Tender For Repair To Certain Types Of Wooden And Steel Furniture, Chair Verandah, Charpoy Ip Hard Top At At Icgs Vijay Nagar, Panchu Tikrey Under Age B/R (P) Hut Bay
Tender Value
4 Lakhs
Estimated cost
Bid Submission
02 Sep 2026
16 days left
EMD
8000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Certain Types Of Wooden And Steel Furniture, Chair Verandah, Charpoy Ip Hard Top At At Icgs Vijay Nagar, Panchu Tikrey Under Age B/R (P) Hut Bay
BOQ
| Sl. No. | Item Description |
| 1 | NOTE: 1. The bidders/ contractors are advised to read tender documentts and all corrigendum/ amendments and General conditions of contracts before entry/ quoting the rates. 2. It is highlighted that the certain condition of General condition of contracts (IAFW- 2249) has been modified as direction of MOD i.e inclusion of performance security, deletion of risk & cost provisions and increase in defect liability period all as specified in tender document. |
| 2 | BED HARD Steel with P/Top (FD/E6/MAP/08 (R))S&F 12mm thick plywood BWR Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitable screws wood/steel including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge. |
| 3 | S&F in repairs to head boards made out of Prelaminated Particle Board exteriro grade with 4 mm thick teakwood beading all-around as per existing size of Bed including removal of damaged board rest all as specified on drawing or as directed by Engineer-in-charge |
| 4 | S&F in repairs to foot boards made out of Prelaminated Particle Board exteriro grade with 4 mm thick teakwood beading all-around as per existing size of Bed including removal of damaged board rest all as specified on drawing or as directed by Engineer-in-charge |
| 5 | Hard Rubber/PVC Shoe of superior quality (Set of four, each set will be measured as one) as approved & as directed by Engr-in-charge. |
| 6 | Removal of existing worn out paint and Re-Painting to the entire frame of Charpoy MS P/Top with Black colour synthetic enamel paint over a coat of primer of approved make rest all specified on drawing or as directed by Engineer-in-charge. |
| 7 | Chair Verandah (FD-259/359/FD/MAP-II/06)Welding joints of broken leg of 19/20mm MS tube & other joints as per drg complete all as shown on drg and as directed by Engineer-in-charge. |
| 8 | Hard PVC/Nylon shoes as per drg complete all as shown on drg and as directed by Engineer-in-charge. |
| 9 | S & F in repairs PVC Seat and Back with approved make complete all as shown on drg and as directed by Engineer-in-charge. |
| 10 | Removal of existing worn out paint and Re-Painting to the entire frame of chair verandah with white colour synthetic enamel paint over a coat of primer of approve make all specified on drawing or as directed by Engineer-in-charge. |
| 11 | CHAIR TUBULAR STEEL WITH ARMS (FD-75 (M))Repairs/ replacement of seat frame made out of superior quality hard wood 35x25mm size duly black painted and caned Godrej pattern for tubular steel chair CB with arms of overall size of seat frame 450x450mm, complete all as shown on drg and as directed by Engineer-in-charge. |
| 12 | Repairs/ replacement of back rest frame made out of superior quality hard wood 35x25mm size duly black painted and caned Godrej pattern for tubular steel chair CB with arms of overall size of seat frame 450x380mm complete all as shown on drg and as directed by Engineer-in-charge. |
| 13 | Replacement of hand rest (Godrej pattern) duly painted with black enamel paint as per existing size for tubular steel chair tubler steel with arms complete all as shown on drg and as directed by Engineer-in-charge. |
| 14 | Repair/replacement of Flat iron strips 20mm x 3mm, two in numbers in each seat and back, shall be welded to frame of chair, complete all as shown on drg and as directed by Engineer-in-charge. |
| 15 | Removal of existing worn out paint and Re-Painting to the entire frame of chair CB with smoke grey colour synthetic enamel paint over a coat of primer of approve make all specified on drawing or as directed by Engineer-in-charge. |
| 16 | CHARPOY MS WITH PLYWOOD TOP (FD/MAP-II/01/388(R))S&F in repairs to 12mm thick plywood BWR Grade, single piece of approved quality with suitable steel screw and cup washer including removal of damaged plywood, rest all as shown on drg and as directed by Engr-in-Charge. |
| 17 | Repair/replacement of damaged stiffners of suitable size duly welded to long rails as shown in drg |
| 18 | Hard Rubber/PVC Shoe of superior quality (Set of four, each set will be measured as one) as approved & as directed by Engr-in-charge. |
| 19 | Removal of existing worn out paint and Re-Painting to the entire frame of Charpoy MS P/Top with Black colour synthetic enamel paint over a coat of primer of approved make rest all specified on drawing or as directed by Engineer-in-charge. |
| 20 | Table Bed side MAP (FD/E6/MAP/15( R))M&L for removing paint by scraping down old paint carrying out repair such as removing the dents and welding wherever required and applying two coats of synthetic enamelled paint black colour over a coat of primer after preparation of surfaced,complete all as shown on drg and as directed by Engineer-in-charge. |
| 21 | Removing of existing unserviceable side of Table Bed Side and providing new sides of 18mm thick prelaminated Particle Board with OST and balancing white on the other side of exterior grade, rest all as specified on drawing or as directed by Engineer-in-charge. |
| 22 | Replacement of existing unserviceable table top for Table bed side steel MAP made out of 18mm thick prelaminated particle board exterior grade with suitable PVC edging al-round top of table, complete all as shown on drg and as directed by Engineer-in-charge. |
| 23 | Removing the existing unserviceable Top drawer and providing New drawer made out of 18 mm thick Particle board on both sides and 6 mm thick BWR ply on bottom and back side, all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 24 | Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer made out of 18 mm thick Prelaminated Particle board on both sides and 6 mm thick BWR ply on bottom and back side, all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. (Note : Each drawer will be measured as single unit) |
| 25 | Removing of existing unserviceable side of Table Bed Side and providing new sides of 18mm thick prelaminated Particle Board with OST and balancing white on the other side of exterior grade, rest all as specified on drawing or as directed by Engineer-in-charge. |
| 26 | Removing of existing unserviceable Back of Table Bed Side and providing new Back of 6mm plywood BWR Grade shall be fixed with headless nail, rest all as shown on drg and as directed by Engr-in-Charge. |
| 27 | S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one |
| 28 | Teapoy Verandah (FD/E6/MAP/17)M & L for welding of broken joints of Teapoy varandah including preparation of surface and applying two coat of black synthetic enamel paint over a coat of red oxide primer complete, complete all as shown on drg and as directed by Engineer-in-charge. |
| 29 | Replacement of existing unserviceable table top for Teapoy verandah MAP made out of 18mm thick pre laminated Particle board teak finish on top and balancing white with on the other and all the four edges provided with suitable PVC beading complete all as shown on drg and as directed by Engineer-in-charge. |
| 30 | Removal of existing worn out paint and Re-Painting to the entire frame of chair verandah with black colour synthetic enamel paint over a coat of primer of approve make complete all as shown on drg and as directed by Engineer-in-charge. |
| 31 | S&F of mesh as per drg |
| 32 | S&F PVC buffer shoes to legs of suitable size and shape all as per drg. |
| 33 | Table Computer (FD/E6/MAP/03)Removing the existing unserviceable top of Table Computer and providing new top made out of 18mm thick prelaminated Particle board exterior grade OST face and other side balancing white all as specified on drawing or as directed by Engineer-in-charge. |
| 34 | Removing the existing unserviceable telescopic channel of Key Board and replacing with 16\\" long new telescopic channel, all as specified on drawing or as directed by Engineer-in-charge. |
| 35 | Removal of existing worn out paint and Re-Painting to the entire frame of Table Computerwith black colour synthetic enamel paint over a coat of primer of approve make complete all as shown on drg and as directed by Engineer-in-charge. |
| 36 | CHAIR DINING PVC Seat (FD/MAP-II/05)Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 30x55x890 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 37 | Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 30x55x460mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 38 | Removing the existing unserviceable back rest and proving new Teak wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 39 | Removing the existing unserviceable front rail and providing new Teak wood front rail of size 30x65mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 40 | Removing the existing unserviceable rear rail of size and proving new Teak wood rear rail complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 41 | Removing the existing unserviceable side rails and providing new Teak wood side rails of size 30x65 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 42 | Removing the existing unserviceable PVC seat and providing new PVC seat of approved make complete rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 43 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. for the following furniture articles:- |
| 44 | S&F Hard PVC/rubber shoes of superior quality duly fixed using screw of suitable size (Set of four, each set will be measured as one) as specified and as directed by Engr-in-charge. |
| 45 | CHAIR WRITING (530MMx470MMx890MM) (FD-280 )Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 55x30x890mm complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 46 | Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 55x30x660mm complete all as specified on drawingall as specified on drawing and as directed by Engineer-in-charge. |
| 47 | Removing the existing unserviceable back rest and providing new Teak wood back rest of size 50 x 15mm slightly curved made out of 50x35mm complete all as specified on drawingall as specified on drawing and as directed by Engineer-in-charge. |
| 48 | Removing the existing unserviceable front rail and providing new Teak wood front rail of size 30x65mm including drilling holes at @ 12.5 mm C/C complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 49 | Removing the existing unserviceable rear rail and providing new Teak wood rear rail of size 30x65mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 50 | Removing the existing unserviceable side rails and providing new Teak wood side rails of size 30x65mm including drilling holes @ 12.5mm C/C complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 51 | Removing the existing unserviceable broken arm rest of size 60x25 mm and providing new Teak wood arm rest complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 52 | Recaning of repaired chair writing with best quality of approved plastic cane 1.80 x0.46mm cane and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing and as directed by Engineer-in-charge. |
| 53 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing and as directed by Engineer-in-charge. |
| 54 | CHAIR DINING OFFICERS (FD/MAP-II/04)Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 30x55x890 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 55 | Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 30x55x460mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 56 | Removing the existing unserviceable back rest and proving new Padauk wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 57 | Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 30x65x420mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 58 | Removing the existing unserviceable rear rail of size and proving new Padauk wood rear rail 30x65x460mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 59 | Removing the existing unserviceable side rails and providing new Padauk wood side rails of size 30x65 x430mm complete all as specified on drawing or as directed by Engineer-in-charge. |
| 60 | Removing the existing unserviceable fabric leatherite seat and cushion providing new fabric seat and cushion 460mmx75 mm thick 40 mm density foam cover with fabric seat and 12 mm BWP ply wood, the cost of fabric should not be less than Rs 800 per meter sall as specified on drawing or as directed by Engineer-in-charge |
| 61 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 62 | S&F Hard PVC/rubber shoes of superior quality duly fixed using screw of suitable size as specified and as directed by Engr-in-charge. |
| 63 | CHAIR EASY (FD-229)Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 55x25 mm complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 64 | Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 50x25mm complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 65 | Removing the existing unserviceable broken arm rest and providing new Padauk wood arm rest of size 65x25x610mm complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 66 | Removing the existing unserviceable front frame and providing new Padauk wood front frame of size 55x25 mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 67 | Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 50x25 mm complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 68 | Removing the existing unserviceable rear rails and providing new Padauk wood rear rails of size 50x25mm complete all as specified on drawing all as specified on drawing and as directed by Engineer-in-charge. |
| 69 | Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 1.80 x 0.46 mm cane and border with 3x0.60 mm cane completeall as specified on drawing and as directed by Engineer-in-charge. |
| 70 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing and as directed by Engineer-in-charge. |
| 71 | COMMON FOR ALL CHAIRS (FD-228/ 279/280/225/285 or similar MAP Drgs)Removing the existing unserviceable stiffeners and providing new Padauk wood 2nd class hard wood stiffeners of size 25x20 mm . M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing and as directed by Engineer-in-charge. |
| 72 | PEG TABLE (300x350x450mm) (FD-277)M & L for removing the existing unserviceable leg and providing with new Padauk wood rear leg complete all as specified on drawing and as directed by Engineer-in-charge. |
| 73 | M & L for removing the existing unserviceable top rail and providing with new Padauk wood top rail complete all as specified on drawing and as directed by Engineer-in-charge. |
| 74 | M & L for removing the existing unserviceable bottom stiffiner and providing with new Padauk wood bottom stiffiner complete all as specified on drawing and as directed by Engineer-in-charge. |
| 75 | S&F Hard PVC/rubber shoes of superior quality duly fixed using screw of suitable size as specified and as directed by Engr-in-charge. |
| 76 | Replacement of unserviceable top prelaminated partical board exterior grade all as specified on drawing and as directed by Engineer-in-charge. |
| 77 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing and as directed by Engineer-in-charge. |
| 78 | TABLE DINING 6 PERSONS (FD-273/FD/MAP-II/03)S&F in repairs to unserviceable damaged legs from Table dining 6 persons made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge. |
| 79 | S&F in repairs to unserviceable damaged side short rails from Table dining 6 persons made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge. |
| 80 | Replacement of existing unserviceable table top for Table dining 6 persons made out of prelaminated particle board 18mm thick with one side teak facing and balancing white on the other side and fixed with 18x12mm wooden beading (Padauk) on all the four sides all as specified on drawing and as directed by Engineer-in-charge. |
| 81 | S&F in repairs to unserviceable damaged long rails from Table dining 6 persons made out of hard wood (Padauk) , all as specified on drawing and as directed by Engineer-in-charge. |
| 82 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing and as directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender