Tender For Furnishing Of Extended Wing & Refurbishment Of Existing Wing Of Heavy Water Board At 5Th Floor Of Vs Bhavan, Anushaktinagar, Mumbai
Tender Value
2.48 Crore
Estimated cost
Bid Submission
17 Sep 2026
2 days left
EMD
4.97 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mumbai Suburban → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Furnishing Of Extended Wing & Refurbishment Of Existing Wing Of Heavy Water Board At 5Th Floor Of Vs Bhavan, Anushaktinagar, Mumbai
BOQ
| Sl. No. | Item Description |
| 1 | Customized CE's Table with back unit & side credenzaSupplying and intallation of Table fully finished in Veneer on all outer surfaces as per design and top to be of 12mm thick corian along with side credenza on one side.Design Description:a) Main Table (3000mmx900mmx750mm):• Main Table fully finished in Veneer (4 mm thick) on all outer surfaces as per design and top to be of 12mm thick corian supported on one side with side credenza & other side on 40 mm/38mm thick marine plywood.• Main Table top in shape of Rectangular / Arch is to be finished in corian pasted on 36mm thk. marine ply structure equipped with a rectangular leather desk blotter installed in the center of the table and aligned towards working edge of the table. Edge of the table to be 36mm thick +12 mm corian top being extended for edge banding and all corners bevelled with radius of 8mm. • Table to be supported on one side Credenza at same level finished with Veneer above, other side will have one Veneer panel leg of 50 mm thick tapered on edges covering the entire width. Long span will be further strengthened by intermediate supports running across the width partially. Other details shall be as per technica specifications & drawings.b) Side credenza (1000x900x750mm)• Side credenza positioned on one side of the table supporting the table. Credenza fully finished with Veneer pasted on 18mm marine ply equipped with 1 drawer and an open shelf in one column and 2 shutters (inside shelf adjustable) positioned beside the working table. All drawers and shutters detailed with 2 finger grooves 25mm broad with a tapered drawer facia top edge. Drawer internals to be finished with 1 mm thick Leather Veneer. Drawers shall be equipped with soft close Quadro channel.c) Cabin storage detail (Back unit of size:4000 width x500mm depth x2400 height)• Providing, assembling &installation of custom made Back Unit complimenting executive table 1 of size 4000 mm width x 500 mm Depth x 2400 mm height as per technical specifications, drawing/reference figures, theme & as directed by Engineer In Charge.Note: Refer Technical specifications for details |
| 2 | CE's briefing room tableProviding, fabricating, transporting & installation of 10-12 seater Conference table of size 3000Wx1150Dx750H consisting of :• Work top-Made of 40mm Thick Pre-laminated twin board(Particle board with both side lamination) or or equivalent board of approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. The top layer shall be corian of 12 to 15mm thickness bonded over pre laminated twin board with bull nose edges.• Access panels provided with soft closing hinges. • Understructure-The Under-structure consists of combination of 25mm and 18mm Pre-laminated twin board and approved shade conforming to IS-12823:1990 or equivalent board , Edge banded with matching 2 mm thick PVC lipping. • Anodized aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. • Wire Management-Bottom cabinet with door shall be provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 modules Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg. HDMI, VGA-A, etc). Size - 3000Wx1150Dx750H |
| 3 | Grandeur Main Table 3000WX1050D, ERU - 1500W X 600DProviding, assembling, transporting and Placing / Fixing Main table of size 3000 Wx1050Dx750H with attached ERU 1500Wx600Dx610H specification consist of : Main Worktop: Made of 43mm Thick (±1) combination of MDF and particle board with top veneer face coated with clear lacquer. All edges are edge banded with matching 1mm thick veneer lipping. Leather Pad: Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface. This leather pad is fixed to main top panel. Drawer Unit: Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination of MDF and particle board with top veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping. Remaining construction is of 18mm pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with leatherette on top surface. Drawer unit is provided with soft closing channels for smooth opening and closing. Drawer unit is secured with side central lock. OPEN STORAGE UNIT: Top panel and open storage unit modesty panel is made of 43mm Thick (±1) Combination of MDF and particle board with top veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping. Remaining construction is of 18mm pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade)Product should be certified by a NABCB Accredited agency for conformity assessment Note: Refer Technical specifications for details |
| 4 | VC collage tableProviding, assembling, transporting & installation of High seating Video Conference table of size 2100W X 1200D X 1920 H consisting of:• Frame Material - Particle Board Table Top Material Membrane, • Wire management • Display - Not Included here • Video Conference kit - The system shall facilitate engaging team conversations with audio video configuration. Concealed Audio - Video cabling shall be provided accordingly. Optimum Space & View Angle Table shall be designed considering viewing angle of each user and comfortable space to user. Power Connectivity: Video Table shall be equipped with provision for power connectivity module with ease of access including Popo up box for IO ports/ HDMI ports/ Power socket , switches, USB type A 7 C. • Colour Nova Magnolia + Noce Versailles or of shades approved by the Engineer in Charge. Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 5 | Finesse Main Table 1650W X 750DProviding, assembling, transporting & installation of rectangular sitting desk of size 1650 Width mm x 900 Depth mm x 750 Height mm consisting of :• Table top made out of 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl). Flat edge duly sealed with 2 mm thick PVC beading. • Modesty shall be 18 mm thick plain particle board () PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading.Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade) Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 6 | Finesse Main Table 1200W X 600DProviding, assembling, transporting & installation of Office Table - size 1200 Width mm x 600 Depth mm x 750 Height mm , consiting of : • Table top made out of 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl). Table flat edge duly sealed with 2 mm thick PVC beading. •Modesty shall be of 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade) Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 7 | Open storage units as per drawing & technical specificationsSupplying and placing of Freestanding storage with openable swing door shutters. Storage Unit of 450 mm thick shall be provided with shutters made out of 18mm marine ply with thick 4mm thick veneer finished and back in 12 mm thick marine ply. The top, door and shelf are with 6mm matching wooden beading & inside will be 1mm thick fabric finish lamiante. Indluding all the brass hardware and Hinges. Mellamine polish to the veneer or PU finish on mdf is as per the design.Typical size - 1300L x450WX2400MMHTNote: Only front surface area shall be measured for the payment purpose. |
| 8 | Back Unit (Full height storage as per drawing & technical specifications)Supplying and placing of Freestanding storage with openable swing door shutters of width 450mm. Storage Unit shall be provided with shutters made out of 18mm marine ply with thick 4mm thick veneer finished and back in 12 mm thick marine ply. The top, door and shelf are with 6mm matching wooden beading & inside will be 1mm thick fabric finish lamiante. Indluding all the brass hardware and Hinges. Mellamine polish to the veneer or PU finish on mdf is as per the design.Typical size - 1800Lx450WX2400H MMNote: Only front surface area shall be measured for the payment purpose. |
| 9 | Renovating Back UnitRenovating existing storage unit of size 2.1m (H) x 1.2m(L)x 0.4m (D)by providing internal lining with marine ply board toughened glasss shuuters & toughened glass shelves at top portion & bottom portion consisting of with 12 mm thick marine shutters and finsihed with 4 mm thick veneer with final coating with PU paint.Internal lining shall be made with 8 mm thick marine ply board (Side, top & bottom panel ) with matching laminate & PVC Edge banding as approved by EICa)Top portion (1.5m x 1.2m )Shutters: 8 mm thick frameless toughened glass door shutters in two panels as per drawing including providing & fixing top & bottom pivot type (GH -GS) of approved finish (golden) fixing arrangement with necessary hardwares/ acessories including making holes for fixing door fittings, with lock & key arrangement at bottom etc. all complete as per direction of Engineer incharge.Glass shelves: Made up of 12mm thick toughened glass including fixing arrangement with SS glass holder & removable as per requirement.b) Bottom Portion (0.6m x 1.2m)Shutter: Shutter shall be made with 12 mm thick marine ply with laminate of 1 mm thickness on inside & finished with PU coating on venner of 3mm thickness on visible side. Venee & laminate shall complements the table as directeed by EIC. Shutter shall be provided with all acessories, locks, handles, hinges of approved make as directed by EIC.Shelves: Shleves shall be 20 mm thick with partition at the centre of same thickness, all finsghed with 1 mm thick laminate.Edgebanding : 2 mm thick PVC edgebanding of matching shade.The bifurcation of glass & wooden portoon at top & bottom shall be done with 25mm thick Marine ply finished in veneer & extebnding beyond the glass shutter to support designed wooden vertical post of 04'' diameter extending to the top panel. All external visible sufave to be finished with venner & PU paint.Cost quoted shall include removing existing cupboard, shelves, shutters all complete & making surface smooth & finished by cement mortal (1:4) & placingg at a designarted place for onward transportation to nearby municipal yard.Note: Only front surface shall be measured for the payment purpose. |
| 10 | Free standing storage as per drawing & technical specificationsSupplying and placing of 450mm width Freestanding storage with openable swing door shutters. Storage Unit shall be provided with shutters made out of 18mm thick prelaminated particle board and back in 9mm thick prelaminated particle board.The top, door and shelf are with 2mm PVC egde Imported banding & other panels are with 0.8mm thick PVC Imported edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. Indluding all the hardware and Hinges.The Laminate is Low pressure laminate also know as melamine in E1 grade LPL board. The LPL is complied with IS 12823:1990 (Wood products - prelaminated particle boards specification). It covers major LPL performance such as scratch resistance, wear resistance, stain resistance with inclusion of Formaldehyde test meeting E1 standards. (Typical size - 1200Lx450WX1050H MM)Note: Only front surface area shall be measured for the payment purpose. |
| 11 | 3 drawer free standing storageProviding, assembling, transporting & placing / fixing in position, 3 drawer Pedestal consisting of : • Free-standing pedestal flat metal front of size 390W x 435D x 646H, 1DR = 1 Box + 1 File, Central Locking. 3 drawer pedestal unit (box + box + file) to be made out 0.8mm thick CRCA steel for body shell, drawer tray, front & rear side stiffener. • Top & bottom stiffener shall be of 1.2mm thick. • All slides with double extension precision ball slide. • Drawers to be without handles for clean finish. For drawer pulling, side wise tapered recess provided in shell behind drawer fronts.• 10 lever cam lock & central locking with actuator & lock channel mechanism. • Metal finish to be in epoxy polyester power coated with 40 to 50 microns. • Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade)• Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 12 | Storage for PANTRY AreaProviding storage cabinet of approximate size 3.0mx1.2mx0.6m, made up of cement fiber board confirming to IS 14862 or cement bonded particle board conforming to IS 14276 as per approved drawing and as detailed below: Back & Side panel - 25mm thick plain cement boards fixing using necessary screws, clamps etc. Board front side visible edge shall be provided with powder coated aluminium U channel lipping suitable for 25mm board, fixed with silicon sealant. Shutters - Shutters configuration as per drawings. Shutters made out of 12 mm thick prelaminated cement board (both side laminated) with powder coated aluminium U channel lipping of approved size and thickness suitable for 12mm board, alround, fixed with silicon sealant. Shelve: 20mm thick plain cement board. Accessories: SS Hinges of approved design & Make of Godrej or equivalant as per requirement & as approved by EIC , concealed or approved type SS door handles one for each shutter, suitable lock of godrej, with all acessories of approved design and make approved by EIC. Prelaminated Cement boards shall be used of approved shade with all fixtures and fittings, materials, labour, transport complete. as per specifications and stoarge unit to be provided below working top for storage or as directed by EIC. Note: Face area only shall be measured for payment. Rate shall be all clusive price per unit area for all the jobs as per BOQ. |
| 13 | Optimizer plus power driveProviding, assembling, transporting & installation of compactor consisting of :• Storage units –fixed and movable – rigidly mounted on an Understructure which rolls on Extrusion channels with connected platform. • CONFIGURATIONS: Optimizer POWERDRIVE type – 2 Bay TYPE- M2 (DMX Drg-DOS218135) (Bay denotes side by side unit placements in a block) each of above configurations can have following type of blocks – 1. Static Drive (SD) 2. Last Drive (LD) 3. Twin Drive (TD) – 2 body back-to-back. (Note: Unless otherwise specified, all dimensions are in mm & represent nominal value) MAIN BODY: (a) Construction: Rigid Knock Down construction made of 0.8 thick CRCA Steel conforming to IS: 513 Grade. Each body block consists of 1 Main unit & then Add-on units (1, 2, and 3 depending on no. of bays 2, 3, 4 respectively). Each unit has 5 loading levels formed by 4 nos. adjustable shelves for 1980 Height body and 6 loading levels with 5 nos. adjustable shelves for 2361 Height body. Body units are mounted on an understructure which is fixed or moving. 1. Front Cover: It is the foremost panel of the body on which POWERDRIVE cover with front electronics panels are fixed. It is made of 0.8 thick. CRCA Steel conforming to IS: 513 Grade. 2. Back Cover: It is the backmost panel of the body and is the mirror image of the front cover. It is made of 0.8 thick. CRCA Steel conforming to IS: 513 Grade. The back cover has a rubber extrusion to avoid bump into two bodies. 3. Back Panel: The back panels are made of 0.6 thick. CRCA Steel conforming to IS: 513 Grade. There are two back panels – Top back panel and Bottom back panel for 1980H unit as well as 2361H unit. The two back panels are fixed together using machine screws. The purpose of the back panel is to act as a divider between 2 opposite shelves in twin body (TM/TD). When the entire optimizer layout is locked it also prevents access to inside files from the outside in case of single body (SS/SD/SL/LD). 4. Shared Panel: The shared panel acts as a partition between two adjacent bodies. It is made of 0.8 thick. CRCA Steel conforming to IS: 513 Grade. 5. Door Frame: The door frame assembly is made of 2 vertical door stiffeners, a top horizontal stiffener, and a bottom horizontal stiffener. In case of LD/SD, it provides rigidity to the entire body as the topmost shelf is pop riveted with the back panel as well as both the vertical door frame. In case of TD, it provides rigidity to the entire body as the two topmost shelfs of two bodies is bolted as well as both the vertical door frame of two bodies is pop riveted with its topmost shelf. The door frame is also useful if the customer chooses to have doors for the optimizer as the doors are hinged about the door frame. It is made of 0.8 thick. CRCA Steel conforming to IS: 513 Grade. All components shall be as per technical specifications |
| 14 | VSDU(12) 1200 X 450 X 1192Providing, assembling, transporting & installation of Storage specification consisting of Overall Dimensions 1200mm (W) x 450mm (D) x 1192.5mm (H). The top shall be wooden top PLB (25 mm add in unit height). The Rigid Knock Down Construction, Back, Sides and Door shall be made from 0.7 mm high yield strength CRCA, rest in 0.8 mm CRCA. CRCA - 'D' Grade as per IS-513. Sliding door arrangement shall have sliding door with top hanging arrangement to prevent derailment. Each door shall be provided with 2 plastic rollers having steel ball bearing for smooth movement of door & less noise. Locking shall be 5 lever cam lock for safe locking. Handle shall be plastic flush & recessed handle. Shelving shall have Height wise adjustable shelf mounting. Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum. Shall have 4 no. of adjustable half shelves. Accessories optional shall be cradle with pipes for hanging files. Leveler shall be screwing type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns. A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm. Product should be certified by a NABCB Accredited agency for conformity assessment . |
| 15 | Majesta 3 seater sofaProviding, assembling, transporting & installation of Pure Leather Three Seates Sofa set of size 2050W x 840D x 760H, Sofa consisting of • Seats : 3-Seater lounge seating made of soft foam of density 28 kg/m3 with enhanced comfort and cushioning. Upholstery - with Pure Leather Upholstery - Pigmented: Durable and ergonomically perfect for seating. The top grains of leather are clearly visible which adds to the aesthetics.• Spring Webbing: Provides bouncing back action for floating feeling. Construction: Made of solid wood frame with ply cross section which is moisture, termite and borer resistant. Adequate treatment of wood initiated to enhance longevity and maintain robustness.• Ground Elevation: Equipped with legs, the sofa is elevated to allow a level of ground clearance for easy cleaning and maintenance etc. complete as perSpecifications, Architectural drawing and as direcetd by the Engineer in charge. Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade) Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 16 | Majesta 2 seater sofa Providing, assembling, transporting & installation of Pure Leather Two Seate Sofa set of size 1520W x 840D x 760H consisting of: Seat : The seat is made of soft foam of density 28 kg/m3 with enhanced comfort and cushioning. Upholstery - with Pure Leather Upholstery - Pigmented: Durable and ergonomically perfect for seating. The top grains of leather are clearly visible which adds to the aesthetics.Spring Webbing: Provides bouncing back action for floating feeling. Construction: Made of solid wood frame with ply cross section which is moisture, termite and borer resistant. Adequate treatment of wood initiated to enhance longevity and maintain robustness.Ground Elevation: Equipped with legs, the sofa is elevated to allow a level of ground clearance for easy cleaning and maintenance etc. complete as perSpecifications, Architectural drawing and as direcetd by the Engineer in charge. Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade) Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 17 | 3 seater sofa (Type I)Providing, assembling & placing in position visitor lounge sofa (SIZE - 750D x 1500L (MM)) - The under structure shall be made of 12 mm thick hot pressed moisture resistance & termite proof plywood as per IS: 303. The structure shall be covered with 3 mm thick MDF sheet to provide a backing surface for foam padding. The top structure of pouf i.e. seating surfaces shall be provided with slab foam of 32kg/m3 on the top for soft feel while the sides of top structure shall be covered with PU foam of 28 kg/m3 density all around. The bottom structure has 6mm PU foam of 60kg/m3 density on all four vertical sides to give a soft touch and feel. The pouf shall consists of 2 separate upholstered stitched covers made up (fort structure) & 230 to 250 mm GSM polyester fabric (for bottom) complete as per direction of Engineer - in- charge. |
| 18 | 3 seater sofa (Type II)Providing, assembling & placing in position visitor lounge sofa (SIZE - 750D x 11950L (MM)) - The under structure shall be made of 12 mm thick hot pressed moisture resistance & termite proof plywood as per IS: 303. The structure shall be covered with 3 mm thick MDF sheet to provide a backing surface for foam padding. The top structure of pouf i.e. seating surfaces shall be provided with slab foam of 32kg/m3 on the top for soft feel while the sides of top structure shall be covered with PU foam of 28 kg/m3 density all around. The bottom structure has 6mm PU foam of 60kg/m3 density on all four vertical sides to give a soft touch and feel. The pouf shall consists of 2 separate upholstered stitched covers made up (fort structure) & 230 to 250 mm GSM polyester fabric (for bottom) complete as per direction of Engineer - in- charge. |
| 19 | Sofa without armrest. (SIZE - 600D x 600L (MM))Providing, assembling & placing in position visitor lounge sofa - The under structure shall be made of 12 mm thick hot pressed moisture resistance & termite proof plywood as per IS: 303. The structure shall be covered with 3 mm thick MDF sheet to provide a backing surface for foam padding. The top structure of pouf i.e. seating surfaces shall be provided with slab foam of 32kg/m3 on the top for soft feel while the sides of top structure shall be covered with PU foam of 28 kg/m3 density all around. The bottom structure has 6mm PU foam of 60kg/m3 density on all four vertical sides to give a soft touch and feel. The pouf shall consists of 2 separate upholstered stitched covers made up (fort structure) & 230 to 250 mm GSM polyester fabric (for bottom) complete as per direction of Engineer - in- charge. |
| 20 | Posture Perfect High Back chairProviding, assembling, transporting & installation of High Back console consisting of:SEAT/BACK ASSEMBLY SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide. Upholstered seat sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W) BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection moulded Plastic Inner. HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D), ARMRESTS: The armrest having four range of adjustment. Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all other Adjustment are provided in adjustable arm top sub assembly.• Up-Down adjustment has 8 position (10.5±0.5cm range) • Arm top swivel adjustment- 2 position, 12°±2° swivel inside • Arm top width adjustment - Any position (2.0±0.5cm range each arm top) • Arm top To - Fro Adjustment- any position (4.0±0.5cm range) • Armrest top is made up of high density PU moulded over glass filled Poly-amide inner. POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following Features: • 360° revolving type. • Forward tilt of seat and back. Upright tilt lock. Tilt tension adjustment can be operated in seating position. 3-position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated with the mechanism with help of Polypropylene Seat cover. Seat Depth can be adjusted in sitting position. Seat depth adjustment range is of 5.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die cast aluminums Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position. It can be adjusted in the range of 7.5±0.5 cm. PNEUMATIC HEIGHT ADJUSTMENT: The heavy-duty class 4 pneumatic height Adjustment has an adjustment stroke of 13.0±0.3 cm PEDESTAL: The pedestal is made of die-cast aluminum with buffing finish. It is fitted with 5 nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection molded in Poly-amide with PU lining, having 6.5±0.1cm wheel Diameter and assembled to pedestal. Product should be certified by a NABCB Accredited agency for conformity assessment . |
| 21 | Thrill executive high back chairProviding, assembling, transporting & installation of High Back Chair specification consisting of Seat/Back Assembly – The back is made up of 1.2+-0.1cm. thick hot-pressed plywood & seat is made up of 1.5+-00.1cm. thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric upholstery covers and moulded polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat & back (Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are High Back Size: 51.5cm (W) x 82.0cm (H), Seat Size: 53.5cm(W) x 51.0cm(D). High Resilience (HR) Polyurethane foam: the HR Polyurethane foam is moulded with density = 45+-kg/m3 and hardness load 14+-2 kgf as per IS:7888 for 25% compression. Armrest (Thrill Executive Chair): The 3-way adjustable armrest is made of die-cast aluminium with buffing finish designed with the following features: Up-Down adjustment-7 steps (7.0 +- 0.5cm range), It has to & fro movement along with swivel adjustment. Center Tilt Synchro mechanism with multi Lock : The mechanism is designed with the following features : 360° revolving type, 3 position locking with anti shock mechanism. Tilt tension adjustment. Pneumatic height adjustment: The pneumatic height adjustment has an adjustment stroke of 9.5+-0.3 cm. Pedestal Assembly (Thrill Executive): The pedestal is made of die –cast aluminium with buffing finish. It is fitted with 5nos twin wheel castor. The pedestal is 67.0+-0.5cm pitch – center dia. (77.0+-1.0cm with castors) Twin wheel castor: The twin wheel castors are injection moulded in black Nylon. The OEM of the product should be ISO: 9001-2015, ISO 14001-2015 and ISO 45001-2018 certified from NABCB Accredited agency. Product should have certifications like Green guard Gold (UL), BIFMA Level 2, Indoor Advantage Gold, and Green Pro. |
| 22 | La sede high back chairProviding, assembling, transporting & installation of High back Chair specification consisting of :SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3, and hardness load 16 ± 2 kgf for 25% compression. The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. Seat SIZE: 47.6 cm. (W) x 49.2 cm. (D) BACK SIZE: 47.5 cm. (W) x 77 cm. (D)ARMRESTS: The armrest top should be moulded from polyurethane (PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5cm in 5 steps.ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2. The mechanism housing should be made up of HPDC Aluminums black powder coated. SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminums and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. Pitch-center dia. (75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Polypropylene. Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade) Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 23 | Thrill Mid back chairProviding, assembling, transporting & placing / fixing in position Mid Back Chair specification consisting of Seat/Back Assembly – The back is made up of 1.2+-0.1cm. Thick hot-pressed plywood & seat is made up of 1.5+-00.1cm. Thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric upholstery covers and moulded polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat & back (Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are Full Back Size: 51.5cm (W) x 69.0cm (H), Seat Size: 53.5cm (W) x 51.0cm (D). High Resilience (HR) Polyurethane foam: the HR Polyurethane foam is moulded with density = 45+-kg/m3 and hardness load 14+-2 kgf as per IS: 7888 for 25% compression. Armrest (Thrill Executive Chair): The 3-way adjustable armrest is made of die-cast aluminums with buffing finish designed with the following features: Up-Down adjustment-7 steps (7.0 +- 0.5cm range), It has to & fro movement along with swivel adjustment. Center Tilt Synchro mechanism with multi-Lock: The mechanism is designed with the following features: 360° revolving type, 3 position locking with anti-shock mechanism. Tilt tension adjustment. Pneumatic height adjustment: The pneumatic height adjustment has an adjustment stroke of 9.5+-0.3 cm. Pedestal Assembly (Thrill Executive): The pedestal is made of die –cast aluminums with buffing finish. It is fitted with 5nos twin wheel castor. The pedestal is 67.0+-0.5cm pitch –center dia. (77.0+-1.0cm with castors) Twin wheel castor: The twin wheel castors are injection moulded in black Nylon. Product should be certified by a NABCB Accredited agency for conformity assessment . |
| 24 | Greta -2 MB chairProviding, assembling, transporting & installation of Mid Back Chair consisting of :SEAT ASSEMBLY : The seat is made up of 1.5 ± 0.1 cm thick hot – pressed plywood upholstered with fabric and moulded polyurethane foam SEAT SIZE: 51.8cm (W) x 49.7cm (D) BACK ASSEMBLY: The Back is injection moulded in glass filled Nylon which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE): The height adjustable armrest is made of Polypropylene and can be adjusted to 6.0±0.1cm height. It also has swivel and To and Fro adjustment with moulded PU arm top. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort.• Tilt tension adjustment shall be able to operate in seating position. • 5 position Tilt limiter giving option of variable tilt angle to the chair. Seat / back tilting ratio of 1:2. The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron). PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY: The pedestal shall of injection moulded in 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is Ø66.1 ± 0.5 cm (76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Polyamide having 6.0± 0.1cm wheel Diameter.Emmission Class : Product should comply with emission norms CARB (E1 -P2 grade) Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 25 | Sally MB chairProviding, assembling, transporting & installation of Mid Back Chair specification consisting of SEAT ASSEMBLY: The seat is made up of 1.5 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT ASSEMBLY: 47.00CM (W) X 45.70 CM (D) BACK ASSEMBLY: The Back is injection moulded in Glass filled Polypropylene which is upholstered with Mesh fabric. The back consist of adjustable lumbar support made of injection moulded Polypropylene having a nominal thickness of 0.3 ±0.02 cm. BACK SIZE: 48.00cm (W) x 57.60 cm (H). POLYURETHANE FOAM: The polyurethane foam for seat is of density= 48 ± 3kg/m. ARMRESTS (FIXED): The armrest is made of injection moulded Polypropylene which is connecting seat and back. MECHANISM: The mechanism is designed with the following features: 360° revolving type. Centre - Tilt. Tilt with upright lock. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has a stroke of 10 ± 0.5cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5 cm P.C.D. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Polyamide having 6.0± 0.1 cm wheel Diameter. The OEM of the product should be ISO: 9001-2015, ISO 14001-2015 and ISO 45001-2018 certified from NABCB Accredited agency. Product should have certifications like Green guard Gold and Indoor Advantage Gold. |
| 26 | Customized center table 1Supplying and intallation of CentreTable finished in Corian and Gold /Chrome palted legs legs as per theme.Design Description- Table top in shape of Round / Oval finished in corian on 18mm thk ply / particleboard structure. Edge of the table to be 40mm thick with samecorian all corners bevelled with radius of 100mm. Legs are finished in natural matte PU polish.Table to be fitted with 10mm high furniture pads with 31mm dia. ROUND TABLE ( set of 02 with below dimensions) DIA - 600MM & 300MM with 450 MM ht. each |
| 27 | Customized center table 2Supplying and intallation of CentreTable made up of fiber board with acrylic paint finish of size 900mm diameter & 480 mm height.Design Description- Table top in shape of Round / Oval fiber board 40 mm thick with plastic edge banding & finished with acrylic paint supported on under structure made up of solid four legs of width 50 mm which is tapered at bottom to support solid cross rails provided for sturdiness as per drawing to support the table top. All surface finished with acrylic paint & joined with strong adhesive. |
| 28 | Davy Corner tableProviding, assembling, transporting & installation of Corner table of size Dimensions W x H x D (cm)-60 cm W x 45.5 cm H x 60 cm D specification consisting of :• Under Frame : Durable Rubber wood Frame Table Top : Made of high-density plywood Table top : Made with 24 mm thick high-density plywood, Load capacity : with a capacity to support load up to 50 KgsFinish : Plywood Finish Color-Walnut Net Weight ~ 20 (kg)Style-Contemporary Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 29 | Corner table SIZE - 1500L x 500Dx500 W (MM)Custom made corner shelf unit of height 1.5m & width, depth each of approx. 0.5m each made up of particle board and finished with melamine foil with 05 tiers with edgebanding & necessary ficxing arrangement for adjoiing the two shelf unit as per manufacturre's specification. VARBY Corner shelf table. Two unit shall be of different shade as apparoved by EIC. |
| 30 | Magnetic White Board & Pin board 1500Providing and placing magnetic white board and pin board, 600mm x 1500mm, double Faced, magnetic board, 1 side in white to be used as a writing board (with ink markers); other side in green, to be used as writing board with chalks. Both sides shall compatable to be used as magnetic board And green fabric pin board for stackable. |
| 31 | CPU TrolleyProviding & Placing CPU Trolley of Size 230mm W -345mm W X 226mm D X 180mm H. Base tray to be made up of 1mm thick MS CRCA steel and side support to be made up of 0.8 thick. MS CRCA sheet. Injection moulded, Black Nylon Non lockable twin wheel castors shall be provided. Product should be certified by a NABCB Accredited agency for conformity assessment. |
| 32 | Foot restSupplying, transporting and and placing in position of Ergonomic Footrest, with Adjustable Angle, Slip resistant surface. The foot rest Platform Size shall be be 445mm x 295mm as per specifications, reference figures and as direcetd by the Engineer In Charge. |
| 33 | Providing general pest control service to the buildings to control the nuisance of cockroaches, lizards, bed bugs and other insects etc. by once before starting the construction/interior work as directed by Engineer-In-Charge. (Floor area will be measured for payment) |
| 34 | Removing existing door or windows with frame and shutters and making good including finishing the damaged wall surface with CM 1:4 and disposal of removed material to the location approved within the premises etc.complete as per specifications and as directed by EIC |
| 35 | Removing existing plywood shutters with frames, fittings and Dismantling existing cuddapah shelves by cutting with machine of wall cupboards of size 1.2 m X 2.6 m including finishing the damaged wall surface with CM 1:4 and disposal of removed material to the location approved within the premises etc.complete as per specifications and as directed by EIC(Nitch (wall storage ) qty will be measured for payment) |
| 36 | Dismantling aluminium/ Gypsum partitions,fixed glazing and false ceiling including stacking of serviceable material with in premises of building and disposal of unserviceable material to designated place within BARC colony or to a designated BMC dumping ground etc. complete with all leads and lifts and as directed by the Engineer In Charge. |
| 37 | Extending existing outlets of fire extinguisher upto maximum 600 mm lengh (as per site requirement)by providing and fixing GI pipe of 15mm dia with its fittings, clamps etc with painting with red colour with appropriate primer including cutting and making good the walls etc. complete as per specifications and as directed by Engineer In Charge. |
| 38 | Dismantling of existing 6\\"-9\\" brick wall with plaster & tiles (if any) as per demolition layout as per approved drawing/as directed by Engineer In Charge, removing door / windows, stacking of all serviceable material and handing over the same to departmental stores, disposal of debris to designated place within BARC colony or to a designated BMC dumping ground etc. complete with all leads and lifts and as directed by the Engineer In Charge. |
| 39 | Making an opening/cutout in existing 230 mm thick brick masonry including dismantling in floor or walls by cutting masonry for fixing door of size 1.2 X 2.10 m and making good the damages to walls and jambs complete with CM 1: 4 to match existing surface including providing and fixing RCC Precast lintel with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) not exceeding 1.5m in length including the cost of required shuttering and reinforcement including disposal of mulba/ rubbish to the location approved within the premises etc.complete as per specifications and as directed by EIC. (Cost for Supply and installation of new door will be paid in seperate item) |
| 40 | Dismantling and removing old sanitary & plumbing fittings i.e. WC, Basins, taps including old pipelines etc. (connected pipes and fittings at Toilet and pantry at 5th floor , south new extended wing and Toilet at 5th floor south(old wing)(Approximate toilet size 2.0mX1.5m-2nos and pantry platform of length 2.5 mtr) |
| 41 | Disposal of building rubbish/ malba / similar unserviceable, Dismantled or waste materials by mechanical means including loading, transporting, unloading to approved BARC/ municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts etc. complete as per specifications and as directed by EIC. (With Dumper/truck having capacity not less than 10-12 Cum) |
| 42 | Providing and laying Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 and above in cement mortar 1:4 (1cement : 4 coarse sand ) including RCC stiffeners. The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work, racking of joints, scaffolding and curing,etc. completed as directed by Engineer-in-Charge. |
| 43 | Providing, hoisting and fixing at all level precast reinforced cement concrete in small lintels not exceeding 1.5m clear span up to all level including the cost of required centering, shuttering and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). |
| 44 | Providing and applying 12 mm thick internal plaster in one coat in cement mortar 1:3 at all heights and locations for masonry (except stone masonry) and concrete surfaces including racking out joints, hacking of concrete surface, watering, finishing, curing, scaffolding etc. complete. |
| 45 | Providing and fixing polished natural stone tiles(Green marble as approved by engineer) of approved quality, pattern and colour for sill and jambs including preparing the surface and levelling in the desired line, cement mortar 1:3 bedding or backing, cement float, machine cutting, leveling, jointing, smooth cement plastering along the sides to match the existing surface in cement mortar 1:3, filling the joints with neat cement or pigment mixed with cement, finishing, curing etc. complete as directed by Engineer In Charge. |
| 46 | Providing and laying 50-75mm thk. Screed for Floor preparation including loading,unloading, curing etc complete as per specifications and as directed by Engineer in charge. |
| 47 | Providing and laying 600 x 600 x 8 mm thk. approved coloured antiskid / matt vitrified tiles as specified conforming to I.S.15622- 2006 with water absorption less than 0.08% for flooring of an approved, quality, make and pattern /design for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cutting, leveling, jointing, filling the joints by neat cement slurry or approved colour grout, curing, finishing etc complete as directed by Engineer In Charge. |
| 48 | Providing and fixing 8mm thk. vitrified tiles as specified above conforming to I.S. 15622-2006 of approved quality, pattern and colour for flush/projected skirting / riser including preparing the surface and levelling in the desired line, backing of 20 thk. cement mortar in proportion 1:3, square cut top edge or chamfered top edge in cement mortar 1:3, cement float, machine cutting, leveling, jointing, filling the joints with neat cement slurry or pigments mixed with cement, finishing, curing etc complete as directed by Engineer In Charge. |
| 49 | Providing and fixing 8mm thk. ceramic tiles as specified below conforming to I.S. 15622-2006 of approved quality, pattern and colour for dado in the wet area including preparing the surface and levelling in the desired line, backing of 20 thk. cement mortar in porportion 1:3 with approved waterproofing compound, square cut top edge or chamfered top edge in cement mortar 1:3, cement float, machine cutting, leveling, jointing, filling the joints with neat cement slurry or approved colour grout, finishing, curing etc complete as directed by Engineer In Charge. |
| 50 | Providing and laying solidwood flooring of 25 mm thickness ( wooden planking, tounged & grooved), of second class teak wood ( herringbone pattern ) including providing removable solidwood panels at the locations of underfloor Electrical cable trunk / raceways including providing and laying threshold of appropriate material . The rates are inclusive of all consumables like adhesive, screws and nails as per manufacturer's specifications, tools and tackles, Labours, transportation, taxes, wastage etc complete all as per drawings, technical specifications and as directed by the Engineer-in-charge |
| 51 | Providing installing 5 mm thick SPC (Stone plastic composite) SPC Plank click & Lock flooring of approved make design/pattern of Wellspun (Eden category) or equivalent make approved by EIC and installed by company authorised installers including providing and laying 2mm biofoam sound buffer layer below the SPC flooring, including preparation of subfloor, levelling of small undulations with SBR polymer modified cement based screed/plaster of paris as may be required and as directed by EIC, filling of depressions in floor after dismantling of walls with 50-75mm thk. concrete screed (1 part cement :2 parts sand:4 parts zero size aggregate), finally cleaning the floor after laying with mineral spirit/stain remover etc complete as per manufacturers specifications, Inclusive of all materials and labour costs etc. complete and as directed by the Engineer. |
| 52 | Providing and fixing Approved vinyl plank flooring having 2 mm thick of approved pattern and shade including necessary adhesive over the IPS/ Mosaic flooring / Skirting including cutting to the required size and shape including wastage, removing existing vinyl flooring/carpet in the wing, cleaning the flooring before and after the completion of works all as per manufacturer's specifications in general and as per approved pattern (Harringbone), including disposal of debris within BARC colony or to a designated BMC dumping ground etc. Complete with all leads and lifts and as directed by the Engineer In Charge. etc complete and as directed by EIC. |
| 53 | Providing and constructing raised platform of 750 mm wide and 600 to 750mm high using minimum 40mm thick polished kadappa stone slab base with minimum 15mm thk. polished stone top as specified below of approved quality, colour and texture, supported by both side polished, 40mm thk. and minimum 700mm wide kadappa spaced at not more than 1200mm clear, including polished facia of min. 100mm height as specified below with champhered/ rounded at the top edges, jointing in approved adhesives, machine cutting, making opening for sink and fixing the same in position, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with pigment mixed with cement, cleaning, finishing, curing etc complete as directed by Engineer In Charge. (The cost of providing the sink shall be paid extra as per plumbing items)- Ruby red / jet black / Hasan green Granite slab at top and facia. |
| 54 | Providing waterproofing treatment through specialized agencies as per specifications to the flooring of existing water closets, bathrooms, kitchen, nahanies, washing places, sanitary blocks etc. including removing existing flooring and brickbat coba etc. by giving INJECTIONS with cement solution with water proofing compound into the floor slab so as to make it consistent, homogeneous and impervious against leakage, seepage etc. The sunk portion shall then be covered with brickbat waterproof coba in 1:5 c.s. of required thickness with necessary gradient for easy flow of water. Finally the floor shall be covered with joint less waterproof cement plaster in 1:3 c.s. 12 mm to 15 mm thick finished rough for receiving tiles. The average thickness of complete treatment shall not be less than 100 mm. The soil pan area will not be deducted. ( After completion of work leakage test shall be carried out after impounding the water for 7 days without any extra cost. The actual treated area will be measured and paid for). |
| 55 | Providing waterproofing treatment through specialized agencies to the dado portion of the R.C.C. side walls upto 1.5 m height from floor area of existing water closets, bath-rooms, kitchens, washing places, sanitary blocks etc. by removing existing plaster and tiles etc. and giving ,INJECTIONS‟ treatment with waterproofing compound and cement solution. The walls will then be plastered with waterproof cement plaster in 1:4 c.s. 12 mm to 15 mm thk. Finally the walls shall be covered with jointless waterproof plaster in 1:3 c.s. 12 to 15 mm thick finished rough for receiving tiles. The average thickness of complete treatment shall not be less than 25 mm. (The actual treated area will be measured and paid for). |
| 56 | Providing and fixing fully glazed partition, 12 mm th. toughened glass partition fixed on heavy AL U channel with PVC, concealed in floor and fixed at false ceiling level with TW frame including hard transparent PVC sealant between two glass panels ( Falcon make ) as per design and as directed ( AL framework above false ceiling to be measured separately ) |
| 57 | Providing and fixing framed 12 mm th. toughened glass door on approved patch fittings including floor spring, 30 mm dia.brush S S handle ( 600 mm high ), lock etc. as per drawing and as directed ( Hettich/Dorma/Hafele make patch fittings ) |
| 58 | Refurbishing of existing door of size 1.0 X 2.10 with door frame by making the cut out for 4mm thick glazing panel in existing door shutter ,replacing existing laminate of shutter and frame with high quality 6mm thick MDF plain board, finishing the surfaces with two coats of PU Paint including making grooves on one coat of appropriate primer. Also includes removing existing door shutter and refixing after refurbishing the same with teak wood beading and lipping wherever required; It also includes providing and fixing new high quality SS fittings and fixture like 6 lever mortice latch with handle, hinges, door closer, door stopper, tower bolt etc. complete as per specifications and as directed by EIC.( Cost for the painting work shall be paid in separate item) |
| 59 | Providing and fixing superior quality single leaf B.W.P. grade solid core flush door shutters of standard make conforming to IS:2202- 1991 (Part I & II) including finishing with approved laminate on both side etc. with 12 mm thk teak wood lipping all around etc. complete including necessary SS fixtures and fittings, SS butt hinges, 6 lever Chromium pleated brass Mortice locks with handle, 150 mm SS tower bolt, door stopper, 20 x 4 mm size MS hold fasts welded to angle frames and grouted in 100 mm thick cement concrete 1: 2 : 4, including finishing with the 1.0 mm thick desired finish laminate etc., all complete as per drawings, specifications and as directed by the Engineer. |
| 60 | size 3'0\\"X7'0\\" |
| 61 | size of 2'6\\" x 7'0\\" (Toilet doors) |
| 62 | Providing and fixing trap doors made out of 38 mm x 25 mm thk. T W frame placed at 450 mm c/c in both directions with 6 mm th.Marine plywood ( BWP :710 ) on both sides finished with 1 mm thk. laminate on either side including brass hinges, stopper, L N Key, and T W framework to support trap door etc. as per drawing and as directed |
| 63 | Providing and fixing best quality C.P. Teak wood frame for doors, size greater than 50mm x 50mm including intermittent supports if required, all moulding, rebating, jointing, hold fasts of MS flats of minimum size 25 x 3 mm, having length of 225 mm for doors & 150 mm for windows etc. complete as per specifications and as directed by EIC. |
| 64 | Providing and fixing anodized (anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodising must be scaleted by keeping the anodized section in boiling deanodized water for a period of one hour) aluminum fixed/ sliding / pivoted / top hung / side hung / louvered type windows, doors, ventilators and partitions conforming to IS:1948, 1961 with hollow bottom section & standard single / two / three / four track frame section all round (top, bottom and sides) with shutter frame made up of standard handle section standard interlocking section and standard top and bottom section with infill panel of plain / frosted / tinted glass/ Novapan sheet / acrylic sheet / hardner laminated sheet as listed below with nylon guides, gliders glass fixing PVC weather strips, neoprene gasket, PVC weep holes etc complete with approved type of locking arrangement, handles and other fixtures including fixing, filling the gaps with silicon sealant, cleaning polishing the aluminium section with petrol and / or other agents as specified by the manufacturers etc. complete as directed by Engineer In Charge. |
| 65 | Extra for Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): |
| 66 | Providing and fixing 9 mm thick BWP grade marine plywood confirming to IS:710 of approved make with necessary glue, screws, nails etc. complete as per specifications and as directed by Engineer in charge. (Cost for the framework shall be paid in separate item) |
| 67 | Providing and fixing 10 mm thick Cement bonded particle board (Termite, fire and moisture resistance as per IS 14276: 1995 including all necessary glue/adhesive, screws, nails etc. complete as per specifications and as directed by EIC. (Cost for the framework shall be paid in seperate item) |
| 68 | Providing and fixing sound & thermal insulation with 50 mm thick resin bonded rock wool confirming to IS:8183 having density 48kg/cum, wrapped in 200G virgin polythene bags fixed to wall with screw, rawel plugs & washer and held and in position by criss crossing GI wire etc. complete as per specifications and as directed by Engineer in charge. |
| 69 | Providing and fixing in position Fab Stretch TRV Acoustic Panels of approved sizes having 25mm thickness made up of Anutone Board of 380 gsm Density having NRC / STC up to 0.85 with 95% Rh Moisture resistance installed with vinyl tracks or other equivalent make covered with fabric of approved make shade and color complete as per Manufacturers specifications etc. complete as per specifications and as directed by EIC. |
| 70 | Providing and fixing 12mm thk. MDF fluted Panel with PU finish, as per design and as directed ( Basic cost of designer panel Rs.2500/- Sq.Mt. excluding GST ) cost includes the two coats of approved PU paint with appropriate primer etc. complete as per specifications and as directed by EIC. (Cost for the framework & paint shall be paid in separate item) |
| 71 | Providing and fixing 18mm thick high quallity MDF board with all necessary glue/adhesive, screws, nails etc. complete as per specifications and as directed by EIC.(Cost for the framework shall be paid in separate item) |
| 72 | Providing and fixing 12.5 mm thick Gypsum board as per standard sizes fixed with self drilling/taping screws / fasteners at 600mm c/c of approved make, proper taping and acrylic based jointing compound for seamless finish including finishing with gypsum putty etc. complete as per specifications and as directed by EIC.(Cost for the framework shall be paid in seperate item) |
| 73 | Potted Planters: Supplying and placing in position potted planters of size (2'-6\\" x 1'-6\\") with good quality artificial flowers, as Per approved pattern, design, style and make approved by EIC. Basic price Rs. 4000/- |
| 74 | Supply and placing in position various artificial plants as per approved design, pattern, colour/shade. Basic price Rs. 3000/- |
| 75 | Supply and placing in position rugs of size 2.0 X 1.5 as per approved design, pattern, colour/shade. Basic price Rs. 10000/- |
| 76 | Portraits: HD quality Photo of SIZE 3'-0\\" x 5'-0\\"with lamination and frame using high quality photo paper and printing ink as approved by EIC. Basic PRICE Rs. 15000/- |
| 77 | Supply and installation of curtains of approved make as per architect selection . MAIN FABRIC. WITH CHANNEL, FITTING & 3 PLT CURTAIN STICHING, FIRE RETARDANT FABRIC , DIMOUT TEXTURE SA 1729 WITH FR SHADE 53013 , 330 GSM, 100% POLYSTER, 140 CMS WIDTH , POWER COATED SMOOTH CHANNEL, 3 PLT STICHING WITH FITTING. WINDOW SIZE 4.3 MTRS X 3MTRS. Work complete including all type of stitching , fixing , accessories ,inclusive of installation, material cost, labour, wastage, operating system all tools tackles, scaffoldings, hardware at all floors, all levels and heights, necessary edge binding with approved fabric and thread of colour similar to the colour of the blinds. Same rate shall be applicable for all heights and for all floors. Maximum size of curtain shall not exceed 4.85 m along the length of the opening and 3.050 m along the height of the opening & height will be measured from top of the pelmet to sill bottom lvl. height will be measured from top of the pelmet to sill bottom lvl etc. complete as per specifications and as directed by engineer in charge. |
| 78 | Console : Supply and placing in position readymade decorative Console of metal / wood / glass / fibre / mdf or any other material with mix composition as per approved design, pattern, colour/shade. Basic price Rs. 30000/- |
| 79 | Signages : Providing and fixing signages made from SSplate (SS 304) of appropriate sizes as per instruction of Archiect/EIC etc. complete as per specifications and as directed by EIC. |
| 80 | Supplying and fixing in position Roller blinds for windows (Vista/Mac/Armstrong/DECK or equivalent) made with fabric of approved quality, design, make and shade comprising of polymer coated fiber fabric approved by the EIC. The roller mechanism shall be a molded unit made from engineering grade plastic polymer with steel spring support. The fabric shall be finished on the sides with edge tape duly welded for waviness control. The fabric shall be attached to the roller tube with high quality selfadhesive tape, with smooth manual operation, with all fittings complete as per manufacturer's specifications. Rate should including removing existing vertical blinds and disposing the material as directed by EIC etc. all complete as per specifications and as directed by EIC. |
| 81 | Providing and fixing of glass film of approved quality, make and brand including preparation of surface and fixing as per manufacturers specifications. and directed by EIC with all labour, materials, transport etc. all to the satisfaction of the EIC . |
| 82 | Providing and fixing a naming board of size 1250X900 mm made of 19mm thick BWP grade marine plywood finishing with 4.0 mm thick approved veneer on one side , all edges finished with 12 mm thick teak wood beading and all finished with melamine polish . It also includes removing old brass letters from existing board, polishing the same and refixing the same on new board with proper adhesive etc complete as per specifications and as directed by EIC |
| 83 | Providing and fixing Golden/Silver coated brass Letters (Approx 40 Nos letter of diff sizes) |
| 84 | Logo to be ethced in the 12mm thick toughened glass with designer logo as per the design. |
| 85 | Providing and laying decorative high quality pebbles. |
| 86 | Providing and applying vinyl stickers on glass including cost of high quallity printing as per theme provided by Architect/EIC and fixing on glass etc. complete as directed by EIC. ( Cost of the glass will be paid in separate item) |
| 87 | Providing, fabricating, supplying and fixing LED backlit logo of HWB/ DAE/ signages comprising of opal acrylic front face with reverse UV printing, complete with LED illumination system and ACP backing, as per approved design and direction of Engineer-in-Charge.Note: Front face area shall be measurd for the purpose of payment |
| 88 | P&F in position Gypsum board false ceiling with 12.5mm thk. Gypsum boards, screwed/ fixed to the under struct of suspended G.I. Grid constructin & suspended from the main ceiling of ceiling section at max c to c distance of 450 mm perimeter channel and intermediate channels at max c to c distance 1200 mm galvanised grid should be fixed to RCC slab. The gypsum board should be fixed to galvanised iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should includes necessary additional ceiling sections and intermediate channels to be provided at openings for light fixtures, asbestos cement ducts, vertical drops, offsets etc. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 mm item to be completed in all respect. (G.I. perimeter channel size-27mmx0.5mm thk.,flange-20mm &30mm,intermediate channel. size-45mm & 0.9mm thk., hanger size-25mmx0.5mm thk.) including making provision for cutouts and / or trap door for electrical and mechanical systems, etc complete as directed by Engineer In charge.etc. complete. as per specifications and as directed by EIC. |
| 89 | Providing and fixing false ceiling with eco-friendly light weight calcium silicate tiles approved make or equivalent of size 595 x 595mm having 15 mm thick densified microlook edge and 100% humidity resistence, incombustible as per BS 476 Part IV and thermal conductivity 0.043 w/m° KC and NRC 0.50 placed in true horizontal level suspended grid of size 600x600 mm made from hot dipped GI steel sections on Sillhoutte profile, rotary stitched double webbed white with 6mm reveal profile white/black), where in main T runner of size 24 mm x 38mm and 0.33 mm thick @ 1200mm center to center and cross T of size 24mm X 28 mm and 0.33 mm thick, 1200 mm long spaced between main tee at 600 mm centre to centre and secondary cross T of Size 24mm X 28 mm x 0.33 thick of length 600 mm to be interlocked at middle of the first cross T in each panel to form grids of 600 mm x 600 mm and resting on periphery wall profile wall section 24 mm x 24mm x 0.40 thickness and laying false ceiling for services like diffusers grills including cutting, making opening for light fitting, fixtures, smoke detectors etc. wherever required, main tee runner to be suspended form ceiling using G.I. soffit cleats of size 25 x 35 x 1.6 mm of required length fixed to the ceiling with12.5mm dia and 50 mm long dash fastener, 4 mm dia G.l adjustable rods with good quality G.I level adjustment clips of 85 X 30 X 0.8mm spaced at 1200 mm center to center along main tee all complete at all heights as per specifications, drawings and as per direction of Engineer - in - Charge. |
| 90 | Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part -1 & II) 1976, applied on hacked/ uneven background such as bare brick/block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete. |
| 91 | Painting with two coats of premium interior emulsion paint (Royale paint of Asian Paint or equivalent approved by EIC ) over two coats of compatible primer as per manufacturer's recommendation (Royale base coat or equivalent approved by EIC) using expert labour including preparation of surface even and smooth, cleaning, etc. complete as per specifications and as directed by the Engineer. |
| 92 | Providing and applying Textured paint of approved quality, shade and design as per specifications with one coat of appropriate primer, base coat etc complete as per specification and as directed by the Engineer -In- Charge. |
| 93 | Providing and applying two coats of Polyurethane paint of approved quality, shade and design as per specifications with one coat of appropriate primer etc complete as per specification and as directed by the Engineer -In- Charge. |
| 94 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm or of appropriate size as per site conditions & of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including providing & fixing seat cover, and cistern fittings, pipe,nuts, angle cock/ bib cock, bolts, gasket , CP brass health faucet with flexible hose of 1 m length wall hook mount, and all necessary installation hardwaret all as per scope of work & technical specifications etc. all complete safely as directed by EIC. |
| 95 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including fittings and brackets,painting, cutting and making good the walls wherever require: a)White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tapb)Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 96 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including fittings and brackets,painting, cutting and making good the walls wherever require: a) Stainless Steel AISI-304(18/8) Round basin 405x355 mm with single 15 mm C.P. brass pillar tapb)Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 97 | Providing and fixing C.P. brass stop cock (concealed)/ angle cock on 15 mm nominal bore of standard design and of approved make conforming to IS:8931 including fixing of700 mm long flexble tube etc. complete as per direction of engineer-in-charge |
| 98 | Supply, installation, testing & commissioning of PVC Multi floor Trap as per IS 14735, with material and labour etc. complete as per directions of engineer-in-charge. |
| 99 | Providing and fixing a high-quality 600 mm hand towel rail of approved make and design, made of stainless steel (SS304) or equivalent corrosion-resistant material. The towel rail shall be securely fixed to the wall using stainless steel screws and necessary hardware. The work includes proper alignment, drilling, fixing with wall plugs, and ensuring a firm installation. |
| 100 | Providing and fixing a high-quality napkin ring of approved make and design, made of stainless steel (SS304) or equivalent corrosion-resistant material. The Napkin ring shall be securely fixed to the wall using stainless steel screws and necessary hardware. The work includes proper alignment, drilling, fixing with wall plugs, and ensuring a firm installation. |
| 101 | Providing, fixing, testing and commissioning in position SWR PVC PIPE TYPE-B(4Kg/cm2.) self fit pipe conforming to IS:13592 including all fittings such as bends, junctions, inspection doors, offests, cowl, access pieces/plugs ,including all vertical and horizonal hevay duty MS pipe supports & clamps, wall etc. jointing with PVC Adhesive joints including cutting holes in walls and making good the same with necessary fittings as per direction of Engineer in (INSIDE THE TOILET / KITCHEN / CONNECTION TO VERTICAL DOWNTAKE) |
| 102 | Size : 110 mm dia. |
| 103 | Size : 75 mm dia. |
| 104 | Size : 50 mm dia. |
| 105 | Size : 40 mm dia. |
| 106 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threated fittings including fixing the pipe with GI Supports & clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cemetnt and testing of joints complete as per direction of engineeer in charge. Scope shall also include chasing in wall by diamond cutters wherever required and making good the same as per direction of Engineer in Charge.(INSIDE THE TOILET / KITCHEN / CONNECTION TO VERTICAL DOWNTAKE) |
| 107 | Size : 15 mm dia |
| 108 | Size : 20 mm dia |
| 109 | Size : 25 mm dia |
| 110 | Size : 32 mm dia |
| 111 | Providing and fixing 6mm thick plain mirror of approved quality, machine edge polish, fixed with 25 mm dia brush S S studs or with silicon including 12 mm SS channel on edges including 12 mm thk. back bison board as per drawing and as directed ( Toilets - above wash basin counters ) SIZE 3'0\\"X3'0\\" |
| 112 | Rebate for following items which includes removing the scrap & disposal of the same outside the premises |
| 113 | Rebate for scrap material i.e door shutters, plywood shutters etc |
| 114 | Rebate for scrap material i.e plywood shutters etc. |
| 115 | Rebate over dismantling existing Aluminium sliding/openable door and window ventilatior etc |
| 116 | Electrical works |
| 117 | Dismantling and removal of existing electrical installations in a safe and professional manner from office / meeting rooms. The scope includes disconnection and removal of approximately 125 electrical items comprising light fittings, ceiling/wall fans (including switch sockets as a part of item ) and other associated electrical accessories. All dismantled materials shall be carefully handled and handed over to department. The contractor shall ensure no damage to equipment / civil structures and follow all electrical safety norms during execution. |
| 118 | LED lights |
| 119 | 6W LED (4inch):Supply, installation and commissioning of 6W LED downlight fixture (Philips or equivalent make) with adjustable color temperature (warm to cool) suitable for mounting on false ceiling in office rooms. The scope includes providing all necessary accessories for installation and making electrical connections using FRLS PVC insulated copper conductor wires/cables for phase, neutral, and earthing from the available point. The installation shall be carried out in a neat and safe manner, ensuring compliance with relevant IS/IEC standards and electrical safety norms.Luminarie shall have DALI DT8 compatible drivers |
| 120 | 15W LED downlight fixture (6inch Dia)Supply, installation and commissioning of 15W LED downlight fixture (Philips or equivalent make) with adjustable color temperature (warm to cool) suitable for mounting on false ceiling in office rooms. The scope includes providing all necessary accessories for installation and making electrical connections using FRLS PVC insulated copper conductor wires/cables for phase, neutral, and earthing from the available point. The installation shall be carried out in a neat and safe manner, ensuring compliance with relevant IS/IEC standards and electrical safety norms.Luminarie shall have DALI DT8 compatible drivers |
| 121 | 7W LED spotlight fixture:Supply, installation and commissioning of 7W LED spotlight fixture (Philips or equivalent make), with adjustable color temperature (warm to cool) suitable for mounting on false ceilings in office rooms. The scope includes the provision of all necessary mounting hardware, accessories, and making electrical connections using FRLS PVC insulated copper conductor wires/cables for phase, neutral, and earthing from existing wiring points. The work shall be carried out in a neat, safe, and professional manner, strictly adhering to relevant IS/IEC standards and established electrical engineering practices.Luminarie shall have DALI DT8 compatible drivers |
| 122 | High-lumen efficacy LED strip lights for cove lighting:Supply, installation and commissioning of high-lumen efficacy LED strip lights with adjustable color temperature (warm to cool) for cove lighting, suitable for mounting on false ceilings. The scope includes supply and fixing of LED strips with matching LED drivers as per circuit requirement, and all necessary mounting accessories, connectors, and support materials. Electrical connections shall be made using FRLS PVC insulated copper conductor wires/cables for phase, neutral, and earthing from the existing power point. The entire system shall be installed in a neat and secure manner, conforming to relevant IS/IEC standards and good engineering practices. LED drivers shall be included as an integral part of this item.Luminarie shall have DALI DT8 compatible drivers |
| 123 | Decorative Lighting - Type-1 (1200mm)A set of two Nos of 1200mm LED pendant linear light. Modern Wooden LED Pendant Light, Minimalist Ceiling Lighting for Office, Straight Bar LED Hanging Liner Teak Wood LightsDimensions 2D x 2W x 48H InchesSleek wooden LED pendant light shall be crafted from high-quality wood such as teak, energy-efficient illumination, ideal for office spaces. LED light shall be suspended with subtle wires to create floating effect. Lamp must be of the most reputed brandLuminarie shall have DALI DT8 compatible drivers |
| 124 | Decorative Lighting - Type 24 Light 4 Rectangular Ring Brass Gold Modern Double LED Chandelier for Dining Living Room Office Hanging Suspension Lamp The Top Ring Length is 1200mm The Middle Ring Length Is 1000mm And The two Lowest Ring Length is s 600mmLuminarie shall have DALI DT8 compatible drivers |
| 125 | Decorative Lighting - Type- 3Gold Metal ARC FLOOR LAMP LIVING ROOM STANDING LAMP - Antique Flexible architect swing arm floor standing lamp which makes easy to find the perfect lighting angle, perfect for reading, also a classic office décor. Total height shall be around 1500mmLuminarie shall have DALI DT8 compatible drivers |
| 126 | Supply installation and commissioning of DALI System & 10 Button Tactile Press Keypad one system for one room i.e. 6Nos of DALI systems along with keypad for 5Nos of rooms for controlling illumination as per technical specifications. |
| 127 | Wiring |
| 128 | Point Wiring for Light point with Modular Accessories:Wiring for light point point using 1.5 sq.mm FRLS PVC insulated copper conductor single core wire, drawn through surface/ recessed Fire Retardant HR PVC conduits along with the wiring for the DALI system including the supply and installation of wiring for the DALI communication, modular switch, modular plate with suitable GI box, and earthing of the point using 1.5 sq.mm FRLS PVC insulated copper conductor wire. The work shall be executed with neatness, safety, and good workmanship, ensuring proper terminations and secure mounting. All materials and workmanship shall conform to relevant IS/IEC standards and standard electrical installation practices. |
| 129 | Supply and Fixing of Modular Socket with Switch in GI Box (Only for Switch Socket Combination)Supplying and fixing of suitable size GI box with modular plate and cover, suitable for mounting on surface or in recess, including the supply and installation of 1 no. 6-pin modular socket (5/6A & 15/16A combined) and 1 no. 15/16A modular switch. The item shall be complete with all necessary connections, mounting hardware, and accessories.Installation shall be carried out in a neat, secure manner with good workmanship, strictly conforming to relevant IS/IEC standards and standard electrical installation practices, ensuring durability, safety, and proper functionality. |
| 130 | Wiring for Power Circuit (Power Socket, DB to Switchboard, etc.)Wiring for power circuit applications such as power sockets, DB to switchboard connections, etc., using 2 nos. of 4 sq.mm FRLS PVC insulated copper conductor single core wires for phase and neutral, drawn through surface/recessed steel conduit, along with 1 no. of 4 sq.mm FRLS PVC insulated copper conductor wire for loop earthing.The wiring shall be carried out from the designated power source (e.g., socket or DB) to the end equipment (e.g., switchboard or AC unit), ensuring proper termination, clamping, support, and electrical safety. The entire installation shall conform to relevant IS/IEC standards and good electrical engineering practices. |
| 131 | Supply and Fixing of Modular GI Box with 16A SP MCB for Air Conditioner CircuitSupply and fixing of suitable size modular GI box with front plate, including the installation of 1 no. 16A Single Pole MCB (C-curve) for the air conditioner circuit. The scope includes all required mounting accessories, interconnections, and electrical terminations. The installation shall be carried out on surface or recessed wall, ensuring a neat, secure, and electrically safe setup, in strict compliance with relevant IS/IEC standards and standard electrical engineering practices. |
| 132 | Supply, Installation, Commissioning and Guarantee of Inverter Split / Cassette Air Conditioner |
| 133 | Supply, installation, testing, commissioning, and performance guarantee for one year of 1.5 TR, inverter-type, 5-star rated cassette air-conditioners of Voltas / Daikin or equivalent make, suitable for efficient and quiet cooling in office environments. The scope includes all materials, accessories, mounting frames/hardware, indoor-outdoor supports, gas charging (if required), and tools necessary for successful installation and commissioning, excluding copper refrigerant piping, drain piping, and power cables (i.e. from indoor to out door unit, but, incoming cable of 5 meter for each unit shall be in scope of this item), which will be provided separately. Each AC shall also be supplied with weather proof 2P+E, 16A, 220-250V, IP66, IK08 Plug-Socket.The installation shall be carried out in a neat, professional, and safe manner, ensuring compliance with manufacturer guidelines, IS/IEC standards, and good HVAC engineering practices. The supplier shall provide comprehensive on-site warranty support for 1 year from the date of commissioning. |
| 134 | Supply and Laying of Insulated Suction and Discharge Copper Tube Set :Supply and laying of insulated copper tube set, comprising both suction and discharge copper tubes with factory-fitted or field-applied closed-cell thermo insulation, suitable for use with the 1.5 TR inverter cassette air-conditioners supplied under Item No. 5.i. The copper tubes shall be of appropriate diameter and wall thickness as per manufacturer’s specifications, suitable for high-pressure refrigerant flow, and compatible with the refrigerant used (e.g., R32/R410A).The laying shall be done in a neat and secure manner, routed through ceiling or wall spaces as required, ensuring proper bending radius, clamping, and insulation integrity, in compliance with standard HVAC practices and relevant IS/ASHRAE norms. |
| 135 | Supply, Laying, Dressing, and Connection of Drain Pipe and Armoured FRLS Cable for Cassette Type ACs:Supply, laying, dressing, and connection of the following for cassette type air conditioners supplied under Item No. 5.i:a. PVC Drain Pipe of approved quality and suitable diameter, reinforced with polyester/nylon mesh, for effective condensate drainage from the indoor unit. The pipe shall be laid with proper slope, securely clamped, and terminated at designated drain points, ensuring leak-proof and maintenance-friendly installation.b. Armoured FRLS Cable of suitable size for power and control connection between the outdoor and indoor units, laid through approved routes (surface/recessed/tray), with proper dressing, glanding, termination, and earthing as required.All materials, workmanship, and installation practices shall conform to relevant IS/IEC standards and manufacturer guidelines, ensuring electrical safety and system performance. |
| 136 | Supply and Installation of MS Stand for Outdoor Unit:Supply and installation of a sturdy and stable stand fabricated from mild steel (MS) sections as per dimensions and specifications provided in the enclosed drawing, suitable for mounting the outdoor condenser unit of the air-conditioning system. The stand shall be duly painted with one coat of red oxide primer followed by two coats of grey synthetic enamel paint to ensure corrosion resistance and long-term durability.The stand shall be installed at the specified location, ensuring proper leveling, anchoring, and load-bearing capacity, in accordance with manufacturer recommendations, structural safety norms, and good fabrication and installation practices. |
| 137 | Miscellaneous |
| 138 | Supply and Fixing of 25mm Fire Retardant HR PVC Conduit with Accessories:Supplying and fixing of 25mm medium class PVC conduit complete with necessary accessories (bends, couplers, junction boxes, saddles, etc.), laid on surface or recessed in wall/ceiling. The scope includes cutting and chipping of walls for recessed installation and making good the surface after laying, restoring it to its original finish. Installation shall ensure proper alignment, support at regular intervals, and shall be carried out in accordance with relevant IS standards and good electrical installation practices. |
| 139 | Spares |
| 140 | 15W LED (4inch) |
| 141 | 15W LED downlight fixture (6inch Dia) |
| 142 | 7W LED spotlight fixture |
| 143 | High-lumen efficacy LED strip lights for cove lighting |
| 144 | DALI System along with key pad |
| 145 | Instrumentation works (Supply of CCTV system as per technical specifications) |
| 146 | IP based Fixed Dome Camera |
| 147 | 32 Channel NVRwith 90 days stoarge capacity alongwith central Management Software having perpetual license/vailidity |
| 148 | WorkStation PC attached to NVR with 23\\" Display |
| 149 | Operator Client WorkStation PC |
| 150 | 42\\" Display Monitor |
| 151 | 24 Port POE Switch including SFP port & transceiver modules |
| 152 | 6 Duplex port Fully loaded LIU & FO patch cords |
| 153 | 6 U Wall mount Rack |
| 154 | Cat 6A Cable (1 Bundle=305 meter) |
| 155 | 6 Core Single Mode Optical Fiber Cable |
| 156 | PVC Conduit with accessories |
| 157 | Installation, Testing and Commissioning of CCTV System including supply of asasociated accessosries required for completeness of system |
| 158 | Supply & installation of Smoke Detectors , Response Indicators, cables and associated accessories for augmentation of existing Fire Alarm System as per tender technical specifications |
| 159 | Supply, Installation, testing & Commissioning of Smoke Detectors compatible with existing Shrack Make Fire Alarm System. |
| 160 | Supply, Installation, testing & Commissioning of Response Indicators compatible with existing Shrack Make Fire Alarm System. |
| 161 | Supply & laying of 2 core 1.5 sqmm FRLS cable for interconnection between existing detectors installed on ceiling to new detectors and response indicators installed at false ceiling. Programming & configuration of the new detectors in FACP/GUI through OEM/ system integrators of m/s Shrack. |
| 162 | Shifting of existing detectors installed on ceiling to the new position as per site requiremnent. |
| 163 | Supply & Installation of Telephone Line Jack (RJ 11) , RJ 45 jacks, requisite CAT 6A cables and associated accessories for augmentation of existing Telephone System as per tender technical specifications |
| 164 | Supply & Installation of suitable Telephone Line Jack (RJ 11) with Flush mounting socket for desks/tables |
| 165 | Supply & Installation of suitable RJ 45 jacks on walls for connection of existing telephone lines |
| 166 | Laying & crimping of CAT 6A UTP cables from RJ45 Jacks mounted on wall to RJ 11 ports mounted on desks/tables for telephone connection. |
| 167 | Allied IT works |
| 168 | HDMI Cable with Connectors. Length: 10 Meter (max) |
| 169 | USB Cable (Type-C) with Connectors. Lenthg: 3 Meter (Max) |
| 170 | Cable Cubby with USB, HDMI, Power point, RJ45 Sockets |
| 171 | RJ45 Connectors Box |
| 172 | Installation charges for allied IT work Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysSep 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender