Asian/Berger roof seal select at the rate of 0.45-0.5/ litre/ sqm/ coat. Laying a 45 GSM glass fibre mesh of 2.5mmX2.50mm sandwiched between the first and second coat. While the first coat is still wet allow the first coat to dry for 4-6 hrs. Apply second coat of Dr.fixit/Fosroc/Asian/Berger roofseal select with the same application coverage. Application direction of second coat should be perpendicular to the first coat. Allow second coat to dry for 4-6 hrs. Apply third coat of Dr.fixit/Fosroc/Asian/Berger roofseal select at an application direction that is perpendicular to that of the second coat with the same application coverage rate to achieve total dry film thichness of 900 to 1000 microns at forced coverage at the rate of 1.50-1.60 litre/sqm in 3 coats. Check to see no void surface is untreated / uncoated. Allow the system to air cure for 7 days minimum. The material having following technical properties: Attains a tesile strength with fibre N/mm 2=6-8 as per ASTM D 2370; Elongation at break = 200% as per ASTM D 2370, Crack bridging ability up to 2mm, Shore-A hardness 80 as per ASTM D2240-2015, Tear Resistance with fibre N/mm 34 as per ASTM D 624. The system comes with 12 year waterproofing warranty from M/S Pidilite Industries/FOSROC/Asian/Berger complete all as specified and directed by Engineer-in-charge. |
| 13 | All as per item 12 here-in-before but as in chajjas |
| 14 | M&L for Rough cast plaster including after applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick with WPC@1% and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered complete all as specified and directed, including taking down cement plaster and racking out joints, hacking for key scrubbing down with water etc, complete all specified and directed by Engr-in-Charge. |
| 15 | M&L for Preparation of new plastered /unplastered Wall surface and applying two coats of cement base paint over priming coat, complete all as specified and directed by Engr-in-Charge. |
| 16 | Cutting of groove V shape chases, pinning in ,making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings,steps, cills , sunshades, shelves, lintel etc and making good cutting of n exc 10 cm girth in brick walls making good complete complete all as specified and as directed by the Engineer -In -Charge |
| 17 | Cutting Small trees/ peepal trees girth not Exc 15 cm including cutting of trunk portion protuding over wall surface/roof surface/terrace of building of height up to 10.0 mtr. Including necessary scaffolding and necessary safety measure if required and make good the surface in cement mortar (1:3) and applying one coat of anti growth of vegitation chemical as directed by Engr-in-Charge and removing of unserviceable material out side MD land and cleaning site complete all as specified and directed by Engr-in-Charge. |
| 18 | M & L for racking out joints of brick or pcc tiles joints laid on roof with compressed air to make free from all loose dirt and do flush pointing to the joints in Cement Mortar 1:3 with WPC @1% complete all as specified & directed. Contractor Rate also including for fixing of any loose tile if any and making good as per best engg terms. |
| 19 | Taking down cement plaster of any description on brick or stone walls etc, including raking out joints, hacking for key scrubbing down with water, etc , complete all as specified and directed by Engr-in-Charge. . |
| 20 | M&L for Rendering 15mm thick in Cement Mortar 1:4 on brick work, concrete, R.C.C. Surfaces on mumty , parapet or similar surfaces at any height finished even and fair without using extra cement of ,up to height 12 mtr with proper scaffolding etc complete all as specified and directed by Engr-in-Charge. |
| 21 | M&L for preparation of new / old surface of wall / coloum ,beam , chajja etc. and leveling / edgesing the disturbed surface a thin layer of putty and making smooth by using sand paper applying two coat of exterior acrylic emulsion (weather proof treatment) including one coat of exterior primer including necessary scaffolding complete all as specified and as directed. |
| 22 | M & L for preparation of old surface of wall and applying one coat of OBD white or tinted to be applied using airless spray machine complete all as specified & directed. |
| 23 | M & L for preparation of old surface of wall and applying two coats of OBD white or tinted to be applied using airless spray machine after a coat of 2mm thick wall care putty complete all as specified & directed. |
| 24 | M & L for preparation of old surface of Ceiling and applying one coat of OBD white or tinted to be applied complete all as specified & directed. |
| 25 | S&F repair Rotational moulded polyethylene water storage tanks lid with clips, screws locking device complete for 500/1000 ltr tanks capacity complete all as specified and directed by Engr-in-charge. |
| 26 | S&F in repair PVC (SWR) pipes 110mm dia Single socketed, in any length with rubber ring joints fixed to walls , laid in trenches, floors etc complete all as specified and directed by Engr-in-charge. |
| 27 | S&F in repair for 110mm PVC (SWR) Tee & branch pieces equal and unequal complete all as specified and directed by Engr-in-charge. |
| 28 | S&F in repair for 110mm PVC (SWR) bends any radius complete all as specified and directed by Engr-in-charge. |
| 29 | S & F in repair GI water tubes, 15 mm bore medium grade, galvanized with all GI/Kitek fittings, tank Nipple etc, and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed by Engr-in-charge. |
| 30 | S & F in repair GI water tubes, 20 mm bore medium grade, galvanized with all GI/Kitek fittings, tank Nipple etc and fixed complete to walls, ceiling or laid in floors complete all as specified and directed by Engr-in-charge. |
| 31 | S & F in repair rotational moulded polyethylene water storage tank white colour (Cylindrical vertical with close top), HDPE, triple layered with ISI marked of 500 ltrs capacity with inlet & outlet connections, including 20mm dia PVC float valve with ball & all fittings, tank nipple 150 mm long with washer & plug , with tank lid having locking arrangement hoisted and fixed in position complete all as specified and directed complete all as specified and directed by Engr-in-charge. |
| 32 | S&F in repairs Ball valves high pressure PTMT ISI marked, with epoxy coated alluminium rod and high density plastic ball screwed for iron pipe of 15 mm bore (minimum weight 210gm) fixed in repair complete all as specified and directed by Engr in Charge. |
| 33 | S&F in repairs Ball valves high pressure PTMT ISI marked, with epoxy coated alluminium rod and high density plastic ball screwed for iron pipe of 20mm bore (minimum weight 210gm) fixed in repair complete all as specified and directed by Engr in Charge. |
| 34 | S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, 20 mm bore screwed both end for iron pipe , and fixed in repairs complete all as specified and directed by Engineer-in-Charge. |
| 35 | M & L for brick work with sub class 'B' old size bricks straight or curved on plan exc 6m mean radius in cement mortar 1:4 for working height up G +3 storeyed building complete all as specified and directed by Engr-in-Charge. |
| 36 | All as per item 35 here-in-before but except bricks. |
| 37 | M&L for Reinforced cement concrete (Nominal mix) 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in chajjas, facia etc shelves and the like, at any height, including necessary formwork complete all as specified and directed by Engr in Charge. |
| 38 | S&F for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engr in Charge. |
| 39 | M&L for disconnecting of PVC tank of capacity 500 Ltrs & 1000 ltr for tank cleaning all as specified and directed :-a) Dewatering & removing all settled silt, scale & dust from inside of tanks using coconut brush manually and applying bleaching powder and allowed to rest for 1 hour.b) Cleaning & rinsing the tank using fresh water to wash out complete and allowed to dry for 30 mins.c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning/date sticker fix on tank including rubbing out old letters written over the tankd) Refixing the tank in same position or raised/lower height after cleaning or water proofing treatment (as may necessary) complete all as directed by engr-in-charge. |
| 40 | Supply & fix in repairs MS angle iron or tee sections, framed brackets of angles or tees,(not exceeding 10 Kg each bracket) conforming to Fe-290.Grade-E-165, purlins for fixing roof / fixing sheets as in chhajjas with coach screws and washers with 20mm wide x 3mm thick tie to frame work and fixed to walls/supports by means of dash screw bolts of suitable size including distance pieces, cleats etc. and welding and two coat of synthetic enamel paint over a coat of primer complete all as specified and directed. |
| 41 | Material & Labour in repairs providing galvalume chajja of anticorresive prepainted /colour coated base sheet of thickness 0.50mm TCT having high tensile strength not less than 550Mpa yield strength CR steel base metal with hot dip alloy coating of A1 Zn-Si as per ASTM-A-792 M-02/AS-1397 ALU-SINC alloy sheet shall be of alloy of 55% Aluminium +43.5 % zink+1.5 % silicon . The total coating of alloy shall not be less than 150 gms per sqm (AZ) 150) as per ASTM 792 of AS 1397 with top coat of 20 micron s (DFT) over 5 micron (DFT) or epoxy primer and back coat with 5 Micron (DET) epoxy primer . The sheet shall be fixed to purlin with self drilling and self topping screw confirming to AS 3566of ITW Bolldex corroshield make with moulded EPDM washer all as specified and directed by Engineer in- Charge. |
| 42 | S&F in repair 100 mm cast iron soil waste and vent pipe, sand cast pipes in any length with or without ears jointed with cement mortar (1:3) laid in trenches or in floors or on wall fixed, with clamps of MS flat iron of size 25x3mm thk with necessary nut bolts complete all as specified and directed by Engr-in-Charge. |
| 43 | All as per item 42 here-in-before but 75 mm. |
| 44 | Fixing only in repairs 100 mm cast iron soil waste and vent pipe in floors or on wall (material retrived from item no 42 here-in-before) including cleaning and fixing with clamps of MS flat iron of size 25x3mm thick with necessary nutbolts, complete all as specified and directed by Engr-in-Charge |
| 45 | All as per item 44 here-in-before but 75 mm. |
| 46 | S&F in repairs 100 mm cast iron bends complete all as specified and directed by Engr-in-Charge. |
| 47 | All as per item 46 here-in-before but 75 mm. Please Enable Macros to View BoQ information |
| 48 | All as per item 46 here-in-before but 75 mm. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender