Tender For Repair To Roof Sheet False Ceiling Flooring Platering And Plinth Protection At Kalimpong And Sherwani Mil Stn Under Ge 867 Ews
Tender Value
20 Lakhs
Estimated cost
Bid Submission
25 Aug 2026
13 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kalimpong → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Roof Sheet False Ceiling Flooring Platering And Plinth Protection At Kalimpong And Sherwani Mil Stn Under Ge 867 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15cm thickness (below or above ground level), etc. complete all as specified and as directed. |
| 2 | M&L for 50 mm thick PCC (1:2:4) type B2 (using 40mm greaded crushed stone aggregate) as in flooring finishing the surfaces even and smooth using extra cement including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges, etc. complete all as specified and as directed. |
| 3 | Taking down cement plaster on brick or stone masonry surfaces of walls etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 4 | M&L for rendering 10 mm thick in cement mortar (1:6) on fair faces of brickwork or concrete surfaces and finished the surfaces even and smooth without using extra cement etc. complete all as specified and as directed. and as directed. |
| 5 | M&L 15 mm thick rendering (in two coats 10mm+5mm) on fair faces of brick work or concrete surface in cement mortar (1:4) on external walls and finished the surfaces even and fair mixed with integral water proofing compound @ 3% by weight of cement in 2nd coat or in the manner specified by the manufacturer and in the proportions indicated, etc. complete all as specified and as directed.Note:-WPC will be measured and paid separately as supply only. |
| 6 | Supply only integral water proofing compound, etc. complete all as specified and as directed. |
| 7 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof coverings etc. complete all as specified and as directed. |
| 8 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet of 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, etc. complete all as specified and as directed. |
| 9 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 10 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated/Plain steel sheet of 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, etc. except sheeting complete all as specified and as directed. |
| 11 | Dismantling wrought iron or mild steel work of any description, etc. complete all as specified and as directed. |
| 12 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe 410-W (Gde 250 quality A), etc. complete all as specified and as directed. |
| 13 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed. |
| 14 | S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre size of grid 605x605mm, etc. complete all as specified and as directed. |
| 15 | S&F Hangers 2 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, etc. complete all as specified and as directed. |
| 16 | M&L 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/ Aluminium framework with screws, etc. complete all as specified and as directed. |
| 17 | S&F Solid PVC Wall Lining consisting of 3mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame incl matching PVC Strips at joints top and bottom with 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified and as directed. |
| 18 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc. complete all as specified and as directed. |
| 19 | M&L for vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20mm thick screed bed or bedding layer in CM (1:6), etc. complete all as specified and as directed. |
| 20 | M&L for vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, in vertical surface etc. such skirting/ dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM (1:4), etc. complete all as specified and as directed. |
| 21 | M&L Glazed ceramic coloured tiles in vertical surface 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 15 mm thick screed bed or bedding layer in CM (1:4) finished even and rough complete all as specified and directed. |
| 22 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to IS-13712, grade B-II(a) (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and directed. |
| 23 | Taking down chowkhats or frame not exc 1.50 sqm each with shutter (without taking off shutters from the frame), etc. complete all as specified and as directed. |
| 24 | Taking down chowkhats or frame exc 1.50 sqm and n.exc 4.00Sqm each with shutter (without taking off shutters from the frame), etc. complete all as specified and as directed. |
| 25 | Taking down shutters of any description exc 1 sqm and n.exc 2 sqm etc. complete all as specified and as directed. |
| 26 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm with using single side prelam PVC sheet, reinforced with M.S. Square tube, fixing in opening as per specification & drawing, etc. complete all as specified and as directed. |
| 27 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles a PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail with using both side Prelam PVC sheet at Stile and rails feathered at edges beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing, etc. complete all as specified and as directed. |
| 28 | S&F 100 mm size butt hinges of medium weight, stainless steel, etc. complete all as specified and as directed. |
| 29 | S&F 100mm long Aluminium anodised tower bolts of extruded section fixed with screws etc. complete all as specified and as directed. |
| 30 | S&F 125 mm long Aluminium anodised handles extruded section fixed with screws etc. complete all as specified and as directed. |
| 31 | S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, etc. complete all as specified and as directed. |
| 32 | S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, etc. complete all as specified and as directed. |
| 33 | S&F mild steel framed work such as grills, grating etc. with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars,barred iron doors, ladders, framed balusters, walk ways, railings and similar work confirming to Fe-410-0 or Fe 310-0, complete all as specified and as directed. |
| 34 | S&F in repair stainless steel wire cloth 0.36mm nominal dia if wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc. complete all as specified and as directed. |
| 35 | S&F in repairs decorative type drapery curtain rod (curtain rails), of 25 mm dia powder coated with fixing. Including decorative Knobs and fixiing in pairs of brackets, stops etc, complete all as specified and as directed. |
| 36 | M&L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, etc. complete all as specified and as directed. |
| 37 | S&F in repair Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 1000 mm in width and of weight not morethan 35 kg and fixed of aluminium (extruded section body), complete all as specified and as directed. |
| 38 | S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long etc. complete all as specified and as directed. |
| 39 | S&F Corner glass shelf set of 3 of size 185x185mm, 235x235mm & 290x290mm transparent type, etc. complete all as specified and as directed. |
| 40 | M&L for preparation and applying two coats of Oil bound distemper over a coat of chalk whiting priming paint on new wall surfaces etc. complete all as specified and as directed. |
| 41 | M&L for preparation and applying two coats of Cement Base Paint of approved tint over a coat of alkali resistant priming paint on new wall surfaces etc. complete all as specified and as directed. |
| 42 | M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, etc. complete all as specified and as directed. |
| 43 | S&F for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed. |
| 44 | S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc, complete all as specified and as directed. |
| 45 | S&F Anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, roller, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21, 100mm long (2 no.) suitable handle (1no.),handle cum latch lock complete all as specified and as directed. |
| 46 | M&L for 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed. Please Enable Macros to View BoQ information |
| 47 | M&L for 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender