Tender For Provision Of Toilet Block With Bathroom Near Bldg No T-1 Tank Road Offrs Mess Of 130 Sata Regt And Certain Other Works Under Ge (West) Bareilly
Tender Value
29.17 Lakhs
Estimated cost
Bid Submission
02 Sep 2026
9 days left
EMD
58500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bareilly → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Toilet Block With Bathroom Near Bldg No T-1 Tank Road Offrs Mess Of 130 Sata Regt And Certain Other Works Under Ge (West) Bareilly
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard / dense soil.all as specified and directed. |
| 2 | Excavating in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation etc or wells cess pits manholes n.exc 10 Sqm on plan and getting out in soft & loose soil complete all as specified and directed. |
| 3 | M&L for Cement concrete type D 2 1:4:8 (40 mm graded aggregate) in foundation filling and mass concrete |
| 4 | M&L for Reinforced cement concrete (nominal mix) in type B1 1:2:4 (20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 5 | M&L for Reinforced cement concrete (nominal mix) in type B1 1:2:4 (20 mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 6 | M&L for Reinforced cement concrete (nominal mix) in type B1 1:2:4 (20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 7 | M&L for Reinforced cement concrete (nominal mix) in type B1 1:2:4 (20 mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajjas and the like complete all as specified and directed. |
| 8 | M & L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. |
| 9 | M & L formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular finishes rough surfaces of concrete.etc finished rough surfaces of concrete complete all as specified. |
| 10 | M&L Form work to soffits of suspended slabs flat surface of concrete and chajjas finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and directed. |
| 11 | M & L formwork to sides and soffits of lintels,lintel bend, beams etc finished rough surfaces of concrete complete all as specified. |
| 12 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or TMT bars complete all as specified and directed. |
| 13 | M&L Mild steel TMT bars 6 to 8 mm dia as in stirrups and cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or TMT bars complete all as specified and directed. |
| 14 | M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and rammed including watering all as specified and directed. |
| 15 | M&L broken stone or boulder hard core of gauge n exc63 mm deposited spread and levelled in layers n,exc 15 cm thick watered and rammed to true surface complete all as specified and directed. |
| 16 | M&L for 75 mm thick PCC 1:4:8 type D2 (40mm graded aggregate) as in sub bases, sub flooring finished even and rough.complete all as specified and directed. |
| 17 | M&L for 25 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor finishes, floors etc complete all as specifeid and directed. |
| 18 | M&L Damp proof course 40mm thick of PCC type B0 1:2:4 complete all as specified and directed. |
| 19 | M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in, built in CM (1:6) Complete all as specified and directed. |
| 20 | M & L for Brick work with fly ash bricks old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:4 complete all as specified and directed. |
| 21 | M&L for Brickwork with fly ash bricks, straight or curved on plan exc to any radius, half brick walls, built in CM (1:4) Complete all as specified and directed. |
| 22 | M & L for rendering 12 mm thick of fair faces of brick work or concrete surfaces cement plaster 1:6 finished even and fair without using extra cement. |
| 23 | M & L for rendering 15mm thick in cement mortar 1:4 on otherthan fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement complete all as specifed and directed. |
| 24 | M & L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) newly surface even and smooth without using extra cement and necessary scaffolding all as spd and directed |
| 25 | M&L preparation of newly plastered surfaces and applying two coats of oil bound distemper on walls over a coat of primer incliding wall care putty complete all as specified & directed |
| 26 | M&L for preparation of new plastered surfaces of walls and applying two coat exterior emulsion paint over a coat of primer including wall care putty complete all as specified and directed |
| 27 | M&L for three coats of white washing on ceiling surfaces including preparation of newly plastered untreated surfaces and necessary scaffolding all as spd and directed |
| 28 | M&L for Glazed (plain /coloured) ceramic tiles wall 300mmx600mmx7mm thick on vertical faces of walls over and including M&L for 10mm thick rendeing in CM 1:4 set jointed in neat cement slurry and pointed in coloured cement to match complete all as specified. |
| 29 | M & L for non- skid ceremic coloured tiles 7mm to 8 mm thick (Square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and including M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes all as specified. |
| 30 | M&L 16mm to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, door/ window cills, cooking platforms, wash basin counters and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified. |
| 31 | M & L 75 mm thick PCC 1:3:6 type C2 (40mm graded aggregate) as in plinth protection finished even and smooth without using extra cement. complete all as specified. |
| 32 | S & F Solid Prelam WPC solid Door Frame of size 105mm x 65 mm, density more than 0.95, moulded preleminated fixing at opening with screw of size 100 mm long 5 mm dia pling & fixing in opening as per specification and directed Note : Colour to be deceided by GE |
| 33 | S&F 30 mm thick solid core one WPC Modular door, one side Prelam and other side plain fixed in the frame at site as per specification & drawing. complete all as specified. |
| 34 | S&F for 100mm long stainless steel butt hinges complete all as specified and directed. |
| 35 | S&F of aluminium anodised barrel tower bolts of extruded section and fixed 150mm complete all as specified. |
| 36 | S&F of extruded aluminium handles fabricated type anodised 200 mm long complete all as specified. |
| 37 | S&F of 300mm long aluminium anodised sliding door bolts plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as spd and directed. |
| 38 | S& F for steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified. |
| 39 | S&F Figured glass, pin head type 3mm thick and glazing with aluminium glazing clips in square n.exc 0.5 sqm in each pane. |
| 40 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 110mm bore complete all as specified. |
| 41 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 75mm bore complete all as specified. |
| 42 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls 110mm bore complete all as specified. |
| 43 | S&F PVC (SWR) bends any radius 110mm bore complete all as specified. |
| 44 | S&F PVC (SWR) bends any radius 75mm bore complete all as specified. |
| 45 | S&F PVC (SWR) bends any radius 75mm bore with access doors complete all as specified. |
| 46 | S&F PVC (SWR) Ventcowls of bore 110mm complete all as specified. |
| 47 | M & L for PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet in 75mm. complete all as specified. |
| 48 | S&F for 20 mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed. |
| 49 | S&F for 15 mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed. |
| 50 | S&F 20 mm Ball valves high pressure of PTMT with epoxy coated aluminium rod and high dessity plastic ball screwed for iron pipe and fixed ( minimum weight 455 gms) all as specified and as directed. |
| 51 | S&F of 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified. |
| 52 | S&F of 15 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified. |
| 53 | S&F in fancy type chromium plated brass two way bib cock suitable for 15mm bore pipe complete all as specified and directed. |
| 54 | S&F in water jet for EWC chromium plated with PVC connection complete all as specified and directed. |
| 55 | S&F for fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified and directed. |
| 56 | Supply and fix PVC connection 15mm size with PTMT nuts of length 600mm. complete all as specified. |
| 57 | S&F designed looking mirror area exc 0.54 sqm to 0.75 sqm of selected quality 6mm thick glass, mounted on fixed to wall with CP plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 58 | S & F Vitreous China Urinal, Half stall type, white complete including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with 60 mm long brass screws, pointing around urinal back in cement, including all fittings cistern, brackets, flush pipe, spreader, push tap, waste coupling, grating, etc Complete set incl all fitting & fixtures as specified and directed. |
| 59 | S&F Vitreous China table/counter top wash basin of suitable size including SS bottle trap, and cabinet of PVC shutter fixing on counter with SS waste coupling, cp mixer for hot & cold, waste pipe complete all as specified and as directed. Model : Cat No 91072 Orchid of Hindware , Parryware Cat No C0483, Cera Cat No Chauvin S2020166. |
| 60 | S&F Vitreous china wash down water closet single piece (Cascade pattern) with seamless flushing cistern square design duroplast slim seat cover, slow falling seat cover size 69x37x77CM / 66x35x71 complete, including connection to drain pipe etc complete all as specified and directed. Make:- Kerovit Cat Part No: INSIGNIS KS710, Hindware Cat part No.- 92573, CERA CAMPBELL Cat No S1013109/11 & Asian paints Cat Part No OP-30-TFS. |
| 61 | S&F fancy type brass chromium plated toilet paper holder, complete all as specified and as directed. Model No :- ACN-1153N Jaquar, Hindware model No F 880003, Parryware model No T6514A1 & Asian Paints Cat Part No AC506B. |
| 62 | S&F health faucet 1 mtr SS Braided connection tube with wall hook complete for ETWC incl necessary fitting complete all as specified and directed. Make : Jquare Cat Part No ALD-CHR-577, Cera Cat No :- F803008AB, Asian Paints Cat Part No C-232N & Kerovit Cat No KA580008 |
| 63 | S&F fancy type stainless steel towel rack size 600mm long including a pair of brass bracket complete all as specified and directed.Model No :- ACN -1181N of Jaguar ,Cera Model No F5006101, Hindware : F580008 CP & Asian Paints Cat Part No AC-108. |
| 64 | S & F fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified and directed.Model: model No F-5005301 of CERA, Asian Paints Cat Part No AC107 & Kerovit Cat Part No :- KA920005 |
| 65 | S&F rotational moulded polyethylene water storage tanks 1000 ltrs(cylindlerical vertical with closed top) hoisted and fixed in position all as specified in SSR part I. |
| 66 | S&F fancy type brass chromium plated soap dish of 160mmx160mmx90 mm complete all as specified and directed. |
| 67 | S&F of 100mmx100mm stainless steel grating fixed complete all as specified. |
| 68 | Returning filling in including spreading, levelling watering and well ramming in layers not exc 25cm thick. complete all as specified. |
| 69 | Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point. complete all as specified. |
| 70 | M&L for Providing and laying 60 mm thick factory made chamfered edge glossy finished cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer and filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 71 | M & L Providing cement concrete type B0 1:2:4 using 12.5mm agg in kerbs or mud stops rounded edges completed all as specified and directed |
| 72 | M & L for laying of 150 mm dia reinforced concrete pipe, class NP2 pipe laid in trenched and jointed with collers sealed with cement including PCC bebbing, packing under and completely surrounding the pipes after they are laid and tested complete all as specified and directed. |
| 73 | S&F brass chromium plated wall mixer 3 in 1, 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls incl necessary fitting complete all as specified and as directed.Model : Model of Hindware Cat No F390022, Cera Cat Part No :- F1012403, Kerovit Cat Part No KB511018 & Asian Paints Cat Part No ALWM104. |
| 74 | S & F Brass CP Hand Shower with 15mm dia 1.2 Meter long flexible tube and wall hook screwecd for iron pipe fancy type long body complete all as specified and directed.Model No :- Hindware Model No F160053, Cera Cat Part No :-F7030308AB, Kerovit Cat Part No:- KA520008 & Asian Paints Cat Part No HS-208. |
| 75 | S&F fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed. |
| 76 | M&L for PCC kerb stone providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete incl form work weathering, slightly rounded or chamfered angles and throating all as specifed and directed |
| 77 | M&L for Plain Cement concrete 1:3:6 type C2 (Nominal Mix) using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed |
| 78 | M&L for Plain Cement Concrete 1:2:4 type B1 (Nominal Mix) using 20 mm gaded stone aggregate as in surface channel & drain complete all as specified and directed |
| 79 | M&L for Plain Cement Concrete 1:3:6 type C1 (Nominal Mix) using 20 mm graded stone aggregate as in coping, bed plates, wheel guard & other similar work etc. including weathering, slightly rounded or chamfered angles and throating and necessary form work complete all as specified and directed. |
| 80 | M&L for Extra for forming fair finished drain or channel inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. |
| 81 | Material and labour for point wiring with single core FRLS 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with all conduit accessories, screws (concealed conduit wiring in walls and casing capping on ceiling or roof) including metal box suitable for modular fittings and covered with modular plate and cover of suitable size with new brass screws for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:- |
| 82 | (a) All as per item 82 here in before but for One light / fan/ exhaust fan point controlled by one switch. |
| 83 | (b) All as per item 82 here in before but for One 5 pin 5 Amp switch out let point on independent board. |
| 84 | ( c) All as per item 82here in before but for One 5 pin 5 Amp socket out let point controlled by one switch on same board. |
| 85 | All as per item 82 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded incl 2.5 sq mm FRLS PVC copper conductor single core used as earth continuity conductoe complete all as specified.complete all as specified. |
| 86 | S&F, modular switch one way 6 A, 1 module complete all as specified and directed by the engr-in-charge. |
| 87 | S&F modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed by Engr-in-charge. |
| 88 | S & F Modular switch one way 16 A, 1 Module complete all as specified and directed by the Engr-in-Charge. |
| 89 | S & F Modular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge. |
| 90 | S&F, LED light fitting, high lumens batten type, housed in extruded from powder coated aluminium, 20 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed. |
| 91 | S&F MCB SPN 16 Amp 240 volt complete all as specified and directed by the Engr-in-Charge. |
| 92 | Supply and fix electric water heater, storage type steel body with cooper inner tank and heating element upto 2KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate , NRV, connection piece etc complete all as specified and directed by the engr-in-charge. |
| 93 | Supply and Fixing ceiling rose PVC / Poly carbonate, Isolated body, three terminal AC 230 volts complete all as specified and directed. |
| 94 | S&F LED mirror light fitting of 1 x 10 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed. |
| 95 | S&F LED mirror light fitting of 1 x 20 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed. |
| 96 | Supply & Fixing security light fitting, LED type, 35 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed. |
| 97 | Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200, copper winding of sweep 300mm complete all as speccified and directed. |
| 98 | S&F MCP SPN 40 Amp 240 volt complete all as specified and directed by the engr-in-charge. |
| 99 | S&F MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed by the Engr-in-Charge. |
| 100 | Supply and fix flush sheet metal enclosure SPN DB 8 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete including taking down old unsv all as specified and directed. |
| 101 | M&L for earthing and testing complete with galvanized iron earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 M below normal ground level with top edge plate at adepth not less than 1.5M below normal ground level connected to and including earth lead GI wire 4 mm dia, by means of bolts and nuts,check nuts and washers etc.,made of GI and connected to panel/distribution board and earthing test point and earth dolly all as shown in elect plate No.3 of SSR Part-1 including necessary earth work,excavation PCC chamber cover with handle (PCC 1:2:4) incl 20mm dia GI pipe of medium grade for watering and 15mm dia GI pipe of light grade for protection of earthing lead ,wire mesh, funnel, charcoal dust,common salt,copper lugs etc all as specified and directed . |
| 102 | Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm, 2 core. |
| 103 | M&L for sand cushioning by using fine sand in two layers, first layer of 80mm thick before laying of cable and second layer of 150mm thick after laying of cable (total punned depth of sand shall be 180mm after punning down) complete all as specified and directed.. Note- punned thickness shall be measured |
| 104 | M&L Modular bricks common burnt clay building bricks, sub-class ‘B’ designation-75 for LT UG cable protection complete all as spd and directed. |
| 105 | S&F GI tubes light grade of dia 40 mm with all fitting and fixed complete for protection of LT UG Cables laid to walls or in floors or along with poles etc complete all asspd and directed. |
| 106 | M&L for cutting existing steel tubing 50 mm bore for alterations or addition for inserting tees complete all specfied and directed. |
| 107 | Supply and fix Voltage stabilizer for automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 200 KVA |
| 108 | Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armuored, electric power cables (heavy duty) 1100 Volts grade with stranded Copper conductor of cross sectional area 240 Sq mm area 3.5 Core Complete all as specified and directed. |
| 109 | S&F of On-load Changeover switch with SS Enclosure 400 Amp three phase, 415 Volts, 50 Hz, Four Pole complete all as specified and directed. |
| 110 | S&F of GI pipe 80 mm dia, light grade for cable protection, fixed to pole/ alongwall/ floor/ under road/ across the drain or nallaha etc complete all as specified & directed. |
| 111 | Supply, installing, commissioning and testing of LT feeder pillar Box outdoor type of dimension as per specified by manufacturer (not less than 600 x 900 x 450mm ) CPRI certified factory made cubical type weather and vermin proof fixed on and including ventilation and louvers arrangement PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in foundation of required / suitable size and as directed at site with angle iron frame of size 75x75x6mm, 3 phase 4 wire 415 volts 50 Hz fabricated out of 3.15 mm thick CRCA steel sheet including duly painted powder coated and keeping adequate working space inside of the box (outer width of the box not less than 45cm and gap between bus bar not less than one inch) and double door handle including locking arrangement wih 1 No pad lock of 65mm as directed before manufacturing the panel including one no incomer MCCB of cap 400 amp 36 KA with multiple outgoing provission (Min 4 nos) suitable for up to 300 x 3.5 core and Al Busbar of cap 600 Amp rating and Multifuction meter with 3 phase indicator lamp complete all as sepcified and directed. |
| 112 | M&L in Earthing complete with Galvanised iron earth plate electrode 600mm x 600mm x 6mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected with galvanised earthing strip of size 25mm x 4mm by means of nuts, bots, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 40mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (reinforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not esceeding 50 Mtr etc all as shown on electrical plate No.3 of MES Schedule Part-I complete and testing on completion. |
| 113 | Notes:- Tenderers may note that amount as given in schedule of credit will be deducted from the total amount to worked out the net contract sum at the time of Acceptance of tender. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysSep 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender