Tender For Special Repair Of Road At Depot Area At Od Kolkata Under Ge Central Kolkata
Tender Value
1.08 Crore
Estimated cost
Bid Submission
10 Sep 2026
25 days left
EMD
1.83 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kolkata → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair Of Road At Depot Area At Od Kolkata Under Ge Central Kolkata
BOQ
| Sl. No. | Item Description |
| 1 | NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. |
| 2 | Material & labour of repair to pot holes of any depth not exc 1.00 Sqm each incl sweeping free from dust and mud or water, scoring sunken surfaces in roads, paths etc and cutting around edges to at least 25mm in depth and making good by applying tack coat of bitumineous primer VG-10 at 5 kg/ 10 Sqm putting in premixed bituminous macadam, well rammed and sealed with binder [email protected] kg per 10 sqm, binded with 0.09 cum of stone chippings, 6.3mm size and again well rammed complete all as spd & directed. Depth of pot holes exc 30 mm. |
| 3 | Material & labour for preparation of existing black top surfaces by brushing with wire brush for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified & directed. |
| 4 | Material & labour for applying evenly a priming / tack coat with bituminous primer by using paving bitumen VG-10 grade @5Kg per 10 Sqm of road surface complete all as specified and directed |
| 5 | Material & Labour of Bituminous premixed carpet 20mm thick (consolidated thickness) consisting of 0.27 Cum/10 Sqm of stone chippings mixed with 14.60 Kg/10 Sqm of paving bitumen(VG-30) and spread rolled with 8 to 12 tonne power roller and to required camber and gradient complete all as specified and directed |
| 6 | Material & labour for applying a tack coat over existing bituminous surface @ 0.5 Kg/Sqm of 20/30 bitumen and providing and laying 20mm thick bitumen mastic asphalt on prepared surface strictly in accordance with IS specification No5317-2002(As latest modified) with mastic i.e. bitumen of grade 20/30 @4.50 Kg /Sqm (minimum) mixed stone dust (lime stone powder with calcium value 80%) @0.008 Cum/Sqm and stone chipping of size 12.5mm and 10mm @0.0096 Cum/Sqm and sand @0.004 Cum per sqm and inerting stone graded of 22mm size with 0.017 Kg/Sqm of 20/30 bitumen per Sqm for anti skiding including all tools and plants etc complete all as specified and directed. |
| 7 | Material & labour for preparing bituminous surface of road and marking 2.5 mm thick centre lines, stop lines, dashes, arrows, letters, zebra cross etc and the like n.exc 10cm wide on roads, pavements with hot applied thermoplastic road marking paint of approved colour as per IRC 35 conforming to BS 3262-1989 with 20% glass beads (intermixed), spread and laid by automatic mechanical machine engine drive complete all as specified and as directed. |
| 8 | Supply and fixing in repair plastic speed bump of 750mm length x 250mm width x 75 mm high and made of ABS material with 2 nos high reflective reflectors moulded in PMMA and fixed with 4 nos nail and epoxy adhesive (base bumper & hole) on road surface complete and fixing as per manufacturer's instruction and all as directed by Engineer-in-Charge. |
| 9 | Supply and fixing of Cat's eye Road stud, solar reflective type, metal body alloy, size 100mm x 100 mm x 20mm with PAMA striplens reflector with and incl MS stud of suitable size complete and fixing as per manufacturers instructions and all as directed by Engineer-in-Charge. |
| 10 | Supply and fixing of Solar Stud (blinker), aluminium alloy (100% water proofing design ) of size 125mm x 125mm x 25mm (shank 65mm) of high efficieny Mono crystaline solar panel 2.4V / 0.3 watt one Ni-mh rechargeable battery (1.2V / 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd complete and fix to road with epoxy based adhesive as per manufacturers instructions and all as directed by Engineer-in-Charge. |
| 11 | Supply and fixing of sign board of retro reflective high intensity prismatic grade sheet of any colour / type as per type-IV of ASPN D-4956 mage of aluminium sheet 2.00mm thick cut to size of 1.20 x 0.9 mtr fixed to hollow MS square tube (Medium Grade), 2.5mm wide (2 Nos all round) frame work by keeping aluminium sheet in between two MS square tube incl necessary rebating, bolting to join the the sheet, welding 4 Nos MS bolt (2 Nos at either ends) to fix / hang the signboard, fixing the board upon 02 Nos GI pipe (medium grade) 40mm bore 2.0 mtrs high support (vertically) abobe GL and grouting end in PCC block of size 40 x 40 x 50 cm 1:3:6 type C2 incl necessary earthwork, returning / filling, removal of surplus earth etc and applying two coats of synthetic enamel paint ove a coat of red oxide primer on exposed steel surfaces incl dismantling existing sign board and removing from site complete all as specified and directed |
| 12 | Supply and fixing of metal tubular delineators made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45 / 50mm dia mild steel pipe duly powder coated of 600 mm height and thermo plastic elastomer 3 band of green, red and yellow reflector radium tape of 25mm wide strips with anti theft steel net for reflector protection including embedding the dealineator to the ground by means of PCC 1:2:4 type B1(using 20mm graded stone aggregate), block of size 150 x 150 x 300mm all as specified & directed by Engineer-in-Charge. |
| 13 | Supply and fixing in repair of Road safety convex mirror of 800mm dia, pole mounted on MS heavy grade pipe 50mm dia duly powder coated with anti-rust paint, 1.2 metre high from GL with 300 mm (minimum) embedded in ground and including necessary PCC M-10 (using 40mm graded stone aggregate) block and two coats of paint by hot pressing over a coat of red oxide around the pipe in full perimeter all as per IRC complete and as directed by Engineer-in-Charge. |
| 14 | Dismantling stone slabs and tiles of laid in bedded and pointed in any mortar any description or thickness in floors, aprons etc all as directed. |
| 15 | Demolition of cement concrete (un-reinforced) of any description, not exc 150mm thick, above or below ground level complete all as directed. |
| 16 | Material & labour for 75mm thick PCC M-10(Nominal Mix) (using 40mm graded crushed stone aggregate) as in sub-bases of flooring complete all as specified and directed. |
| 17 | Material , Labour and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade confirming to IS 15658-2006 with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 18 | All as per item No 17 here-in-above but re-laying existing paver block with 50mm thick compacted bed of fine sand complete all as specified and as directedNote:- Existing paver Block shall be re-used. |
| 19 | Material & labour for PVC(SWR) pipe single socketed, in any length, laid in trenches or in floor 110mm dia of pipe complete all as specified and directed. |
| 20 | Material & labour for preparation of old surfaces of brick, stone, concrete or plaster surfaces of any description over 10 cm girth and applying two coats of floor paint complete all as specified and directed. |
| 21 | Demolition of brickwork, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and as directed. |
| 22 | Material and labour for brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed. |
| 23 | Material & labour for cement concreteM-15(Nominal Mix) as in copings, kneelers, apex stones, bed plates, kerbs, water throughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 24 | Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately |
| 25 | Demolition of cement concrete of any description in manhole / septic tank cover slabs in any position complete all as specified and directed. |
| 26 | Material and labour for Precast Reinforced Cement Concrete 1:1.5:3 type A-1 as in cover slab, landing salb etc set in CM 1:4 complete all as specified and directed. |
| 27 | Supply and fixing TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete in all respect as specified and directed. |
| 28 | Material and labour for Painting 2 coats of synthetic enamel paint on concrete surfaces of any description over 10 cm in width or girth including preparation new surface and one coat of primer complete all as specified and as directed. |
| 29 | Note: Schedule of credit (SCHEDULE OF CREDIT) amount shall be deducted from the total quoted amount of BOQ. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysSep 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 32 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender