Tender For Special Repairs To Bldg No.P-89 (Single Offrs Accn) And Provision Of 1 X Toilet At Bldg No.P-137(Jcos Club & 1 X Toilet At Bldg No.P-325 (Regt Hq Complex) Of Ad Regt At Sector ‘C Makarpura Under Ge (A) Baroda.
Tender Value
32.47 Lakhs
Estimated cost
Bid Submission
08 Sep 2026
6 days left
EMD
64940
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Vadodara → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Bldg No.P-89 (Single Offrs Accn) And Provision Of 1 X Toilet At Bldg No.P-137(Jcos Club & 1 X Toilet At Bldg No.P-325 (Regt Hq Complex) Of Ad Regt At Sector ‘C Makarpura Under Ge (A) Baroda.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 01-Sep-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 08-Sep-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar. |
| 2 | M&L for Virified Ceramic tiles 9 to 10 mm thick any type of shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat 15 mm thick screed bed in CM 1:6 |
| 3 | M&L for Virified Ceramic tiles 9 to 10 mm thick any type of shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat 10 mm thick in CM 1:4 |
| 4 | M&L for non skid coloured ceramic tile 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge) |
| 5 | M & L for Glazed ceramic coloured walls tiles in vertical surfaces 300x450x 6mm to 7 mm thick set over and including 10 mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles including necessary adhesive (Tile pattern and decoration as approved by Engineer-in-charge). |
| 6 | Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc.15 cm thickness (below or above ground level) and removing from site all as specified and directed. |
| 7 | M&L for 18 to 20 mm thick machine cut green marbel stone in single piece in window/opening(jambs/cills) laid over cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10 mm thick plastering with cement mortar 1:3 including necessary adhesive complete all as specified |
| 8 | M & L for machine cut kota stone slab 12 - 15mm thick on vertcle sufaces steps, skirting , and dado of over 10 mm thick plaster in cement mortar in 1:4 jonted with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 9 | M&L Granite (of any type and colour) work (table rubbed and polished) 18 to 20mm thick in cooking platforms / WHB and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and directed. |
| 10 | M & L for machine cut kota stone slab flooring in landings of staircase & treads of steps etc. of 20 - 25mm thick (the stone may be in one piece) including rubbing and polishing and to engraved to horzontal lines each step anti skid complete set over and including screed bed or bedding layer of mortar 20 mm thick for laying floor finishes with CM 1:6 complete all as specified and directed. |
| 11 | M & L for machine cut kota stone slab 12 - 15mm thick on vertcle sufaces steps, skirting , and dado of over 10 mm thick plaster in cement mortar in 1:4 jonted with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 12 | Rounding to edges of stone slabs such as steps cooking platform and other similar situations complete all as specified. |
| 13 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each |
| 14 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) Exc 1.5 Sq m but n.exc 4.00 Sq m each |
| 15 | Taking down shutter from the frame) and refixing in same position Exc 1. Sq m but n.exc 2.00 Sq m each |
| 16 | S&F of Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 17 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of sliding windows & ventilators including providing and fixing hinges/ pivots/roller and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (All fittings i.e rollers,locking,Al ventilator louvers arrangement with nobe incl in rates ) with extruded built up standard tubularsections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 18 | S&F 4.00mm thick sheet glass,ordinary quality and glazing with rubber beading or with glazing clips exc 0.5 sq. m in each pane including solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, all as specified and directed. |
| 19 | S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips n exc 0.5, all as specified and directed. |
| 20 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 21 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).property of being ermite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/SS dash fasteners of required dia and length all as specified and directed. |
| 22 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)SS screws complete all as specified and directed. |
| 23 | M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type 1.0mm thick (veneered on both side) with decorative choice laminated type 1 (factory laminated), or surface finish, 6mm thick or external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE. |
| 24 | S & F 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats. |
| 25 | Dismantling Boarding any type, any description, fixed in any position with screws. Complete all as specified and directed by Engr-in-charge. |
| 26 | S&F 12mm frostedToughened glass frameless partition approved brand and manufacture and making necessary holes etc for fixing required partion with CP clamps and at bottom , top and sides Cp pipe of dia 1 with holding CP clamps complete all as specified and as directed of engineer in charge |
| 27 | S&F 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century. |
| 28 | S&F for 100 mm butt hingess, medium weight, cold rolled mild steel, and fixed to steel frame complete all as specified and directed. |
| 29 | S& fixing 75 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed. |
| 30 | S & F 150 mm Aluminium handles, febricated type anodised or fixing to door/cupboard/kitchen cabinet etc,complete all as specified and as directed. |
| 31 | S & F 100 mm Aluminium handles, febricated type anodised or fixing wardrobe cupboard/kitchen cabinet etc,complete all as specified and as directed. |
| 32 | S&F magnetic catch size (70x20x15)mm including fixed with screw complete all as specified |
| 33 | S & F 150 mm long aluminium anodised barrel tower bolt fixed to wiremesh door and equivalent all as specified. |
| 34 | S&F of 300 mm long aluminium anodised sliding door bolt with hasp and staple and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed. |
| 35 | S & F aluminium anodised Hasp and staple, safety type of size 75 mm with mild steel hinge pin including bolt to hinge plate and fixed with screws |
| 36 | S&F floor door stopper of stainless steel and tongue, overall length of cover plate 140mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed. |
| 37 | S& F 40 mm wide Continuous (piano) hinges, brassl, bright finish or electrogalvanised and fixed complete all as specified and directed. |
| 38 | S&F 25mm dia stainless steel tubular curtain rod and fency type socket fixing with brackets, stop, roller etcincl taking down old complete all as specified and directed.Note: design of socket shall be approved by GE/AGE at the time of execution) |
| 39 | S & F in repair towel rail 600 mm CP . Make - Jaqaur code No:AKP-35711P or equivalent make specified in list of make |
| 40 | S&F CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed. |
| 41 | S&F glass shelf with chromium plated guard complete all as specified and directed. |
| 42 | S&F for mild steel Framed work as in doors, windows or gates or grill/grating of angle or other section with gusset plates, rails, braces, etc., complete, drolled for fixing of steel sheeting or other covering. Doors/Windows, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging: also fastening and fixing complete. |
| 43 | M & L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide prime complete all as specified r. |
| 44 | M & L for preparing new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.complete all as specified . |
| 45 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal out side MOD land all as directed by Engr-in-Charge. |
| 46 | S & F 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed |
| 47 | M&L cutting chases brick wall , pinning ,in making good to facing where required in C M 1:3 and pointing or edes of landings, steps , cill sunshed shelves linte cutting chases for concealed water tubingls etc and making good cutting exeeding 20 cm girth |
| 48 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal out side MOD land all as directed by Engr-in-Charge. |
| 49 | S & F 25 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed |
| 50 | Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. |
| 51 | Dismantling of 75mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. |
| 52 | S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed. |
| 53 | S & F 110mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 54 | S & F in 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed. |
| 55 | S & F 75mm PVC (SWR) floor trap, plain with CP grating including jointing with solvent all as specified and as directed. |
| 56 | S & F in 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed |
| 57 | S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed |
| 58 | S & F 110mm PVC (SWR) vent cowl all as specified and as directed |
| 59 | S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed. |
| 60 | S & F 110mm PVC (SWR) junction single, (Single T type) equal or unequal all as specified and as directed. |
| 61 | S& F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed. |
| 62 | S&F grating 150mmx150mm made out of stainless steel complete all as specified and directed. |
| 63 | S & F in repairs under counter basin oval type ivory coloured size(550X400)mm including CP waste coupling ,PVC waste pipe 32 mm dia bore and fixed in 18 mm thick polished granite all as specified and as directed. Note: ( Granite top shall be measured and paid for separately). |
| 64 | S&F in repairs EWC wall hang size 670X390X760 mmwash down water closet pedestal pattern cistern casecade of with twin flushing fitings of ivory coloured including solid seat cover all as specified and directed .Make: Cera Cat No,2035 ,2115,2325&2235 or equivalent as specified make in list of make. |
| 65 | S &F in repairs fancy type Single lever Basin mixer witht with popup waste system & 450 mm long braided houses complete all as specified and as directed .Make:Jaquar code -FLR 5051 B |
| 66 | S &F in repairs fancy type Single lever Wall Mixer with Connector for Hand Shower arrangement with ConnectingLegs, Wall Flanges & Wall Bracket forHand Shower witht with popup waste system & 450 mm long braided houses complete all as specified and as directed .Make:Jaquar code -FLR-5267N |
| 67 | S&F Overhead Shower ø105mm Round Shape Single Flow with Air Effect (ABSBody & Face Plate Chrome Plated) with Rubit Cleaning System (Make : Jaquar code OHS-1709) |
| 68 | S & F Hand Shower ø105mm Round Shape Multi Flow with Air Effect (ABS Body &Face Plate Chrome Plated) with Rubit Cleaning System (Make : Jaquar code HSH-1721 ) |
| 69 | S&F Hand Shower (health faucet) (ABS Body) with 8mm dia 1.0 Meter long Flexible tube& wall hook (Make : Jaquar code ALD CHR-593N) |
| 70 | S & F in repair angular stop cock with wall flange cast cpper alloy fancy type 15 mm .Make: Jaquar , Code No. FLR-5053 N |
| 71 | S & F in repair 2 Way Bib Cock With Wall Flange cast copper alloy fancy type 15 mm .( Make ; Jaquar Code No FLR-5041N. ) |
| 72 | S & F in repair Bib cock (straight line Model) with wall fange cast copper alloy fancy type 15 mm .( Make ; Jaquar Code No FLR-5047 N. ) |
| 73 | S & F in repair 600 mm long braided house MX10X1 Nipple 15 mm nut, O-ring& rubber washer compete all asspecified.Make: Jaquar Code ALD-801AB |
| 74 | S & F in repair stainless steel chromium plated toilet paper holder all as specified and directed. Make - Jaqaur code No:. AKP-35751P |
| 75 | S&F 350x450mm size cabinet mirror rectangular shape with 4mm thick selected quality mirror and PTMT frame with openable door shutter with PTMT frame outside mirror as complete.Make : Prayag & equivalent. |
| 76 | Dismantling of water storage tank of 500 ltrs capacity. |
| 77 | S&F 500 ltrs rotational moulded polythene White colour water storage water tanks twin layered construction ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I duly ISI Marked, complete all as specified. |
| 78 | S & F in repairBall brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 79 | Demolition brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc, |
| 80 | M&L Brickwork fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified |
| 81 | Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc. |
| 82 | M & L Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement) complete all as specified and directed. |
| 83 | M&L rendering 15mm thick on fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth by adding water proofing compound @ 3% by weight of cement without using extra cement, complete all as specified and directed.(Note: WPC item paid seperatly ) |
| 84 | M&L Rendering 5 mm thick on fair faces of brick work or concrete sur-faces of ceiling in cement mortar 1:3 for finished even and smooth (without using extra cement) complete all as specified and directed. |
| 85 | M & L for complete removal of existing treatement of walls by dust proof wall sanding machine/building walls grinding cleaning machine complete all as specified. |
| 86 | M & L for complete removal of existing treatement of ceiling by dust proof sanding machine/buildingrinding cleaning machinecomplete all as specified |
| 87 | M&L for Preparing new plaster surface applying a layer of 1 mm wall care puty on wall and two coat of distemper oil emulsion on internal walls over a coat of primer complete all as specified. |
| 88 | M&L for Preparing new plaster surface of wall applying three coat of white wash on wall complete all as specified. |
| 89 | M & L prepration of surface on wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified. |
| 90 | M&L for Preparing new plaster surface apply three coat of white wash on ceiling complete all as specified. |
| 91 | Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for roof complete all as specified and directed. |
| 92 | M&L for 40 mm avg thick PCC padding in cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggr mixed with WPC @ 2% by wt of cement finished surface even and smooth without using extra cement for laying of WPT all as specified and directed. (WPC will be measured and paid separately). |
| 93 | M&L 10mm thick rendering on roof in CM 1:3 mixed with WPC as per manufacturer's instructions of cement for finished even and smooth without using extra cement over PCC surface for laying APP membrane on roof (WPC will be measured and paid separately). |
| 94 | M&L for water Proofing treatment to roof slabs by applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum 75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed by torch application and applying one coat of aluminium paint @ 0.11 Kg/Sqm over APP membrane complete all as specified and directed by Engr-In-Charge (Note: the primer and the membrane to be used shall be of the same manufacturer and to be applied by authorized applicator of OEM). |
| 95 | Demolition of cement concrete (unreinforced) in ground floor and pavings exc.15 cm thickness (above ground level) and removing from site all as specified and directed. |
| 96 | M&L for 15 mm thick plaster in sunken portion with CM 1:3 mixed with liquid water proofing compound as per manufacturers instruction and should be even and smooth without using extra cement complete all as specified and directed.. Note . (WPC will be measured and paid separately). |
| 97 | M&L for providing & laying applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum 75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed as per manufacturer instructions complete all as specified and as directed. |
| 98 | M&L for sunken portion filled with lean concrete 1:5:10 using brick/lime aggregate and finish the surfaces rough to receive sub base complete all as specified and as directed. |
| 99 | M & L for 25 mm thick cement concrete in flooring type B0, 1:2:4 (12.5mm graded aggregate) with liquid water proofing compound as per manufacturers instructions for laying floor tiles. Note (WPC will be measured and paid separately). |
| 100 | Supply only water proofing compound (Liquid type) all as specified and directed. |
| 101 | M & L for 75 mm thick PCC 1:3:6 mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement. |
| 102 | Demolition of reinforced cement concrete of any description and any pisition not otherwise specifically provided for , all as specified and directed. |
| 103 | M&L for Providing reinforced cement concrete (nominal mix) Type B1, 1:2::4 (using 20 mm graded stone Aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary form work complete all as specified and directed. Note. (reinforcement shall be measured and paid separately) |
| 104 | Use & waste of Formwork flat to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. → |
| 105 | Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for roof complete all as specified and directed. |
| 106 | M&L Cement concrete type B0 1:2:4 (12.50 mm graded aggregate) as in Coping, rounded or chamfered on edgescomplete all as specified and as directed. |
| 107 | Dismantling timber scantlingsfillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section |
| 108 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed |
| 109 | Providing and fixing stainless steel (grade 304) railing made of hallow tubes chennel plates eetc including welding grinding , buffing , polishing and making curvature (wherever required and fittings the same necessary stailess steel dash fasteners stailess steel bolts etc of required the same neccessry stainless steel nuts and bolts etc require size on the top of the floor or the side waist slab with suiltable arrangement as approval by Engr -in charge for payment purpuse of weight of stainless steel member shall be considered excluding fixing accessories such as nuts bolts , fasteners tc ) complete all as specified and as directed by Engr-in charge |
| 110 | Chipping off existing loose, damaged Concrete from RCC members of all affected RCC Columns, Beams, Slabs and Chajjas on External and internal facades, etc beyond main r/f. (if required in the opinion of the Consultant), carefully with chised with chisel and hammer Providing and applying. 'Ruticide SS' Rust passivator or equivalent as specified in the Brand Names to existing r/f. bars including wire brushing of reinforcement, cleaning washing of concrete etc complete all as direted. Providing and \\" applying two coats of rust prevetor slurry made out of \\"Polyalk Fixoprime\\" or equivalent as specified in the Brand Names and cement in Prproportiion 1:1:5 to existing r/f. bars as directed complete. Providing and applying bonding coat of slurry made out of \\"polyalk EP\\" or equivalent as specified in the Brand Names and cement in proportioon1:1 to concrete and r/f substrates complete as directed Providing and applying \\"Polyalk EP\\" or equivalent as (specified in the Brand Names. \\"Polymer modified cement mortar in Required proportions (1:5:15) to RCC members including Hand packing. curing and making the surface rough for plastering. |
| 111 | S& F20 mm outer dia bore Brass Tee |
| 112 | S &F 16/20 mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA) |
| 113 | S& F Brass Elbow 20mm outter dia( 3/4x1/2) |
| 114 | Excavation in trenches in soft/loose of soil, n exc 1.5 M wide and n exc 1.5 M deep for foundation, etc or for shafts, wells, manholes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft and lose soil, complete all as specified and as directed. |
| 115 | Returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete. |
| 116 | Removing excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc. 1.5mtr above the starting point complete. |
| 117 | M&L Plain Cement concrete Type D-2, 1:4:8 (40mm graded aggregate), in foundation, filling and mass concrete, complete all as specified and as directed. |
| 118 | M&L Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:4 |
| 119 | M&L rendering 15mm thick on fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth without using extra cement. |
| 120 | M&L Preparing plastered new surfaces wall Priming plastered and other surfaces paint with two coat cement paint completea all as specified and directed. |
| 121 | S&F aluminium alloy anodized sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing botls and sliding bolts 250mm long. |
| 122 | M&L for Hardcore of broken stone gauge exc 63 mm but n. exc 100 mm deposited spread and levelled in layers n exc 15 cm thick, watered and rolled/ rammed to a true surface |
| 123 | M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) as in floors and finishing the surface rough without using extra cement. |
| 124 | M&L non skid ceramic tiles(Coloured) rectitied 7 to 8mm thick (square/rectangular) area of each tile exc 0.06sqm but n.exc 0.11 sqm, in in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 125 | S & F in 110mm bore PVC (SWR) pipes single socketed,in any length with rubber ring joints,laid in trenches all as specified and as directed. |
| 126 | S & F 75mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 127 | S & F 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed. |
| 128 | S & F 15mm bore chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule |
| 129 | S & F stop valves/Angle valve15mm bore fancy type chromium plated screwed both ends for iron pipe or for unions and fixed |
| 130 | S & F 25mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed |
| 131 | S&F 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/cm2 as in waste pipe |
| 132 | S & FBall brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule and fixed |
| 133 | S&F PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band (flush pipe) 32mm complete all as specified. |
| 134 | S & F 20mm dia stainless steel 600mm long chromium plated tubular towel rail complete all as specified.. |
| 135 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 136 | S & F 110mm PVC (SWR) WC connector bent type to fit WC outlet all as specified and as directed. |
| 137 | S&F vitreous china Wash hand basin, white , size 550x400 mm oval type below counter basin except taps, CP waste coupling but incl brackets all as specified. Make cera/Hindware |
| 138 | S&F Vitreous China, semi-pedestal pattern (Anglo-Indian Type), white (excluding fixing bolts, flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor. complete all as specified and as directed. |
| 139 | S&F Plastic water closet seat,matched with seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 140 | S&F Vitreous China urinals, half stall, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushingcistern, trap and waste pipe) Complete all as specified and directed. |
| 141 | M&L Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete as specified and directed. |
| 142 | S&F towel rail 600mm Long with Lower Hangers, Stainless Steel complete all as specified and directed. (Make: Jaquar or equivalent) |
| 143 | S&F 15mm Pillar taps fancy type, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed as directed by engr-in-chrg. |
| 144 | S & F 32 mm dia stainless steel waste coupling for wash hand basin all as specified and directed. Make : Prayag or equivalant. |
| 145 | S & F PVC connections 15mm size with PTMT nuts of length 450mm |
| 146 | S & F PVC connections 15mm size with PTMT nuts of length 600mm |
| 147 | S&F gratings circular 100 mm size of stainless steel (min wt 50 gms) |
| 148 | M&L for Concrete bed to drain pipes 200 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete. |
| 149 | M&L for UPVC (SWR) 200mm dia pipes for sewage line in existing of Stone glazed stone ware pipe/AC or Reinforced concrete complete all as specified and directed. |
| 150 | M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed |
| 151 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified. |
| 152 | S&F mild steel Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-290 (Gde E 165) |
| 153 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft loose soil |
| 154 | M&L for 75mm thick plain cement concrete type D-2, 1:4:8 using 40mm graded stone aggregate as in sub base of floor complete all as specified directed. |
| 155 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified directed. |
| 156 | M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. |
| 157 | M&L anodised aluminium sections snap grid, wall angle of size 25x25x0.35mm, Main and cross T-section of size 24x38x0.70mm,for grid size 605x605mm false ceiling and adjusting level fixed to roof slabs by means of ceiling cleats made out of complete etc |
| 158 | M&L Fibre insulation boards, ordinary type of 12mm thickness fixed in ceiling complete as directed |
| 159 | M&L for Providing reinforced cement concrete (nominal mix) Type B1, 1:2::4 (using 20 mm Aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed and the like including necessary form work complete all as specified and directed. Note. (reinforcement shall be measured and paid separately) |
| 160 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specifed and as directed. |
| 161 | All as per item No 160 herein before but 5mm dia and over uptoand including 10mm dia in stirrups, spacers and binders |
| 162 | Taking down copper/aluminium point wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fitting , wooden boards, bell push, call bell, MCBs & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall floor etc. |
| 163 | Taking down main switch, DB/change over/VTPN, MCCB AC box of any capacity. |
| 164 | M&L for taking down carefully sub main wiring including batten any type of conduit by unscrewing from floor,wall,ceiling and making good surfaces to match with original status for all types of sub main wiring. |
| 165 | M & L for concealed point wiring complete with multistranded copper conductor (FRLS)1.5 Sqmm size PVC insulated unsheathed cable 1100 volt grade, conforming IS 694 & color code in conduit system of wiring, drawn in including PVC conduit not less than 20 mm dia concealed duly fixed with U-Clips, including cutting chases, finising of slote by means of cement mortor making good to the existing surface of the wall & touching with the existing colour of wall with three coats and making good disturbed surface complete, sunk in pressed Modular Metal flush box of required size not less than 2 mm thick GI Plate factory made with modular cover plate, screw with all accessories including single core multistranded copper conductor 1.5 sqmm size solid PVC insulated unsheathed cable (FRLS) as earth wire to common earth and connected to earth dolly drawn in same conduit for the followings complete all as specified. |
| 166 | For one light, fan point controlled by one switch. |
| 167 | For call bell point controlled by one switch. |
| 168 | For one 5 Amp independent socket point controlled by one switch. |
| 169 | For one 3 pin ,5 Amp socket point with other switch on the same board. |
| 170 | For one light, point controlled by two way switch. |
| 171 | All as per item No 165 here in before but for power point wiring using with 2.5 sqmm PVC-FR LS insulated ,sheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by engir in charge. |
| 172 | All as per item No 165 here in before but for power point wiring using with 4 sqmm PVC-FR LS insulated ,sheathed, copper conductor stranded 1100 volt grade cable and 4 sqmm PVC insulated ,sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by engir in charge. |
| 173 | S&F Modular switch 1 way 6A, 1module. |
| 174 | S&F Modular switch 2 way 6A, 1module. |
| 175 | S&F Modular call bell switch 1 way 6A, 1module. |
| 176 | S&F Modular Socket, 6A - 2/3 pin combined 2module. |
| 177 | S&F Modular switch 1 way 16A, 1module. |
| 178 | S&F Modular Socket, 16A - 3/5 pin combined 2module. |
| 179 | S&F Modular Fan step regulator, 120W - 2 module. |
| 180 | S & F ceiling rose surface polycarbonate body three terminal. |
| 181 | S & F Lamp holder, PVC type with back plate suitable for batten fittings including LED lamp 9 Watt complete all as specified and directed. |
| 182 | M&L concealed Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 6.0 Sqmm size drawn through and including not less than 20 mm dia PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends fixed to the surface of wall/ceiling including one run of 6.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor.NOTE : Two runs of single core 6.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length. |
| 183 | S & F of ceiling fan operated with blades, anti suicide rod from existing roof / trus to fall ceiling, electronic regulator operated and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV ceiling fan complete all as specified and directed.Note : 1) Old ceiling fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 184 | S & F of LED light fitting 20 Watts (4 Feet), 220 Volts AC, Aluminium extrusion , input 140-270 Volts AC, CCT 6000K, luminus efficiancy 100 lumens/watt, surge protection upto 4KV volage protection upto 440V, AC, PF >0.9 and including LED light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 185 | S & F of LED light fitting 10 Watts (2 Feet), 220 Volts AC Aluminium extrusion , input 140-270 Volts AC, CCT 6000K, luminus efficiancy 100 lumens/watt, surge protection upto 4KV volage protection upto 440V, AC, PF >0.9 and including LED light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 186 | S&F sheet metal enclosure for DB double door TPN 04 Ways, IP-43 240 V with 200 Amps rated bus bar Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 187 | S&F sheet metal enclosure for DB double door SPN 12 Ways, IP-43 240 V with 200 Amps rated bus bar Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 188 | S&F testing and commissioning of MCB TPN 240 volt 63 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs including taking down. |
| 189 | S&F testing and commissioning of MCB SPN 240 volt 16 Amp to 40 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs including taking down. |
| 190 | S&F testing and commissioning of MCB SP 6 Amp to 40 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs. All as specified and directed by Engr in charge. |
| 191 | S & F in replacement Bell ding dong type, one way, 240 volts, AC, ISI marked. |
| 192 | S & F of LED bldg security light fitting 35 Watt input voltage 140-270V AC outdoor type with high robust die cast body aluminium housing CCT 6500K lumeinous efficincy > 120 lumens/watts CRI > 70, PF >0.95 protection class IEC safety class-I and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including bracket made out of GI pipe light grade 32mm bore not less than 1.20m long bent to shape required fixed to pole with suitable size 2 Nos clamps made out of 25X3mm flat iron with nut, bolts and washers complete including old U/S taking down complete all as specified and directed. Mak : Havells/Philips/Bajaj .Note :- The warranty on light should be of minnimum 3 Years . |
| 193 | S & F of exhaust fan made of sturdy engineering plastic body complete with louvers shutter & mosquito net, voltage 230V, 50Hz, RPM 1200, copper winding of sweep 250 mm including exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including make hole in stone/brick wall grouting & making good in all aspects and taking down existing UNSV exhaust fan complete all as specified and directed.Note : 1) Old exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 194 | Taking down existing geyser of any capacity, kept in safe condition and refixing after repair, make serviceable with completion of new wiring at same location as per direction of Engr-in-Charge. |
| 195 | Taking down existing energy meter, kept in safe condition and refixing after completion of new wiring at same location with PVC Box as per direction of Engr-in-Charge. |
| 196 | M & L for fabrication of sheet metal board of size 60x50x20 CM made of 2mm thick MS Sheet with locking arrangement dully two coat of synthetic enamelled paint over one coat of red oxide. All as specified and directed by Engr in charge. Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 197 | M&L for Earthing complete with galvanised steel earth plate electrode, 600x600x6mm buried directly in ground (Earth pit not less than 2.25M deep below the GL) with top edge not less than 1.5 metres below ground level connected with galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel all as shown in electric plate no 3 connected to earthing test point all as specified or indicated including testing on completion and including old U/S taking down.Note :- (i) The rate quoted shall also deemed to include the cost of GI wire and protection pipe upto 7.5 Mtr beyond the earth plates electrode and also the cost of the Test point. (ii) Joining of GI earth wire with pipe of the test point shall be done by using suitable cable lugs. |
| 198 | S&F sheet metal enclosure for DB double door SPN 4 Ways, IP-43 240 V with 200 Amps rated bus bar including taking down.Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 199 | S&F sheet metal enclosure for DB double door SPN 8 Ways, IP-43 240 V with 200 Amps rated bus bar including taking down.Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 200 | Taking up GI pipe steel tubing from trench/walls etc including all fittings for following bore of pipe |
| 201 | 50 mm bore |
| 202 | 25 mm bore |
| 203 | S & F to wall/trenches GI steel tubing medium grade including all fittings such as Tees,elbow,bends etc for following bore of pipe complete all as specified. |
| 204 | 50 mm bore |
| 205 | 25 mm bore |
| 206 | S & F in repair Gun metal gate valve iron wheel head screwed both ends for GI steel tubing suitable for 50mm bore of pipe Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 01, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Sep 08, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 6 daysSep 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysSep 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender