Tender For Certain B&R Repair Works At Icgs Jetty Vadinar Under Ge (I) Cg Porbandar
Tender Value
10 Lakhs
Estimated cost
Bid Submission
03 Sep 2026
18 days left
EMD
20000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jamnagar → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Certain B&R Repair Works At Icgs Jetty Vadinar Under Ge (I) Cg Porbandar
BOQ
| Sl. No. | Item Description |
| 1 | Schedule 'A' |
| 2 | Material & Labour for racking out old joint sealant with masking tape from existing Dummy/Contraction/Expansion joints of dimension 10 mm wide and 10 mm deep and removing the sealant outside the MD land and fixing 12 mm dia polyethylene rod in position as required including treating the sides and bottom of the joint with primer suitable for sealant and refilled with polyurethane joint sealant compound with masking tape using mechanical means to a minimum depth of 8 mm and minimum movement accommodation factor (MAF)=30% conforming to requirements of BS-5212,BS-4254 and EN 141875-2003 for hydrolysis/ water resistance test and making good surface all as per manufactures instructions.Make:- Fosroc Chemicals, M/s. STP Ltd and M/s. Sika India Pvt Ltd or any make as approved by E-in-C's Branch upto date of receipt of tender. |
| 3 | Demolition Cement Concrete of any description and in any position not otherwise specifically provided for drain cover, manhole cover, beam, slab & etc all as specified and as directed. |
| 4 | Material & Labour for Precast RCC cover slab for drain and manhole cover at type B1 1:2:4 (20mm graded aggregate)& set in 1:6 including all necessary formwork and finishing exposed concrete surface without using extra cement complete all as specified and as directed. |
| 5 | Material & Labour for mild steel CRS TMT bars 10 mm dia and over, cut to length, bent shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed. |
| 6 | Demolition of brick and stone wall built in cement mortor incl all quoins, arches, pillars built in cement mortar complete all as specified. |
| 7 | Material & Labour for Pre-cast cement concrete block masonry type C-1, 1:3:6 (20mm graded stone aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge. |
| 8 | Material & Labour for rendering 15mm thick on stone or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Material & Labour for Preparation of new plastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as per the manufacturer’s instructions, complete all as specified and directed by Engineer-in-charge. |
| 10 | Demolition of Un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 11 | Material & Labour for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, sub base and mass concrete, complete all as specified and as directed. |
| 12 | Material & Labour in repair for 60 mm thick coloured rubber moulded factory made machine pressed cement concrete interlocking paver of M-35 grade conforming to IS 15658-2006 of any colour and design as approved made by block making machine with strong vibratory compaction of approved shape, size, colour and pattern, jointed and pointed in grey cement and pigment, complete all as specified and directed by Engr-in-Charge. |
| 13 | Material & Labour in repair for 80 mm thick coloured rubber moulded factory made machine pressed cement concrete interlocking paver of M-40 grade conforming to IS 15658-2006 of any colour and design as approved made by block making machine with strong vibratory compaction of approved shape, size, colour and pattern, jointed and pointed in grey cement and pigment, complete all as specified and directed by Engr-in-Charge |
| 14 | Material & Labour for Filling of dry Sand as in screed bed for PCC interlocking paver block including spreading levelling and well ramming, complete all as specified and directed by Engineer-in-Charge. |
| 15 | Dismantling mild steel work of any description not otherwise provided for etc complete all as specified and directed by Engr-in-Charge. |
| 16 | Dismantling of Plain or corrugated steel sheet, any gauge and thickness, icluding nainital or similar pattern roof covering etc complete all as specified and as directed. |
| 17 | Supply & Fixing for as in posts and struts in fencing incl cutting tops to shape as directed,drilling holes, notching for wire etc; flat iron fillets including all necessary arrangement and similar works conforming to Fe-290 Gde E-165, complete all as specified and as directed. |
| 18 | Supply & Fixing for Mild steel round bars 10 dia as in line wire for fixing in chain link fencing, conforming to Fe-410-W (Gde.E-250) quality -A or Fe 290 (Gde E-165) complete all as specified and as directed. |
| 19 | Supply & Fixing for irons steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, n. exc 5cm long, diameter of neck 5 to 10mm, complete all as specified and as directed. |
| 20 | Supply & Fixing for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grage St-240, complete all as specified and as directed. |
| 21 | Supply & Fixing Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 22 | Material & Labour for preparation of new steel surfaces of any description over 10cm width or girth apply two coats of synthetic enamel painting over one coat of red oxide primer complete all as specified and as directed. |
| 23 | Supply & Fixing in repair MS galvanised chain link fencing with PVC coating weight not less tha 2.50 kg per square meter and dia of wire not less than 2.4 mm wit 1.5mm thick PVC coating and aperture of mesh 75mm x 75mm size all as specifed and directed. |
| 24 | Material & Labour for Providing precast cement concrete type B1, 1:2:4 (20 mm graded stone aggregate) in columns, posts, boundary pillars, bed plates, etc. (of any section indicated), with plain fair faces, including cham fers, weatherings,throat- ing etc. and complete with joints to match setting in CM 1:6 complete all as specifed and as directed. |
| 25 | Material & Labour for preparation of existing treatment of old surface including brooming down , scrapping down smoke soot,mould, moss and efforescent salts and trading oil and grease spouts and cleaning with water on wall applying one coat of Acrylic emulsion (exterior weather coat) paint of any tint as approved complete all as specified and as directed. |
| 26 | Material & Labour for complete removal of existing textured surfaces & preparation and applying for granules textured homogeneous wall finishing system consisting of a two component system of dry granules (25 Kg per Pack) made of 92% silica particles coated with fade resistant pigment, 100% acrylic polymer bonding agent (5 Kg per pack) with the applied thickness of the coating being between 0.8mm -1.2mm to be applied on curved, smooth level plaster without key, as per manufacture directions, for usages to be applied and approved applicator of the manufacture as per the direction/ supervision of the Engineer-in-charge, all complete. The above textured coating should conform to surface spread of flame class one of BS 476:Part 7:1971 and pull off strength of the coating to meet JISA 6909 on smooth plastered surfaces alongwith complete all as specified.Make:- Bakelite Hylam Limited or equivalent make approved by the GE. |
| 27 | Material & Labour for Preparation of old painted of steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysSep 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender