Tender For Thorough Repair And Renovation Works To Make Ready As Model Flat For Durgapur And Asansol Zone Named As Zone-B (1 No. Mig-U Type Flat At Shilpa Kanan H.P, Durgapur & 1 No. Lig Type Flat At Kanyapur H.P, Asansol) For The Year 2026-27
Tender Value
4.17 Lakhs
Estimated cost
Bid Submission
21 Aug 2026
4 days left
EMD
8358
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Paschim Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Thorough Repair And Renovation Works To Make Ready As Model Flat For Durgapur And Asansol Zone Named As Zone-B (1 No. Mig-U Type Flat At Shilpa Kanan H.P, Durgapur & 1 No. Lig Type Flat At Kanyapur H.P, Asansol) For The Year 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Taking out carefully Ranigunge pattern tiles from roof stacking seviceable tiles at site and removing rubbish as directed within a lead of 75m. |
| 2 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 3 | Post-Constructional Anti-termite measures:c) Anti-termite treatment to the soil under floor with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water byweight including drilling vertically 12mm.dia holes at the junction of floor and wall at 300mm. interval to reach the soil below using hand operated pressure pump to squirt chemical emulsion into the pump to squirt chemical emulsion into the holes at the rate of one litre per hole. The holes shall be sealed after operation to match with the existing floor. The entire work is tobecarriedout asper specification laid down in para4.3.1.4 of code I.S.-6313(Part-III)1981 |
| 4 | Post-Constructional Anti-termite measures:(d)Anti-termite treatment to the junction of wood work and masonry walls with chemical emulsion byadmixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying at the points of contact with the adjoining masonry by drilling 6m. dia holes at a down ward angle of about 45 degree at the junction of wood work and masonry and squirting chemical emulsion into the seholes at the rate of half litre per hole.The entire work is to be carried out as per specification of Code I.S.-6313 (Part-III)-1981. The shutters are to be sprayed with emulsion. on both sides. All wooden fixtures like almirahs, racks etc. are also to be throughly sprayed with chemical emulsion. (Payment will be made on the basis of outsidemeasurements of doors and windows) |
| 5 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding /staging where necessary . (A) 15 mm thick Plaster(4:1) sand cement motor.(i) INTERNALd) 1st. Floor |
| 6 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.a) Pakur Variety |
| 7 | Washing and cleaning with soap water and rubbing with oil cloth in all types of floor and dado. |
| 8 | (a)Cleaning the walls and ceiling by scraping, sand papering and smoothening down the surface including putting |
| 9 | Supplying, fitting & fixing1st qualityCeramic tiles in walls and floors to match with the existing work & 4nos. of keystones (10mm) fixed with araldite at the back of each tile &finishing the jointswithwhite cement mixed with colouringoxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.A) FloorWithSandCementMortar (1:4) 20mmthick&2mmthickcement slurry at back side of tiles using [email protected]/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative |
| 10 | B) Wall WithSandCementMortar (1:3) 15mm thick & 2mm thick cement slurry at back side of tiles using [email protected]/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative |
| 11 | Post-Constructional Anti-termite measures:(e)Spot application for insecticides using Aquabase spray for pest (for bugs, cockroaches, silverfish, spider, termites,mosquitoes) to walls and ceiling etc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified [email protected] litresper sq.m. by a hand operated pressure pump onwall surfaces, ceiling, electrical fixture,electrical lines including drilling holes in placeswhere sourceof termite is detected squirting chemical solution into the hole and sealing the holes with cement grout. (Rate is per sq.m. of the floor area while actual work will be all walls ceiling, rack, partition and furniture). |
| 12 | (b)Applying 2 coats of Non Toxic Acrylic Polymer modified Paint having adhesive & water proofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required) |
| 13 | Rendering theSurfaceofwalls andceilingwithWhiteCement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 14 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding /staging where necessary . (i) With 1:6 cement mortar (b) 20 mm thick plaster |
| 15 | Grinding to marble / mosaic floor including remaining stone, if necessary, after cutting with manual labour / machine, where necessary |
| 16 | Doors & Windows(A)Supplying fittingand fixingdoor framewithM.S. angle as per drawing & direction of required section.The holes for counter sunk machine screw & nuts will be such as to fit 8 to10 mm Iron screw.The counter sunk nut to be welded. Then utsare to be welded after careful checking with screw. All welding spots should be properly filed or rounded smooth including cost of welding hinges forhingecleats , lugs forhaspbolt, socketbolt etc. and necessary M.S. clampsof 25mm x 6mm flat 225 mm long as per direction welded to the frame fittedandfixed in position excluding cost of concrete. |
| 17 | Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sand wich core,so as to impart monolitaheic composite structure as per approved technology ofDepartment of Science andTechnology (DST) tosafisfy IS: 4020 door testing performance criteria..(i) 66mm x 90mm |
| 18 | Supplying, fitting& fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a specials and wich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science andTechnology (DST) to satisfy IS:4020 door testing performance criteria.In ground floor |
| 19 | Supplying, fittingand fixing M.S. clamps for door and window frame made of flat bentbar, end bifurcated with necessary screws etc.by cement concrete (1:2:4) asper direction. (Cost of concrete will be paid separately) |
| 20 | Anodised aluminiumbarrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fittedand fixedwith cadmium plated screws:vi) 200mm long x 10mm dia. bolt.t. |
| 21 | Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fittedand fixedwith cadmium plated screws:(iv) 75 x 63 x 3.2mm. |
| 22 | Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fittedand fixedwith cadmium plated screws:(vi) 125 x 63 x 3.2mm. |
| 23 | Item No-93 ) Applying Interior grade Acrylic Primer of approved quality and plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (i)Water based interior grade Acrylic primera) One coat. a) In Ground floor |
| 24 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 25 | Supplying fitting and fixing I.R.C. fabric mesh with covering battens includingcost of screws etc complete (excluding the cost of battens).In ground floor.(j) 25mm x 25mm x 2.2mm x 2.2mm. |
| 26 | (a) Metallic magic eye of approved quality fitted and fixed complete |
| 27 | ii) Door stopper (Anodised aluminium) |
| 28 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete(a) With continuous plate base (Hexagonal/ Round rod)(i) 150 mm grip x 12 mm dia rod. |
| 29 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 30 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand pap ering etc. including using of approved putty etc. on the surface, if necessary (a) On timber or plastered surface :(iii) One coats (with any shade except white) |
| 31 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand pap ering etc. including using of approved putty etc. on the surface, if necessary (b) On steel or other metal surface (iii) One coat (with any shade except white) |
| 32 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.ii) 4 mm thick |
| 33 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand pap ering etc. including using of approved putty etc. on the surface, if necessary (a) On timber or plastered surface :(iv) Two coats (with any shade except white) |
| 34 | Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouringoxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor. With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m. (ii) Other than Coloured decorative including white |
| 35 | Supplying best Indian sheet glass pane sset in putty and fitted and fixed with nails and putty complete. (Inall floors for internal wall & upto6m height for external wall)(i) 3 mm thick (weighing 7.4 kg/Sq.m) |
| 36 | Supplying, fitting and fixing bib cock or stop cock.(ii) Chromium plated Concealed Stop Cock (Equivalent to Code No. 514(A) & Model- Tropical / Sumthing Special of ESSCO or similar brand) |
| 37 | a) (i) CP Pillar Cock- 15 mm. (Equivalent to Code No. 507 & Model Tropical / Sumthing Special of ESSCO or similar brand). |
| 38 | Supplying, fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.(iii) 600 mm long |
| 39 | Supplying,fittingandfixingapprovedbrand32mmdia.P.V.C.wastepipe, with PVC coupling at one end fitted with necessary clamps.(iv) 1050 mm long |
| 40 | Supplying, fitting and fixing 10 litre P.V.C. low- down cistern conforming to I.S. specification with P.V.C. fittings complete, C.I. brackets including two coats of painting to bracket etc. |
| 41 | Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges.(i) 450 mm X 300 mm |
| 42 | Supplying, fitting and fixing towel rail with two brackets(iii) 25 mm dia. and 750 mm long |
| 43 | Supplying, fitting and fixing shower of approved brand and make.(ii) Chromium plated round shower with revolving joint (Equivalent toCode No. 541(N) & Model- Tropical / Sumthing Special of ESSCO orsimilar brand). |
| 44 | Rewashering stop cock /bib cock/ push cock/ pillar cock including glandi) 15mm |
| 45 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 46 | Supplying, fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.ii) 450 mm long |
| 47 | Supplying,fittingandfixingapprovedbrand32mmdia.P.V.C.wastepipe, with PVC coupling at one end fitted with necessary clamps. |
| 48 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete(a) E.W.C.(ii) Plastic (hallow type) white |
| 49 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete(b) Anglo Indian(ii) Plastic (hallow type) white |
| 50 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make withnecessary fixing materials and clamps complete.i) Polythene Flush Pipe |
| 51 | Internal Electrical Installation worksSupplying and fixing 240V, 6-16 A SP MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection as per direction of EIC. |
| 52 | Supplying and fixing 240V,40A,DP MCB Isolator on din rail of existing DBs and necessary connection |
| 53 | Supplying & Fixing 240 V AC/DC superior type Ding-Dong Call Bell (Anchor) on HW board incl. S&F HW board |
| 54 | Supply & Fixing angular batten holder (Anchor) on 75mm dia PVC round block / round bakelite on wall/ceiling |
| 55 | Supply & Fixing Socket type fan regulator (Step type)(Brand approved by EIC) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connectionsetc |
| 56 | Supply & Fixing Modular type RJ45 sitable for CAT6 cable (Brand approved by EIC) on existing PVC board and top cover plate on wall and making necessary connections as required |
| 57 | Supply & Fixing Telephone socket (RJ11) Modular type (Brand approved by EIC) on existing GI Modular board having top cover plate and making necessary connections as required |
| 58 | Supplying and fixing 240V, 32 A MCB of Breaking capacity 10kA & C characteristics on din rail of existing enclosure/DB and necessary connection |
| 59 | Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Brand approved by EIC) with 16A Modular type switch, without plug top on 4 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 60 | Supply & Fixing 240 V, 25 A, Modular type starter (Brand approved by EIC) with 25A Modular switch type DP MCB (C Curve) and 4 Module GI Modular type switch board with 4 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cuwire and earth continuity wire etc |
| 61 | GST @ 18% for all items |
| 62 | CESS @ 1% for all items Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysAug 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender