Tender For Repair / Replacement To Rolling Shutter, Roof Sheet, Eaves Board, Sliding Shutter, Tilling, Plastering And Connected Works At Technical Area And B/R Maintenance Work At Mes Installation No-2 Area Pump House And Sub Power House Under Ge (Af
Tender Value
35 Lakhs
Estimated cost
Bid Submission
02 Sep 2026
10 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Budgam → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Replacement To Rolling Shutter, Roof Sheet, Eaves Board, Sliding Shutter, Tilling, Plastering And Connected Works At Technical Area And B/R Maintenance Work At Mes Installation No-2 Area Pump House And Sub Power House Under Ge (Af) Srinagar.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 2 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n exc 4.0 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 3 | Taking down shutters of any description size of shutter exc 1 Sqm but n.exc 2 Sqm and removing from site complete all as specified and directed. |
| 4 | S&F for pressed steel frame made out of mild steel 1.25mm thick sheet, with size of frame 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. and applying a shop coat of red oxide primer including providing PCC 1:3:6, type C-0 (using 12.5mm graded crushed stone aggregates) as in back filling of pressed steel frame, complete all as specified and directed. |
| 5 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying and fixing in opening, complete all as specified and directed. |
| 6 | S&F 30mm thick Factory made Solid Panel PVC Door Shutter (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed. |
| 7 | S&F 30mm thick 2nd class softwood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers, complete all as specified and directed. |
| 8 | S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed. |
| 9 | Preparation of new wood and wood based surfaces of any description exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 10 | S&F steel window with side hung shutter, factory made, including Box type / projecting type hinges with steel handle, tower bolts 100 mm, steel peg stay, with glazing bars including applying one shop coat of red oxide primer, complete all as specified and directed. |
| 11 | S&F steel window with side hung shutter, factory made, including Box type / projecting type hinges with steel handle, tower bolts 100 mm, steel peg stay, without glazing bars including applying one shop coat of red oxide primer, complete all as specified and directed. |
| 12 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 13 | S&F 3mm thick sheet glass ordinary quality and glazing with oil putty / wooden beading in squares not exceeding 0.50 Sqm, complete all as specified and directed. |
| 14 | S&F 100mm long medium weight, cold rolled mild steel Butt hinges, complete all as specified and directed.. |
| 15 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed. |
| 16 | S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 17 | S&F 150mm size Aluminium handles, cast type, anodised, complete all as specified and directed. |
| 18 | S&F 3mm thick sheet glass ordinary quality and glazing with oil putty / wooden beading in squares not exceeding 0.50 Sqm including hacking old glass, complete all as specified and directed. |
| 19 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 20 | S&F GI frame work of size 605 x 605mm for seamless ceiling for snap grid ceilling made out of angle section 22 x 22 mm on perimiter walls and tee section of 22 x 22 mm in web made to shape out of GI sheet, bottom of section are powder coated all arrangements to make a grid of desired size as directed. these section fixed to walls with nylon sleeves and screws at 450 mm centre to centre and sunpended work 6 mm dia GI up to 1200 mm only including supply and fixing 12 mm thick Gypsum Board(water proof) fixed with screw or as per manufacturers instructions and jointing and finishing to a flush finish of tapered and square edges other board any other joints with recommended jointing compound over jointing tapes, finishing with one coat of primer and two coats of oil emulsion distemper over a coat 2mm thick wall care putty including dismantling of existing ceiling, complete all as specified and directed. |
| 21 | S&F in repairs 6mm thick plywood fixed in ceiling or laid / inserted to timber / GI / aluminium framework with screws including putty to receive finishes, including height up to 10m in ceiling, complete all as specified and directed. |
| 22 | Preparation of new or previously untreated plaster/ AC sheet / Gypsum board surfaces of ceiling including cornices and applying two coats of oil bound distemper colour / tint, complete all as specified and directed. |
| 23 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 24 | M&L for rolled mild steel work in Plates (plain or chequerred ) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 410-W (gde-E-250) Quality B complete all as specified and as directed. |
| 25 | M&L for mild steel framed work such as grills, gratings, gates, MS Plate etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; nosing, framework of water tanks, band, straps, wind ties and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 26 | M&L for structural steel work as in truss, rafter purling, made out of angle / Hollow pipe / tube section including jointing cleats, plates flat iron, gusset plates, rails, braces etc. conforming to Fe 410-W (gde-E-250) Quality, confirming to IS-1161-1979 of grade St-240 complete all as specified and as directed. |
| 27 | Preparation of new steel surface and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed. |
| 28 | S&F in repairs 15mm size PVC connections with PTMT nuts of length 600mm, complete all as specified and directed. |
| 29 | S&F in repairs 15mm bore steel water tubes, 'medium grade', galvanised, with all fitting (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 30 | S&F in repairs 20mm bore steel water tubes, 'medium grade', galvanised, with all fitting (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 31 | M&L for Lagging to 20mm bore pipes used in external water supply or plumbing all around with 50mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25gauge 20mm mesh including applying with brushing neat cement slurry with 3 kg of cement per Sqm complete, complete all as specified and directed. |
| 32 | S&F in repairs 15mm bore bib tap, cast copper alloy, chromium plated, fancy type, long body with crutch or butterfly handle, screwed for iron pipe or for brass ferrule, complete all as specified and directed. |
| 33 | S&F in repairs 15mm dia Angle valve, cast copper alloy, chromium plated screwed down, high pressure screwed both ends for iron pipe or for union and fixed, complete all as specified and directed. |
| 34 | S&F in repairs Vitreous china squatting pan, Orissa pattern, size 580 x 440mm and making good, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., including trap set in and including concrete, complete all as specified and directed. |
| 35 | S&F in repairs 10 litre capacity PVC valveless, Syphonic action type, flushing cistern low level, white with inlet ball valve, float and handle including brackets and PVC flush pipe etc., complete all as specified and directed. |
| 36 | S&F in repairs vitreous china wash hand basin, white flat back, size of 550x400mm including cutting for and pinning in ends of brackets (including supply and fixing of brackets) or erecting stand, 32mm brass chromium plated waste fitting with long screwed shank and fly nut flangedend bedded in red led cement, chain and plug and porcelain stopper, complete all as specified and directed. |
| 37 | S&F in repairs vitreous China urinal half stall type, white, suitable for childrens with grating and union for discharge pipe and including waste pipe(excluding flushing cistern), complete including providing and fixing plugs,bedding urinal agaist wall in CM 1:2 securing urinals to plugs including 60 mm long brass screws including CP urinal spreader of any colour for fixing with 15 mm dia pipe (Minimum weight 60gms), complete all as specified and directed. |
| 38 | S&F in repairs looking mirror of size 600x450mm with PVC moulding, complete all as specified and directed. |
| 39 | S&F in repair 75mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp or laid in trenches, complete all as specified and as directed. |
| 40 | S&F in repair 110mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp or laid in trenches, complete all as specified and as directed. |
| 41 | S&F 100/75mm outlet PVC (SWR) floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), complete all as specified and directed. |
| 42 | S & F in repairs 110mm bore PVC (SWR) 'P’ trap complete all as specified and directed by Engineer-in-Charge. |
| 43 | S&F in repairs brass chromium plated tubular towel rail 20mm dia \\"D\\" type 60cm long between flanges, complete all as specified and directed. |
| 44 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed. |
| 45 | M&L for brick work with sub-class `B' bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed. |
| 46 | M&L for stone walling of random rubble masonry brought up to course, well bonded, bedded and solidly hearted built in CM 1:6, complete all as specified and directed. |
| 47 | All as per Ser item No 46.00 here in before but except stones. |
| 48 | M&L for plain cement concrete, 1:2:4, Type B-1 (using 20mm graded crushed stone aggregate) as in coping, hold fast, roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed. |
| 49 | M&L for plain cement concrete, 1:3:6, Type C-1 (using 20mm graded crushed stone aggregate) as in surface channel and drain including necessary form work, complete all as specified and as directed. |
| 50 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed. |
| 51 | M&L for rendering 15mm thick on other than fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed. |
| 52 | M&L for 15mm thick rendering on fair faces on brick or concrete surfaces in CM 1:4, fair finished the surfaces even and smooth without using extra cement including scaffolding upto 12m height, complete all as specified and directed. |
| 53 | Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting, on plastered surface preparatory to distempering , complete all as specified and directed. |
| 54 | Preparation of new surface of wall and applying two coats of cement based paint over one coat of primer including scaffolding up to 15m height, complete all as specified and directed. |
| 55 | Preparation of old plastered surfaces of wall by washing down, brooming down or steel wire brushing etc. and applying one coat cement base paint including scaffolding up to 15m height, complete all as specified and directed. |
| 56 | Preparation of old plastered surfaces of wall by washing down, brooming down or steel wire brushing etc. and applying two coat cement base paint including scaffolding up to 15m height, complete all as specified and directed. |
| 57 | Preparation of old decorated plastered or unplastered surfaces of wall including filling of holes, cracks and undulating surface with cement wall care putty making surface even and smooth and applying two coats of distemper oil emulsion paint (OBD), complete all as specified and directed |
| 58 | Preparation of old painted steel and iron surfaces of any description not otherwise described exc 10cm width or girth by brooming down or steel wire brushing, scrapping down, smoke soot moulds, moss and efflorescent salts and greasy spots of roof /CGI Sheets, steel gates, steel doors, steel rolling shutters, steel eves boards etc. and applying one coat of synthetic enamel paint including scaffolding up to 15m height, complete all as specified and directed. |
| 59 | Complete removal of existing treatment from wall surfaces and applying two coats of oil bound distemper of approved colour including applying 1mm thick JK Birla wall care putty for making the surface even and smooth and filling the uneven and small holes and making the edges of plaster properly by plaster of paris preparatory to distempering including preparation of surface by washing rubbing down and stopping of distempered surfaces, complete all as specified and directed. |
| 60 | S&F in repairs Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 61 | S&F in repairs Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 62 | S&F in repairs 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating, complete all as specified and directed. |
| 63 | All as per Ser item No 62.00 here in above but except Sheets. |
| 64 | S&F in repairs 0.63mm thick Galvanised, Plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating, complete all as specified and directed. |
| 65 | Preparing old zinc (or galvanised) surfaces to receive painting of any description over 10cm width or girth, by coating with mordant solution including washing and cleaning, etc. steel and iron surfaces and applying two coats of synthetic enamel paint in camouflaging CCD pattern as approved, complete all as specified and directed. |
| 66 | Preparing new zinc (or galvanised) surfaces to receive painting of any description over 10cm width or girth, by coating with mordant solution including washing and cleaning, etc. steel and iron surfaces and applying two coats of synthetic enamel paint in camouflaging CCD pattern as approved, complete all as specified and directed. |
| 67 | Demolition of old PQC / concrete of any description and in any position not other wise specifically provided for and demolished material thrown out of premises complete all as specified and directed by Engineer-in-Charge |
| 68 | M&L for 100mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 69 | M&L for plain quality concrete work in pavement / hard standing of flexural strength 40 kg / Sqcm2 in field using 400 kg of cement per cubic metre or as per design mix whichever is higher including using non circular synthetic polyster triangular fibre @ 0.25% by weight of cement, thickness of concrete 20 cm, complete all as specified and directed.Note:- (i) Unit rate quoted shall be inclussive steel formwork as required. |
| 70 | M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’, thickness of slab 15cm, complete all as specified and directed. |
| 71 | M&L for forming contraction (Dummy) joint, 65mm deep x 10mm wide as the work proceeds in alternative ways and filled with sealing compound grade 'A' after priming with primer for grade 'A' sealing compound , complete all as specified and directed. |
| 72 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 73 | M&L for 25mm thick plain cement concrete, 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base of floor finish even and rough to receive further floor finishes (tile/kota stone/ marble ), complete all as specified and directed. |
| 74 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 75 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 76 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile not exceeding 0.36 Sqm, as in skirting etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 77 | M&L for Glazed ceramic tile 450x 300 x 06-7mm thick (coloured) on vertical surfaces such as wall, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 78 | M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms with gas pipe hole, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including demolition of existing stone slab and tiles, complete all as specified and directed. |
| 79 | S&F in repairs 1.25mm thick of laths of steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple but gear operated type with bevel gear box and crank handle and one shop coat of primer, erected in position as indicated, push pull or manual type, complete all as specified and directed. |
| 80 | S&F in repairs 1.00mm thick of laths of steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, push pull or manual type, complete all as specified and directed. |
| 81 | Taking down the existing rolling shutters from the existing opening and refixing the same in position after carrying out necessary repairs including oiling, greasing,easing out etc size of shutter exc 7.00 Sqm and n exc 16.00 Sqm each. all as specified and directed. |
| 82 | M&L for greasing the bottom rail , repair of gap, making the sliding iron door of blastpen in technical area of size exc 30 sqm but n exc 60 sqm each after carrying out necessary repairs including oiling, greasing, easing out etc., complete all as specified and directed. |
| 83 | S&F in repairs hood cover made with 1mm thick MS sheet, made to hexagonal square or circular contour and stiffened with angle / flat stiffeners at top and bottom edges and fixed to bracket plate as existing, complete all as specified and directed. |
| 84 | S&F in repairs mild steel safety lever locks with 4 levers for rolling shutters size of lock 100mm, complete all as specified and directed. |
| 85 | S&F in repairs mild steel handle for rolling shutter of size 150mm, complete all as specified and directed. |
| 86 | S&F in repairs rolling shutter gear box made up of worm gear, worm wheel, motor count gearbox case and drive shaft including making the shutter in operating condition, complete all as specified and directed. |
| 87 | S&F in repairs fabricated lock plate of riveted construction made of mild steel sheet of not less than 3.15mm thick, reinforced with mild steel angle section of size 35x35x5mm size at the bottom, interlocked with bottom most lath section of curtain so as to provide contact against the cill, when closed, fitted with sliding bolts with arrangement for locking with pad locks, one handle for widths upto 2.5m, and two handles for widths of above 2.5m, complete all as specified and directed. |
| 88 | S&F in repairs 40mm dia mild steel pipe shaft, heavy duty, complete all as specified and directed. |
| 89 | M&L for Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets including taking down old, complete all as specified and directed. |
| 90 | M&L welding work for exc 2.5cm and n. exc 5cm in length, thickness of metal to be welded n exc 6mm, welding of hinges, helical door spring, tower bolt clips, MS Flat in steel window for fixing wiremesh etc., complete all as specified and direcetd. |
| 91 | M&L for mild steel works as in holdfast, rails, braces, etc., drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging holdfasts, Grills, cladding and similar small articles conforming to Fe 290 Gde E-165, in repairs, complete all as specified and directed. |
| 92 | S&F in repairs marathon mild steel wheel, Heavy duty, dia of wheel exc 200mm and n.exc 300mm and width of wheel exc 75mm and n.exc 100mm for hanger door load including fixing to existing or new MS plate of existing size, complete all as specified and as directed. |
| 93 | Taking down and refixing of hanger door of any size for fixing of wheels etc., complete all as specified and directed. |
| 94 | Demolition of cement concrete in ground floors and pavings n exc 15cm thick (below or above ground level), complete all as specified and directed. |
| 95 | M&L for 100mm thick plain cement concrete, 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in flooring , laid in alternate bays and finishing the surface even and smooth without using extra cement, complete all as specified and as directed. |
| 96 | M&L for 75mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 97 | M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and direction. |
| 98 | S&F chequered cement concrete tiles size 300 mm x 300 mm x 22-25mm thick with grey cement and pigment , rubber moulded glossy finish, ISI marked, coloured, set jointed and pointed in neat cement slurry over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 99 | Preparation of old decorated plastered or unplastered surfaces of wall including filling of holes, cracks and undulating surface with cement wall care putty making surface even and smooth and applying one coat of distemper oil emulsion paint (OBD), complete all as specified and directed |
| 100 | Preparation of old plastered or unplastered surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. including cornices, pilasters etc. and applying two coats of white (lime) wash, complete all as specified and directed. |
| 101 | Deduction to be made from BOQ for Schedule 'A' Part-II (Credit Schedule from dismantling / taking down items) worth Rs 1,98,250.00 during AOC.(Note :- Tenderers shall not quote for this Schedule) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysSep 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender