Tender For Comprehensive Maintenance To Bldgs At Navy Park Area, Material Organisation, Sagar Vihar, Jcda, Nscb & Other Minor Units Of Age B/R-Ii Under Ge Haddo, Sri Vijaya Puram
Tender Value
42 Lakhs
Estimated cost
Bid Submission
02 Sep 2026
10 days left
EMD
84000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Maintenance To Bldgs At Navy Park Area, Material Organisation, Sagar Vihar, Jcda, Nscb & Other Minor Units Of Age B/R-Ii Under Ge Haddo, Sri Vijaya Puram
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling structural steel work including doors, gates but excluding framed truss etc.complete all as specified and directed. |
| 2 | S&F for roof trusses (framed), trussed, purlines, and fasteninf and heavy brackets framing (beam, tee, angle, channel or flats section) including distance pieces, cleat etc conforming to Fe-410 (Gde-E250) quality -A complete all as specified and directed. |
| 3 | S&F mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. |
| 4 | Dismantling plain or corrugated steel sheeting, any gauge, for roof coverings in small patches all as specified and directed. |
| 5 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 6 | S&F for pre painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in roof covering fixed with self tapping screws as specified. |
| 7 | S&F in repairs aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering complete all as specified and directed. |
| 8 | Taking down and removing all kind of existing roof treatment by chiseling/ mechanically etc from the roof slab, parapet wall and other affected area by cutting edges, cleaning the dismantled portion with wire brush etc to make the surface remove from dust, dirt and other foreign particle etc and removing debris 50 Mtr from site all as specified by Engineer-in-Charge |
| 9 | M&L 20 mm thick screed bed Plaster on RCC roof slab with CM ( 1:4 ) including water proofing compound @ 200ml per 50 Kg cement bag shall be carried out as specified. (Note WPC shall be measured and paid separately) |
| 10 | Supply only integral water proofing compound |
| 11 | Demolition of cement concrete of any description and in any position, sunken floor /roof padding etc not otherwise specifically provided for complete all as specified and directed. |
| 12 | M&L for providing PCC (1:2:4) type, B-0 (using 12.5 mm graded stone aggregate) as in roof padding /sunken floor and similar work all as specified and directed. |
| 13 | M&L for applying a coat of cold bituminous primer over cleaned surface @ 0.30 Kg/Sqm and applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg/Sqm over primer followed by APP modified polymeric membrane 3mm thick, minimum weight not less than 3 Kg/Sqm, reinforced with polyester non-woven fabric weight not less than 150 Gm/Sqm laid as per the manufacturer's instruction with side over lap of 100mm and end over lap of 150mm, tucked into the chases on vertical surfaces and painting over APP membrane sheet with aluminium paint @ 0.10 Kg/Sqm complete all as specified and directed |
| 14 | Cutting channels, grooves or rebates with or without reinforcement n exc 15cm girth, and trimming surface for embedding the APP membrane sheet into the wall column surface complete all as specified and directed. |
| 15 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressivestrength of 58 N/mm2modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 16 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 17 | Dismantling water tanks of 1000 ltrs capacity complete all as specified and directed. |
| 18 | M & L for 1000 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete. |
| 19 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing etc. measured separately). Exc 250 n exc 500 |
| 20 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing etc. measured separately). Exc 500 n exc 1000 |
| 21 | Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed |
| 22 | Supplying and laying of 25mm outer dia CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified. |
| 23 | Supply and fixing 25 mm outer dia union |
| 24 | Supply and fixing 25 mm outer dia Brass Tee |
| 25 | Supply and fixing 25 mm outer dia CPVC pipes brass Elbow |
| 26 | Supply and fixing 25 mm outer dia CPVC Male Brass Threaded Adaptor (MTA/MBTA). |
| 27 | Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed |
| 28 | Supplying and laying of 20mm outer dia CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified. |
| 29 | Supply and fixing 20mm outer dia union |
| 30 | Supply and fixing 20 mm outer dia Brass Tee |
| 31 | Supply and fixing 20 mm outer dia CPVC pipes brass Elbow |
| 32 | Supply and fixing 20 mm outer dia CPVC Male Brass Threaded Adaptor (MTA/MBTA) |
| 33 | Providing and fixing fluted decorative wall panelling of approved design and pattern made out of high-density moisture resistant WPC/PVC/MDF fluted panels of size and profile as approved by Engineer-in-Charge, having minimum thickness 8 to12 mm with vertical linear grooves/flutes at regular intervals, finished in approved shade, texture and laminate/PU/polish finish complete. Panels shall be fixed over framework/base surface with approved quality polymer based adhesive and additionally secured with stainless steel screws/clips wherever required. Joints shall be finished neatly to true line and level including edge trims, corner mouldings, cutting for electrical boxes/switches, necessary backing arrangement, scaffolding and all incidental works complete.The work shall include preparation of wall surface, cleaning, rubbing, alignment, proper spacing, sealing of joints, touch-up finishing and making good disturbed portions to match adjoining surfaces complete in all respects as specified and directed by Engineer-in-Charge. |
| 34 | Dismantling of floor hearth or wall tiling in patches not exc 3.0Sqm each (not exc 0 .6 mtr wide and any length) including cement mortal bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 35 | M&L for coloured Glazed ceramic tiles in vertical surfaces 350x250x7mm/300x450x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:3 complete all as specified and directed |
| 36 | M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:4) complete all as specified. |
| 37 | M&L for non-skid Ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. and including 15mm thick layer of screed bed in cm 1:4 on floor surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 38 | M&L for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 Sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed |
| 39 | M&L for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 Sqm (600x600mm) in vertical surfaces such as skirting, dados and riser etc set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:3 complete all as specified and directed |
| 40 | M&L for vitrified Double Charged ceramic tiles minimum 8-10 mm thick (square/ rectangular) polished area of each tiles exc 0.42 Sqm but n.exc 1.00 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed |
| 41 | M & L for providing 100 mm thick, PCC 1:4:8type D2 using 40 mm graded stone aggregate as in sub base of floors complete all as specified and directed. |
| 42 | S&F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging, fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 43 | Dismantling of 110mm dia cast iron/PVC pipes incl bends/branch pieces jointed in cement mortar and taking out if reqd complete all as specified and directed. |
| 44 | S&F PVC (SWR) pipe 110mm bore, single socketed, in any length including bends, socket etc with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed |
| 45 | S&F PVC (SWR) pipe 110mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed |
| 46 | S&F PVC (SWR) 110mm dia bend of any radius and jointed with approved adhesive complete all as specified and directed |
| 47 | M & L PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) 25mm thick as in levelling course, sub-floors and paving etc complete all as specified. |
| 48 | Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level complete all as specified and as directed. |
| 49 | Taking down chowkhats or frames area n. exc 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed |
| 50 | Taking down Chowkats exc 1.5 Sqm but n. exc 4 Sqm each with shutters (Without taking off shutters from the frame) complete all as specified and directed |
| 51 | Providing and fixing factory made uPVC white colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5 mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessoriesNet opening will be measured for payment purpose |
| 52 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators, partitions and their shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 53 | Supply only 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 54 | S & F for Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed. |
| 55 | S&F Powder coated aluminium grill of approved pattern cut to required size/shape and fixed with position with aluminium bedding & frame with & including F sections, fixed to aluminium windows/ventilators complete all as specified and directed. |
| 56 | M&L for applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth after complete removal of existing treatment complete all as specified and directed |
| 57 | M&L for 10mm thick plaster in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified |
| 58 | M&L for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed |
| 59 | M&L for applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty on ceiling after complete removal of existing treatment complete all as specified and directed |
| 60 | M&L for preparation of old decorated surfaces of walls and cornices by broomingn down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots etc and applying one coat of distemper oil emulsion complete all as specified and as directed. |
| 61 | M&L for preparation of old surfaces of ceilings and cornices by broomingn down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots etc and applying one coat of distemper oil emulsion complete all as specified and as directed. . |
| 62 | M&L for preparation of old surfaces of steel surfaces exceeding 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed by Engr-in-Charge. |
| 63 | Dismantling of ceiling boarding in description fixed in any position complete all as specified and directed. |
| 64 | M & L for seamless gypsum board false ceiling 12mm thick including for any sunk or raised moulding with 25mm long self drilling/ tapping screws having philips head with joining compound and 48mm wide fiber tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flange of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm suspended from soffit at approx 900mm c/c with GI cleats and steel expansion fasteners with and incl ceiling section ( not exc 1.2m length) of 0.55mm thick having kurled web of 50mm an flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting across the intermediate channel at 457mm c/c incl hangers 6mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete and finally applying two coats of oil bound distember with roller finish over a coat of primer. |
| 65 | M&L for anodised aluminium snap grid frame work for false ceiling 605mm x 605mm using aluminium anodised sections as specified in SSR Part-I-1991 including cutting, drilling, jointing etc complete including provn of 3mm dia GI hangers wire suspenders fixed with adjustable connectors and providing 4mm thick E-Boards (Classic) 605mm x 605mm size duly applied with two coats of oil bound distemper ovoer a coat of primer all as specified. |
| 66 | Supply only stainless steel IMAX hinges for aluminium window shutters. |
| 67 | Hacking out old broken glass(any thickness, size, quality or description) from wooden frames /steel frame/aluminium frame or stone, concrete or brick surrounds , glazed with putty or fixed with beads all as specified and directed . |
| 68 | S&F Sheet glass 4.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window shutter n.exc 0.5 sqm in each pane all as specified and directed |
| 69 | Supply only sheet glass 5.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium door/window/ventilator shutter not exc 0.5 Sqm in each pane complete all as specified and directed. |
| 70 | S&F figured glass, pin head type sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter not exc 0.5 Sqm in each pane complete all as specified and directed. |
| 71 | Supply only aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples all as specified and directed |
| 72 | S&F in repairs Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples |
| 73 | S&F in repairs 100mm size stainless steel butt hinges medium weight complete all as specified |
| 74 | S&F in repairs 200mm aluminium, anodised/Powder coated, barrel tower bolts of extruded section all as specified |
| 75 | S&F in repairs 150mm aluminium, anodised/Powder coated, barrel tower bolts of extruded section all as specified |
| 76 | S&F in repairs150mm size extruded aluminium alloy handles, fabricated type, anodised/Powder coated all as specified |
| 77 | S&F in repairs 250 mm long aluminium, anodised/ powder coated sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet sliding bolts of extruded sections and fixing bolts and sliding bolts of extruded section all as specified |
| 78 | S&F in repairs door closer hydraulically regulated aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified Please Enable Macros to View BoQ information |
| 79 | S&F in repairs door closer hydraulically regulated aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysSep 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender