Tender For Renovation Of Vc Office, Vc Office Ancillary Room And Washroom Of The Kashmere Gate C Us Of Dr.B.R.Ambedkar University Delhi
Tender Value
2.91 Lakhs
Estimated cost
Bid Submission
27 Aug 2026
12 days left
EMD
5900
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Vc Office, Vc Office Ancillary Room And Washroom Of The Kashmere Gate C Us Of Dr.B.R.Ambedkar University Delhi
BOQ
| Sl. No. | Item Description |
| 1 | CIVIL: |
| 2 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 3 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 4 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats |
| 5 | Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge :Using rough Kota stone |
| 6 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. |
| 7 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes |
| 8 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) |
| 9 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead |
| 10 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge |
| 11 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 12 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15mm nominal bore |
| 13 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour : 15 mm nominal bore with 45 cm length |
| 14 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour : 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 15 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour : Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms |
| 16 | Disposal of moorum/ building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-Charge |
| 17 | Providing and fixing internal wall panels on Light gauge steel frame work with 12 mm thick HDMR board fixed on 8mm thick HDMR board as per standard sizes fixed with self-drilling / tapingscrews / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately) as per the direction of Engineer-in- charge. |
| 18 | Painting with nitrocellulose based paint (automotive) on wood work in required color/wooden shade texture with following process in the sequence as detailed below : 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applyiong two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade oil putty (filler) to fill the small and big holes/grroves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs 4. On this, 1st coat of paint is applied with spray gun using thinner in required proportion. This 1st coat is allowed to dry fro 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final paint is applied with compressor pressure spray gun using thinner mixed in required proportion complete as per Direction of Engineer- in- charge. ( Final coat to be done in 1 or 2 layers without gap of time ). |
| 19 | Providing and fixing CP Brass two way bib cock of 15 mm nominal bore with all necessary fixtures, fittings, accessories, and connections, complete in all respects as approved by Engineer in charge |
| 20 | Providing and fixing CP Brass Pillar Cock mixer of 15 mm nominal bore with all necessary fixtures, fittings, accessories, and connections, complete in all respects as approved by Engineer in charge |
| 21 | Provision for covering of existing furniture and floor wth plastic sheet and taking out after the completion of the work including its disposal along with the shifting of furniture within the campus etc complete as per the direction. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender