Tender For Special Repairs To Building No.P-283/1,2,5,6 (04 Or Md Accn) And Provision And Installation Of 20 X Monkey Caging For Roof Top Water Tanks Of Jcos/Or Md Accn Of 617 (I) Ad Bde Signal Coy C Under Ge (A) Baroda.
Tender Value
42.11 Lakhs
Estimated cost
Bid Submission
01 Sep 2026
8 days left
EMD
84220
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Vadodara → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Building No.P-283/1,2,5,6 (04 Or Md Accn) And Provision And Installation Of 20 X Monkey Caging For Roof Top Water Tanks Of Jcos/Or Md Accn Of 617 (I) Ad Bde Signal Coy C Under Ge (A) Baroda.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar. |
| 2 | Roughening of old unservicable PCC floor surface by picking, chipping and wire brush sweeping clean and washing down with water to remove dust outside to make it suitable for laying floor tile complete all as specified. |
| 3 | M&L for non skid coloured ceramic tile 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge) |
| 4 | M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile joint free exceeding 0.18 sqm but not exceeding 0.38 sqm , as in floors etc set over and including high performence adhesive manufactured by somani ezifix tile adhesive or equivalent mixed in cement as per manufacturer instruction and jointed with polymer modified cementetious grout manufactured by somani ezy grout or equivalent of pigment matching to tile color including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 (Tile pattern and decoration may be as suggested by Engineer-in-charge) |
| 5 | M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , as in skirting etc set over and including 10 mm thick rendering with CM 1:3 including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge) |
| 6 | M & L for Glazed ceramic coloured walls tiles in vertical surfaces 300x450x 6mm to 7 mm thick set over and including 10mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:3 to receive wall tiles including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge). |
| 7 | M & L for 18 to 20 mm thick machine cut green marbel stone in single piece as in steps, landings, jambs, pillars, window cills, and like laid over cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10 mm thick plastering with cement mortar 1 : 3 including necessary adhesive complete all as specified |
| 8 | M & L Granite (of any type and colour) work (table rubbed and polished) 18mm-20 mm thick in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and directed. |
| 9 | M & L for machine cut kota stone slab in kitchen platform,tread ,floor etc. of 20 - 25mm thick (the stone may be in one piece) including rubbing and polishing complete set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 |
| 10 | M & L for machine cut kota stone riser,skirting etc. of 20 - 25mm thick (the stone may be in one piece) including rubbing and polishing complete set over and including backing coat of 10mm in cm 1: 3 |
| 11 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each |
| 12 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) Exc 1.5 Sq m but n.exc 4.00 Sq m each |
| 13 | M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type 1.0mm thick (veneered on both side) with decorative choice laminated type 1 (factory laminated), or surface finish, 6mm thick or external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE. |
| 14 | S & F 35mm thick 2nd class Hard wood Glazed and Skeleton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats. |
| 15 | S&F of Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 16 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 17 | S&F 4.00mm+/-0.20mm thick tinted glass of bronze colour , selected ordinary quality and glazing with rubber beading or with glazing clips exc 0.5 sq. m in each pane as per instructions of manufacturers, all as specified and directed. |
| 18 | S&F 4.00mm +/-0.20mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips n exc 0.5, all as specified and directed. |
| 19 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples. |
| 20 | S & F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolt, if required hooks (stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps hold fasts, wall ties, hooks for hanging fans, plain angles cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe 310-O or Fe 410-O |
| 21 | M & L Cement concrete type B1, 1:2:4 (20 mm graded stone aggregate) as in coping, bed plate for hold fast etc. |
| 22 | M&L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC door frame with screw complete all as specified and directed. |
| 23 | M&L for 75mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC door frame with screw complete all as specified and directed. |
| 24 | S & F 200mm long Aluminium anodised barrel tower bolt of extruded section and fixed |
| 25 | S & F 150 mm size extruded aluminium alloy handles, fabricated type anodised |
| 26 | S & F aluminium anodised Hasp and staple, safety type of size 75 mm with mild steel hinge pin including bolt to hinge plate and fixed with screws |
| 27 | S & F 250 mm aluminium alloy anodised sliding door bolts, with hasp and staple (bolt type) not less than 12mm dia with and and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium and fixed to wooden door shutters |
| 28 | S & F SS W Hinges SS 202 Grade steel Rust Resistance , for fixing cup boords shutters sizes of hinges 3\\" to 4\\" and 1.5 mm thickness, suitable for 18 mm thick cabinets shutters complete all as specified and directed |
| 29 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). ®Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed. |
| 30 | S&F Factory made single extruded WPC (Wood PolymerComposite) solid plain flush door shutter of 30mm sizecomprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural Fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately complete all as specified and directed. |
| 31 | Dismantling of board of any description fixed in any postion with nails |
| 32 | S&F 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century. |
| 33 | S&F 18mm thick HDHMR BOARD exterior grade including white coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century. |
| 34 | S & F 150mm aluminium anodised barrel tower bolts of extruded section and fixed. |
| 35 | S & F tubular curtain rails 25mm dia stainless steel 202 grade drapery type complete all as specified directed |
| 36 | S & F in repairs stainless steel socket fancy type with bracket for 25mm dia stainless steel tubular curtain rod (design of socket shall be approved by GE/AGE at the time of execution) as directed |
| 37 | S & F in repairs 20mm dia brass chromium plated tubular towel rail complete. |
| 38 | S & F for mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete |
| 39 | M & L mild steel for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework (caging) of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed |
| 40 | M & L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 41 | M & L for preparing new steel surface of any description not otherwise described n. exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 42 | M & L for preparing new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. |
| 43 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge. |
| 44 | S & F 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed |
| 45 | S&F in repair stainless steel cabinet/drawers handle having a length of 100mm and shape all as specified and directed. |
| 46 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge. |
| 47 | S & F 20mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed. |
| 48 | Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed by Engr-in-Charge. |
| 49 | S & F 25mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed. |
| 50 | S & F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed. |
| 51 | S & F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed. |
| 52 | S & F in repairs 110mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 53 | S & F in repairs 110mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed. |
| 54 | S & F in repairs 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed. |
| 55 | S & F in repairs 75mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 56 | S & F in repairs 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed. |
| 57 | S & F in repair 75mm PVC (SWR) floor trap, plain with CP grating including jointing with solvent all as specified and as directed. |
| 58 | S & F in repairs 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed |
| 59 | S & F in repairs 75mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed |
| 60 | S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed |
| 61 | S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 75mm bore pipe all as specified and as directed |
| 62 | S & F 110mm PVC (SWR) vent cowl all as specified and as directed |
| 63 | S & F 75mm PVC (SWR) vent cowl all as specified and as directed |
| 64 | S & F in repairs 15mm bore chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule |
| 65 | S & F CP wall mixer three in one system for mixing hot and cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and directed. |
| 66 | S & F in repairs stop valves/Angle valve15mm bore fancy type chromium plated screwed both ends for iron pipe or for unions and fixed |
| 67 | S&F in repairs stop valves/angle cocks or two way angle cock fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for 15mm bore iron pipe or for unions and fixed complete all as specified and directed. |
| 68 | S & F in repairs 25mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed |
| 69 | S & F in repairs 20mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed |
| 70 | S & F in repairs 125mm dia chromium plated shower rose with swivel joints including fixing to steel pipe or GI union complete |
| 71 | S&F 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/cm2 as in waste pipe |
| 72 | Dismantling of water storage tank of 500 ltrs capacity. |
| 73 | S & F 1000 Ltrs Rotational moulded polyethylene water storage tanks three layered with tank adapter (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I |
| 74 | S & F in repairs Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule and fixed |
| 75 | S&F in repair Vitreous China wash down water closet pan (Europion pattern), white (excluding fixing bolts, flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor. complete all as specified and as directed. |
| 76 | S&F in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 77 | S&F in repairs Vitreous China wash down water closet (Squat pattern ) white complete as fixed in repair excluding flushing cisternand flush type \\"Orrisa\\" pattern size 580x440 with integral footrest inject connection to trap antisyphonage etc complete including joint between flushing pipe and socket of WC. |
| 78 | S&F in repairs PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band (flush pipe) 32mm complete all as specified. |
| 79 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 80 | S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed. |
| 81 | S & F 110mm PVC (SWR) WC connector bent type to fit WC outlet all as specified and as directed. |
| 82 | S & F 110mm PVC (SWR) junction single, (Single T) equal or unequal all as specified and as directed. |
| 83 | S & F 75mm PVC (SWR) junction single, (Singlet T) equal or unequal all as specified and as directed. |
| 84 | S & F in repair vitreous china Wash hand basin,white, table top, size 550x400 mm except taps, CP waste coupling all as specified. |
| 85 | S&F in repair brass CP centre hole basin mixer for mixing hot & cold water three way screwed down for iron pipe 15mm bore and fixed complete. |
| 86 | S & F 32 mm dia stainless steel waste coupling for wash hand basin all as specified and directed. Make : Prayag or equivalant. |
| 87 | S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm |
| 88 | S&F in repairs 350x450mm size cabinet mirror rectangular shape with 4mm thick selected quality mirror and PTMT frame with openable door shutter with PTMT frame outside mirror as complete. |
| 89 | S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever bracket and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 90 | Supply & Fix of stainless steel wall mounted plate rack of size 750x900X 250 mm and thickness of sheet not less than 0.50mm with provn for keeping plates and other crockery fixed with screw and rawal plug etc on wall complete all as specified and as directed |
| 91 | Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work |
| 92 | M&L Cement concrete type B1 1:2:4 (20 mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges. |
| 93 | Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc. |
| 94 | Demolition brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc, |
| 95 | M&L Brickwork with fly ash ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 |
| 96 | S&F 40mm bore UPVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe |
| 97 | M & L Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement) |
| 98 | M&L Rendering in two layer on fair faces of brick work or concrete sur-faces of wall 5 mm thick in CM 1:4 mixed with WPC as per manufacturers instructiion for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 (WPC will be measured and paid separately). Note:-Rate of WPC shall be deemed to inclued in quoted rates. |
| 99 | M&L Rendering 5 mm thick on fair faces of brick work or concrete sur-faces of ceiling in cement mortar 1:3 for finished even and smooth (without using extra cement) |
| 100 | M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of 2mm average thickness birla/ equivalent wall care putty and one coat of primer all as specified and as directed. |
| 101 | M& L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 102 | M & L for preparing new plastered surfaces of ceiling and applying three coats of white wash. |
| 103 | M & L for Complete removal of exiting treatment from wall and preparation of old surfaces of wall and applying two coats of oil bound distemper over and including a coat of 2mm average thickness birla/ equivalent wall care putty and one coat of primer all as specified and as directed. |
| 104 | M& L for Complete removal of exiting treatment from wall and preparation of old surfaces and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 105 | M & L for Complete removal of exiting treatment from ceiling and preparation of old surfaces of ceiling and applying two coats of white wash. |
| 106 | M & L for complete removal of loose / cracked concrete incl reinforcement if required, from RCC roof projection,chajja,fins,facia, roof bands etc and making good with PCC (1:11/2; :3) type A0 (using 12.5 mm graded stone aggregate) in any slab and in any position finished the surface even and smooth with out using extra cement including necessary form work and welding/binding of reinforcement (including reinforcement) if required complete and applying three coat of white wash/two coat of cement base pint to match with the existing surface as directed by the Engr- in -Charge . (Reiforcement will be measured and paid saperately under respective item. |
| 107 | M&L for Providing precast cement concrete Type B1, 1:2::4 (using 20 mm Aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to matchcomplete all as specified and directed. (reinforcement shall be measured and paid separately) |
| 108 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specifed and as directed. |
| 109 | Demolition of existing PCC/lean concrete including floor tiles and removing rubbish off the premises. |
| 110 | M&L for 15 mm thick plaster in sunken portion with CM 1:3 mixed with liquid water proofing compound as per manufacturers instruction and should be even and smooth without using extra cement all as directed. Note . (WPC will be measured and paid separately). |
| 111 | M&L for providing & laying applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum 75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed as per manufacturer instructions complete all as specified and as directed. |
| 112 | M&L for sunken portion filled with lean concrete 1:5:10 using brick/lime aggregate and finish the surfaces rough to receive sub base complete all as specified and as directed. |
| 113 | M & L for 25 mm thick cement concrete in flooring type Bo, 1:2:4 (12.5mm graded aggregate) with liquid water proofing compound as per manufacturers instructions for laying floor tiles. Note (Rate of WPC shall be deemed to inclued in quoted rates). |
| 114 | S& F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed. |
| 115 | Demolition of cement concrete of any description and in any position not otherwise specifically provided. |
| 116 | M & L for 75 mm thick PCC 1:3:6 mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement. |
| 117 | S&F in repairs grating 150mmx150mm made out of stainless steel complete all as specified and directed. |
| 118 | S&F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed. |
| 119 | S&F magnet door stopper of rectangular size for PVC cabinets including all fittings fixed complete all as specified and directed. |
| 120 | M & L for ATT work by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area |
| 121 | M & L for ATT work by treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors |
| 122 | S & F in repairs brass chromium plated towel ring of PTMT complete. |
| 123 | S&F in repairs CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed. Make : Prayag & equivalent |
| 124 | Polishing of old existing Kota stone flooring i.e, cutting , grinding, joints pigment filling and polishing to get mirror finish all as specified and directed. |
| 125 | Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc.15 cm thickness (below or above ground level) and removing from site all as specified and directed. |
| 126 | M & L for 75 mm thick PCC 1:3:6 mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement. |
| 127 | M&L for factory made precast machine pressed kerb stones of PCC grade M-15 design mix and of shape and size rected, set jointed and pointed cement and sand mortar 1:4 fixed in repairs with and including necessary excavation and earthwork and making good the disturbed surfaces to match with the existing surfaces including removal of dispodal of rubbish complete all as specified and directed. Sizes shall be as under :- Length (L) not less than 300mm, Height (H) 300mm to 350mm, Thickness (T) 100mm and radius (R) 75mm including painting on kerb stone of synthetic enamel paint yellow or white colour complete all as specified and directed. |
| 128 | M & L for Hard core gauge not exc. 63mm of broken bricks diposited spread and levelled in layers not exc. 15 cm watered and rammed to a true surface complete all as specified. |
| 129 | M&L Sand Filling a layer of 50mm thick sand cushioning including filling the joints with sand as in floors/ paths including watering and consolidation complete all as specified and directed. |
| 130 | Material and labour for 60 mm thick, machine made ,1st quality, precast cement concrete rubber moulded coloured interlocking paver blocks , of triangular / Zigzag / Haxagone/ I , in shape or shap and design as approved, with grey cement and pigment , having M-35 Grade and conforming to IS 15658-2006 specifications , complete all as specified and directed. |
| 131 | M&LFramed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steelsheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed |
| 132 | M&L for Hard drawn steel wire fabric made up of wire having min dia 2 mm weight per square meter not exc 4.0 kg, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt, complete all as specified and directed. |
| 133 | S & F anti heat insulation climate protect water thermal tank cover / jacket for Hot & Cold wheather for 1000Ltr water tank. The cover should be environmental friendly made with 5 layers heavy duty nylon velcro straps belt for tighten the tank and made of supportive forming technology complete all as specified and directed. |
| 134 | Taking down carefully existing unserviceable copper/aluminium point wiring (light, fan, socket or power point etc) complete with fittings/fixures such as switches sockets, ceiling rose, fan regulators, etc ( except tube light fittings), removing materials for taking credit and making good disturbed surface of wall, floors, etc complete all as directed by Eng-in-Charge. |
| 135 | Taking down main switch, DB/change over/VTPN, MCCB AC box of any capacity. |
| 136 | M&L for concealed point wiring with 1.5 Sqmm PVC-FRLSH insulated, unsheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit of size not less than 20mm ISI marked ivory white With all accessories, including modular metal flush boxes & modular white cover plate of suitable module with frame as per site requirement all fittings such as tees, bends, elbows, etc. all as per site requirements PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green all as directed by Engr-in-charge . |
| 137 | One light point controlled by one switch. |
| 138 | One ceiling fan point controlled by one switch and fan regulator. |
| 139 | One exhaust fan point controlled by one switch. |
| 140 | One bell point controlled by one bell push |
| 141 | One 3 pin socket outlet 5 Amps independent board. |
| 142 | One 3 pin socket outlet 5 Amps on the same board with other switch. |
| 143 | One light point controlled by two Nos two way switches |
| 144 | All as per item No. 136 here-inbefore but with 2.5 sqmm PVC insulated multistranded flexible unsheathed copper conductor inclusive of 2.5 sqmm PVC insulated multistranded flexible copper conductor for one independent 6 pin 16 Amp socket. |
| 145 | S&F Modular switch, one way,6 Amp 230, 1 module . |
| 146 | S&F Modular switch, two way, 6 Amp 230, 1 module. |
| 147 | S&F Modular bell push 6A one module . |
| 148 | S&F Modular switch, one way,6 A/16 Amp 230, 1 module . |
| 149 | S&F modular socket 6 Amp-2/3 pin combined 2 module . |
| 150 | S&F modular socket 6 A/16-2/3 pin combined 2 module . |
| 151 | S & F ceiling rose surface polycarbonate body three terminal. |
| 152 | S & F lamp holder, Polycarbonate type with back plate for batten fitting including 9 watt LED lamp complete all as specified and directed |
| 153 | S & F of ceiling fan complete with blades, down rod from existing roof / trus to fall ceiling, electronic regulator and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV ceiling fan complete all as specified and directed.Note : 1) Old ceiling fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 154 | S & F for Bell, AC, 230 volts, single pole complete all as specified and directed |
| 155 | Taking down & Refixing the same after repairing work of B/R & E/M electric water heater, storage type, steel inner tank and heating element upto 2 KW capacity 25 litre connection pipe etc complete all as specified and directed |
| 156 | Supply and fixing LED batten lights fitting made of Aluminium extrusion 1x 20W (4 feet) , input voltage 140-270 V AC,CCT 6500K, Lumin efficency 100 lm/watt ,surge protection upto 4KV , Voltage protection upto 440 V AC.PF >0.9 , connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr -in -charge. Including Taking down old Tublight fittingsNote :-Warrenty on light should be of minimum 02 Years provided by the contractor. |
| 157 | Supply and fixing LED light fitting made of Aluminium extrusion mirror type with high out put diffuser 1x10 watt 2 feet , input voltage 140-270 V AC,CCT 6500K, Lumin efficency 100 lm/watt ,surge protection upto 4KV , Voltage protection upto 440 V AC.PF >0.9 with driver including connecting up with flexible copper conductor cable of suitable size complete all as specified and directed by Engr in charge.Make Havells LUMILINEPLUSPROBS10WLED865SPCSSIND/Bajaj BCLSB 10 W WHNote Warrenty on light should be of minimum 02 Years provided bythe contractor. |
| 158 | Taking down & S & F of exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers, 50Hz, RPM 1200, copper winding of sweep 300mm including cutting of suitable size holes on existing wall and making good disturbed work to match the existing surfaces and exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directedNote : 1) Old exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 159 | Taking down & S & F of exhaust fan , plastic body AC single Phase. 230V of size 250mm sweep with, blades, and frame and louvers, 50Hz, RPM 1200, copper winding of sweep 250mm including cutting of suitable size holes on existing wall and making good disturbed work to match the existing surfaces and exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directedNote : 1) Old exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 160 | S & F Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 6.0 Sqmm size drawn through and including not less than 25 mm dia PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends fixed to the surface of wall/ceiling including one run of 6.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor.NOTE : Two runs of single core 6.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length. |
| 161 | S & F sheet metal enclosures (double door) for DBs where MCBs to be used Triple pole and neutral 4 way 240 V with 200 amps rated bus bar fixed on wall complete with all acessories complete all as specified and directed |
| 162 | S & F sheet metal enclosures (double door) for DBs where MCBs to be used single pole and neutral 8 way 240 V with 200 amps rated bus bar fixed on wall complete with all acessories complete all as specified and directed |
| 163 | S & F MCB single pole, having rupturing 10KA, 6 amps to 32 amps as ordered 240 Volts |
| 164 | S & F MCB Single pole and neutral (SPN), having rupturing 10KA, 240 V 63 amps as ordered. |
| 165 | S & F MCB Triple pole and neutral (TPN), having rupturing 10KA, 240/415 V 63 amps as ordered. |
| 166 | Taking down and Refixing electronic meters above 25 Amp complete all as specified and directed |
| 167 | Supply & Fix building security light of 35 Watt LED Street Light fitting New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP OPENING seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device ,lumens should be ≥ 120 lm/w ,OEM driver,PF 0.9,CCT 5700K including bracket made out of GI pipe light grade 32mm bore not less than 1.20m long bent to shape required fixed to pole with suitable size 2 Nos clamps made out of 25X3mm flat iron with nut, bolts and washers complete complete all as specified and directedNote :- The warranty on light should be of minnimum 2 Years provided by the contractor. |
| 168 | Earthing Complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.5 metre below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connection by using galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and other end of the earth wire connected to main switch board protected by galvanised iron medium grade pipe 40mm bore in wall/floor/and GI Pipe 20 mm bore light grade for watering with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC pit cover including necessary excavation and earth work in any type of soil, returning slurry approved soil and disposed of surplus soil to a distance not exceeding 50 Mtr away all as shown in electrical plate No 3 of SSR 2009 ( Part-I).Notes (a) The unit rate shall include for GI protection pipe, GI watering pipe, wire mesh, funnel and excavation, RCC pit cover, test point, galvanised iron strip from top of earth plate upto 7.5 metres above ground level and if GI protection pipe is less than 7.5 metres, no price adjustment shall be made.(b) PCC pit shall be provided at least 50cm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junction, elbow etc shall be deemed to be included in the unit rate.(c) If the testing result of earthing is not found below 5 Ω then the contractor shall do another earthing work at his own cost and nothing shall be permissible on this account.(d) Earthing work will be carried out in presence of MES representative. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysSep 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender