Tender For Special Repair To Building Nos. Tb-03, Guest Room, Sp-18 And Ha-218 At Different Locations Of Bagrakote Mil Stn Under Ge Sevoke Road
Tender Value
48.40 Lakhs
Estimated cost
Bid Submission
02 Sep 2026
17 days left
EMD
96800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kalimpong → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Building Nos. Tb-03, Guest Room, Sp-18 And Ha-218 At Different Locations Of Bagrakote Mil Stn Under Ge Sevoke Road
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed. |
| 2 | Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed |
| 3 | Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed |
| 4 | Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided for, removing rubbish off the premises etc complete all as specified and directed. |
| 5 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each, complete all as specified and directed. |
| 6 | Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each, complete all as specified and directed. |
| 7 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and as directed. |
| 8 | Demolition of brickwork built in cement mortar and removing rubbish off the premises etc complete all as specified and directed |
| 9 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 10 | Dismantling timber scantlings 40 sq. cm and over in section, in any position, complete all as specified and directed. |
| 11 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and directed. |
| 12 | Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris as directed including necessary scaffoldings etc complete all as specified and directed |
| 13 | Taking up or down 15 mm bore steel water tubing and connections complete all as specified. |
| 14 | Taking up or down 20 mm bore steel water tubing and connections complete all as specified. |
| 15 | Taking up or down 25 mm bore steel water tubing and connections complete all as specified. |
| 16 | Dismantling PVC/HDPE/plastic water tank of capacity Exc 500 Litre and not Exceeding 1000 Ltr complete all as specified and directed |
| 17 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded pointed in any mortar and removing rubbish off the premises etc complete all as specified and directed |
| 18 | Surface dressing not exceeding 15 cm deep in soft/loose soil and site clearence complete all as specified and as directed. |
| 19 | Excavating in post holes (or similar holes) each n exc 0.50 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplus soil to a distance not exc 50 m and making good surfaces in soft/loose soil complete all as specified and as directed. |
| 20 | Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 21 | All as per Item No.20 above but in hard/dense soil. |
| 22 | Excavation over areas not exc 1.5 m in deep and getting out in hard/dense soil complete all as specified and directed. |
| 23 | All as per Item No.22 above but exc 1.5 m and not exc 3 m in deep and getting out in hard/dense soil complete all as specified and directed. |
| 24 | Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. |
| 25 | Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed. |
| 26 | Materials and Labour for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface. |
| 27 | Materials and Labour for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed. |
| 28 | Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. |
| 29 | Materials and Labour for plain cement concrete (1:2:4) type B-0, using 12.5mm graded stone aggregate as in coping, kerb and the like including necessary formwork complete all as specified and as directed. |
| 30 | Materials and Labour for plain cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate as in holdfast block, filling of MS chowkats and the like including necessary formwork complete all as specified and as directed. |
| 31 | Materials and Labour for plain cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate as in surface channel and drain including necessary formwork complete all as specified and as directed. |
| 32 | Materials and Labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. all as specified and as directed. |
| 33 | Materials and Labour for formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similer works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed |
| 34 | Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, cantilevers, lintels, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed |
| 35 | Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in slabs and shelves supported on walls, beams and columns in floors, roofs and landings etc, any thickness complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately) |
| 36 | Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed . (Note: Steel reinforcement shall be measured & paid separately) |
| 37 | Materials and Labour for precast reinforced cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc, any thickness, placed in position and set in cement mortar 1:4 complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately) |
| 38 | Materials and Labour for precast cement concrete louvers and jallies,(1:2:4) type B0 using 12.5 mm graded stone aggregate, 25mm thick (measured solid), including all mouldings, Set in cement mortar (1:4) complete all as specified and directed. |
| 39 | Materials and Labour for TMT bars 6 to 8 mm dia , as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 40 | Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 41 | Materials and Labour for TMT bars 6 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 42 | Materials and Labour for 6 to 8 mm dia TMT bars as in reinforcement for half brick thick walls, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 43 | Materials and Labour for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E- 250) quality-A/Fe.290.Gde-E-165 including painted one shop coat of zinc chromate primer paint (including preparation of surface) at workshop before fabrication complete all as specified and as directed. |
| 44 | Materials and Labour for Steel work in tubular trusses including posts,purlins, rafters, special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 |
| 45 | Supply & fixing Mild steel screw bolt (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be filled with washers and one hexagonal or square nut 5 to 10mm dia shank and exc 5cm but n exc 10cm long complete all as specified and as directed. |
| 46 | Supply & fixing rolled mild steel Flats , channel, angle or tee sections as in wind ties for roof including securing bolts, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 47 | Supply & fixing rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 290 Gde-E 165) complete all as specified and as directed. |
| 48 | Supply & fixing Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165. |
| 49 | Supply & fixing mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed. |
| 50 | Supply & fixing 0.56mm thick plain, aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (as in crumple joint) complete all as specified and as directed. |
| 51 | Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 52 | Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed. |
| 53 | Materials and labour for preparing of new wooden surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 54 | Materials and labour for preparing of previously primed steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed. |
| 55 | Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 56 | Materials and labour for preparing of new steel surfaces of any description , below 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 57 | Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed. |
| 58 | Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,on vertical surfaces such as skirting,dado and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 10mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed. |
| 59 | Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed. |
| 60 | Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,on vertical surfaces such as skirting,dado and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 10mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed. |
| 61 | Materials and labour for coloured 450x350x7-8 mm /350x250x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed. |
| 62 | Materials and labour for Vitrified Ceramic tiles of dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 20 mm th screed bed in CM 1:6 complete all as specified and as directed. |
| 63 | Materials and labour for Vitrified Ceramic tiles of dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in vertical serfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed. |
| 64 | Materials and labour for Kota stone slab 20-25mm thick in riser of steps,skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:4) including rubbing and polishing complete. |
| 65 | Materials and labour for Kota stone slab 20-25mm thick in floor laid over and including 20mm thick screed bed or bedding layer of cement mortar (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. |
| 66 | Materials and labour for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand Complete all as specified and as directed |
| 67 | Materials and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed |
| 68 | Materials and labour for providing heavy duty Vitrified Ceramic tiles 300x300x10 mm thick, polished, premium quality of colour as approved, in floors, paths, hardstanding etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed. |
| 69 | Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in floors, plinth protection, path etc. finished the surface of concrete even and smooth without using extra cement, complete all as specified and directed. |
| 70 | Materials and labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in sub-base of floors etc. finished the surface of concrete even and rough , complete all as specified and directed. |
| 71 | Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in sub-base of floors etc. finished the surface of concrete even and rough , complete all as specified and directed. |
| 72 | Materials and labour for 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggt as in sub bases of floor finished even and rough, complete all as specified and directed. |
| 73 | Materials and labour for brick work with fly ash bricks modular size, straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 74 | Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 75 | Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:4 complete all as specified and as directed. |
| 76 | Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed. |
| 77 | Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in one and half brick thick honey comb walls built in cement mortar 1:4 complete all as specified and as directed. |
| 78 | Materials and labour for broken brick bats to fill in soakage well complete all as specified and as directed. |
| 79 | Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed. |
| 80 | Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. |
| 81 | Supply and fixing 105 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings lock strike plate etc complete all as specified. |
| 82 | Supply and fixing 165 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified. |
| 83 | Supply and fixing flush shutters 40mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 84 | Supply and fixing flush shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 85 | Supply and fixing 35mm thick second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, complete all as specified and directed. |
| 86 | Supply and fixing factory Made Solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site, with particle board core as per specification & drawing complete all as specified and directed. |
| 87 | Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators and partitions with one or morerebates including joining cleat for fixing etc. complete all as specified and as directed. |
| 88 | Materials and labour for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standardtubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessaryfilling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleatangle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws. complete all as specified and directed |
| 89 | Supply and fixing Anodised aluminum grill (anodised tansparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern., with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and derection of Engineer-in-charge. |
| 90 | Supply and fixing stainless steel butt hinges, 100 mm size , complete all as specified and directed. |
| 91 | Supply and fixing Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200 mm , complete all as specified and directed. |
| 92 | Supply and fixing Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 300 mm , complete all as specified and directed. |
| 93 | Supply and fixing Mild steel pressed handles, oval type, stove enamelled black, 150 mm size, complete all as specified and directed. |
| 94 | Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 125 mm long, complete all as specified and directed. |
| 95 | Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed. |
| 96 | Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 200 mm long, complete all as specified and directed. |
| 97 | Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed. |
| 98 | Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 125 mm size , complete all as specified and directed. |
| 99 | Supply and fixing for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed. |
| 100 | Supply and fixing 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and as directed. |
| 101 | Supply and fixing mild steel stove enamelled black 300mm long ordinary rat tail rod pattern spring fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and directed. |
| 102 | Supply and fixing mild steel Mortice lock, vertical type, size100 mm with 4 levers with two keys complete all as specified and directed |
| 103 | Supply and fixing Steel rolling shutters, thickness of laths1.25 mm, with out ball bearing, including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, push pull or manual type including taking out old unserviceable rolling shutter complete all as specified and directed |
| 104 | Supply and fixing Safety lever locks mild steel with 4 levers for rolling shutter complete all as specified and directed |
| 105 | Supply and fixing ball bearing for rolling shutter complete all as specified and directed |
| 106 | Supply and fixing CP curtain rails 20 mm dia chromium plated, with and including fixing brackets, stops, rollers etc, complete al as specified and directed. |
| 107 | Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete with glazing bars, dovetailed or welded complete all as specified and directed. |
| 108 | Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete without glazing bars, dovetailed or welded complete all as specified and directed. |
| 109 | Supply and fixing steel ventilators with top hung shutter including hinges,steel peg stay, including one shop coat of Zinc Chrome primer complete all as specified and directed. |
| 110 | Supply and fixing Mild Steel Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete as specified and directed. |
| 111 | Supply and fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed. |
| 112 | Supply and fixing 4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed. |
| 113 | Supply and fixing 4.8 mm thick sheet glass, ordinary quality and glazing with beading , to be fixed with aluminium frames complete all as specified and directed. |
| 114 | Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 115 | Materials and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 116 | Materials and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 117 | Materials and labour for rendering 20mm thick in two layers of 10 mm thick each in cement mortar (1:4) on fair faces of brick work or concrete surfaces,WPC shall be mixed with morter of top layer, finished even and fair, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only) |
| 118 | Supply only liquid Water Proofing Compound of approved make. |
| 119 | Materials and labour for applying three coats of white wash on new wall surface including preparation of surface, complete all as specified and directed. |
| 120 | Materials and labour for preparation of new plastered surfaces of walls and applying two coats of cement based paint over chalk whitening on wall complete all specified and directed. |
| 121 | Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over chalk whitening on wall complete all specified and directed. |
| 122 | Materials and labour for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer on wall complete all specified and directed. |
| 123 | Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer on wall complete all specified and directed. |
| 124 | Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing 4mm thick Decorative non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm or higher) |
| 125 | Materials and labour for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section(not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. |
| 126 | Providing and fixing Gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed. |
| 127 | Materials and labour for preparation of gypsum ceiling surfaces and applying 2-3mm thick wall care putty of approved make complete all as specified and directed. |
| 128 | Materials and labour for preparation of new ceiling surfaces and applying two coats of oil bound distemper of approved colour with roller over chalk whitening after preparation of surface complete all as specified and directed. Please Enable Macros to View BoQ information |
| 129 | Materials and labour for preparation of new ceiling surfaces and applying two coats of oil bound distemper of approved colour with roller over chalk whitening after preparation of surface complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysSep 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender