Tender For Eshtablishment Of Centre Of Excellence For Apricoat At Model Orchard Cum Nursery Kurbathang Kargil. Under Sdp
Tender Value
6.38 Crore
Estimated cost
Bid Submission
29 Aug 2026
5 days left
EMD
12.77 Lakhs
Bank guarantee accepted
Document Fee
6380
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kargil → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Eshtablishment Of Centre Of Excellence For Apricoat At Model Orchard Cum Nursery Kurbathang Kargil. Under Sdp
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :All kinds of soil : |
| 2 | Soling-Dumping of stone including cost of stone |
| 3 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete. |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms. |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for: Slab Edge Shuttering |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for: Stairs (excluding landings) except spiral staircases. |
| 11 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, column, pillars, piers, abutments, posts and struts etc. upy floor five level excluding cost of centering, shuttering, finishing and reinforcement: (1:1.5:3) 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). |
| 13 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 5.3.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 14 | Steel Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. (Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 15 | Providing and laying autoclaved aerated cement blocks masonry with150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 16 | Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:3:6(1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size) |
| 17 | CEMENT PLASTER (IN FINE SAND) 12mm Cement plaster of mix:1 : 4 ( 1 cement : 4 fine sand) |
| 18 | 6mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 19 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1 mm thick |
| 20 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. Water thinnable cement primer |
| 21 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) |
| 22 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.1 mm thick |
| 23 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 24 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 25 | Providing and fixing 100mm Pine wood plain lining tongue and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface. 10mm thick |
| 26 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing,- M.S. tube |
| 27 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished 40 mm thick with 20 mm nominal size stone aggregate |
| 28 | 20mm cement plaster finished with a floating coat of neat cement of mix : 1 : 3 ( 1 cement : 3 fine sand) |
| 29 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600x600 mm |
| 30 | LAMINATED FLOORING :Providing and fixing Interlock Laminate (AC-4) on floors including necessary fittings and accessories.All Job Complete |
| 31 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment ofmatching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab with Shade as approved by Architect in charge. |
| 32 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood |
| 33 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 34 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 35 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 250x10 mm |
| 36 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of leverhandles of approved quality with necessary screws etc. complete. |
| 37 | Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete : 125x90x4.00 mm |
| 38 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a) Twin rubber stopper |
| 39 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.Of make Godrej, Dorma or equivalent |
| 40 | Providing and fixing factory made uPVC White colour Double glazed windows/ Doors comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming processofrequired length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. Cost inclusive of Single / double glass panes and silicon sealant ). Double Glazed Panes to have inert gas(Argon) filled gap and UPVC Door shutter( wherever required). All job Complete Make Kommerling, Fenesta or equivalent. |
| 41 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequenceas detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3.On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/ grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in- Charge. (Final coat to be done in 1 or 2 layers without gap of time.) Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm)made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both havingwall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead ofappropriate dimension. (Area of window above 1.50 sqm). |
| 42 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing |
| 43 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceilingwith dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, towhich the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimetre channels 0.5 mm thick 27 mm high having flanges of 20mm and 30 mm long, the perimetre of ceiling fixed to all/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges ofthe board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimetre channels suitably fixed, all complete asper drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). |
| 44 | Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; Budloo wood |
| 45 | Dry random rubble masonry with hard stone in foundation and plinth: 7.3.1 With bond stone. |
| 46 | Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour ofM -30 grade made of C&D waste by block making machine with vibratory compaction laid in required patternand including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. allcomplete as per the direction of Engineer-in-charge. |
| 47 | Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :Medium shade pigment using 50% white cement, 50% ordinary cement |
| 48 | Providing and applying polyurethane insulation foam in the exterior cavity walls of thickness 3 inches.All work complete |
| 49 | Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (Hessian based self finished bitumen” felt) and fourth and final course of stone grit 6mm and down size or peasizedgravel spread at 6 cubic diameter per square metre including preparation of surface but excluding grading complete with : Bitumen felt (Hessian base) type 3 grade I conforming to IS : 1322. |
| 50 | Providing and fixing Precast Concrete Kerb Stone blocks of size 300x300x100mm as per sample approved |
| 51 | Providing and Fixing of Acrylic sign board with lettering)The height ,written text, colour,font and size of board to be decided as per architect in charge . To be installed with necessary signage lighting and wiring.All work complete |
| 52 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 53 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 54 | Providing and fixing plained eaves boarding.2nd class kail wood.300x40 mm (nominal size) |
| 55 | Providing and fixing eaves boarding/Weather boarding of GI Sheet including all fixture complete 2mm |
| 56 | PLUMBING BOQ |
| 57 | Supply and install white vitreous china Rimless single piece water closet (European type) with Soft close slim seat cover (size: 655mmx355mmx720mm), and CP flush bend with fittings and C.I. brackets, 40mm flush bend, S Trap 220mm, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required(Make: Jaguar Cat No.CNS-WHT-851S300SPP, Essel Cat No. 77091653, or equivalent) |
| 58 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :17.1.1 White Vitreous china Orissa pattern W.C. pan of size 590x445mm with integral type foot rests.(Make Essel Cat No. 75013010 , Jaguar CatNo. CNS-WHT-OP01 or Equivalent) |
| 59 | Supply and install white vitreous china urinal with spreader of size 355x340x535mm approx. having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer. (Make:Jaguar Cat No. URS-WHT-13261H, Essel Cat No. 73011010, or equivalent) |
| 60 | Providing & fixing glass urinal partition of Height: 900mm,Width: 450mm &Frosted Safety Glass: 8 mm with fixed with expandable anchor fasteners with C.P. brass bolts and washers, embedded in wall with anchor and set in cement concrete complete including cutting and making good the walls wherever required (Make: Jaguar Model No. 1810-US/1810-UC or equivalent) |
| 61 | Supply and install thin rim Wash basin vanity in white color for over counter mounting (Size:463mm x 325x 135mm), specially fabricated brackets, painted white, 32mm dia CP waste coupling and 12 \\" bottle trap with nipple, nut, ring and rubber washer etc complete. with C.P. wall flange and rubber adopter for waste connection, complete including cutting and making good the walls, wherever required. (Make: Jaguar Cat No. Solo SLS-WHT-6901, Essel Cat No. 72031300, or equivalent) |
| 62 | Supply and install CP brass single lever hi flow wash basin mixer with wall mounted exposed part and concealed installation- Diverter (35mm) complete including cutting and making good the walls where required. (Make: Jaguar Cat No. OPP-15233NKPM, Essel Cat No. 132301(Exposed Part) ,180208(Concealed Part) , or equivalent) |
| 63 | Fixing testing and commissioning of white vitreous china adjustable type wash basin with elbow oprated tap for handicap toilet (size as per architect/client), specially fabricated C.I./M.S. brackets, painted with two or three coats of enamel paint of approved shade over a coat of primer, 32 mm C.P. brass waste and C.P.brass cast brass bottle trap and pipe to wall with C.P. brass flange and rubber adopter for waste connection complete including filling gap between counter and wash basin with approved type poly sulphide sealant, 32 mm dia seamless stainless steel tube coated with nylon non-slip gripping surface 600 mm long grab bar complete with all accessories. Including cutting & making good the walls & floors wherever required. |
| 64 | Supply and install Stainless Steel kitchen sink (Size: 24\\"' x 18\\" x 9\\") (SS 304)without drain board as per manufacturers specification and direction of Engineer with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. (Make: Essel Cat No. 534124, or equivalent) |
| 65 | Supply and install CP brass Sink mixer - wall mounted with full motion 355mm extended spout and aerator complete including cutting and making good the walls where required.(Make: Jaguar Cat No. LYR-CHR-38165, Essel Cat No. 131269, or equivalent) |
| 66 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required : Size 450x300x150mm |
| 67 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15mm nominal bore. |
| 68 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore |
| 69 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 70 | Providing and fixing toilet paper holder : C.P. brass |
| 71 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 72 | Providing and fixing 1200x900 mm beveled edge mirror of superior glass (of approved quality) complete with SS frame to be installed with screws and washers all complete. |
| 73 | Supply and install of 600 mm long ss towel rail including cutting and making good the walls, wherever required. (Make: Jaguar Cat No.ACN-1111BSM, Essel Cat No.140022 or equivalent) |
| 74 | Providing and fixing CP brass 600 mm 32mm dia grab bar with brackets fixed to wall with CP brass screws with concealed fittings complete in all respects including cutting and making good the walls. |
| 75 | Providing and fixing soundproof Multilayer Polyproplene piping system as per EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP in white color and three layer fittings in PP MD, push-fit type,Halogen and Calcium free, having high impact resistance as per DIN EN ISO 291:2008-08 , Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of not more than 17 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15gms/cm3, elongation = 0.09mm/m0K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring. (Including pipe, fittings and supports complete in all respect.)40 mm OD (class 3 (6 kg/cm2) |
| 76 | Providing and fixing soundproof Multilayer Polyproplene piping system as per EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP in white color and three layer fittings in PP MD, push-fit type,Halogen and Calcium free, having high impact resistance as per DIN EN ISO 291:2008-08 , Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of not more than 17 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15gms/cm3, elongation = 0.09mm/m0K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring. (Including pipe, fittings and supports complete in all respect.)50 mm OD (class 3 (6 kg/cm2) |
| 77 | Providing and fixing soundproof Multilayer Polyproplene piping system as per EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP in white color and three layer fittings in PP MD, push-fit type,Halogen and Calcium free, having high impact resistance as per DIN EN ISO 291:2008-08 , Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of not more than 17 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15gms/cm3, elongation = 0.09mm/m0K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring. (Including pipe, fittings and supports complete in all respect.)63 mm OD (class 3 (6 kg/cm2) |
| 78 | Providing and fixing soundproof Multilayer Polyproplene piping system as per EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP in white color and three layer fittings in PP MD, push-fit type,Halogen and Calcium free, having high impact resistance as per DIN EN ISO 291:2008-08 , Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of not more than 17 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15gms/cm3, elongation = 0.09mm/m0K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring. (Including pipe, fittings and supports complete in all respect.)100 mm Dia |
| 79 | Providing and fixing Polyproplelene (PP) P-Trap including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 hand stone ballast 20 MM nominal size) the inlet from floor level to trap rim to be grouted and cemented neat manner including cutting and making good the floor & wall wherever requiredcomplete in all respects 100 x 100 mm outlet |
| 80 | Providing & fixing (PP) inlet fitting with one or more inlets fabricated from 110 mm outer dia (PP) pipe and solvent welded sockets and fixed to (PP) Trap and set in cement concrete as per drawing complete |
| 81 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources |
| 82 | Providing, fixing and testing of reducing floor drain of 110x63 mm OD as floor drain in cement concrete 1 : 2 : 4 float with floor complete in all respects as directed by Engineer-incharge complete as per standard design. |
| 83 | Providing and fixing 125 mm dia, 1 mm thick CP grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete in all respects as directed by Engineer-incharge complete as per standard design. 125 mm dia |
| 84 | Providing and fixing in position 125x125 mm square / 125 mm dia stainless steel cockroch trap consisting of 0.45 mm thick inner and outer cup and 1.0 mm thick top grating (Jali) with ring to be fixed inside uPVC ‘P’ traps with cement concrete. (for kitchen and pantry) |
| 85 | Providing, fixing, jointing and testing of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) including injection moulded fittings with bosses like tees, bends, access door bends, single/double 'Y' , crosses, reducers, end caps, cowl etc. with or without access doors jointed with approved solvent cement as per manufacturer's recommendations, including under floor or fixed to walls and ceilings with Hilti powder coated pipe support channel, clamp with EPDM rubber, rod/hardness, fastner, nuts, bolts etc. as per manufacturer's recommendations complete including cutting and making good the floors and walls where required complete in all respects as directed by Engineer-incharge complete as per standard design. 110 mm |
| 86 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c trenching .refilling & testing of joints complete as per direction of Engineer in Charge. (Internal work exposed on wall). PN - 16 Pipe, 32mm OD (SDR-7.4) |
| 87 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c trenching .refilling & testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.). PN - 16 Pipe, 20mm OD (SDR-7.4) |
| 88 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c trenching .refilling & testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.). PN - 16 Pipe, 25mm OD (SDR-7.4) |
| 89 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c trenching .refilling & testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.). PN - 16 Pipe, 32mm OD (SDR-7.4) |
| 90 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c trenching .refilling & testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.). PN - 16 Pipe, 50mm OD (SDR-7.4) |
| 91 | Providing & fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape, rockwool 6 inch per side wire mesh , polyethlene tapping with cello tape aluminium sheet 26 gauge cladding with dia complete job including carriage. 19mm thick 50mm dia (OD) PPR 20mm |
| 92 | Providing & fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape, rockwool 6 inch per side wire mesh , polyethlene tapping with cello tape aluminium sheet 26 gauge cladding with dia complete job including carriage.19mm thick 50mm dia (OD) PPR 20mm |
| 93 | Providing & fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape for inner wall fittings, complete job including carriage, 19mm thick 50mm dia (OD) PPR 25mm |
| 94 | Providing & fixing heat tape 33 watt on PPR pipes made of denforced or chromelox or equivalent make , as approved by engineer in charge , complete job |
| 95 | Providing and fixing ball valve (brass) of approved quality complete : High or low pressure with plastic floats: 20 mm nominal bore |
| 96 | Providing and fixing ball valve (brass) of approved quality complete : High or low pressure with plastic floats: 32 mm nominal bore |
| 97 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50 mm dia |
| 98 | Providing and fixing motorised valve (with by pass line including ball valve) with float type sensors suitable for 240 volts with working pressure rating of not less than 5 kg/cm2 with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including necessary cables, conduits, upto junction box, pipe, butter fly/ball valves, flanges, union, nutbolt etc., complete in all respects as directed by Engineer-incharge complete as per standard design. 32 mm dia |
| 99 | Providing and fixing brass single acting air valve PN 1.6 of approved quality with bolts, nuts, rubber insertion, tail pieces, tapers etc. if required complete in all respects as directed by Engineer-incharge complete as per standard design. 25 mm dia |
| 100 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources |
| 101 | Providing and fixing of material for the insulation of Water Storage Tank of with nitrile sheet, taping with cello tape , Rockwool 6 inch per side , wire mesh, polythene, aluminium sheet 26 gauge cladding with dia of , complete job 19mm thick nitrile sheet. |
| 102 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 103 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All Kind of Soil Pipes cables etc exceeding 80 mm dia but not exceeding 300 mm dia. |
| 104 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :200 mm diameter |
| 105 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 106 | Providing and fixing square-mouth S.W. gully trap grade ‘A” complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :150 x 100 mm size P type.With cement blocks |
| 107 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With Solid Blocks |
| 108 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as perstandard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 109 | Extra for depth for manholes Size 120x90 cm With Solid Blocks |
| 110 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kind of soil Pipes cables etc exceeding 80 mm dia but not exceeding 300 mm dia. |
| 111 | Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. 450 mm dia. |
| 112 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 113 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With Solid Blocks |
| 114 | Extra for depth beyond 45 cm of brick masonry chamber : For 455x610 mm sizeWith Solid Blocks |
| 115 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as perstandard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 116 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kind of soil Pipes cables etc exceeding 80 mm dia but not exceeding 300 mm dia. |
| 117 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c trenching .refilling & testing of joints complete as per direction of Engineer in Charge. (External work) PN - 16 Pipe, 32 mm OD (SDR-7.4) |
| 118 | Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) necessary excavation7foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : With Solid Blocks |
| 119 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25mm |
| 120 | Supplying and fixing of GI Concealed Box for Electrical Switches | Galvanized Iron Flush Mount Switch Box | Heavy Duty Rust-Resistant Wall Box Houses light points, fan points, or junctions in RCC Slab all complete job Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender