Tender For Fabrication, Installation & Finishing Of Custom Made Fixed And Loose Furniture, Interior Joinery, Allied Fit-Out & Furnishing Works For Civil Services Officers Institute, Hcm Ripa Jaipur
Tender Value
2.30 Crore
Estimated cost
Bid Submission
19 Aug 2026
3 days left
EMD
4.60 Lakhs
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Fabrication, Installation & Finishing Of Custom Made Fixed And Loose Furniture, Interior Joinery, Allied Fit-Out & Furnishing Works For Civil Services Officers Institute, Hcm Ripa Jaipur
BOQ
| Sl. No. | Item Description |
| 1 | OFFICE TABLE WITH SIDE STORAGE UNIT |
| 2 | Providing, fabricating and Placing in position Executive Office Desk (L-Shaped Configuration) having an overall arrangement comprising of one Main Executive Desk of size 1800L × 750D × 750H mm and one Side Storage Unit of size 1800L × 450D × 600H mm, positioned together to form an L-shaped executive workstation. The complete desk shall be manufactured using solid White Ash Wood, White Ash Veneer & HDHMR Board. All external exposed surfaces in Grey Tone shall be made using HDHMR 18MM sheet with Solid PU finish and all natural wood finish surfaces shall be made using Solid White Ash wood and White Ash Veneer. The table top shall be made in White Ash Veneer and will have a 40mm thick appearance achieved by providing suitable built-up edge made using solid White Ash wood lipping below the top. The Main Executive Desk shall be provided with an integrated storage pedestal comprising three drawers of size 400mmLx170mmH fitted with telescopic drawer channels of Hettich, Hafele or equivalent approved make and stainless steel satin finish handles. The Side Storage Unit shall comprise three drawers 400mmLx170mmH , 02 open shelving compartment and 02 nos closed storage cabinet with 01 nos of shelf inside with hinged shutters, all matching the approved design. The desk shall be provided with one Pop-up Box on the main table top and one cable manager on the side unit top for concealed cable routing. A full modesty panel shall be provided below the main desk using HDHMR 18MM sheet with PU finish . All necessary hardware including concealed hinges, telescopic drawer channels, stainless steel handles and accessories shall be provided of approved make. The item cost shall include all materials, labour , transportation, installation, etc complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge. |
| 3 | HIGH BACK CHAIR |
| 4 | Providing and placing in position a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be made of metal insert pipe frame padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ in seat and (19+12)mm thick having density 23kg/m³ in back. The seat and back shall be upholstered with leatherite tapestry 1mm thick and 571 GSM of approved colour and shade. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support as well as head support. The chair shall be supplied with chrome plated arm having black integral polyurethane top. For seating durability the chair shall have knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti-shock feature which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with gas-lift to suit them using the lever under the seat. The Pedestal should have five legged made of MS CRCA chrome plated having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors which shall be made of injection moulded in black 30% glass filled nylon, confirming to industry standards tested to perform 98,000 cycles with 250lbs load. The seat size shall be 480±10 mm(D) X 475±10 mm(W) and back size shall be 465±10 mm(W) X 690±10 mm(H) from seat. Overall height shall be = 1160±10 mm, overall depth = 620±10 mm & overall width = 570±10 mm. The item cost shall include all materials, labour , transportation, installation, etc complete in all respects as per the directions of the Engineer-in-Charge. |
| 5 | VISITOR CHAIR |
| 6 | Providing and placing in position a visitor chair with ergonomic design for user comfort & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be made of metal insert pipe frame padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ in seat and (19+12)mm thick having density 23kg/m³ in back. The seat and back shall be upholstered with leatherite tapestry 1mm thick and 571 GSM of approved colour and shade. The backrest shall be made by keeping the natural curvature of the spine for back support. The chair shall be supplied with MS chrome plated arm having black integral polyurethane top. The frame structure shall be cantilever support type made of MS CRCA chrome plated round pipe dia. 28mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 460±10 mm(D) X 480±10 mm(W) and back size shall be 485±10 mm(W) X 510±10 mm(H) from seat. Overall height shall be = 980±10 mm, overall depth = 600±10 mm & overall width = 570±10 mm. The item cost shall include all materials, labour , transportation, installation, etc complete in all respects as per the directions of the Engineer-in-Charge. |
| 7 | OFFICE WORKSTATION |
| 8 | Providing, manufacturing and fixing in position of Office Workstation having overall size of 1140L × 600D × 2150H mm. The workstation shall be manufactured using a combination of 18 mm HDHMR Board with Solid Coloured PU Finish, Solid White Ash Wood and 18 mm White Ash Veneered Plywood, complete in all respects as per approved drawing.All Grey finished surfaces shall be manufactured from 18 mm HDHMR Board finished with premium PU Paint in approved solid colour, including all exposed edges, to achieve a seamless finish. All natural wood finished surfaces including exposed table top, cabinet shutters, side panels, back panel, modesty panel, shall be manufactured using 18 mm White Ash Veneered Plywood with 10 mm solid white ash wood lipping on all exposed edges, finished in approved stain shade with PU clear finish. No laminate shall be used on any exposed visible surfaces.Each workstation shall comprise one Table with side partition (1140L × 600D × 750–900H mm), one wall mounted overhead cabinet (1140L × 300D × 800H mm), one wall mounted back panel (1140L × 18T × 600H mm) and one pedestal storage cabinet (450L × 450D × 680H mm) placed below the table top, forming one complete workstation unit.The table top shall be 36 mm thick, fabricated using 18 mm White Ash Veneered Plywood with an additional 18 mm build-up below the front edge to achieve the required thickness. The side partition shall be fabricated from 18 mm White Ash Veneered Plywood. The overhead cabinet carcuss shall be fabricated using 18 mm HDHMR Board for all grey finished members and 18 mm White Ash Veneered Plywood for Shutters. Cabinet back shall be 18 mm MR Grade Plywood in matching finish. The cabinet shall be provided with two shutters and one adjustable shelf inside. The wall mounted back panel shall be fabricated using 18 mm White Ash Veneered Plywood, as per approved finish. |
| 9 | All internal cabinet surfaces shall be manufactured using 18 mm MR Grade Plywood finished in matching outer finish. Drawer boxes shall be manufactured using 18 mm MR Grade Plywood, while drawer bottoms shall be 9 mm thick plywood securely housed in grooves. All exposed edges shall be finished with matching Solid White Ash lipping or PU-finished edges, as applicable.The workstation shall be fitted with one cable manager on the table top, 100 mm long Stainless Steel handles, good quality locks for shutters and drawers, 350 mm telescopic drawer channels, 75 mm Stainless Steel butt hinges, magnetic catchers, door latch, buffers and all necessary hardware and accessories of approved make. |
| 10 | MID BACK CHAIR |
| 11 | Providing and supplying Mid back chair. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resiliance polyurethane foam 40mm thick having density 40kg/m³ with fabric tapestry 0.6mm thick and 235 GSM and the back shall be made of two piece injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The armrest of the chair shall be used polypropylene arm completely joint with seat & back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 120mm with Class-3 gas-lift to suit them using the lever under the seat. The pedestal should have five legged injection moulded in black nylon having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black nylon 30% glass filled, tested to perform 98,000 cycles with 250lbs load. The seat size shall be 470±10 mm(W) X 460±10 mm(D) and back size shall be 460±10 mm(H) from seat & overall height = 865±10 mm. |
| 12 | RECEPTION COUNTER |
| 13 | Providing, fabricating and Placing Reception Counter having overall size of 2100L × 750D × 1050H mm with working counter height of 750 mm and visitor counter height of 1050 mm, manufactured in Solid Sheesham Wood duly seasoned and chemically treated and Sheesham Veneered Plywood as per approved design. The reception counter shall be designed in a two-step profile with a raised visitor transaction counter of size 1650L × 300D mm and a full-depth writing counter below. Both counter tops shall be finished with 30 mm thick stone (15 mm stone with 15 mm edge moulding) in approved Italian Marble of Min. Rs.800/sqft as selected by the Engineer In-Charge.The primary structural framework shall be fabricated using Solid Sheesham Wood sections of 60×40 mm and 75×40 mm. The main counter top shall be fabricated using 18 mm MR grade Plywood with 60 mm thick built-up edge framing, while the raised visitor counter shall be fabricated using 18 mm MR grade Plywood with 40 mm thick built-up edge. Vertical side panels, end panels, partitions and front framework shall be made using 18 mm Sheesham Veneered Plywood. The front elevation facing the visitor shall consist of raised moulded panel construction with four equally proportioned recessed panels framed using Solid Sheesham Wood mouldings of approximately 45×18 mm section, fixed over veneered plywood panels to achieve the classical panelled appearance as shown in the approved design. The counter shall incorporate stepped side projections and a stepped front profile complete with Solid Sheesham Wood skirting and mouldings of 75 mm overall height built using moulded sections of approximately 45×25 mm and 25×18 mm.The reception counter shall be provided with 02 Nos. pedestal storage units, one each on the left and right side of the attendant. Each pedestal shall have overall size approximately 450L × 550D × 660H mm and shall consist of 03 drawer. The pedestal carcass shall be fabricated using 18 mm Sheesham Veneered Plywood, while the back shall be 12 mm MR Grade Plywood. Drawer fronts shall be made using 18 mm Sheesham Veneered Plywood with recessed panel detailing matching the counter design. Drawer sides and back shall be fabricated using 18 mm MR Grade Plywood, with 12 mm MR Grade Plywood drawer bottom suitably grooved and fixed. The pedestals shall be fitted with 450 mm heavy-duty telescopic drawer channels, 100 mm Stainless Steel handles, cam locks, nylon buffers and all necessary hardware of approved make. |
| 14 | All exposed mouldings, skirting, framing members, decorative profiles, edge members and structural visible components shall be fabricated in Solid Sheesham Wood, while all large flat exposed surfaces including side panels, front panels, drawer facias, shall be finished using Sheesham Veneered Plywood of suitable thickness. Internal concealed components, cabinet backs and non-visible structural members shall be fabricated using MR Grade Plywood of appropriate thickness.All exposed timber and veneered surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The counter shall be complete with all necessary fixtures and accessories including cable manager, Stainless Steel handles, telescopic channels, locks, buffers, and all incidental hardware required for proper functioning. The item shall include all materials, stone, polishing, hardware, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 15 | RECEPTION CHAIR |
| 16 | Providing and supplying revolving chair with ergonomic design. The seat shall be made of 15mm thick ply-board padded with high resilience polyurethane foam (50+50)mm thick having density 40kg/m³ and the back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 40mm thick having density 32kg/m³. The same shall be upholstered with fabric/leatherite tapestry . The backrest shall be made by keeping the natural curvature of the spine. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for seating, user can adjust seat height up to 100mm with class-3 gas-lift to suit them using the lever under the seat. The pedestal should have five legged MS/CRCA black having pitch circle dia. 640 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, tested to perform 98,000 cycles with 250lbs load. The seat size shall be 470±10 mm(D) X 475±10 mm(W) and back size shall be 525±10 mm(W) X 380±10 mm(H) from seat. Overall height shall be = 805±10 mm, overall width (arm) = 610±10 mm, Base width/depth = 760±10mm. |
| 17 | WAITING AREA SOFA 2 SEATER |
| 18 | Providing, fabricating and Placing in position Waiting Area Sofa 2 Seater having overall size of 1500L × 800D × 870H mm with seating height of 430 mm, effective seating depth of 650 mm, clear seating length of 1200 mm (600 mm per seat), armrest height of 270 mm above seat, fixed backrest cushion height of 420 mm above seat, and arm width of 150 mm, manufactured as per approved design and drawing. The sofa shall be fully upholstered in Premium Upholstery Fabric of approved shade and texture of not less than ₹800/- per metre MRP, including all upholstery work complete in all respects.The sofa shall have an internal structural framework fabricated using Solid Sheesham Wood duly seasoned and chemically treated, comprising primary load-bearing members of 75 × 30 mm and 60 × 30 mm sections with intermediate supports of 40 × 30 mm section, rigidly jointed using mortise and tenon joints and waterproof adhesive. The exposed base legs shall be fabricated in Solid Sheesham Wood, 150 mm wide and 40 mm high, recessed below the upholstered base to provide the floating appearance shown in the approved design. All exposed wooden components shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat.The upholstered seat shall be 155 mm thick overall, consisting of 125 mm thick PU Foam of 32 density fixed over an independent Solid Sheesham Wood seat frame of 60 × 30 mm section. The seat support system shall consist of elastic webbing and zig-zag springs fixed over the timber frame to provide resilience and long-term seating comfort. Upholstery shall be completed with jute hessian cloth, cotton marking cloth, SR adhesive and all necessary upholstery consumables. The complete seat assembly shall be securely fixed to the main sofa structure. |
| 19 | The upholstered base frame below the seat shall be 235 mm high and constructed using Solid Sheesham Wood framework , fully upholstered to match the sofa design. The armrests shall be 150 mm thick, fabricated using MR Grade Plywood supported on solid wood framing and upholstered with 50 mm thick PU Foam of 32 density of approved make to achieve the required profile and comfort. The fixed backrest shall comprise a 70 mm thick upholstered structural panel extending 270 mm above the seat, fabricated using MR Grade Plywood over solid wood supports. The fixed back cushion mounted above the structural back shall project 420 mm above the seat, shall be 150 mm thick overall, and shall be upholstered using75 mm thick PU Foam of 32 density with additional polyester fibre wrapping to achieve the soft cushioned profile shown in the approved design.The sofa shall be complete with all necessary hardware, concealed fixing accessories, nylon buffers, labour, transportation, loading, unloading, installation and all incidental works, finished in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 20 | CENTRE TABLE |
| 21 | Providing, fabricating and Placing Centre Table having overall size of 1200L × 600D × 450H mm with100 mm floor clearance, manufactured using Solid Sheesham Wood duly seasoned and chemically treated and Sheesham Veneered Plywood as per approved design and drawing. The table top shall be fabricated using 18 mm MR Grade Plywood with 15–18 mm thick Italian/Indian Marble of approx Rs.800/sqft of approved quality and shade pasted over the plywood using suitable adhesive, complete with machine-finished edges. The exposed structural framework, legs, top frame and lower support members shall be fabricated from Solid Sheesham Wood. The main top framework shall be made using 50 × 30 mm solid wood sections, while the lower shelf support framework shall be made using 40 × 30 mm solid wood sections. The table shall be supported on Solid Sheesham Wood legs of 65 × 65 mm section tapering uniformly to 45 × 45 mm at the bottom, maintaining the proportions shown in the approved design.The lower storage shelf shall be fabricated using 18 mm Sheesham Veneered Plywood, fixed within the solid wood framework to provide an open storage platform below the table top. All exposed edges of the veneered shelf shall be finished with matching Solid Sheesham Wood lipping.All exposed solid wood and veneered surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The table shall be provided with nylon buffers below the legs for floor protection. The item shall include all labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 22 | CORNER TABLE |
| 23 | Providing, fabricating and Placing Centre Table having overall size of 550L × 550D × 550H mm with100 mm floor clearance, manufactured using Solid Sheesham Wood duly seasoned and chemically treated and Sheesham Veneered Plywood as per approved design and drawing. The table top shall be fabricated using 18 mm MR Grade Plywood with 15–18 mm thick Italian/Indian Marble of approx Rs.800/sqft of approved quality and shade pasted over the plywood using suitable adhesive, complete with machine-finished edges. The exposed structural framework, legs, top frame and lower support members shall be fabricated from Solid Sheesham Wood. The main top framework shall be made using 50 × 30 mm solid wood sections, while the lower shelf support framework shall be made using 40 × 30 mm solid wood sections. The table shall be supported on Solid Sheesham Wood legs of 65 × 65 mm section tapering uniformly to 45 × 45 mm at the bottom, maintaining the proportions shown in the approved design.The lower storage shelf shall be fabricated using 18 mm Sheesham Veneered Plywood, fixed within the solid wood framework to provide an open storage platform below the table top. All exposed edges of the veneered shelf shall be finished with matching Solid Sheesham Wood lipping.All exposed solid wood and veneered surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The table shall be provided with nylon buffers below the legs for floor protection. The item shall include all labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 24 | CONFERENCE TABLE |
| 25 | Providing, fabricating and Placing in position Conference Table having overall size of 5480L × 1800D × 750H mm, manufactured using Solid Sheesham Wood duly seasoned and chemically treated and Sheesham Veneered Plywood as per approved design and drawings. The table shall be designed to comfortably accommodate 16–18 persons with adequate knee and leg clearance on all sides. The table top shall be fabricated using 18 mm thick Sheesham Veneered Plywood with a 50 mm thick edge profile, achieved by providing a 50 × 32 mm solid Sheesham wood framing below the perimeter to create the appearance of a thick top. The top shall be reinforced on the underside with 75 × 40 mm solid Sheesham wood cross members. The table shall be provided with 08 nos. flush-mounted pop-up box of approved make, positioned appropriately, complete with concealed cable routing provision inside the pedestal. Each pop-up box shall be provided with a flip-top aluminium cover and shall be fitted with 02 nos. 6A universal power sockets, 01 USB Type-A charging port, 01 USB Type-C charging port, 01 RJ45 data port and 01 HDMI pass-through port, complete with wiring access opening and cable exit arrangement.The central pedestal base shall be proportioned to provide maximum seating comfort and unobstructed leg space. The overall pedestal size shall be approximately 3900L × 800D × 700H mm, centrally positioned below the table. The pedestal framework shall be constructed using Solid Sheesham Wood sections of 75 x 38 mm and 50 × 38 mm, rigidly joined using mortise and tenon joints, waterproof adhesive. The visible pedestal faces shall be fabricated using 18 mm Sheesham Veneered Plywood finished with classical recessed panel detailing. Each panel shall be enclosed within 60 mm wide solid Sheesham wood stiles and rails, with 18 × 12 mm solid Sheesham mouldings fixed around the recessed panels as shown in the approved design. The pedestal shall be finished with a 100 mm high solid Sheesham wood skirting comprising a 50 × 25 mm base member and decorative moulded profile. Internal structural members shall be adequately braced to provide rigidity and support to the table top.All exposed edges shall be finished with matching Solid Sheesham Wood lipping. All exposed solid wood and veneered surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The table shall be provided complete with pop-up box , concealed fixing hardware, levelling nylon buffers, all necessary fittings, labour, transportation, loading, unloading & installation. The item shall be completed in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 26 | CONFERENCE CHAIR MID BACK (GRACE 2) |
| 27 | Providing and placing in position ergonomically designed, comfortable & aesthetically appealing Mid back chair. The seat shall be made of metal insert MS CRCA chrome plated upholstered with high resilience polyurethane foam 30mm thick having density 60kg/m³ with leatherite tapestry 0.8mm thick and 535 GSM and the back shall be supported by MS CRCA chrome finish upholstered with high resilience polyurethane foam 30mm thick having density 30kg/m³ with leatherite tapestry 0.8mm thick and 535 GSM of approved colour and shade with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. The seat and back shall be fixed with metal frame and the armrest shall be used crome pipe with cusion completely joint with seat and back. The chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 120mm class-3 gas lift to suit them using the lever under the seat. The Pedestal shall be made up of MS CRCA chrome plated having pitch circle Dia 700 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen . The Seat size shall be 510±10 mm(W)X480±10 mm(D) and back size shall be 510±10 mm(W)X480±10 mm(H) from seat & & overall back height = 530±10 mm. overall height = 890±10 mm- 990±10 mm. |
| 28 | CONFERENCE CHAIR (GRACE 3) |
| 29 | Providing and placing in position ergonomically designed, comfortable & aesthetically appealing Visitor chair. The seat shall be made of metal insert MS CRCA chrome plated upholstered with high resilience polyurethane foam 30mm thick having density 60kg/m³ with leatherite tapestry 0.8mm thick and 535 GSM and the back shall be supported by MS CRCA chrome finish upholstered with high resilience polyurethane foam 30mm thick having density 30kg/m³ with leatherite tapestry 0.8mm thick and 535 GSM of approved colour and shade with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. The seat and back shall be fixed with metal frame and the armrest shall be used crome pipe with cusion completely joint with seat and back. The chair shall have Cantilever CRC Frame with Chrome finish . The Seat size shall be 510±10 mm(W)X480±10 mm(D) and back size shall be 510±10 mm(W)X480±10 mm(H) from seat & & overall back height = 530±10 mm. overall height = 890±10 mm- 990±10 mm. |
| 30 | RESTAURANT SERVING COUNTER |
| 31 | Providing, fabricating and placing in position restraunt service counter as per given design the Restaurant Service Counter shall be of overall size 8730 mm (L) × 750 mm (D) × 900 mm (H) and shall be fabricated in two equal units of approximately 4365 mm length each for ease of transportation, handling and installation. Both modules shall be joined on site using concealed heavy-duty connectors to provide a rigid, perfectly aligned and seamless finished appearance.The complete counter shall be manufactured using 18 mm thick seasoned and chemically treated Solid Sheesham Wood for all exposed panels, framing members, partitions, shelves, drawer fronts and structural components. The counter top shall comprise 15 mm thick Italian Marble (approximate material value Rs.800/- per sq.ft.) fixed over 18 mm thick MR Grade Plywood substrate. The marble shall have moulded edges to achieve an overall visible thickness of 30 mm. Marble shade, pattern and finish shall be as approved by the Engineer-in-Charge.The front customer-facing elevation shall be designed as a clean contemporary panelled façade comprising recessed solid wood panels with projecting vertical and horizontal framing members of size 25x40mm, creating a symmetrical grid pattern as shown in the approved design. The front elevation shall serve as a decorative architectural feature with continuous wood grain and uniform proportions.The service side shall be provided with a continuous row of top drawers extending across the counter length. Drawers shall be constructed in Solid Sheesham Wood and fitted with heavy-duty full-extension telescopic channels and 150 mm long metal handles of approved design and finish. Below the drawers, the counter shall be provided with open storage shelving divided into practical storage bays using fixed vertical partitions and intermediate shelves for storing crockery, trays, cutlery, service accessories and restaurant operating supplies.The counter shall be provided with a 100 mm high recessed plinth . All exposed edges shall be neatly finished with rounded profiles, and all joints shall be accurately aligned. |
| 32 | All exposed wooden surfaces shall be machine sanded smooth, stained in Walnut Brown, sealed with two coats of wood sealer, and finished with premium satin melamine polish. The complete item shall include all necessary hardware, concealed fasteners, fittings, polishing, transportation, assembly, installation and finishing, complete in all respects as approved by the Engineer-in-Charge. The work shall be complete as per given design, drawing and direction of Engineer-Incharge. |
| 33 | RESTAURANT CROCKERY/BAR DISPLAY UNIT |
| 34 | Providing, fabricating and placing in position Crockery / Bar Display Unit as per given designOverall Dimensions: 6555 L × 625/450 D × 2400 H mmThe Crockery Unit / Back Bar Display Unit shall be of overall dimensions 6555 mm (L) × 625 mm (Base Depth) / 450 mm (Top Display Depth)/300 mm (Open Shelving Depth) × 2400 mm (H) and shall be fabricated in modular construction using seasoned and chemically treated Solid Sheesham Wood, Sheesham Veneered Plywood, MR Grade Plywood, premium hardware and lighting accessories, complete in all respects as per approved drawings.The complete unit shall comprise a 625 mm deep base storage cabinet and a 450 mm deep upper display section, integrated into a single continuous architectural unit with matching cornice, mouldings and skirting.The structural framework shall be fabricated using 50 × 30 mm Solid Sheesham Wood members with intermediate rails and vertical supports as required to ensure rigidity. All exposed framing, face frames, drawer facias, skirting, cornice mouldings, edge members and decorative trims shall be manufactured from Solid Sheesham Wood. All exposed side panels, cabinet panels, shutter panels, shall be manufactured using 18 mm thick Sheesham Veneered Plywood with 22 mm thick Solid Sheesham wood lipping on exposed edges. All internal vertical partitions and fixed shelving shall be made using 18mm MR Grade Plywood. The base cabinet shall be approximately 900 mm high including countertop and skirting. It shall comprise a continuous row of drawers at the top, each approximately 180 mm high, with framed Solid Sheesham drawer facias. Drawers shall be fitted with heavy-duty full-extension telescopic channels and Antique Brass finish handles of approved design. Below the drawers shall be double-door storage cabinets approx 1000mm wide, each fitted with one adjustable 18 mm thick shelf inside, creating two storage compartments. Doors shall be framed in Solid Sheesham Wood with 12mm Sheesham veneered plywood panels in the centre.The base cabinet shall incorporate a 100 mm high recessed Solid Sheesham skirting . Decorative cornice and moulding members shall be 50–60 mm projection with clean classical profiles matching the approved design. |
| 35 | The usable countertop shall be finished with 15 mm thick Italian Stone of Min. Rs.800/sqft of approved shade , fixed over 18 mm thick MR Grade Plywood, with moulded edge build-up to provide an overall visible thickness of approximately 30 mm.The upper display unit shall consist of two enclosed display cabinets approx 1000 mm wide on either side and a central open display shelving system. The enclosed display cabinets shall be fitted with 8 mm thick clear bevelled glass shutters housed within Solid Sheesham frames. Each cabinet shall be provided with 3 Nos. 8 mm thick clear tempered glass shelves, equally spaced at approximately 320–350 mm vertical centres, suitable for display of crockery and glassware. Cabinet interiors shall be illuminated with concealed Warm White LED lighting.The central open display shelving shall measure approximately 4555 mm overall length, 300 mm shelf depth, and shall comprise four continuous display shelves fabricated from 18 mm thick Sheesham Veneered Plywood with 40 mm thick Solid Sheesham edge profiles. The shelves shall be vertically spaced at approximately 350 mm clear height to accommodate bottles and display items. Each shelf shall incorporate a concealed Warm White LED strip fixed beneath the front edge to uniformly illuminate the shelf below.The open shelves shall be structurally supported at the front using 30 mm diameter decorative MS pipes in Antique Brass finish, fixed continuously from countertop to top canopy at appropriate intervals of approximately 600 mm centres, providing both structural support and architectural detailing. Rear shelf support shall be fixed to the plywood back panel using concealed heavy-duty brackets.The top of the display unit shall be finished with a continuous Solid Sheesham cornice projecting approximately 75 mm, providing a balanced architectural appearance. |
| 36 | All internal cabinet carcasses, drawer boxes, shelves and concealed structural members shall be manufactured using 18mm & 12mm MR Grade Plywood, finished matching to outer surfaces using protective clear polish to coordinate with the external finish.All shutters shall be fitted with premium quality soft-close hinges, magnetic catchers, adjustable shelf supports, telescopic drawer channels, locks where required, concealed fixing accessories and all necessary hardware of approved make. Glass shutters shall be fitted with premium Brass hinges suitable for the weight of 8 mm bevelled glass.All exposed timber surfaces shall be machine sanded smooth, stained in Walnut Brown, sealed with two coats of wood sealer, and finished with premium satin melamine polish. Antique Brass finished handles, knobs and exposed metal support pipes shall have a durable lacquered finish. LED lighting shall include concealed drivers, wiring and all electrical accessories required for complete installation.The complete Crockery Unit shall be supplied, transported, assembled, installed and finished with all hardware, glazing, lighting, stone top, polishing and accessories complete in every respect, as approved by the Engineer-in-Charge. The work shall be complete as per given design, drawing and direction of Engineer-Incharge. |
| 37 | DINING TABLE |
| 38 | Providing, fabricating and Placing in position Restaurant Dining Table having overall size of 1600L × 800D × 750H mm, complete with 30 mm thick stone top (15 mm stone laminated over 15 mm edge moulding to achieve full thickness appearance) in approved ItalianMarble /Indian Marble/Quartz of approx Rs.800/sqft as selected by the Engineer In-Charge. The table top shall have rounded corner profile as shown in the approved design and shall be securely fixed over a 6 mm thick MS top plate of suitable size using stone adhesive and concealed mechanical fasteners. The MS top plate shall be finished in Black Matte Powder Coating after proper surface treatment.The table shall be supported on 02 nos. cylindrical pedestal legs made using Solid Sheesham Wood duly seasoned and chemically treated, each pedestal Ø200 mm dia and 700 mm high, fixed to the top plate with concealed MS fixing plates and heavy-duty fasteners. Each pedestal shall be mounted on a 10 mm thick MS base plate of approximately 450L × 350D mm with rounded corners covered with wood as per approved design and provided with concealed levelling nylon bushes to ensure stability and protect the flooring. The pedestal spacing shall be proportioned to provide adequate leg room and comfortable seating from all sides.All exposed solid wood surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The stone shall be polished and edge-finished to approved quality. All MS components shall be rust-proof treated before powder coating. The item shall include all necessary concealed hardware, fixing accessories, transportation, loading, unloading, installation, labour and all incidental works required for completing the table in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 39 | DINING TABLE |
| 40 | Providing, fabricating and Placing Restaurant Dining Table having overall size of 2100L × 900D × 750H mm, complete with 30 mm thick stone top (15 mm stone laminated over 15 mm edge moulding to achieve full thickness appearance) in approved ItalianMarble /Indian Marble/Quartz of approx Rs.800/sqft as selected by the Engineer In-Charge. The table top shall have rounded corner profile as shown in the approved design and shall be securely fixed over a 6 mm thick MS top plate of suitable size using stone adhesive and concealed mechanical fasteners. The MS top plate shall be finished in Black Matte Powder Coating after proper surface treatment.The table shall be supported on 02 nos. cylindrical pedestal legs made using Solid Sheesham Wood duly seasoned and chemically treated, each pedestal Ø200 mm dia and 700 mm high, fixed to the top plate with concealed MS fixing plates and heavy-duty fasteners. Each pedestal shall be mounted on a 10 mm thick MS base plate of approximately 450L × 350D mm with rounded corners covered with wood as per approved design and provided with concealed levelling nylon bushes to ensure stability and protect the flooring. The pedestal spacing shall be proportioned to provide adequate leg room and comfortable seating from all sides.All exposed solid wood surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The stone shall be polished and edge-finished to approved quality. All MS components shall be rust-proof treated before powder coating. The item shall include all necessary concealed hardware, fixing accessories, transportation, loading, unloading, installation, labour and all incidental works required for completing the table in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 41 | DINING TABLE ROUND |
| 42 | Providing, fabricating and Placing in position Restaurant Dining Table having overall size of 1200 dia × 750H mm, complete with 30 mm thick stone top (15 mm stone laminated over 15 mm edge moulding to achieve full thickness appearance) in approved Italian Marble/Indian Marble/Quartz of approx Rs.800/sqft as selected by the Engineer In-Charge. The table top shall have rounded corner profile as shown in the approved design and shall be securely fixed over a 6 mm thick MS top plate of suitable size using stone adhesive and concealed mechanical fasteners. The MS top plate shall be finished in Black Matte Powder Coating after proper surface treatment.The table shall be supported on 01 nos. of cylindrical pedestal leg made using Solid Sheesham Wood duly seasoned and chemically treated, pedestal Ø200 mm dia and 700 mm high, fixed to the top plate with concealed MS fixing plates and heavy-duty fasteners. The pedestal shall be mounted on a 10 mm thick MS base plate of approximately 450L × 350D mm with rounded corners covered with wood as per approved design and provided with concealed levelling nylon bushes to ensure stability and protect the flooring. The pedestal shall be centre positioned to provide adequate leg room and comfortable seating from all sides.All exposed solid wood surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The stone shall be polished and edge-finished to approved quality. All MS components shall be rust-proof treated before powder coating. The item shall include all necessary concealed hardware, fixing accessories, transportation, loading, unloading, installation, labour and all incidental works required for completing the table in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 43 | RESTAURANT SOFA |
| 44 | Providing, fabricating and Placing in position Restaurant Sofa of overall size 1800L × 700D × 900H mm, with 450 mm seating height, 550 mm seating depth and 450 mm high backrest above seat level, manufactured as per approved image/drawing.The sofa shall be constructed using seasoned and chemically treated solid hard wood internal framework. The seat frame shall be approximately 150 mm high, fabricated using solid wood members and reinforced with zig-zag springs and high-tensile elastic webbing to provide uniform weight distribution, enhanced seating comfort and long service life. The seat shall be upholstered with 100 mm thick, 32 density PU foam, providing an overall seat thickness of approximately 250 mm, finished in premium upholstery fabric of approved shade and quality having an approximate Min. MRP of Rs. 800 per metre.The backrest shall comprise a dual-layer wing-back design with gently curved side wings extending forward to provide enhanced lateral support. The backrest structure shall be manufactured using seasoned solid wood, flexible plywood and MR Grade plywood as per requirement, upholstered with 50 mm thick, 32 density PU foam on the inner face and 12 mm thick PU foam on the outer face. The inner backrest shall incorporate button tufted detailing as shown in the approved image, with neatly stitched upholstery.The exposed base frame shall be manufactured from Solid Sheesham Wood, comprising 50 × 28 mm frame members supported on 60 × 60 mm solid wood legs tapering to 45 × 45 mm at the bottom, providing an approximate 150 mm floor clearance. All exposed wooden surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer, followed by two coats of Melamine Satin Finish.All upholstery shall be neatly tailored with uniform stitching, rounded edges and wrinkle-free finish. The sofa shall be manufactured using traditional woodworking techniques with concealed joinery, premium adhesives and precision workmanship to ensure strength, stability and durability suitable for heavy commercial restaurant use.The rate shall include all materials, labour, transportation, handling, installation at site and incidental works, complete in all respects as per approved image/drawings and the directions of the Engineer-in-Charge. |
| 45 | RESTAURANT CHAIR |
| 46 | Providing, fabricating and Placing in position Restaurant Chair having overall size of 580L × 600D × 850H mm with seating height 450 mm, manufactured using Solid Sheesham Wood duly seasoned and chemically treated and upholstered as per approved design. The exposed wooden base frame shall be constructed using 45 × 30 mm Solid Sheesham Wood sections, rigidly joined with mortise and tenon joints, waterproof adhesive and concealed fasteners. The chair legs shall be made from 60 × 60 mm Solid Sheesham Wood with cylindrical profile, elegantly tapering to approximately 40 × 40 mm at the bottom, providing stability and a refined appearance. The exposed wooden frame shall continue around the seat base as shown in the approved design and shall be securely fixed to the upholstered shell.The upholstered seat shall be constructed on a Solid Sheesham Wood frame of size 60 × 30 mm. The seat base shall be supported using elastic webbing and zig-zag springs fixed over the wooden frame, covered with jute hessian cloth, cotton marking cloth at base and bonded using SR adhesive. The seat cushion shall have an overall thickness of approximately 105 mm, comprising 75 mm thick PU Foam of 32 density over the wooden seat frame, upholstered in premium upholstery fabric of approved make and shade of min. Rs. 800 per metre MRP, complete with neatly stitched seams and piping as required.The wrap-around backrest and integrated armrests shall form a single continuous upholstered shell, manufactured using 12 mm Flexible Plywood fixed over a solid wood support framework to achieve the required curved profile. The backrest shall extend 400 mm above the seat and the armrests shall rise 200 mm above the seat at the front, gradually merging into the curved back as shown in the approved design. The inner face of the backrest and armrests shall be padded with 40 mm thick PU Foam of 32 density, while the outer face shall be finished with 12 mm PU Foam to achieve a smooth and well-contoured appearance. All upholstery shall be neatly tailored with concealed stitching, maintaining uniform curves and wrinkle-free finishing. |
| 47 | All exposed Solid Sheesham Wood components shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The chair shall be provided with nylon buffers at the bottom of the legs and all necessary concealed hardware, screws and fittings. The cost shall include all materials, labour, transportation, loading, unloading, installation and incidental works required for completing the item in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 48 | SERVICE COUNTER |
| 49 | Providing, fabricating and Placing in position Restaurant Service Counter having overall size of 1200L × 600D × 900H mm, manufactured entirely using Solid Sheesham Wood duly seasoned and chemically treated, complete as per approved design. The counter shall be provided with a 15–18 mm thick Marble/Granite/Quartz stone top of Rs. 800 per sqft market value of approved make and shade, fixed over MR Plywood base with rounded corner profile as shown in the approved design. The stone top and edges shall be smoothly finished and polished.The main carcass shall be fabricated using Solid Sheesham Wood frame sections of 70 × 30 mm, with 18 mm thick solid wood panels for the sides, back, bottom and internal partitions. The front top fascia below the stone shall feature solid Sheesham wood fluted detailing approximately 100 mm high, formed using closely spaced rounded flutes of approximately 18mm diameter. The side corners of the cabinet shall have full-height rounded solid wood corner posts of approximately R40–50 mm radius, continuing seamlessly into the base moulding to match the approved design.The counter shall be provided with 02 nos. drawers of equal size, each approximately 350L × 450D × 120H mm, constructed entirely from 20 mm thick Solid Sheesham Wood, fitted with 450 mm telescopic drawer channels, 100 mm Stainless Steel handles, and concealed joinery. Below the drawers, the unit shall incorporate 04 nos. open storage shelves formed by 18 mm thick solid Sheesham wood shelves and vertical partitions, creating compartments of approximately 250 mm clear height, suitable for storage of restaurant service accessories. The base shall be constructed using 50 × 30 mm Solid Sheesham Wood framing and finished with a 100 mm high moulded solid wood skirting running continuously around the visible faces of the cabinet. All exposed front edges shall have rounded profiles, and all joints shall be accurately fitted using mortise and tenon joints, waterproof adhesive and concealed fasteners to ensure long-term structural stability. |
| 50 | All exposed solid wood surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The stone top shall be machine polished with finished edges. The counter shall be supplied complete with all necessary hardware, drawer channels, SS handles, nylon buffers, transportation, loading, unloading, installation, labour and all incidental works required for completing the item in all respects as per approved drawings and the directions of the Engineer In-Charge.The work shall be complete as per given design, drawing and direction of Engineer-Incharge. |
| 51 | Kids Restaurant High Chair |
| 52 | Kids Restaurant High ChairOverall Dimensions: 520 L × 610 D × 980 H mmProviding and Placing in position Kids Restaurant High Chair of overall size 520 L × 610 D × 980 H mm, manufactured from seasoned and chemically treated Solid Sheesham Wood, complete with upholstered seat and back cushion, safety restraint, footrest, food tray, polishing and all accessories, as per approved drawings and the direction of the Engineer-in-Charge.The chair shall be constructed with a rigid frame using Solid Sheesham Wood members. Front and rear legs shall be approximately 50 × 35 mm, tapering elegantly towards the floor while maintaining adequate structural strength. Side rails, arm supports, stretchers and tray support members shall be approximately 50 × 30 mm, securely joined using mortise and tenon joints, hardwood dowels and waterproof adhesive to ensure rigidity and long service life. All exposed corners and edges shall be rounded to a minimum R8-R10 radius for child safety.The chair shall have an overall seat height of approximately 650 mm from finished floor level. The seat shall measure approximately 340 mm wide × 320 mm deep and shall be manufactured from 18 mm thick Solid Sheesham Wood, upholstered with 40 mm thick high-density PU foam (32 Density) and finished in approved Fabric/PU Leatherette. The backrest shall be approximately 300 mm high, formed from 18 mm thick Solid Sheesham Wood, upholstered with 25–30 mm thick PU foam and finished in matching approved upholstery of approx 800 per metre MRP.The chair shall be provided with an integrated Solid Sheesham Wood feeding tray having an overall depth of approximately 380 mm and an internal usable width of approximately 460 mm. The tray shall have smoothly rounded corners and raised edge profile to prevent utensils and food items from slipping. The tray shall be securely fixed to the arm supports forming a rigid safety enclosure.A footrest shall be provided approximately 350 mm above floor level, manufactured from Solid Sheesham Wood members securely housed into the frame to improve child comfort and structural stability. The chair shall also be provided with a heavy-duty adjustable safety strap with quick-release buckle securely fixed beneath the seat to safely restrain the child during use. |
| 53 | CAFÉ SERVING COUNTER |
| 54 | Providing,fabricating and placing in position Cafe Counter having overall dimensions of approx 4800 L × 700 D × 900 H mm, fabricated using seasoned and chemically treated Solid Sheesham Wood and Sheesham Veneered Plywood, complete with Premium Stone Counter top, premium hardware, polishing and all accessories as per approved image/ drawings. The contractor shall verify dimensions at the site before commencement of fabrication. The counter shall comprise a rigid solid wood structural framework fabricated using 50 × 30 mm Solid Sheesham Wood members with intermediate verticals and horizontal rails adequately spaced to prevent deflection. All exposed framework, front face framing, mouldings, skirting, drawer facias, edge members and trims shall be manufactured from Solid Sheesham Wood, while all concealed carcass members, internal partitions, shelves and drawer boxes shall be made from 18mm MR Grade Plywood with veneer face. All internal plywood surfaces shall be finished matching to exposed outer surfaces in approved wood shade. The countertop shall consist of 15 mm thick Indian/Italian Marble of approx Rs.800/sqft in approved variety, fixed over 18 mm thick MR Grade Plywood, with edge build-up to provide an overall visible thickness of approximately 30 mm. The stone shall project approximately 25 mm beyond the front and side faces with neatly polished exposed edges.The front facia shall be designed as a decorative architectural elevation comprising five equal recessed framed panels, each approximately 900–930 mm wide, formed with 40 mm wide × 25 mm thick Solid Sheesham moulded framing surrounding veneered centre panels. Vertical corner posts and intermediate stiles shall be approximately 75 mm wide, with a continuous moulded top rail below the stone and a 100 mm high recessed Solid Sheesham skirting, set back approximately 50 mm to provide a floating appearance and protection against impact. A concealed Warm White LED strip shall be provided below the stone overhang to softly illuminate the front facia. |
| 55 | The service side shall be arranged for efficient café operation and shall comprise 8 equal top drawers, each approximately 550 mm wide and 150–180 mm high, fitted with framed Solid Sheesham drawer facias, heavy-duty full-extension telescopic channels, and 150 mm long Antique Brass finish handles of approved design. Below the drawers, the centre portion shall consist of continuous open shelving divided into practical storage bays by 18 mm thick vertical solid wood partitions, with one intermediate adjustable shelf creating two storage levels suitable for crockery, cups, trays and café accessories. The extreme left and right end bays shall be enclosed with single-door storage cabinets, each fitted with one adjustable shelf inside. Cabinet shutters shall be framed in Solid Sheesham Wood with veneered infill panels and shall be provided with heavy duty butt hinges, magnetic catchers and Antique Brass handles matching the approved hardware.All exposed timber surfaces shall be machine sanded smooth, stained in Walnut Brown, sealed with two coats of wood sealer, and finished with premium satin melamine polish. All internal surfaces shall receive a matching finish with Melamine polish. The counter shall be complete with all necessary hardware including hinges, telescopic drawer channels, shelf supports, locks, concealed fasteners, levelling blocks and all accessories necessary for satisfactory installation and operation, complete in every respect, as approved by the Engineer-in-Charge.The cost shall include all materials, labour, handling, transportation and installation complete in all respects as per the direction of Engineer In-charge.The work shall be complete as per given design, drawing and direction of Engineer-Incharge. |
| 56 | CAFÉ BAR COUNTER (BACK WALL UNIT) |
| 57 | Providing,fabricating and placing in position Back Bar Counter with Wall Mounted Display UnitOverall DimensionsBase Counter Unit: 4800 L × 500 D × 900 H mmClear Working Gap: 500 mmWall Mounted Display Unit: 4800 L × 350 D × 1400 H mmProviding, fabricating and fixing Back Bar Counter with Wall Mounted Display Unit of above dimensions, fabricated using seasoned and chemically treated Solid Sheesham Wood, Sheesham Veneered Plywood, complete with premium stone countertop, hardware, LED lighting, polishing and all accessories, as per approved drawings and the directions of the Engineer-in-Charge.The contractor shall verify all dimensions at site before fabrication.The complete assembly shall comprise a Base Storage Counter, 500 mm clear working space, and a Wall Mounted Display Unit, forming one integrated Back Bar system.Base Counter Unit : The base counter shall measure 4800 L × 500 D × 900 H mm and shall be constructed with a rigid framework of 50 × 30 mm seasoned Solid Sheesham Wood members with adequate intermediate supports. All exposed framework, face frames, mouldings, skirting and edge members shall be of Solid Sheesham Wood. Shutter panels and exposed side panels shall be fabricated from 18 mm Sheesham Veneered Plywood, while all carcasses, partitions, shelves, backs and concealed members shall be of 18 mm MR Grade Plywood with veneer finish matching the external surfaces.The front elevation shall comprise eight single shutters, each approximately 500–550 mm wide, framed in Solid Sheesham Wood with veneered infill panels, complete with premium quality soft-close hinges, approved handles and all necessary hardware.The countertop shall comprise 15 mm thick Indian/Italian Marble (approx. ₹800/sq.ft.) fixed over 18 mm MR Grade Plywood, with edge build-up to provide an overall visible thickness of approximately 30 mm and a 25 mm projection beyond the cabinet face. The unit shall be provided with a 100 mm high recessed plinth/skirting. |
| 58 | Wall Mounted Display Unit : The wall mounted Bar Unit shall measure 4800 L × 350 D × 1400 H mm.The exposed framework shall be manufactured from Solid Sheesham Wood. Side panels, cabinet shutters and exposed end panels shall be made from 18 mm Sheesham Veneered Plywood, while the carcass, top, bottom, back panels and concealed members shall be manufactured from 18 mm MR Grade Plywood finished with matching veneer finish. The centre portion shall comprise four shutters forming two double-door cabinets, each shutter measuring approximately 450-500 mm wide. Each cabinet shall be provided with two adjustable shelves, creating three storage levels.Both the left and right end portions shall comprise open wine bottle display shelving constructed using Solid Sheesham Wood framing with 18 mm thick Sheesham Veneered Plywood vertical partitions and carcass members. Horizontal display shelves shall be manufactured from 8 mm thick clear toughened glass, supported on stainless steel L-type shelf brackets securely fixed to the wooden side panels and vertical partitions. Display niches shall measure approximately 250 mm (W) × 400 mm (H), proportioned as per the approved drawing. All exposed edges shall be finished Solid Sheesham lipping profiles.Concealed Warm White LED strip lighting shall be integrated within each display compartment to illuminate the bottles uniformly. An additional concealed LED strip shall be provided below the bottom rail of the wall unit to illuminate the working counter surface.All Solid Sheesham Wood shall be well seasoned and chemically treated. Exposed veneered components shall be 18 mm Sheesham Veneered Plywood, while concealed structural members shall be 18 mm MR Grade Plywood with matching veneer finish.The glass shelves shall be 8 mm thick clear toughened glass with polished edges, securely supported on stainless steel L-type shelf brackets fixed to the timber framework.All shutters shall be fitted with premium quality SS hinges, magnetic catchers, shelf supports, approved metal handles and all necessary fixing hardware. All exposed timber surfaces shall be machine sanded, stained in Walnut Brown or approved shade, sealed with two coats of wood sealer, and finished with premium Satin Melamine polish. Internal veneered surfaces shall receive the same matching Melamine finish. The rate shall include all Solid Sheesham Wood, Sheesham Veneered Plywood, MR Grade Plywood, 8 mm toughened glass shelves, stainless steel shelf brackets, stone top, LED lighting with drivers, hardware, polishing, labour, transportation, installation, testing, commissioning and all incidental works, complete in all respects as approved by the Engineer-in-Charge. |
| 59 | BAR CHAIR |
| 60 | Providing, fabricating and Placing in position Café Bar Chair of overall size 550 mm (L) × 580 mm (D) × 950 mm (H) with a seat height of 650 mm, manufactured in contemporary café style as per approved design and drawing. The complete exposed framework shall be made from first quality Solid Sheesham Wood, thoroughly seasoned to moisture content not exceeding 12% and chemically treated against termites, borers and fungal attack. The chair shall comprise front legs of finished section 45 × 45 mm, tapering gracefully towards the bottom, rear legs extending continuously into the back support in 40 × 45 mm finished section, side seat rails 30 × 70 mm, front and rear seat rails 30 × 75 mm, and footrest/stretchers of 25 × 40 mm finished section, rigidly connected using mortise and tenon joinery, waterproof adhesive and concealed fasteners to withstand heavy commercial café usage. The upholstered seat shall be constructed using 12 mm thick commercial plywood fixed over the solid wood seat frame and provided with 75 mm thick, 32 density high resilience PU foam, while the fully upholstered wrap-around curved backrest shall be fabricated using 12 mm thick shaped plywood with 25 mm thick, 32 density PU foam, ergonomically contoured to provide comfortable lumbar and arm support. The chair shall be upholstered in premium upholstery fabric of approved quality of selected shade, texture and pattern of min. Rs.800/- per mtr MRP, neatly tailored with concealed stitching and wrinkle-free finish. All exposed timber surfaces shall be machine sanded smooth and finished in approved stain colour followed by sealer coats and multiple coats of premium PU matt finish, providing a durable, moisture-resistant and scratch-resistant surface suitable for hospitality applications. The chair shall be provided with heavy-duty nylon floor protectors to all legs to prevent damage to finished flooring and reduce operational noise. The item shall include all solid Sheesham wood, plywood, PU foam, upholstery fabric, adhesives, polishing, hardware, labour, transportation, assembly and installation, complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge. |
| 61 | CAFÉ ROUND DINING TABLE |
| 62 | Providing, fabricating and Placing in position Café Round Dining Table of overall size 1000 mm Diameter × 750 mm Height, as per approved design. The table shall have a 30 mm thick stone top, comprising 15 mm natural stone (Italian Marble/Engineered Stone/Quartz as approved of Rs. 800/- per sqft market value) with 15 mm edge moulding, machine polished on all exposed edges. The supporting structure shall be manufactured from Solid Sheesham Wood, duly seasoned and chemically treated. The table shall have a tapered conical pedestal of approximately Ø230 mm at the bottom reducing to Ø140 mm at the top, securely fixed to the top with concealed steel plate of thickness 10 mm and dia 300mm. The base shall consist of a 450 mm diameter solid Sheesham wood platform of 45 mm overall thickness with moulded profile, designed to provide adequate stability for commercial use. All timber members shall be accurately machined with concealed joinery and waterproof adhesive. Exposed wooden surfaces shall be finished in approved Walnut Brown shade using wood stain, two coats of sealer and Satin Finish Melamine polish. Nylon floor protectors and other necessary hardware to be provided. The cost is including material, labour, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 63 | CAFÉ CHAIR |
| 64 | Providing, fabricating and Placing in position Café Lounge Chair of overall size 550L × 600D × 800H mm with seat height 480 mm, manufactured in modern contemporary design as per approved drawing. The complete exposed wooden framework including front legs, rear legs, armrests, backrest frame and seat support frame shall be made from first quality Solid Sheesham Wood, thoroughly seasoned to moisture content not exceeding 12% and chemically treated against termites, borers and fungal attack. The front legs shall be of finished section approximately 45 × 45 mm, tapering elegantly towards the floor, while the rear legs shall continue seamlessly into the back support frame in a single flowing member of approximately 45 × 35 mm section. The top curved arm and backrest rail shall be formed from laminated or steam-bent solid Sheesham wood of finished section approximately 55 × 30 mm, maintaining smooth flowing curves without visible joints or sharp edges. The intermediate side support members below the armrest shall be of approximately 35 × 25 mm section, and the seat bottom frame shall be constructed from solid Sheesham members of minimum 40 × 30 mm section with additional concealed cross rails for rigidity and long-term structural stability. All timber members shall have machine-rounded edges, precision joinery using mortise and tenon joints reinforced with waterproof adhesive and concealed mechanical fasteners to ensure a rigid and wobble-free construction. The seat shall be upholstered with 75 mm thick, 32-density high resilience polyurethane foam of sleepwell or equivalent make, while the inside face of the backrest shall be upholstered with 25 mm thick, 32-density polyurethane foam, both covered in approved premium quality upholstery fabric of selected shade, texture and pattern of min. Rs. 800/- per metre MRP. Upholstery shall be neatly tailored with wrinkle-free finishing and concealed stapling. The exposed timber surfaces shall be machine sanded smooth and finished in approved stain colour followed by two coats of sealer and multiple coats of premium PU matt finish to provide a durable, scratch-resistant and moisture-resistant surface. Plastic nylon floor protectors shall be provided below all legs to prevent damage to finished flooring. The item shall include all materials, solid seasoned Sheesham wood, upholstery fabric, PU foam, adhesives, hardware, polishing, labour, transportation, assembly, finishing and installation, complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge. |
| 65 | CAFÉ LOUNGE SOFA |
| 66 | Providing, fabricating and Placing in position Cafe Lounge Sofa (3 Seater) of overall size 1800 mm (L) × 700 mm (D) × 830 mm (H) with seating height of 430 mm, seat depth of 600 mm, backrest height of 400 mm above seat, and armrest height of 200-250 mm at the lowest point, manufactured as per approved design and drawing. The exposed structural framework, legs and base shall be fabricated from Solid Sheesham Wood, duly seasoned and chemically treated against termites and borers. The sofa shall comprise legs of 45 × 45 mm finished section tapered to 35 × 35 mm, base rails of 30 × 75 mm section, side rails of 30 × 60 mm section, back support members of 30 × 50 mm section, and curved arm and back framework formed from laminated solid Sheesham sections of approximately 35 × 60 mm, rigidly joined using mortise and tenon joints, waterproof adhesive and concealed fasteners.The seat shall be constructed on an independent Solid Sheesham Wood frame of 65 × 28 mm section, fitted with elastic webbing and zig-zag springs to provide proper resilience and seating comfort. The upholstered seat shall consist of 125 mm thick, 32 density PU Foam over the spring base, giving a well-contoured seating profile. The backrest and wrap-around armrest shall be constructed using 6 mm MR Grade Plywood fixed to the solid wood framework and upholstered with 50 mm thick, 32 density PU Foam, maintaining the continuous curved profile shown in the approved design. Upholstery work shall include jute hessian cloth, cotton marking cloth, SR adhesive, stitching and all necessary upholstery accessories complete in all respects.The sofa shall be upholstered in Premium Upholstery Fabric of approved shade and texture of min. ₹800/- per metre MRP, neatly tailored with concealed stitching and wrinkle-free finish. All exposed wooden surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Melamine Top Coat. The sofa shall be provided with nylon bushes to the underside of legs for floor protection. The item shall include all solid wood, plywood, PU foam, upholstery fabric, polishing, hardware, labour, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 67 | COFFEE TABLE |
| 68 | Providing, fabricating and Placing Cafe Lounge Centre Table having overall size of 1500L × 750D × 450H mm, manufactured using Solid Sheesham Wood duly seasoned and chemically treated. The table shall be provided with a 15–18 mm thick Marble/Quartz stone top of min. ₹800/- per sqft approved make, pasted over 18 mm thick MR Grade Plywood base with machine-polished edges. The stone top shall remain suspeded with a wooden frame grooving profile of 15mm on all sides.The supporting frame shall be made using 90 × 28 mm Solid Sheesham Wood with recessed panel detailing and carved corner detailing as per approved design. The top shall be reinforced with 50 × 30 mm Solid Sheesham Wood cross members. The table shall be supported on 90 × 90 mm Solid Sheesham Wood legs, tapering down to 65 × 65 mm, securely joined to the frame using mortise and tenon joints and concealed fasteners.All exposed wood surfaces shall be finished in Walnut Brown shade using approved wood stain, two coats of wood sealer and Satin Finish Melamine polish. The table shall be complete with nylon buffers, all necessary hardware, transportation, installation, labour and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 69 | Curved Lounge Sofa |
| 70 | Providing and placing in position Curved Lounge 4 seater Sofa of Overall dimensions 2985/1925 (L) × 750 (D) × 730 (H) mm. The sofa shall be of semi circular shape, suitable for restaurants, cafés, lounges. The overall construction shall comprise a seasoned and chemically treated hardwood/ Sheesham Wood for internal framework with all structural members securely joined using mortise-and-tenon, dowels, screws and high-strength adhesive to ensure rigidity, durability and long service life. The seat platform shall be fabricated from 18 mm Commercial Grade plywood adequately reinforced with hardwood members.The seat height shall be 430 mm from finished floor level. The seat shall be provided with 120 mm thick high-density polyurethane foam 32vdensity firmly bonded to the base frame to provide long-lasting comfort and shape retention. The clear seating depth shall be 600 mm.The backrest shall be 300 mm high above the seat level and ergonomically curved to match the sofa profile. It shall be padded on both the inner seating face and the top surface with 75 mm thick high-density polyurethane foam, providing continuous lumbar support and comfortable seating. The outer back shall be smoothly contoured with appropriate padding of 12mm foam to achieve a premium upholstered finish.The sofa shall be completely upholstered in approved fabric or PU leatherette of approved colour and texture, having a min. MRP of ₹800 per running metre, fixed neatly with concealed stitching wherever applicable. Upholstery shall be wrinkle-free, uniformly tensioned and finished with clean seams. The sofa shall be provided with a continuous 80 mm high base skirting, finished in approved wood shade finish. The base shall be fitted with heavy-duty nylon levelling glides to prevent direct contact with the finished floor surface.All exposed edges shall be smooth, uniformly finished. All exposed wooden surfaces will be polished using stain, two coats of sealer and two coats for Melamine Satin Finish as top coat. The rate is inclusive of all taxes, materials, labour, transportation, handling, installation and all incidental works as may be required for completion. The item must be completed in all respects as per the direction of Engineer In-charge. |
| 71 | Round Coffee Table |
| 72 | Fabricating and placing in position of Round Coffee Table of Overall dimensions 900 mm Diameter × 550 mm Height, as per approved drawing/reference image. The table shall be of contemporary minimalist design with a circular top supported on a centrally positioned four-fin pedestal base, suitable for restaurants, cafés and lounges. The complete table shall be manufactured using seasoned and chemically treated Solid Sheesham Wood and Sheesham Veneered Commercial Grade Plywood, ensuring structural stability, dimensional accuracy and long service life.The table top shall be 36 mm thick, fabricated from 18 mm thick Sheesham Veneered Commercial Grade Plywood with an 18 mm thick Solid Sheesham Wood edge build-up securely bonded around the entire perimeter to achieve a monolithic appearance. The edge shall be machine-finished with a soft eased profile and perfectly flush with the veneered surface.The pedestal shall comprise four interlocking Solid Sheesham Wood fins, each 36 mm thick, arranged symmetrically at 90° to form a cross configuration. The members shall be securely joined using concealed interlocking joints, mortise-and-tenon joints, hardwood dowels, screws and high-strength adhesive to provide a rigid, self-supporting structure. The pedestal shall be centrally fixed to the underside of the tabletop using concealed fasteners and designed to provide maximum stability with adequate leg clearance for users.The table shall be provided with heavy-duty nylon levelling glides. All joints shall be tight-fitting, accurately aligned and free from visible gaps or defects. The completed assembly shall be stable, free from wobble and suitable for heavy-duty commercial use.All exposed edges shall be smooth and uniformly finished. All exposed wooden surfaces shall be finished with an approved wood stain, followed by two coats of sealer and two coats of Melamine Satin Finish as the final protective coat, producing a smooth, scratch-resistant and moisture-resistant finish while retaining the natural grain of the Sheesham wood and veneer.The rate shall be inclusive of all materials, Solid Sheesham Wood, Sheesham Veneered Commercial Grade Plywood, hardware, adhesives, wood preservative treatment, polishing, labour, transportation, handling, installation, levelling, taxes and all incidental works required for complete execution of the item.The item shall be completed in all respects, strictly in accordance with the approved drawings, specifications and the directions of the Engineer-in-Charge. |
| 73 | POOL TABLE |
| 74 | Providing and fixing of Pool Table of overall size of 2590Lx1470Dx800H mm having playing surface size of 2240x1120 mm. Comes with 4 corners & 2 Side Pockets. Table Bed With Natural slate bed of thikness 19mm supported by wooden frame. Comes with standard quality rubber cushions with laminated top. Side Rail Height 35-40mm. Table bed wiil be covered with good quality felt cloth in Green shade. Table structure made in solid wood with Melamine polish in Walnut Shade. Standard accessories included with pool table : 01 nos pool ball set, 4 nos Ashwood pool cues, 01 nos pool triangle, chalk set, cue tip , level adjusters, table brush, table dust cover, cue stand. Complete as per approval and direction of Engineer Incharge. |
| 75 | TT TABLE |
| 76 | Providing and fixing of TT Table Model : Stag Championship or equivalent having overall size of 2740Lx1525Dx760H mm. Top Thickness 22mm made of laminated particle board. Frame size 25x40mm. Wheel size 75mm. No of wheels - 02 with locks & 06 without locks. Paint Dupont PU Anti Glare coating on top. Accessories included are 2 TT Rackets, 6 Balls, a table cover & clamp net. Complete as per approval and direction of Engineer Incharge. |
| 77 | CARROM TABLE |
| 78 | Providing and placing in position of Carrom Table of size 900Lx900Dx760H mm with professional size Carrom Board with playing surface of approx 730x730 mm. The Table top outer frame 85x50 mm & pedestal pillar 120mm dia and base plate 300 mm dia are all made with Sheesham Wood duly seasoned and chemically treated. The Table top outer frame 85x40 mm shall have PU leather inserts for hand support and coin holders on all for corners. All wood surfaces duly finished using wood stains, wood sealers and Melamine polish in Walnut Shade as approved. The overall board size including the frame is 900 mm square and the board is mounted on a sturdy stand to achieve a playing height of about 750 mm from the floor. The playing surface is made from high-quality plywood finished with a smooth low-friction polish to ensure fast and consistent striker movement. The frame and stand are made from solid hardwood. The board features four corner pockets of approximately 45–50 mm diameter, fitted with nets or collectors beneath. Standard black boundary lines, base circles, arrows, and a central decorative design are precisely screen-printed according to tournament norms. The table is designed to be rigid, vibration-free and well-balanced suitable for professional and formal recreational settings.Complete as per approval and direction of Engineer Incharge. |
| 79 | CHESS TABLE |
| 80 | Providing and placing in position of Chess Table of overall size 750 L × 750 D × 750 H mm with removable professional-size Chess Board measuring 500 × 500 mm, divided into 64 equal squares, each measuring 57 × 57 mm. The table shall be manufactured using seasoned and chemically treated Solid White Ash Wood. The table top shall be 28 mm thick, supported on an 85 × 28 mm solid wood apron/frame, with 85 × 85 mm Solid White Ash legs tapering down to 60 × 60 mm, ensuring excellent rigidity and stability.The table top shall incorporate a removable chess board insert, allowing easy replacement and maintenance. The overall table top, including the surrounding border, shall measure 750 × 750 mm, providing adequate resting space around the playing surface. The chess board shall be crafted from premium hardwood or veneered substrate in contrasting light and dark tones with a smooth, low-glare protective finish suitable for professional play.The table shall be provided with two drawers, each approximately 350 mm long, located on opposite sides for convenient storage of chess pieces and accessories. The supporting structure shall be designed for vibration-free performance and long-term durability, suitable for professional tournaments as well as formal recreational use.All exposed timber surfaces shall be machine sanded smooth and finished with two coats of wood sealer followed by premium satin melamine polish. Wood finish shall match the approved reference image or as approved by the Engineer-in-Charge.The item shall be complete with all materials, labour, hardware, transportation, installation and finishing, complete in all respects, as approved and directed by the Engineer-in-Charge. |
| 81 | FOOS BALL TABLE |
| 82 | Providing and placing in position of STAG GLOBAL Flex Indoor Foosball Table of size 1500X730X880 mm, Crafted from high-quality engineered wood with a sturdy undercarriage to withstand intense matches.Features built-in cup holders at the corners, allowing players to keep drinks safe and accessible during play.Equipped with chrome-plated steel rods and ergonomic non-slip handles for precise player control and high-speed shots.Includes precision leg levelers to ensure a perfectly flat playing surface, even on uneven floors.Includes an abacus-style score counter, center ball drop for fair starts, and side ball-return pockets for continuous action.Designed for family fun and Indoor play, this high-quality table features integrated cup holders, centre ball drops on both ends, and adjustable leg levellers for fair and seamless gameplay. Equipped with ball return pockets, quiet padded goal boxes, and abacus-style score counters, it ensures fast, organized play. The powder-coated steel legs fold easily for compact storage, and the table comes with a weatherproof cover and durable resin balls—making it perfect for indoor entertainment complete as per directions of Engineer-In-Charge. |
| 83 | AIR HOCKEY TABLE |
| 84 | Providing and placing in position of Arcade size air hockey table of size 2150x1080x810 mm with electronic scorer and display of Blueline or equivalent make. MDF playing field surface with a white high-gloss PVC finish, Sturdy box legs with full panel supports, Premium motor and high gloss play field produce fast puck action, Pushers and pucks included, Playfield Material : Acrylic, Scoring Type : Electronic Score, Side aprons: PB, 17cm wide, End aprons: MDF, complete as per directions of Engineer-In-Charge. |
| 85 | OUTDOOR DINING TABLE |
| 86 | Outdoor Dining Table - Providing, fabricating and Placing Outdoor Round Dining Table of overall size 1200 mm Dia × 750 mm Height, comprising a premium natural stone top (Banswara White or equivalent white Marble) supported on a heavy-duty mild steel pedestal base, complete in all respects as per approved drawing and the directions of the Engineer In-Charge. The table top shall be manufactured using natural Stone of approved variety, comprising 15 mm thick stone laminated with 15 mm thick matching edge moulding to achieve a solid 30 mm thick appearance. The stone shall have machine-polished top surface with neatly finished and rounded edge profile, and all exposed edges shall be mirror polished. The underside of the stone shall be reinforced with concealed MS fixing plates and suitable structural adhesive wherever required to ensure long-term rigidity and safe usage in outdoor conditions. The supporting pedestal shall be fabricated from heavy-duty Mild Steel (MS) comprising a 150 mm diameter cylindrical pedestal fabricated from 3.0 mm thick MS pipe, welded to 8 mm thick MS top fixing plate and a 500 mm diameter circular base plate fabricated from 10 mm thick MS plate to provide excellent stability against overturning. All welding joints shall be continuously welded, ground smooth and finished without visible imperfections. The complete MS framework shall undergo proper surface preparation, rust removal and anti-corrosion treatment followed by zinc-rich metal primer and finished with premium polyester powder coating in Black Matt finish of approved shade and texture, suitable for exterior exposure and resistant to weathering, moisture, corrosion and abrasion. The pedestal shall be securely fixed to the stone top using concealed fasteners, threaded inserts and structural epoxy adhesive, and the base shall be provided with adjustable heavy-duty nylon levelling bushes to compensate for uneven flooring while protecting finished surfaces. The item shall include all MS fabrication, natural stone, polishing, powder coating, concealed hardware, fasteners, adhesives, levelling bushes, labour, transportation, loading, unloading, installation and all other incidental works required for complete installation. The Outdoor Round Dining Table shall be completed in all respects as per the approved drawings, specifications and the directions of the Engineer In-Charge. |
| 87 | OUTDOOR DINING CHAIR |
| 88 | Outdoor Chair - Providing, fabricating and Placing in position Outdoor Dining Chair of overall size 500 mm (L) × 550 mm (D) × 800 mm (H) with seat height of 450 mm, manufactured as per approved design and drawing. The chair frame shall be fabricated from 25 mm dia Round Mild Steel (MS) Pipe of suitable thickness, fully welded and finished with Black Matt Polyester Powder Coating over suitable anti-corrosion treatment. The backrest and armrest shall be woven using Premium Outdoor Grade Polyester Braided Rope of approved colour and pattern, securely fixed to the MS frame. The seat shall be provided with 50 mm thick, 32 density PU Foam upholstered in Premium Outdoor Grade Fabric of approved shade. The loose back cushion shall be filled with high-quality Polyfill Fibre and upholstered in matching outdoor grade fabric. The chair shall be provided with nylon bushes to the bottom of legs for floor protection. The item shall include all materials, hardware, rope weaving, powder coating, upholstery, fabrication, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 89 | SERVICE COUNTER |
| 90 | Providing, fabricating and placing Serving Counter of overall size 2400 L × 600 D × 750 H mm, fabricated using 18 mm thick seasoned and chemically treated Solid Sheesham Wood throughout, complete with Black Granite countertop, polishing, hardware and all accessories, as per approved drawings and the directions of the Engineer-in-Charge.The counter shall be of rigid construction comprising 18 mm thick Solid Sheesham Wood overall used on side panels, top framing, bottom, back panel, vertical partitions, intermediate shelves and front framing, reinforced with an internal structural framework of 50 × 30 mm Solid Sheesham Wood members to ensure adequate strength, rigidity and long service life.The counter shall consist of three equal open storage bays, each approximately 760 mm wide, separated by full-height solid wood partitions. Each bay shall be provided with one fixed intermediate shelf, creating two storage levels suitable for crockery, serving articles, trays and other pantry accessories. All shelves shall be housed into the side panels and partitions using traditional housed joints and concealed fasteners.The countertop shall comprise 18 mm thick MR Grade Plywood base finished with 20 mm thick polished Black Granite of approved quality (approximate value Rs.500/sq.ft.), with polished exposed edges and an overhang of approximately 20–25 mm on the front and sides.A 100 mm high recessed solid wood plinth/skirting shall be provided at the bottom. All exposed timber surfaces shall be machine sanded smooth, stained in Walnut Brown or approved shade, sealed with two coats of wood sealer, and finished with two coats of premium Satin Melamine polish. The complete unit shall be free from cracks, warping, sharp edges and visible fixing marks.The rate shall include all Solid Sheesham Wood, Black Granite, polishing materials, labour, transportation, loading, unloading, installation, taxes and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 91 | STANDARD ROOM BED – KING SIZE WITH UPHOLSTERED HEADBOARD (WITHOUT STORAGE)Providing, fabricating and placing Standard Room Bed having overall size suitable to accommodate a 72\\" × 78\\" (1830 × 1980 mm) mattress KING size. The overall headboard length shall be 3110 mm, headboard height shall be 1200 mm, and the bed base shall measure 1910 mm (W) × 2020 mm (L) excluding the headboard, with an overall length of 2100 mm including the headboard. The overall bed base height shall be 350 mm from finished floor level. The bed shall be manufactured using seasoned and chemically treated Solid Sheesham Wood, MR Grade Plywood, and Sheesham Veneered Plywood, complete in all respects.The headboard shall comprise a centrally positioned upholstered panel aligned with the mattress width and flanked by decorative CNC Fluted side panels. The upholstered panel shall be fabricated using 18 mm MR Grade Plywood with 50 mm thick high-density PU Foam and premium upholstery fabric of min. Rs.800 per metre MRP as approved by the Engineer-in-Charge. The headboard shall have a finished edge profile thickness of 40 mm. The decorative side panels on both sides shall each be 600 mm wide, matching the width of the bedside cabinets, and shall be manufactured using 18 mm thick Sheesham Veneered Plywood with precision vertical fluted groove detailing. All exposed panel edges shall be finished with 40mm thick Solid Sheesham wood lipping, accurately machined, glued and finished flush with adjoining surfaces.The bed base for mattress shall be of overall height of 350 mm with Frame height 200mm and skirting height 150mm. Fabricated using 28 mm thick Solid Sheesham Wood, with the visible frame built up to an overall finished thickness of 40 mm by providing additional solid wood lipping. |
| 92 | The mattress support platform shall consist of 12 mm thick MR Grade Plywood securely fixed over 40 mm × 20 mm Solid Wood battens fastened to the inside of the main frame to provide continuous and uniform support for the mattress.The bed shall feature a recessed plinth/skirting on the front and both side elevations to create a floating cantilever appearance. The recessed skirting shall be 150 mm high, manufactured from 28 mm thick Solid Sheesham Wood, and set back 100 mm from the outer face of the bed frame on all three visible sides.The complete bed structure shall be designed as a knock-down assembly for ease of transportation, installation and future maintenance. Assembly shall be achieved using heavy-duty metal corner brackets fixed internally to ensure rigid, vibration-free performance without visible external hardware.The bed shall be without any storage provision, drawers, hydraulic lift-up mechanism or under-bed compartments.The bed shall be suitable to accommodate a 72\\" × 78\\" (1830 × 1980 mm) mattress. The recommended mattress thickness shall be 200 mm (8 inches).All exposed Solid Sheesham Wood and veneered surfaces shall be machine sanded smooth, stained in Walnut Brown shade, sealed with two coats of wood sealer, and finished with premium satin melamine polish. The cost shall include all materials, labour, handling, transportation, installation, complete in all respects as per approved drawings /specifications and directions of Engineer In-charge. |
| 93 | BEDSIDE CABINET |
| 94 | Providing, fabricating and Placing Bedside Cabinet of overall size 600L × 400D × 500H mm, comprising 02 drawers with fluted detailing as per approved image/drawing. The Bedside Cabinet shall be manufactured using 18 mm thick Sheesham Veneered Plywood for top, sides, bottom and internal carcass members, with 12 mm thick MR Grade Plywood back panel. Drawer boxes shall be made using 18 mm thick MR Grade Plywood for sides and back, with 9 mm thick MR Grade Plywood bottom securely housed in grooves.The cabinet shall be supported on Solid Sheesham Wood tapered legs of 40 × 40 mm section, interconnected with a 40 × 28 mm solid wood base framework. The unit shall provide an approximate 62 mm floor clearance for ease of cleaning. Drawer front facias shall be made in Solid Sheesham Wood approximately 180 mm high, featuring vertically fluted detailing as shown in the approved design. Drawers shall operate on heavy-duty telescopic channels of approved make and shall be fitted with black powder-coated metal edge profile handles recessed along the top edge of each drawer front.All exposed timber surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer, followed by two coats of Melamine Satin Finish. Internal plywood surfaces shall receive matching melamine finish.All exposed edges shall be neatly finished and hardware fixed true to line and level.The rate shall include all materials, labour, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 95 | LOOSE SEAT WITH 2 BOLSTERS & 2 CUSHIONS |
| 96 | Providing, fabricating and Fixing at site Seating on stone seating platform, comprising 02 Loose Seat Cushions of approx size 1100x700 mm each, 02 Cylindrical Bolsters and 02 Loose Back Cushions, complete in all respects as per approved drawing and fabric selection.The seating shall consist of 02 independent loose seat cushions, each approximately 150 mm thick, manufactured with high-resilience PU Foam of 32 Density over a suitable non-woven protective wrap to provide firm yet comfortable seating. The cushions shall be proportioned to suit the site-constructed stone platform with accurately tailored edges and concealed zipper opening for ease of maintenance. The underside shall be provided concealed hook-and-loop (Velcro) fixing arrangement to prevent movement during use.The set shall include 02 cylindrical bolster cushions, each approximately 600 mm long × 150 mm diameter, filled with high-density PU Foam core and upholstered in matching approved fabric. Bolsters shall be finished with circular end panels, concealed zip opening and neatly tailored stitching.The set shall also include 02 loose back cushions of size 450 × 450 mm, filled with premium virgin polyester polyfill fibre of approximately 800–1000 grams per cushion to provide soft back support. Cushions shall be finished with concealed zipper opening, neatly stitched piping along all edges and removable covers for cleaning.All upholstery shall be carried out using approved upholstery fabric of specified shade, texture and quality of min. Rs. 800/- per mtr MRP. All complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 97 | WALL UNIT WITH DESK , TV UNIT & LUGGAGE RACK |
| 98 | Providing, fabricating and Fixing in position Wall Mounted TV Unit with Study Table and Luggage Rack having an overall wall coverage of approximately 4000 mm, manufactured using traditional wood working techniques as per approved drawings. The unit shall comprise 03 independent modules, namely Study Table (1200L x 500D x 750H mm), Wall Mounted TV Ledge (1800L x 350D x 650H mm from finished floor level) and Wall Mounted Luggage Rack (1000L x 500D x 300H mm). The complete unit shall be manufactured using Sheesham Veneered Plywood with Solid Sheesham Wood framework, detailing and supports as specified.Study Table: The study table shall be of size 1200L x 500D x 750H mm. The top shall be made using 18 mm thick Sheesham Veneered Plywood. The table framework, aprons and legs shall be made from Solid Sheesham Wood, duly seasoned and chemically treated. The legs shall be 60x60 mm section, tapering slightly towards the bottom. The table shall be provided with 02 drawers, having Solid Sheesham Wood drawer facia with vertical fluted detailing. Drawer boxes shall be made using 18 mm MR Grade Plywood with 350 mm telescopic channels and integrated finger groove pull-out arrangement. The table shall be rigidly assembled using traditional mortise and tenon joinery with concealed screw fixing wherever required.TV Ledge: The wall mounted TV ledge shall be 1800L x 350D x 200H mm, installed at 650 mm height from finished floor level. The length may vary depending upon room layout. The top and bottom panels shall be made using 18 mm thick Sheesham Veneered Plywood with internal framing to achieve the required thickness and rigidity. The outer side supports shall be made in Solid Sheesham Wood. The unit shall be provided with 02 handleless drawers on either side having Solid Sheesham Wood fluted drawer facia and 01 central open compartment for placement of Set Top Box and media equipment. Provision shall be made for concealed cable routing and electrical wiring through the rear panel. The unit shall be securely fixed to the wall using heavy-duty concealed mounting brackets. |
| 99 | Luggage Rack: The wall mounted luggage rack shall be of overall size 1000L x 500D x 300H mm with 250 mm floor clearance. The carcass shall be made using 18 mm thick Sheesham Veneered Plywood. The top shall be finished with 15–18 mm thick natural stone of approved shade and pattern. The front shall be provided with 250 mm high fluted facia incorporating a concealed finger groove pull for the handleless drawer. The drawer box shall be made using 18 mm MR Grade Plywood fitted on telescopic channels of hafele or equivalent approved make. The unit shall be suspended from the wall using concealed heavy-duty fixing brackets.All drawers shall operate on telescopic channels and shall be provided with concealed finger groove pull profiles without exposed handles. All exposed veneered surfaces shall be finished in approved Walnut Brown shade using wood stain, two coats of wood sealer and Satin Finish Melamine polish. All Solid Sheesham Wood members shall receive the same finish for a uniform appearance. Necessary hardware, concealed wall fixing brackets, fasteners, buffers and accessories shall be provided complete.The rate shall include all Sheesham Veneered Plywood, Solid Sheesham Wood, MR Grade Plywood, stone top, fluted detailing, drawer channels, concealed hardware, polishing, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 100 | WARDROBE WITH FRIDGE & TEA COFFEE COMPARTMENT |
| 101 | Providing, fabricating and fixing in position Wardrobe with Fridge Compartment and Tea Coffee Counter of overall size 2000L x 600D x 2000H mm, manufactured using traditional wood working techniques as per approved drawings. The unit shall be fabricated at site as per actual on-site dimensions. The unit shall be constructed using 18 mm thick Sheesham Veneered Plywood for all exposed outer surfaces including sides, top, base, vertical partitions, open shelves and tea counter structure. The back shall be 12 mm thick Sheesham Veneered Plywood. The wardrobe shutters shall be 25 mm thick Sheesham Veneered Plywood. Solid Sheesham Wood, duly seasoned and chemically treated, shall be used only for the base skirting.The unit shall comprise a 1000 mm wide double-door wardrobe and a 1000 mm wide utility section with refrigerator compartment, tea coffee counter and open storage. The wardrobe shall be fitted with 25 mm thick double shutters, an SS hanging rod at the top providing approximately 1200 mm hanging height, and 02 fixed shelves at the bottom made from 18 mm MR Grade Plywood finished with 10 mm solid Sheesham wood lipping, forming two storage compartments of approximately 300 mm height each.The utility section shall include a 650 mm clear internal width refrigerator compartment below the counter. Ventilation shall be provided through 300L x 300H mm wooden louvered grills on the side and back panels. The tea coffee counter shall have a 15–18 mm thick natural stone top of approved shade and a fluted Sheesham Veneered Plywood back panel. Open shelves shall be provided alongside the refrigerator for storage of dustbin and accessories. Provision shall be made for electrical socket points and a recessed LED light above the counter. |
| 102 | The wardrobe shall be fitted with concealed modular SS hinges, 150 mm long stainless steel finish handles, magnetic door catchers, SS hanging rod and all necessary hardware of approved make. All exposed veneered surfaces shall be finished in approved Walnut Brown shade using wood stain, two coats of wood sealer and Satin Finish Melamine polish. Internal surfaces shall be finished with matching veneer and clear protective polish.The rate shall include all Sheesham Veneered Plywood, MR Grade Plywood, Solid Sheesham Wood skirting, stone top, fluted detailing, louvered ventilation panels, hardware, electrical provisions, LED light fitting, polishing, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 103 | SIDE TABLE |
| 104 | Providing, fabricating and Placing Side Table having overall size of 500 Dia × 500H mm, manufactured using Solid Sheesham Wood duly seasoned and chemically treated. The table shall have a 28 mm thick solid Sheesham wood top with rounded edge profile and smooth chamfered underside, supported on a sculptural pedestal base as shown in the approved design.The base shall be fabricated using Solid Sheesham Wood sections of 90 × 40 mm, forming four tapered inclined legs interconnected at the bottom to create a rigid cross-shaped pedestal. The legs shall be securely joined to the underside of the top using concealed joinery, waterproof adhesive and fasteners to ensure structural stability. The base profile shall provide adequate leg clearance while maintaining proper balance and strength.All exposed wood surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Finish Melamine Top Coat. The table shall be provided with nylon buffers at the bottom and all necessary hardware, transportation, installation, labour and incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 105 | STUDY CHAIR |
| 106 | Providing, fabricating and Placing in position Study Chair of overall size 450 mm (L) × 480 mm (D) × 850 mm (H) with seat height of 450 mm, manufactured as per approved design and drawing. The complete exposed framework shall be fabricated from Solid Sheesham Wood, duly seasoned and chemically treated against termites and borers. The chair shall comprise front legs of 45 × 45 mm finished section, rear legs extending into the back support of 45 × 40 mm section, side seat rails of 30 × 60 mm section, front and rear seat rails of 30 × 70 mm section, back support members of 30 × 40 mm section, and side stretchers of 25 × 35 mm section, all rigidly assembled using mortise and tenon joints, waterproof adhesive and concealed fasteners.The seat shall be constructed using 12 mm thick MR Grade Plywood fixed over the solid wood frame and upholstered with 50 mm thick, 32 density PU Foam, giving a total upholstered seat thickness of 60 mm. The backrest shall be fabricated using 12 mm thick MR Grade Plywood upholstered with 25 mm thick, 32 density PU Foam, ergonomically shaped for proper lumbar support. The chair shall be upholstered in Premium Upholstery Fabric of approved shade and texture min. ₹800/- per metre MRP, neatly tailored with concealed stitching and wrinkle-free finish.All exposed wooden surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Melamine Top Coat. The chair shall be provided with nylon bushes to the bottom of legs for floor protection. The item shall include all solid wood, plywood, PU foam, upholstery fabric, polishing, hardware, labour, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 107 | BED DOUBLE |
| 108 | SUITE ROOM BED – KING SIZE - WITH FULLY UPHOLSTERED WINGBACK TUFTED HEADBOARD (WITHOUT STORAGE)Providing, fabricating and placing in position Suite Room Bed King Size having overall dimensions 1910 mm (W) × 2125 mm (L) and designed to accommodate a 72\\" × 78\\" (1830 × 1980 mm) mattress. The headboard height shall be 1200 mm from finished floor level. The bed shall be manufactured using seasoned and chemically treated Solid Sheesham Wood, MR Grade Plywood, high-density PU foam and premium upholstery fabric, complete in all respects as per approved drawings and specifications.The headboard shall be of fully upholstered wingback design with integrated side wings and deep-button tufted detailing on the front face. The overall headboard width shall be aligned exactly with the width of the bed base without any extension beyond the bed frame. The headboard shall be fabricated using 18 mm thick MR Grade Plywood as the primary structural framework material with adequate internal timber reinforcement to prevent deflection and ensure long-term rigidity. The front face shall be upholstered using min. 75 mm thick, 32 density PU Foam and Side Wings shall be upholstered using 25mm thick PU Foam finished with premium quality upholstery fabric @Rs.800 per metre MRP as approved by the Engineer-in-Charge. The bed base shall be constructed with an overall height of 350 mm from floor level with base skirting height 150mm and main frame height 200mm, fabricated using 28 mm thick Solid Sheesham Wood, with the visible frame built up to an overall finished thickness of 40 mm by providing additional solid wood lipping. |
| 109 | The mattress support platform shall consist of 12 mm thick MR Grade Plywood securely fixed over 40 mm × 20 mm Solid Wood battens fastened to the inside of the main frame to provide continuous and uniform support for the mattress.The bed shall feature a recessed plinth/skirting on the front and both side elevations to create a floating cantilever appearance. The recessed skirting shall be 150 mm high, manufactured from 28 mm thick Solid Sheesham Wood, and set back 100 mm from the outer face of the bed frame on all three visible sides.The complete bed structure shall be designed as a knock-down assembly. Assembly shall be achieved using heavy-duty metal corner brackets fixed internally to ensure rigid, vibration-free performance without visible external hardware.The bed shall be without any storage provision, drawers, hydraulic lift-up mechanism or under-bed compartments.The bed shall be suitable to accommodate a 72\\" × 78\\" (1830 × 1980 mm) mattress. The recommended mattress thickness shall be 200 mm (8 inches).All exposed Solid Sheesham Wood surfaces shall be machine sanded smooth, stained in Walnut Brown shade, sealed with two coats of wood sealer, and finished with premium satin melamine polish.Upholstery fabric shall be wrinkle-free, tightly stretched and uniformly finished with accurately aligned deep-button tufting. All workmanship shall be of the highest quality with precision joinery, concealed fasteners, smooth rounded edges and flawless finishing, complete as specified and approved by the Engineer-in-Charge.The cost shall include materials, labour, handling, transportation, installation, etc complete in all respects as per the direction of Engineer In-charge. |
| 110 | BEDSIDE TABLE |
| 111 | Providing, fabricating and Placing Bedside Cabinet of overall size 600L × 400D × 500H mm, comprising 02 drawers as per approved image/drawing.The Bedside Cabinet shall be manufactured using 18 mm thick Sheesham Veneered Plywood for top, sides, bottom and internal carcass members, with 12 mm thick MR Grade Plywood back panel. Drawer boxes shall be made using 18 mm thick MR Grade Plywood for sides and back, with 9 mm thick MR Grade Plywood bottom securely housed in grooves.The cabinet shall be supported on Solid Sheesham Wood tapered legs of 40 × 40 mm section, interconnected with a 40 × 28 mm solid wood base framework. The unit shall provide an approximate 62 mm floor clearance for ease of cleaning. Drawer front facias shall be made in Solid Sheesham Wood, approximately 180 mm high, with plain smooth finish as shown in the approved drawing. Drawers shall operate on heavy-duty telescopic channels of approved make and shall be fitted with black powder-coated metal edge profile handles recessed along the top edge of each drawer front or as approved.All exposed timber surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer, followed by two coats of Melamine Satin Finish. Internal plywood surfaces shall receive matching melamine finish.All exposed edges shall be neatly finished and hardware fixed true to line and level.The rate shall include all materials, labour, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 112 | CONSOLE TABLE |
| 113 | Providing, fabricating and Placing in position Console Table of overall size 900L × 400D × 750H mm, manufactured in contemporary style as per approved image/drawing. The table shall be provided with an 18 mm thick Sheesham Veneered Plywood top finished with Solid Sheesham Wood lipping on all exposed edges. The top shall incorporate a gently curved front profile as shown in the approved design and shall be separated from the supporting legs by a 10 mm shadow groove, creating a floating top appearance.The supporting structure shall comprise Solid Sheesham Wood elegantly profiled legs of 75 × 75 mm section at the top, shaped and tapered as per approved design. The legs shall be interconnected on all four sides with 130 × 18 mm solid Sheesham wood aprons having a matching curved front profile, providing adequate rigidity and structural stability. The complete framework shall be assembled using traditional woodworking techniques with mortise-and-tenon joints, dowels, concealed fasteners and waterproof adhesive to ensure long-term strength and durability.All exposed wooden surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer, followed by two coats of Melamine Satin Finish. Veneered surfaces shall be carefully grain matched, while all exposed edges and corners shall be neatly finished and slightly eased for a refined appearance.The rate shall include all materials, Solid Sheesham wood, Sheesham veneered plywood, adhesives, fasteners, polishing, labour, machining, assembly, transportation, handling, loading, unloading, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 114 | TV PANEL WITH LEDGE |
| 115 | Overall Dimensions: 3940L x 600D x 2100H TV Panel: 2400 L × 200 D × 2100 H mmProviding , fabricating and Placing of TV Panel Cum Room Partition. The TV Panel will have a Built-in Ledge running over the TV Panel and continuing further to be used as a Writing Platform with Mini Fridge compartment accomodated below the platform. Provision shall be made for the TV Screen of rotating type (TV screen size 1200Lx750H approx) so it can be watched on both side of the room. TV Panel with Dual-Side Ledge Cum Room PartitionFabricated using seasoned and chemically treated Solid Sheesham Wood, Sheesham Veneered Plywood, Stone finish laminate on ledge and premium hardware, complete in all respects as per approved drawings and the direction of the Engineer-in-Charge. The contractor shall verify all dimensions at site and prior to commencement of fabrication.The unit shall comprise a TV partition panel, a floating dual-purpose ledge usable from both sides of the partition, and a storage cabinet below the desk portion designed to accommodate a mini refrigerator.The TV partition panel shall measure approximately 2400 mm L × 200 mm D × 2100 mm H and shall be fabricated using a rigid internal framework of 50 × 50 mm Solid Sheesham Wood with all exposed faces finished in 18 mm thick Sheesham Veneered Plywood. The panel shall be structurally fixed to the floor and reinforced internally to safely support the TV and cantilevered ledge. Provision shall be made for concealed electrical conduits, HDMI, LAN, power cables and TV mounting brackets.A recessed opening shall be provided for installation of the television as per approved TV size, with removable access panel for maintenance and concealed cable management behind the TV.A floating ledge shall project continuously through the partition and remain fully usable from both sides. The ledge shall measure approximately 3640 mm L × 200 mm D (TV Legde) / 600 mm D (Writing Ledge) and shall be finished with 1 mm thick stone finish laminate as approved fixed over 18 mm MR Grade Plywood, with edge build-up to achieve an overall visible thickness of approximately 40 mm. |
| 116 | The ledge shall function as a TV console at 550 mm H and as a working desk at 750 mm H from both side. Heavy-duty concealed MS brackets or internal steel reinforcement shall be provided to safely support the cantilever projection without visible supports.Below the desk portion, a mini fridge storage cabinet approximately 600-650 mm wide shall be provided for accommodating a mini refrigerator, with adequate ventilation openings, removable service access panel and provision for electrical socket and cable routing.All exposed timber surfaces shall be manufactured using Solid Sheesham Wood and Sheesham Veneered Plywood, while concealed carcass members shall be fabricated using 18 mm MR Grade Plywood. Exposed edges shall be finished with solid wood lipping and neatly profiled to match the approved design. All shutters shall be fitted with premium quality soft-close hinges, magnetic catchers, approved handles, concealed fasteners and all necessary hardware for complete installation.All exposed timber surfaces shall be machine sanded smooth, stained in Walnut Brown or approved shade, sealed with two coats of wood sealer, and finished with two coats of premium satin melamine polish. The item shall include all timber work, plywood, veneer, laminate, concealed steel reinforcement, cable management provisions, electrical conduits provision , refrigerator space provision , ventilation openings, polishing, hardware, transportation, labour, installation and all incidental works, complete in all respects as approved by the Engineer-in-Charge. |
| 117 | DINING TABLE ROUND |
| 118 | Providing, fabricating and Placing Café Round Dining Table of overall size 900 mm Diameter × 750 mm Height, as per approved design. The table shall have a 30 mm thick stone top as approved of Rs.800 per sqft market value, comprising 15 mm thick stone (Italian Marble/Engineered Stone/Quartz) with 15 mm built up edge moulding, machine polished on all exposed surfaces and edges. The supporting structure shall be manufactured from Solid Sheesham Wood, duly seasoned and chemically treated. The table shall have a tapered conical pedestal of Ø180 mm at the bottom reducing to Ø140 mm at the top, securely fixed to the top with concealed steel plate of thickness 6 mm and dia 300mm. The base shall consist of a 450 mm diameter solid Sheesham wood platform of 45 mm overall thickness with moulded profile, designed to provide adequate stability for commercial use. All timber members shall be accurately machined with concealed joinery and waterproof adhesive. Exposed wooden surfaces shall be finished in approved Walnut Brown shade using wood stain, two coats of sealer and Satin Finish Melamine polish. Nylon floor protectors and other necessary hardware to be provided. The cost is including material, labour, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge |
| 119 | SOFA 3 SEATER |
| 120 | Providing, fabricating and Placing in position Sofa 3 Seater of overall size 2100L x 850D x 700H mm with 430 mm seating height and 700 mm seating depth, as per approved drawing. The sofa shall have an exposed Solid Sheesham Wood base framework of 40x28 mm section and legs of 60x60 mm tapering to 40x40 mm, duly seasoned and chemically treated. The sofa shall have 90 mm floor clearance. All exposed wooden members shall be finished in approved Walnut Brown shade using wood stain, two coats of wood sealer and Satin Finish Melamine polish.The seat shall have an overall thickness of 150 mm, comprising 120 mm thick PU Foam of 32 density fixed over a 30 mm thick solid Sheesham wood seat frame of 60x30 mm section. The seat support shall consist of elastic webbing and zig-zag springs fixed on the wooden seat frame, complete with jute hessian cloth, cotton marking cloth, SR adhesive and necessary upholstery materials to provide durable and comfortable seating. The upholstered frame below the seat shall be 150 mm high.The armrests shall be 150 mm thick and 270 mm high above the seat. The armrest and backrest structure shall be manufactured using 9 mm MR Grade Plywood reinforced with solid Sheesham wood members as required. The armrests shall be upholstered with 50 mm thick PU Foam of 32 density. The sofa shall be provided with loose back cushions of 150 mm thickness, filled with high-quality polyfill fibre for enhanced comfort and support.The sofa shall be upholstered in premium upholstery fabric or PU Leatherette of approved make and shade, with material value minimum Rs.800 per metre (MRP) included in the cost. Stitching shall be neat and uniform with concealed fixing wherever required. Nylon buffers shall be provided under the legs.The rate shall include all materials, solid Sheesham wood, MR Grade plywood, PU foam, fibre filling, upholstery fabric, upholstery accessories, hardware, polishing, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 121 | ROOM CHAIR |
| 122 | Providing, fabricating and Placing Room Chair of overall size 700 mm (L) × 750 mm (D) × 750 mm (H) with seat height of 450 mm, manufactured as per approved design and drawing. The complete exposed framework shall be fabricated from Solid Sheesham Wood, duly seasoned and chemically treated against termites and borers. The chair shall comprise front legs of 50 × 50 mm finished section, rear legs extending into the back frame of 50 × 40 mm section, armrests of 35 × 60 mm section, side seat rails of 30 × 75 mm section, front and rear seat rails of 30 × 90 mm section, and intermediate support members of 30 × 50 mm section, all rigidly assembled using mortise and tenon joints, waterproof adhesive and concealed fasteners.The upholstered seat shall be supported on a separate Solid Sheesham Wood frame of 65 × 28 mm section, fitted with heavy-duty Elastic Webbing and Zig-Zag Springs to provide proper resilience and long service life. The upholstery shall include Jute Hessian Cloth, Cotton Marking Cloth, SR Adhesive, nails and all necessary upholstery accessories. The seat shall be provided with 120 mm thick, 32 density PU Foam, giving a total seat cushion thickness of 150 mm after upholstery. The loose back cushion shall be filled with high-quality Polyfill Fibre and upholstered separately for enhanced comfort.The chair shall be upholstered in Premium Upholstery Fabric of approved shade and texture min. ₹800/- per metre MRP, neatly stitched with concealed seams and removable cushion covers wherever approved. All exposed wooden surfaces shall be finished in Walnut Brown shade using approved wood stain, followed by two coats of wood sealer and Satin Melamine Top Coat. The chair shall be provided with nylon bushes to the bottom of legs for floor protection. The item shall include all solid wood, upholstery materials, polishing, hardware, labour, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer In-Charge. |
| 123 | WARDROBE WITH LUGGAGE RACK |
| 124 | Providing, fabricating and Placing in position Wardrobe Unit with Luggage Rack of overall size 1750L x 600D x 2000H mm, manufactured using traditional wood working techniques as per approved drawings. The unit shall be fabricated at site as per actual on-site dimensions. The unit shall be constructed using 18 mm thick Sheesham Veneered Plywood for all exposed outer surfaces including sides, top, base, vertical partitions, open luggage compartment and wardrobe carcass. The back shall be 12 mm thick Sheesham Veneered Plywood and the wardrobe shutters shall be 25 mm thick Sheesham Veneered Plywood. Solid Sheesham Wood, duly seasoned and chemically treated, shall be used only for the base skirting.The unit shall comprise a 1000 mm wide double-door wardrobe and a 1000 mm wide open luggage and dressing compartment. The wardrobe shall be fitted with 25 mm thick double shutters, an SS hanging rod at the top providing approximately 1200 mm clear hanging height, and 02 fixed shelves at the bottom made using 18 mm MR Grade Plywood finished with 10 mm solid Sheesham wood lipping, forming two storage compartments of approximately 300 mm height each.The open compartment shall be provided with a 15–18 mm thick natural stone top fixed at approximately 750 mm height to serve as a luggage platform. The back panel shall have vertical fluted detailing in Sheesham Veneered Plywood. A solid Sheesham wood slatted luggage rack shall be provided below the stone top with slats of approximately 40x20 mm section at equal spacing. The back panel shall be fitted with 04 solid Sheesham wood coat hooks and provision shall be made for a recessed LED downlight in the top panel.The wardrobe shall be fitted with concealed modular SS hinges, 150 mm long stainless steel finish handles, magnetic door catchers, SS hanging rod and all necessary hardware of approved make. All exposed veneered surfaces and solid wood members shall be finished in approved Walnut Brown shade using wood stain, two coats of wood sealer and Satin Finish Melamine polish. Internal surfaces shall be finished with matching veneer and protective clear polish.The rate shall include all Sheesham Veneered Plywood, MR Grade Plywood, Solid Sheesham Wood, stone top, fluted back panel, slatted luggage rack, coat hooks, LED light provision, hardware, polishing, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 125 | BATHROOM VANITY CABINET |
| 126 | Providing, fabricating and Fixing in place Wall Mounted Vanity Cabinet of approximate overall size 1000L × 600D × 550H mm, manufactured as per approved drawing and site requirements. The overall dimensions shall be verified at site before fabrication and may vary to suit the actual bathroom layout, basin position and plumbing services. The cabinet shall be manufactured using 18 mm thick BWP (Boiling Waterproof) Grade Plywood for top, bottom, sides, internal partitions, drawer fronts, shelving and 18 mm thick laminated back panel. All external visible surfaces shall be finished with 1.0 mm thick laminate of approved shade and texture, while all internal surfaces shall be finished with 0.8 mm thick laminate. Exposed edges shall be sealed with matching edge banding, neatly machine finished.The unit shall comprise 02 equal-sized storage drawers positioned on the left and right sides, operating on heavy-duty telescopic drawer channels of approved make. A fixed false centre drawer facia shall be provided to conceal the bottle trap and plumbing connections below the wash basin while maintaining a symmetrical appearance. Drawers shall be provided with integrated finger groove handle opening formed within the drawer facia, eliminating the need for external hardware.The lower portion of the cabinet shall incorporate a open storage shelf , suitable for towels and bathroom accessories, with adequate clear height as per approved drawing. The cabinet shall be designed for wall-mounted installation using heavy-duty concealed mounting brackets and suitable anchor fasteners capable of safely supporting the cabinet, countertop and basin loads.All laminate finishes shall be free from bubbles, waves and visible joints. The complete unit shall be accurately fabricated with concealed fixings, waterproof adhesives and precision joinery to ensure rigidity, moisture resistance and long service life. The rate shall include BWP plywood, laminates, edge banding, telescopic drawer channels, finger groove detailing, all cut-outs for plumbing fixtures, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 127 | LIBRARY TABLE |
| 128 | Providing, fabricating and Placing Library Table of overall size 1800 L × 600 D × 750 H mm, manufactured in contemporary design as per approved drawings. The table top shall be made from 25 mm thick Solid Oak Wood, duly seasoned and chemically treated, finished with PU sealer followed by premium clear PU top coat in approved Natural Oak finish. All edges shall be machine-finished with slightly rounded profiles and smooth polished surfaces.The supporting framework shall be fabricated from MS rectangular hollow sections, comprising side leg frames of approximately 50 × 25 mm sections interconnected with longitudinal support members of 50 × 25 mm and 25 × 25 mm sections. All MS members shall be welded, ground smooth and finished with Black Matte Powder Coating of approved shade. The solid oak table top shall be securely fixed to the MS framework using concealed screws and suitable heavy-duty fixing brackets.The table shall be provided with 03 Nos. recessed pop-up box units flush mounted on the table top. Each pop-up box shall have a flip-top aluminium cover and shall be fitted with 02 Nos. 6A universal power sockets, 01 USB Type-A charging port, 01 USB Type-C charging port, 01 RJ45 data port and 01 HDMI pass-through port, complete with wiring access opening and cable exit arrangement.A powder-coated MS cable management tray shall be fixed below the table top between the side frames for routing and supporting electrical and data cables. The tray shall be fabricated from approximately 1.2 mm thick MS sheet with folded edges for rigidity and shall be provided with adequate openings for cable entry, ventilation and maintenance access.The rate shall include Solid Oak wood top, MS framework, powder coating, PU finishing, electrical pop-up boxes with power, USB, Type-C, data and HDMI ports, cable management tray, fixing hardware, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 129 | MEETING TABLE |
| 130 | Providing, fabricating and Placing Conference Table of overall size 4800 L × 1200 D × 750 H mm, manufactured in contemporary design as per approved drawings. The table top shall be made from 25 mm thick Solid Oak Wood, duly seasoned, finished with PU sealer followed by premium clear PU top coat in approved Natural Oak finish. The top edges shall have a sleek rounded profile with smooth radiused corners and machine-finished edges to provide a refined appearance and user comfort.The supporting structure shall comprise MS rectangular hollow section side leg frames of approximately 50 × 25 mm sections interconnected with longitudinal members of 50 × 25 mm and 25 × 25 mm sections. The centre support panel shall be fabricated using 18 mm Oak Veneered Plywood with 40x20mm Oak wood framing on both ends finished in PU Black stained Matte finish on both sides to match the MS framework. All MS members shall be welded, ground smooth and finished with Black Matte Powder Coating. The solid oak table top shall be securely fixed to the MS framework using concealed screws and heavy-duty fixing brackets.The table shall be provided with a continuous central cable management arrangement comprising 06 Nos. recessed pop up Box modules equally spaced along the centre line. Each module shall be fitted with a flip-top aluminium cover and provided with 02 Nos. 6A universal power sockets, 01 USB Type-A charging port, 01 USB Type-C charging port, 01 RJ45 data port and 01 HDMI pass-through port, complete with cable access opening and wiring provision.A powder-coated MS cable management tray shall be fixed below the centre of the table for routing and supporting electrical and data cables. The tray shall be fabricated from 1.2 mm thick MS sheet with folded edges and suitable openings for cable entry, ventilation and maintenance.The rate shall include Solid Oak wood top, Natural Oak Veneered Plywood, PU finishing, MS framework, centre support panel, powder coating, pop up Box modules, power and data accessories, cable management tray, fixing hardware, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 131 | MEETING CHAIR MID BACK |
| 132 | Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be made of metal insert pipe frame padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ in seat and (19+12)mm thick having density 23kg/m³ in back. The same shall be upholstered with leatherite tapestry 1mm thick and 571 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support as well as head support. The chair shall be supplied with chrome plated arm having black integral polyurethane top. For seating durability the chair shall have knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti-shock feature which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with class-3 gas-lift to suit them using the lever under the seat. The Pedestal should have five legged MS CRCA chrome plated having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors which shall be made of injection moulded in black 30% glass filled nylon, confirming to industry standards tested to perform 98,000 cycles with 250lbs load. The seat size shall be 480±10 mm(D) X 475±10 mm(W) and back size shall be 465±10 mm(W) X 510±10 mm(H) from seat. Overall height shall be = 980±10 mm, overall depth = 620±10 mm & overall width = 570±10 mm. |
| 133 | BOOKRACK |
| 134 | Providing, fabricating and Fixing in position Full Height Library Book Rack of overall size 4000L × 400D × 3048H mm, manufactured entirely in Solid Oak Wood and Oak Veneered Plywood. The unit shall be fabricated at site as per actual on-site dimensions. The book rack shall comprise a solid wood outer framework with housed vertical and horizontal partitions forming open storage compartments. The extreme left and right columns shall each be 600 mm wide, while the remaining columns shall each be 400 mm wide. The top two rows and bottom two rows shall each be 400 mm high, with all intermediate rows 300 mm high, complete with a 100 mm high solid Sheesham wood skirting. All joints shall be traditional mortise-and-tenon/dowel construction with waterproof adhesive for rigid and durable construction. All exposed surfaces shall be finished in choice of approved stain with two sealer coats and premium PU Matt finish. The rate shall include all solid Oakwood, oak veneere, joinery, polishing, fixing hardware, labour, transportation, installation and all incidental works, complete as per approved drawings and the directions of the Engineer-in-Charge. |
| 135 | JOURNAL RACK |
| 136 | Providing, fabricating and Placing in position Journal Rack of overall size 900L × 300D × 1800H mm, manufactured in contemporary style as per approved drawing. The Journal Rack shall be made entirely from Solid Oak Wood and Oak Veneered Plywood , using traditional mortise and tenon joinery, to ensure structural rigidity and long service life.The rack shall comprise solid wood side panels of approximately 18 mm thickness interconnected with 18 mm thick top, bottom and intermediate shelves. It shall incorporate five inclined display shelves of approximately 180 mm depth, each provided with a 40 × 20 mm solid wood front retaining lip to securely hold journals, magazines and brochures in a forward display position. The open display compartments of approximately 300 mm clear height shall be provided. The rear of the rack shall be enclosed with 12 mm thick Oak Veneered Plywood back panels, providing rigidity and a premium finished appearance. All exposed edges shall be neatly rounded and sanded smooth.Provision shall be made for a concealed warm white LED strip light recessed below the top panel to illuminate the upper display compartment, All exposed timber surfaces shall be finished in approved shade with one coat of wood filler, two coats of sanding sealer and two coats of PU Finish. The rate shall include all Solid Oak wood, LED light provision with aluminium profile, hardware, adhesives, fasteners, labour, polishing, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 137 | CARD TABLE |
| 138 | Providing, fabricating and Placing Card Table of overall size 900 mm Diameter × 750 mm Height, as per approved image. The table shall be constructed entirely from Seasoned and Chemically Treated Solid Sheesham Wood , using traditional woodworking techniques to ensure strength, stability and long service life.The table top shall be approximately 40 mm thick, comprising a solid Sheesham wood framework with a recessed high-quality felt playing surface of approved colour at the centre. The outer playing ring shall incorporate integral recessed accessory trays equally spaced around the perimeter for holding playing chips, cards. The pedestal shall comprise a 150 × 150 mm solid Sheesham wood central column supported on four solid wood inclined braces of approximately 90 × 45 mm section, securely joined to a cross-shaped base frame of approximately 100 × 75 mm section. The complete base assembly shall be designed to provide maximum rigidity and wobble-free performance during regular use.All exposed wooden surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer, followed by two coats of Melamine Satin Finish. The felt playing surface shall be neatly stretched, wrinkle-free and securely bonded. The rate shall include all materials, labour, assembly, transportation, handling, loading, unloading, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 139 | CARD ROOM CHAIR |
| 140 | Providing, fabricating and Placing Upholstered Arm Chair of overall size 650L × 650D × 850H mm, with approx. 550L × 550D mm clear seating area and 450 mm seating height, manufactured in contemporary style as per approved drawings. The chair shall be made using Solid Sheesham Wood, duly seasoned and chemically treated. The exposed timber frame shall comprise 50×50 mm front and rear legs tapering to 40×40 mm at the bottom, interconnected with a 50×30 mm solid Sheesham wood seat frame. The armrests shall be formed with 40×40 mm solid Sheesham wood sections, extending continuously into a gently curved solid wood back rail of approximately 120 mm height.The seat shall be supported on a 50×30 mm solid Sheesham wood frame and upholstered with 75 mm thick, 32 density PU foam, giving an overall seat thickness of approximately 130 mm. The inner backrest and side panels shall be ergonomically shaped and upholstered with 50 mm thick, 32 density PU foam over a solid Sheesham wood framework to provide comfortable lumbar and arm support. The chair shall be upholstered in premium quality fabric of approved shade and pattern having an approximate MRP of Rs. 800 per metre.All exposed wooden surfaces shall be finished in Walnut Brown shade with two coats of wood sealer followed by two coats of Satin Melamine finish. The rate shall include all materials, labour, polishing, handling, transportation, installation, and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 141 | THEATRE RECLINER CHAIR |
| 142 | Providing, fabricating and Installing at site Motorized Theatre Recliner Chair of koko model of recliners india brand or equivalent make as approved and given design with approximate overall size 900W × 950D × 1050H mm in upright position and 1650 mm overall depth in fully reclined position, with seat height 460 mm, seat width 550 mm and arm height 620 mm, complete with motorized reclining mechanism, cup holders and premium upholstery, as per approved drawing and specifications.The chair shall be manufactured using a heavy-duty internal framework comprising seasoned Solid Wood members and MR Grade Plywood of suitable thickness for seat, backrest, armrests and structural components. The frame shall be reinforced with steel brackets and mechanical fasteners to provide a rigid, wobble-free construction suitable for heavy commercial use.The seat shall be constructed using 32 Density high-resilience PU Foam over elastic webbing and No-Sag (zig-zag) springs to provide superior seating comfort and durability. The backrest shall be manufactured using 32 Density PU Foam with polyester fibre padding for enhanced softness and ergonomic lumbar support. Armrests shall be similarly padded using PU Foam and fibre.The recliner shall be upholstered in approved PU Leatherette of commercial grade, stitched with heavy-duty matching thread and finished with concealed seams. Upholstery shall be wrinkle-free, removable only where required for servicing, and resistant to abrasion, peeling and normal commercial wear.The chair shall be provided with a motorized reclining mechanism operated through an integrated side-mounted control switch, enabling smooth and silent adjustment of the backrest and extendable footrest. The mechanism shall include overload protection, concealed electric motor, steel linkage assembly and approved power adaptor complete with wiring.Each armrest shall be provided with integrated stainless steel cup holders, flush-mounted within the arm pads. The chair shall be designed with enclosed upholstered side panels concealing all mechanical components for a clean appearance and user safety. |
| 143 | All exposed timber components, wherever visible, shall be smoothly finished, while concealed wooden members shall receive protective sealer coating. All hardware shall be zinc-plated or powder-coated to resist corrosion.The rate shall include Solid Wood framework, MR Grade Plywood, PU Foam, fibre padding, PU Leatherette upholstery, motorized reclining mechanism, electrical components, stainless steel cup holders, springs, webbing, all hardware, labour, transportation, handling, installation, testing and commissioning and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 144 | BUNK BED |
| 145 | Providing, fabricating and Placing MS Bunk Bed suitable for 02 persons, having overall size approximately 2000L × 1000D × 2000H mm, designed to accommodate 02 mattresses, each of size 914 × 1905 mm (36\\" × 75\\"), with 100 mm thick mattress recommended. The bunk bed shall be manufactured using MS hollow sections duly welded, ground smooth and finished in Black Matte Powder Coating. The primary structural frame, vertical posts and side rails shall be made using 50×38×2 mm MS tube, while intermediate members, mattress support frame and guard rails shall be made using 50×25×2 mm and 25×25×2 mm MS hollow sections as required for structural stability. Mattress support shall consist of closely spaced MS slats of size 50x25 suitable for heavy-duty commercial use.The overall height between the top surface of the lower mattress and the underside of the upper mattress shall be approximately 1100 mm, providing comfortable headroom. The upper safety guard rail shall be approximately 300 mm high above the mattress level on the exposed side. Access to the upper bunk shall be provided through an integrated welded MS ladder spaced at approximately 300 mm centres. Floor clearance below the lower bed shall be approximately 150 mm for ease of cleaning.Decorative head and foot panel inserts shall be provided in Solid Sheesham Wood, duly seasoned and chemically treated, finished in Walnut Brown shade with two coats of wood sealer followed by two coats of Satin Melamine finish. All exposed MS members shall have smooth rounded edges, concealed welds and a uniform powder-coated finish.The rate shall include all materials, labour, handling, transportation, installation and all incidental works complete in all respects as per approved drawings and the directions of the Engineer-in-Charge.Note : Mattress cost not included in the cost of the Bunk Bed. |
| 146 | SERVICE TROLLEY |
| 147 | Providing, fabricating and Placing Service Trolley of overall size 750L × 450D × 900H mm, manufactured in contemporary style as per approved drawing. The trolley shall be fabricated entirely from Grade 304 Stainless Steel with PVD Gold finish, comprising four vertical posts of approximately Ø38 mm, interconnected with horizontal members and integrated push handle to form a rigid welded frame. The trolley shall be provided with three tray levels, each having an overall size of approximately 600L × 400D mm, fitted with 15–18 mm thick natural stone/engineered stone inserts of approved shade and pattern. Each tray shall be enclosed with raised stainless steel guard rails of approximately 50 mm height to prevent articles from slipping during movement. Overall spacing between trays shall be approximately 260–280 mm for convenient storage and service.The trolley shall be mounted on 100 mm diameter heavy-duty 360° swivel castors, with two castors provided with locking brakes, ensuring smooth mobility and stability. All stainless steel joints shall be TIG welded, ground and polished smooth with concealed fixing details and rounded exposed edges. The PVD Gold finish shall be uniform, corrosion-resistant and suitable for heavy commercial hospitality use.The rate shall include stainless steel framework, stone tray inserts, PVD coating, castors, all hardware, fabrication, welding, polishing, transportation, handling, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 148 | MASSAGE TABLE |
| 149 | Providing, fabricating and Placing in position Wooden Massage Table of overall size 915W × 2140L × 700H mm, designed to accommodate a 915 × 2140 mm (36\\" × 84\\") mattress with an integrated cut out shall form part of the overall length of the Massage Table with a breathing hole provided in Centre for comfortable massage therapy.The table shall be manufactured entirely from Solid White Ash Wood, duly seasoned , using traditional mortise-and-tenon joinery with waterproof adhesive for a rigid and durable construction. The top frame shall be made using 90×30 mm solid White Ash Wood sections supported on 75×75 mm solid wood legs interconnected with 60×30 mm longitudinal and cross stretchers. A slatted lower storage shelf shall be provided using 60×20 mm solid White Ash Wood slats fixed over a 60×30 mm supporting frame. Decorative curved corner brackets shall be provided below the top frame for additional strength and aesthetics.The table shall be supplied with a 130 mm (5 inch) thick Bonded Foam mattress, giving an overall height of 830 mm from finished floor level. The mattress shall be upholstered using 32 density PU foam covered with premium PU Leatherette of approved shade and quality having an approximate MRP of Rs. 800 per metre. All exposed wooden surfaces shall be finished in an approved shade with two coats of wood sealer followed by two coats of PU finish, providing a smooth, durable and moisture-resistant surface. The rate shall include all materials, labour, handling, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 150 | MASSAGE ROOM TROLLEY |
| 151 | Providing, fabricating and Placing in position Massage Room Service Trolley of overall size 800L × 500D × 800H mm, manufactured entirely from Solid White Ash Wood , duly seasoned . The trolley shall comprise a 60×30 mm solid White Ash Wood framework with 60×60 mm solid wood legs, supporting 03 storage levels. The top tray shall be provided with 90 mm high raised side rails made from 20 mm thick solid wood, suitable for safely holding massage oils, towels and accessories. The middle and bottom shelves shall be constructed using 18 mm thick White Ash Veneered Plywood panels supported on the main solid wood White Ash Wood framework, providing adequate storage for towels, spa accessories and consumables. The overall clear spacing between shelves shall be approximately 250 mm.The trolley shall be mounted on 04 heavy-duty 75 mm diameter swivel castors with 360° rotation, made of non-marking rubber with smooth rolling action, of which 02 castors shall be provided with locking brakes for stability during use.All exposed wooden surfaces shall be finished in approved wood shade with two coats of wood sealer followed by two coats of PU finish. The rate shall include all materials, castors, hardware, polishing, labour, handling, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 152 | GYM BENCH |
| 153 | Providing, fabricating and Placing in position Gym Bench of overall size 1500L × 450D × 450H mm, manufactured in contemporary style as per approved drawings. The seating surface shall comprise 04 nos. Solid White Ash Wood slats, each of size 75 mm wide × 38 mm thick, duly seasoned, fixed with uniform spacing over the supporting frame using concealed stainless steel fasteners. The slats shall have smooth rounded edges and be designed to provide a comfortable, durable and well-ventilated seating surface.The supporting frame shall be fabricated from 40×40×2 mm MS hollow sections, welded to form a rigid rectangular base with intermediate cross members for additional strength. All welds shall be ground smooth and the complete MS structure shall be cleaned, treated and finished with Black Matte Powder Coating of approved quality for corrosion resistance and long service life. The bench shall be provided with heavy-duty nylon floor protectors at all contact points to prevent damage to finished flooring.All exposed wooden surfaces shall be finished in approved wood shade with two coats of wood sealer followed by two coats of PU finish. The rate shall include all materials, MS fabrication, powder coating, polishing, hardware, labour, handling, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 154 | LOCKERS |
| 155 | Providing, fabricating and Placing Locker Cabinet of overall size 1200L × 400D × 2000H mm, comprising 18 individual lockable compartments arranged in 3 columns × 6 rows, manufactured as per approved drawings. The cabinet shall be constructed using 18 mm thick OakVeneered Plywood for shutters, side panels, top, base and internal partitions, with 12 mm thick MR Grade Plywood back panel. All exposed edges shall be finished with Solid Oak Wood lipping of approved thickness, neatly rounded and polished.Each locker compartment shall be provided with an individual full-overlay shutter fitted with heavy-duty concealed hinges, cam lock with two keys, magnetic catcher and all necessary hardware. Locker numbering plates shall be fixed on each shutter as approved. Internal compartments shall be of equal size with smooth finished interiors suitable for secure storage of personal belongings.All exposed wooden surfaces shall be finished in approved shade with two coats of wood sealer followed by two coats of PU finish, while internal surfaces shall receive matching protective clear finish. The cabinet shall be assembled using traditional woodworking joinery with screws, dowels and adhesive to ensure rigidity, durability and long service life.The rate shall include all Oak veneered plywood, MR Grade plywood, Solid Oak wood lipping, locks with keys, concealed hinges, hardware, polishing, labour, handling, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 156 | Providing, fabricating and Placing Wellness Area Rack of overall size 700L × 400D × 900H mm, manufactured in contemporary open-shelf design using Solid Oak Wood throughout and traditional woodworking techniques. The rack shall comprise four solid Oak wood corner posts of approximately 50 × 50 mm, interconnected with 40 × 30 mm solid oak wood rails to form a rigid framework. It shall be provided with three slatted shelves made from 20 mm thick × 45 mm wide solid Oak wood slats with uniform spacing for ventilation and drainage, suitable for storing towels, toiletries and wellness accessories. The top shelf shall incorporate raised side and back rails of approximately 70 mm height to prevent articles from slipping, while the intermediate and bottom shelves shall be equally spaced to provide convenient storage.All timber shall be thoroughly seasoned and chemically treated against termites and borers. All exposed edges shall be neatly rounded, joints shall be mortise-and-tenon/dowel construction with waterproof adhesive, and the complete unit shall be sanded smooth. The exposed wooden surfaces shall be finished in approved shade with two coats of wood sealer followed by two coats of PU finish for a durable, moisture-resistant surface. Nylon floor protectors shall be provided below the legs.The rate shall include all Solid Oak wood, joinery, hardware, polishing, labour, handling, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 157 | WALL RACK |
| 158 | Providing, fabricating and Fixing Wellness Area Wall Rack of overall size 1200L × 400D × 900H mm, manufactured in contemporary style using Solid Oak wood throughout with traditional woodworking techniques. The unit shall comprise a double-door storage cabinet on one side and three open display shelves on the other. The cabinet shutters shall be provided with solid wood louvered panels for ventilation, mounted on heavy-duty concealed hinges with knobs and magnetic catchers. The open shelving shall be formed using 18 mm thick solid wood shelves equally spaced for storage of towels, toiletries and wellness accessories.The lower portion shall incorporate an open storage shelf of approximately 200 mm height with a 32 mm diameter solid wood towel hanging rod fixed below. All exposed edges shall be neatly rounded, shelves securely housed within the frame, and the complete unit designed for heavy-duty wall mounting using concealed brackets and fasteners.All exposed wooden surfaces shall be finished in approved shade with two coats of wood sealer followed by two coats of PU clear finish, providing a smooth, durable and moisture-resistant surface suitable for wellness and spa environments.The rate shall include all Solid Oak wood, concealed wall fixing hardware, hinges, magnetic catchers, polishing, labour, handling, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 159 | WALL RACK |
| 160 | Providing, fabricating and Fixing Wellness Area Wall Mount Rack of overall size 750L × 350D × 1200H mm, manufactured in contemporary style using Solid Oak Wood throughout with traditional woodworking techniques. The unit shall be wall-mounted and divided into four continuous horizontal open storage sections, each of approximately 270 mm clear height, suitable for storing towels, spa accessories and wellness products. The rack shall be fabricated with 18 mm thick solid wood horizontal shelves and carcuss body, made using traditional mortise-and-tenon/dowel joinery with waterproof adhesive. Side panels and intermediate vertical supports shall be proportionately spaced to ensure adequate structural strength and prevent shelf deflection over the full length.All timber shall be thoroughly seasoned and chemically treated , All exposed edges shall be neatly rounded and machine sanded smooth. The rack shall be designed for heavy-duty concealed wall fixing using MS brackets, anchor fasteners and necessary fixing hardware to ensure rigidity and safety under service loads.All exposed wooden surfaces shall be finished in approved shade with two coats of wood sealer followed by two coats of clear PU finish, providing a smooth, durable and moisture-resistant surface suitable for wellness and spa environments.The rate shall include all Solid Oak wood, concealed wall fixing brackets and hardware, adhesives, polishing, labour, handling, transportation, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 161 | PUFFY |
| 162 | Fabricating and placing of Puffy having overall size of 450Lx450Dx450H mm upholstered using good quality upholstery fabric of Min. Rs.800 per metre MRP as approved. The puffy inner structure shall be made using 18mm MR grade plywood. The polished round legs shall be made using solid Sheesham wood of size 50x50mm turned down to 35x35mm at base. The seating shall be made using good quality 75mm thick PU foam of 32 density and 12mm PU foam shall be wrapped on the borders. The foamwork shall be covered with upholstery fabric material. The wood work shall be duly finished using wood stains, wood sealers and Melamine polish as top coat in Walnut Shade as approved. Complete as per approval and direction of Engineer Incharge. |
| 163 | BENCH |
| 164 | Fabricating and placing of Bench of size 1500Lx450Dx450H mm made using solid Oak wood. The seat of the bench shall have wooden slats each measuring around 60mmx28mm with even gap of around 10mm. The slatted seat frame shall be 60mm in height. The legs are 60x60mm connected with supporting frames of size 40x28 mm. The Bench shall be duly finished using wood stains, wood sealers and Melamine polish as top coat in Walnut Shade as approved. Complete as per approval and direction of Engineer Incharge. |
| 165 | SALON CHAIR |
| 166 | Providing, fabricating and Placing Hydraulic Salon Hair Cutting Chair of approximate overall size 700L × 700D × 950–1100H mm, with adjustable seating height from 500 mm to 650 mm through a heavy-duty hydraulic lifting mechanism, manufactured in contemporary style as per approved drawing. The chair shall comprise a fully upholstered seat, backrest and armrests mounted on a heavy-duty chrome-plated hydraulic swivel base suitable for professional salon use.The chair seat shall have an approximate 550W × 500D mm seating area with 100 mm thick, 40 density high resilience moulded PU foam over a hardwood and plywood frame. The backrest shall measure approximately 550W × 450H mm above the seat and be upholstered with 50 mm thick, 32 density PU foam to provide proper lumbar support. Fully upholstered armrests of approximately 100 mm width shall be integrated with the chair frame to provide comfortable support during salon operations.The internal chair structure shall be fabricated using seasoned hardwood framework, flexible plywood, MR Grade plywood, and high-quality webbing, securely assembled with concealed fasteners to ensure durability under continuous commercial use. The chair shall be upholstered in premium White PU Leatherette of approved make and quality, min. MRP Rs. 800 per metre, resistant to moisture, salon chemicals, hair colour stains and routine cleaning. All stitching shall be double-stitched with neatly finished seams.The chair shall be mounted on a heavy-duty hydraulic pump with 360° swivel mechanism, capable of smooth height adjustment and continuous rotation with locking facility. The hydraulic mechanism shall be enclosed within a polished stainless steel/chrome-plated steel column and mounted on a heavy circular steel base of approximately 600 mm diameter, fitted with anti-slip rubber protection to ensure stability during use. A side-mounted foot-operated hydraulic lever shall be provided for effortless height adjustment.All exposed metallic components including the hydraulic column, operating mechanism and base shall be finished in mirror polished chrome or stainless steel finish, resistant to corrosion and salon chemicals. The chair shall be designed to safely support a minimum working load of 150 kg. The rate shall include hydraulic lifting mechanism, 360° swivel assembly, chrome-plated circular base, upholstered seat, backrest and armrests, premium White PU leatherette, high resilience PU foam, hardwood framework, all hardware, transportation, handling, installation, testing and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 167 | SALON HAIR WASH CHAIR |
| 168 | Providing, fabricating and Placing Salon Hair Wash Chair with Shampoo Station of approximate overall size 700L × 1250D × 1000H mm, manufactured in contemporary style as per approved drawing. The chair shall comprise a fully upholstered fixed seat integrated with a rear-mounted ceramic shampoo basin, suitable for professional salon use. The overall seat height shall be approximately 480 mm, with an overall arm height of approximately 680 mm.The chair shall have an approximate 550W × 500D mm seating area upholstered with 100 mm thick, 40 density high resilience moulded PU foam over a seasoned hardwood and MR Grade plywood frame. The ergonomically inclined backrest shall measure approximately 550W × 700H mm, upholstered with 75 mm thick, 32 density PU foam to provide proper lumbar support during hair washing. Fully upholstered armrests of approximately 90–100 mm width shall be integrated with the chair frame. The chair shall be upholstered in premium White PU Leatherette of approved make and quality, min. MRP Rs. 800 per metre, resistant to water, salon chemicals, hair colour stains and routine cleaning. All stitching shall be double stitched with neatly finished seams.The internal chair structure shall be manufactured using seasoned hardwood framework, flexible plywood, MR Grade plywood, heavy-duty elastic webbing and high resilience polyurethane foam, securely assembled with concealed fasteners to withstand continuous commercial usage. The chair shall have a rigid enclosed base construction with concealed levelling feet for stability and floor protection.Ceramic Shampoo Basin:The chair shall be complete with a heavy-duty glazed ceramic shampoo basin of approximate size 600W × 520D × 260H mm, mounted securely behind the chair at an ergonomic height. The basin shall be provided with a soft black moulded neck cushion, chrome-plated single lever mixer tap, hot and cold water inlet, pull-out hand shower with flexible hose, waste coupling with removable hair strainer, drain assembly and all standard plumbing accessories. The ceramic surface shall be stain resistant, chemical resistant and easy to clean. Necessary concealed provisions shall be made for water supply and waste outlet connections. |
| 169 | All exposed metallic fittings including the mixer, shower hose, drain fittings and fixing hardware shall be finished in chrome-plated brass or stainless steel of approved make. The complete assembly shall be designed for smooth operation, durability and ease of maintenance under commercial salon conditions.The rate shall include upholstered salon chair, ceramic shampoo basin, neck cushion, mixer tap, hand shower, waste fittings, plumbing accessories, hardwood framework, PU foam, premium White PU leatherette, all hardware, transportation, handling, installation, testing and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 170 | SALON PEDICURE CHAIR |
| 171 | Providing, fabricating and Placing Salon Pedicure Spa Chair Set comprising Pedicure Chair, Ceramic Foot Spa Basin, Wooden Platform, Mobile Technician Stool and Side Storage Unit, manufactured in contemporary style as per approved drawing. The complete unit shall be suitable for professional salon use and shall have an approximate overall footprint of 1800L × 1200D × 1400H mm.Pedicure ChairThe Pedicure Chair shall be of approximate size 850W × 900D × 1400H mm, with a seating height of approximately 500 mm. The chair shall comprise a high backrest with integrated padded headrest, upholstered armrests with solid wood arm caps incorporating cup holders, and a generously cushioned seat for extended user comfort.The internal structure shall be manufactured using seasoned hardwood, flexible plywood and MR Grade plywood, reinforced with heavy-duty elastic webbing. The seat shall be upholstered with 100 mm thick, 40 density High Resilience PU Foam, while the backrest and headrest shall be upholstered with 75 mm thick, 32 density PU Foam. The chair shall be upholstered in premium White PU Leatherette of approved quality, min. MRP Rs. 800 per metre, resistant to moisture, salon chemicals, massage oils and routine cleaning. All stitching shall be double stitched with neatly finished seams.The chair shall be provided with a manually adjustable reclining backrest and fixed armrests with polished solid Sheesham wood arm caps having integrated cup holders. The enclosed base shall be rigidly constructed with concealed levelling feet.Ceramic Pedicure BasinThe set shall include a heavy-duty glazed ceramic pedicure spa basin of approximate size 550 mm Dia. × 350 mm depth, mounted on the wooden platform in front of the chair. The basin shall be complete with cushioned neck/foot support, hot and cold water inlet, waste outlet, drain fitting, overflow arrangement and all standard plumbing accessories. The ceramic surface shall be stain resistant, chemical resistant and easy to clean. |
| 172 | Wooden PlatformThe chair and basin shall be mounted on a raised engineered wooden platform of approximate size 1800L × 1200D × 150H mm, manufactured using 18 mm BWP Grade Plywood finished with approved laminate/veneer. The platform shall provide integrated concealed plumbing access and cable management provisions. Recessed warm white LED strip lighting with aluminium profile and diffuser shall be provided along the platform skirting to create ambient illumination.Mobile Technician Stool (Pouffe)The set shall include one round mobile technician stool of approximate size 400 mm Dia. × 420 mm height, comprising a hardwood and plywood frame upholstered with 75 mm thick, 32 density PU Foam and premium White PU Leatherette matching the chair. The stool shall be mounted on a five-wheel heavy-duty swivel castor base for smooth mobility during pedicure operations.Side Storage UnitOne round side storage cabinet of approximate size 450 mm Dia. × 650 mm height shall be provided adjacent to the chair. The unit shall be manufactured using 18 mm BWP Grade Plywood finished with approved laminate/veneer and shall comprise internal storage with hinged shutter for salon consumables. The top shall be finished with Solid Sheesham Wood and polished in approved Walnut Brown Melamine Finish.All exposed timber surfaces shall receive one coat of wood filler, two coats of sanding sealer and two coats of Melamine Satin Finish in approved Walnut Brown shade. All exposed metal components shall be powder coated or chrome finished as applicable. Electrical wiring, LED lighting, plumbing provisions and hardware shall be concealed wherever possible.The rate shall include Pedicure Chair, Ceramic Basin, Wooden Platform, Mobile Technician Stool, Side Storage Unit, premium White PU Leatherette, PU foam, hardwood framework, plywood, plumbing fittings, LED lighting, electrical accessories, hardware, transportation, handling, installation, testing and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 173 | RECPTION COUNTER |
| 174 | Providing, fabricating and Placing Reception Counter of overall size 2400L × 750D × 1050H mm, manufactured in contemporary style as per approved image/drawing. The counter shall be constructed using 18 mm thick Sheesham Veneered Plywood for all visible top, sides, front, modesty panel and structural members. All exposed edges shall be finished with Solid Sheesham Wood lipping.The counter shall comprise a 750 mm high receptionist worktop with an integrated 350 mm wide visitor transaction counter positioned at 1050 mm finished height. The raised visitor counter shall return on both side panels, forming a continuous wrap-around feature as shown in the approved design. The reception worktop shall provide adequate clear knee space and working area for computer, keyboard and office accessories. The front elevation shall feature a centrally positioned vertical fluted panel manufactured from Solid Sheesham Wood, framed with plain veneered side panels to match the approved design. Concealed warm white LED strip lighting shall be provided below the visitor counter overhang, complete with concealed wiring, LED driver and accessories.The receptionist side shall be provided with 02 integrated pedestal drawer units, one at each end, each of overall size 450L × 450D × 700H mm, comprising 03 drawers operating on heavy-duty telescopic channels. Drawer boxes shall be manufactured using 18 mm MR Grade Plywood with 9 mm thick plywood bottoms. Adequate cable management provision shall be incorporated within the worktop for computer and electrical wiring. All exposed wooden surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer, followed by two coats of Melamine Satin Finish. Internal surfaces shall receive matching melamine finish. The complete unit shall be manufactured using traditional woodworking techniques with concealed joinery, using waterproof adhesives to ensure rigidity, dimensional stability and long service life. The rate shall include all Sheesham veneered plywood, Solid Sheesham wood lipping and fluted members, MR Grade plywood, telescopic drawer channels, LED strip lighting with driver, cable management provisions, adhesives, fasteners, polishing, labour, machining, assembly, transportation, handling, loading, unloading, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 175 | STORAGE ALMIRAH |
| 176 | Providing, making and placing of Storage Almirah having overall outer size of 900Lx450Dx1800H mm made using solid Sheesham wood duly seasoned and chemically treated and One sided (OS) Sheesham veneered plywood. The Almirah shall having 2 solid shutters made in 18mm sheesham veneered plywood with a support framework of size 40x30 mm at back on all sides of each shutter. The outer framework section of the almirah shall be made in solid sheesham wood of size 40x30mm on front, sides and back. The side panel of the almirah shall be made in 12mm Sheesham veneered plywood . The back panel shall be made in 12mm MR grade plywood. The almirah shall have a Top, 3 Shelves and a base made in 18mm MR grade plywood with sheesham wood lipping of size 18mmx10mm on all 4 sides of the shelves. The almirah shall be duly fitted with hardware such as 02nos. handles of size 250mm, good quality door lock, magnet catcher, door latch 150mm, 06 nos SS heavy duty hinges 100mm. The almirah shall be duly finished using wood stains, wood sealers and Melamine polish in Walnut Shade as approved. Complete as per approval and direction of Engineer Incharge. |
| 177 | CORNER WALL RACK |
| 178 | Providing, fabricating and Fixing Corner Wall Mount Rack of overall size 300 L × 300 D × 900 H mm, manufactured entirely from 18 mm thick Solid Oak Wood, duly seasoned and chemically treated, as per approved drawings. The unit shall be designed for installation at an internal wall corner and shall comprise four equally spaced triangular corner shelves integrated with two full-height side panels and a full-height rear corner backing, forming a rigid wall-mounted storage unit.The side panels shall measure approximately 900 mm high × 120 mm wide, while each triangular shelf shall project approximately 300 mm on both adjoining walls with radiused front corners. Shelves shall be spaced at approximately 220–230 mm clear vertical intervals and shall be fixed using housed joints, concealed dowels and adhesive, ensuring adequate strength without visible fasteners.The complete unit shall be fabricated using traditional mortise & tenon, housed joints and dowel joinery wherever applicable. All exposed edges shall be smoothly rounded and machine sanded.The rack shall be provided with a heavy-duty concealed wall mounting system comprising recessed MS hanging plates/brackets, stainless steel screws, anchor fasteners and all accessories required for secure installation on masonry/RCC walls.All exposed and internal timber surfaces shall be finished in the approved shade with one coat wood filler, two coats sanding sealer and two coats clear PU finish.The rate shall include Solid Oak Wood, concealed fixing hardware, adhesives, polishing, labour, transportation, handling, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 179 | SOFA 2 SEATER (WELLNESS AREA) |
| 180 | Providing, fabricating and Placing in position 2-Seater Sofa of overall size 1300L × 700D × 850H mm, with seat height 430 mm, manufactured using Solid Sheesham Wood and upholstered using premium upholstery fabric as approved, of approx Rs.800 per metre MRP.The exposed structural frame shall be manufactured from seasoned and chemically treated Solid Sheesham Wood using traditional mortise and tenon joinery. The frame shall comprise 85 × 28 mm front seat rail, 85 × 28 mm side rails, 50 × 28 mm arm rails. The sofa shall be supported on Solid Sheesham Wood front legs of ready section 50 × 40 mm and rear legs of ready section 40 × 40 mm, shaped and inclined as per approved design to achieve the desired profile, with approximately 220 mm floor clearance.The seating shall comprise 02 fixed seat cushions of size 600Lx550D, constructed using 120 mm thick PU Foam of 32 Density fixed over 12 mm thick plywood base, upholstered in approved fabric of not less than Rs. 800 MRP with concealed zipper openings.The backrest shall comprise 02 fixed back cushions of size 600Lx400H, manufactured using 50 mm thick PU Foam of 32 Density fixed over 12 mm thick plywood backing, upholstered in matching approved fabric and supported on the inclined solid wood back frame.All exposed timber surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer and two coats of Melamine Satin Finish. The rate shall include all materials, labour, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 181 | STAFF TABLE with Loose Mobile Pedestal |
| 182 | Providing, fabricating and Placing Staff Table of overall size 1200 L × 600 D × 750 H mm, comprising an Oak Veneered Plywood worktop supported on a powder-coated MS tubular frame, complete with Loose Mobile Pedestal Unit, as per approved drawings. The table top shall be manufactured from 18 mm thick Natural Oak Veneered Plywood with Oak wood lipping on all exposed surfaces. The complete top shall receive PU sealer followed by Clear PU finish in approved shade. The underside of the tabletop shall be finished with veneer face and PU finish. The supporting structure shall be fabricated from 50 × 50 × 1.6 mm MS square tube legs interconnected with 50 × 25 × 1.6 mm MS rectangular tube perimeter frame below the tabletop. The complete MS framework shall be welded, ground smooth and finished in Black or White Matte Epoxy Polyester Powder Coating as approved. Adjustable nylon levelling bushes shall be provided at the bottom of each leg. The table shall be provided with one 80 mm diameter cable grommet complete with matching cover for cable management.Loose Mobile Pedestal Storage CabinetProviding, fabricating and Placing Loose Mobile Pedestal Storage Cabinet of overall size 450 L × 450 D × 700 H mm, comprising 03 drawers, manufactured using 18 mm thick Oak veneered Plywood. All exposed outer surfaces including cabinet carcass, drawer facias and top shall be finished with Natural Oak Veneer and PU sealer followed by Clear PU finish in approved shade.All internal surfaces, drawer sides, drawer backs shall be manufactured from 18 mm MR Grade Plywood with veneer face, finished to match the external finish. The back panel shall be 12 mm thick MR Grade Plywood. Drawer bottoms shall be 9 mm thick plywood housed in grooves. Drawers shall operate on telescopic drawer channels and shall be fitted with approved metal handles and locking arrangement with two keys. The pedestal shall be mounted on 50 mm diameter heavy-duty nylon swivel castors, including two lockable castors for stability. All exposed edges shall be neatly finished with matching solid wood lipping or veneer edging as applicable. The complete wooden unit shall receive PU sealer and Clear PU finish, while all metal components shall be finished in Black or White Matte Powder Coating as approved. The rate shall include all Oak veneered plywood, MR Grade plywood, PU finishing, MS framework, powder coating, hardware, castors, cable grommet, labour, transportation, handling, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 183 | CONSOLE TABLE |
| 184 | Providing, fabricating and Placing Console Table of overall size 1500L × 380D × 900H mm, manufactured in classical style as per approved drawing. The Console Table shall be made entirely from Solid Sheesham Wood, duly seasoned and chemically treated, using traditional mortise and tenon joinery, dowel joints and concealed fasteners to ensure structural rigidity and long service life.The table shall be provided with a 28 mm thick solid Sheesham wood top having elegantly rounded corners and a moulded edge profile on all exposed sides. The top shall be supported on a 170 mm deep solid wood apron/frame with decorative stepped mouldings and profiled edges running continuously on all four sides, matching the approved design.The table shall be supported on six turned Solid Sheesham Wood legs, comprising four corner legs and two centrally positioned intermediate legs for additional stability. Each leg shall be approximately 75 × 75 mm at the top, intricately turned on a wood lathe with classical ring mouldings and tapering gracefully to approximately 35 mm diameter near the bottom. The legs shall be securely housed into the solid wood apron using traditional mortise and tenon joints, ensuring rigidity without visible mechanical fixings.The complete framework shall be fabricated entirely in solid timber with concealed corner blocking and internal reinforcement to prevent twisting, warping and movement over time. All exposed edges shall be smoothly rounded, hand-finished and free from visible defects. The overall design shall reflect a premium handcrafted appearance with uniform grain matching and seamless joinery.All exposed timber surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer and two coats of Melamine Satin Finish. The finish shall be smooth, uniform and resistant to normal wear and cleaning.The rate shall include all Solid Sheesham Wood, seasoned timber, traditional joinery, adhesives, fasteners, complete polishing, labour, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 185 | CONSOLE TABLE (Suite Room) |
| 186 | Providing, fabricating and Placing Console Table of overall size 1500L × 380D × 900H mm, manufactured entirely from Solid Sheesham Wood, duly seasoned and chemically treated, as per approved drawing. The table shall be handcrafted using traditional mortise and tenon joinery, dowel joints and concealed mechanical fasteners to ensure maximum structural strength, dimensional stability and long service life. The table shall be provided with a 28 mm thick solid Sheesham wood top having elegantly curved front profile with radiused ends and moulded edge detailing on all exposed sides. The top shall be formed from edge-glued solid timber boards with matched grain pattern and finished free from visible joints, cracks or defects. The supporting apron shall be fabricated from 180 mm deep Solid Sheesham Wood members, shaped to match the flowing curved front profile of the table and provided with decorative mouldings along the top and bottom edges. The apron shall be securely joined to the legs using traditional mortise and tenon construction with concealed reinforcement blocks for enhanced rigidity. The table shall be supported on four carved Solid Sheesham Wood cabriole legs of approximately 75 × 75 mm section at the top, gracefully tapering and curving to approximately 40 × 40 mm near the floor. Each leg shall incorporate smooth handcrafted profiles with rounded transitions and decorative foot detailing as shown in the approved design. Legs shall be firmly housed into the apron frame without visible fixings. The complete structure shall be manufactured entirely from Solid Sheesham Wood . All exposed edges shall be rounded, hand-sanded and finished smooth. The completed table shall be rigid, level and free from distortion, wobbling or visible defects. All exposed timber surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer and two coats of Melamine Satin Finish, producing a smooth, uniform and durable surface resistant to normal wear and cleaning. The rate shall include all Solid Sheesham Wood, seasoning and chemical treatment, traditional woodworking, adhesives, fasteners, complete polishing, labour, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 187 | ACCENT TABLE |
| 188 | Providing, fabricating and Placing Accent Table of overall size 600 mm Dia. × 750H mm, manufactured entirely from Solid Sheesham Wood, duly seasoned and chemically treated, as per approved image.The table shall be provided with a 600 mm diameter top manufactured from 18 mm thick Solid Sheesham Wood, finished with rounded edge profile. The top shall be supported on a circular Solid Sheesham Wood apron frame of 65 × 28 mm section, securely joined using traditional mortise and tenon joinery.The table shall be supported on four gracefully curved Solid Sheesham Wood legs of finished section size 65 × 65 mm at the maximum point, tapering towards the floor as per approved design. The legs shall be interconnected with 28 × 28 mm Solid Sheesham Wood stretchers arranged in a cross formation to improve rigidity and stability. The table shall provide an approximate 150 mm floor clearance.All exposed timber surfaces shall be finished in approved Walnut Brown shade with one coat of wood filler, two coats of sanding sealer and two coats of Melamine Satin Finish, producing a smooth, durable and uniform surface.The rate shall include all materials, labour, transportation, handling, installation at site and incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 189 | All timber shall be free from knots, cracks, warping and other defects. All exposed timber surfaces shall be machine sanded smooth, stained in Walnut Brown or approved shade, sealed with two coats of wood sealer, and finished with two coats of premium Satin Melamine polish. Upholstery shall be neatly stitched with concealed fixings and wrinkle-free finish.The rate shall include all Solid Sheesham Wood, upholstery, PU foam, safety belt, hardware, adhesives, polishing, labour, transportation, loading, unloading, installation and all incidental works, complete in all respects as per approved drawings and the directions of the Engineer-in-Charge. |
| 190 | Double Bed Mattress |
| 191 | Double Bed Spring Mattress with Water Resistant Cotton Mattress Protector :MATTRESS SIZE : 72” x 78” x 8” (W X L X H). The Spring Mattress shall feature a medium-firm feel, 8-inch thickness and a 10-year manufacturer warranty. It shall utilize a 3-zone pocket spring architecture designed for orthopedic support and complete spinal alignment.Core Technologies & LayersTriple-Zone Pocket Springs: Separates support into distinct areas for the head/shoulders, spine/hips, and legs to relieve pressure points.Impressions Foam Quilting: Adapts to body contours independently of ambient temperature for contour-hugging comfort.Acuprofile & Resitec Foam: Enhances air circulation, even weight distribution, and supportive bounce.Foam Wall Technology: Reinforces mattress edges and corners to prevent sagging and improve side seating.Neem Fresche Fabric: Built-in anti-microbial treatment protecting against dust mites and allergies as per approved shade and quality. Mattress Protector Specifications - Whie Coloured, Cotton & polyurethane material Top Layered & side lined, with Pull on Closure type, must have Elastic spandex providing a snug fit around the mattress, should be Machine washable.Make Sleepwell /Kurlon or equivalent complete as per directions and approval of EIC. |
| 192 | Single Bed Mattress |
| 193 | Providing and placing in position Single Bed Mattress of size 36” x 75” x 5” (W X L X H) with Water Resistant Cotton Mattress Protector. The mattress must have 4 inches thick bonded foam with 1 inch HR Foam cushioning on top covered with premium jacquard / knitted mattress upholstery fabric as per approved shade and quality. Make Sleepwell /Kurlon or equivalent complete as per directions and approval of EIC. Mattress Protector Specifications - Whie Coloured, Cotton & polyurethane material Top Layered & side lined, with Pull on Closure type, must have Elastic spandex providing a snug fit around the mattress, should be Machine washable. |
| 194 | Bed Sheet with pillow cover |
| 195 | Providing and placing in position White Bed Sheet 2740*2740 mm with pillow cover a pillow of size 450*700 mm made of fabric 100% Long Staple Combed Cotton, Percale Weave, 400 Thread Count, 160 GSM, Mercerized and Sanforized, Commercial laundry compatible, White colour, of approved colour and design of wellspun, trident, raymond, portico complete as per approval of EIC. |
| 196 | Pillow |
| 197 | Providing and placing in position premium hospitality grade sleeping Pillows of size 450*700 mm of 300 TC 100% cotton down proof Fabric with filling 1000 gms virgin siliconised hollow conjugated polyster fibre having medium firm density, double stiched, piped edges of white colour of wellspun, trident, raymond, portico or as per approval of EIC. |
| 198 | Bed Cover |
| 199 | Providing and placing in position premium hospitality grade Bed Cover of Size - Double bed - 229 x 274 CMs. of premium jacquard polyster/ cotton blend 450 GSM quilted premium stiched borders of approved colour and design of wellspun, trident, raymond, portico complete as per approval of EIC. |
| 200 | Cushions set of Two pc. per Set With cover. |
| 201 | Providing and placing premium hospitality grade Cushions Set of size 400*400 mm of 300 TC 100% cotton Fabric with filling 500-600 gms siliconised fibre having medium firm density, double stiched of white colour of wellspun, trident, raymond, portico or as per approval of EIC.Cushion Cover of premium jacquard/ velvet/ linen blend 300 GSM, double stiched with hidden zipper of approved colour of wellspun, trident, raymond, portico or as per approval of EIC. |
| 202 | Carpet |
| 203 | Providing and placing in position premium hospitality grade Carpet made up of 100% solution dyed nylon type 6,6 having pile weight 1500 gms/sqm and total carpet weight of 2600 gms/ sqm, 10 mm thick, anti-slip, anti-static, anti-fungal, soil resistant, stain resistant, faint resistant of approved, shade and design as per approval of EIC. |
| 204 | Hand Towel |
| 205 | Providing and placing in position premium hospitality grade Hand Towel of size 400*600 mm of 100% Combed cotton, double stiched hems, high water absorbent hand towel white in colur of 650 and above GSM of wellspun, trident, raymond, portico as per approval of EIC. |
| 206 | Bath Towel |
| 207 | Providing and placing in position premium hospitality grade Bath Towel of size 750*1500 mm of 100% Combed cotton, double stiched hems, high water absorbent bath towel white in colur of 650 and above GSM of wellspun, trident, raymond, portico as per approval of EIC. |
| 208 | Blanket |
| 209 | Providing and placing in position premium hospitality grade Blanket of size 220 cm x 240 cm of 500 TC Mink Polyester Blanket, Minimum Wieght 5 Kg, Double ply construction, anti- piling, anti- static of wellspun, trident, raymond, portico of approved colour as per approval of EIC. |
| 210 | Entrance Door Mat |
| 211 | Providing and placing in position premium commercial-grade doormat with anti-slip backing for guest room entrances, complete in all respects.100% Solution-Dyed Nylon having Pile Height: 10 mm, Total Thickness: 12 mm, Pile Weight: 1000 GSM, Total Weight: 3000–3200 GSM of 3M Nomad, Milliken, Forbo, Notrax, Kleen-Tex, Dunlop or Equivalent brand as approved by EIC. |
| 212 | Room Door Mat |
| 213 | Providing and placing in position premium 100% premium microfiber polyester doormat, Minimum 1200 GSM pile weight, 20 mm pile height, TPR anti-slip backing, Commercial laundry compatible (minimum 100 wash cycles), Anti-fungal and anti-bacterial treatment, complete in all respects of 3M Nomad, Milliken, Forbo, Notrax, Kleen-Tex, Dunlop or Equivalent brand as approved by EIC. |
| 214 | Hanger |
| 215 | Providing and placing in position Standard adult wooden hangers made up of Premium hardwoods such as lotus wood, maple, beech, or pine, paired with galvanized or chrome-plated 360° steel swivel hooks of size 45 cm (18 inches) wide, thickness of 1.2 cm, and stand 24 cm high with trouser bar of hardwood with anti-slip PVC sleeve. They shall support a weight capacity of up to 12 kg. |
| 216 | Runner |
| 217 | Providing and placing in position premium decorative bed runner for double beds of size 2000*600 mm and 5 mm thick complete in all respects, suitable for luxury hospitality use of D’Decor, Portico, Raymond Home, Welspun Hospitality or equivalent as approved by EICThe Fabric shall be 100% Polyester Jacquard or Polyester-Cotton Blend (70:30) of 450 GSM, Soft-touch finish, Wrinkle resistant, Anti-pillingThe Interlining shall be of High-quality polyester felt of Weight 120 GSM uniformly padded for better drape.The Backing Fabric : Anti-slip polyester backingOf D’Decor, Portico, Raymond Home, Welspun Hospitality or equivalent as approved by EIC |
| 218 | Duvet Cover |
| 219 | Providing and placing in position premium hospitality grade Duvet Cover of King size: 114 x 96 inches of 100% Cotton fabric, Percale or Sateen weave Minimum 300 TC, 140 GSM, White or Off-white, Concealed zipper, Minimum 4 corner ties to secure the duvet/comforter, Washing Grade 4–5, Double-needle stitching, Reinforced corners, Machine washable, Minimum 100 industrial wash cyclesDuvet Insert Outer Fabric shall be 100% Cotton, 300 TC with Filling of Virgin hollow conjugated siliconized polyester fibre, Non-allergenic and odour-free, Filling Weight: 300 GSM, Box quilting (10–12 inch box), Even distribution of filling, No lump formation, Corner Loops for attachment to duvet cover of White or approved Colour, Machine washable, Fibre should not clump after repeated washing, Double stitched with piping on all edges, Free from stains, holes and weaving defects, Soft finish with breathable fabric, No loose threads, Uniform stitching and quilting, Hypoallergenic material. |
| 220 | Rollor Blinds |
| 221 | Providing and fixing Rollor Blinds of good quality and approved make made out of Fade resistant Imported fabric/ Sunscreen Fabric including Roller Mechanism and lock with Stainless steel spring mechanism, chain system for smooth and silent operation with all necessary hooks,Extruded aluminium weighted bottom rail, Powder-coated steel brackets, Zinc-coated hardware, Heavy-duty concealed fixing system, etc. complete as per direction and sample approved by engineer-in-charge. Vista, Hunter Douglas, or equivalent. |
| 222 | Fabric curtains with sheer curtains |
| 223 | Providing and fixing Fabric curtains with sheer curtainsMain Fabric: Cotton, linen with heavy blackout weave; 350–400 GSM; provides privacy and light regulation of min. Rs 800/- per mtr.Sheer Curtain: Voile, chiffon, or lightweight polyester; 100 GSM; filters 30–35% of natural light of min. Rs 400/- per mtr.Hem Weight: Built-in lead weight string or weighted bottom hem for vertical fluid draping on sheers .Fullness Ratio: 2.5x the width of the window track for standard pinch pleats or wave folds.Channel System Type: Double-channel or dual-track profile width profile of 60mm to 75mm across the top face, ceiling/wall-mounted system (inner track for sheers, outer track for main fabric) made up of Extruded architectural aluminum with powder-coated of approved finish and Gliders / Runners shall be Silent nano-rollers spaced every 8–10 cm for friction-free movement.(Area of opening to be measured for payment purpose) |
| 224 | Glass Partition |
| 225 | Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as pr IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS-316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make. Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates. fastener, anchors, SS channel laminated glass etc. all complete.Providing and foding fully glass door with patch fitting door. Door shall consists of 12mm thick PLAIN toughened float glass (saint Globin) fixing with necesary designer film, approved locking system, ss screws, gasket & heavy duty floor springs and 25mm dia ss full length door handles pair as selected as per architectural detailed drawings and specifications and as directed by E.I.C. The work will include required scaffolding upto all height, via chicken mess etc completeFor the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured |
| 226 | Movable Wooden Partition |
| 227 | Providing, Fabricating and placing in position premium handcrafted solid wood folding partition/screen with decorative carved Jaali panels complete with hinges, hardware, finishing and all accessories complete as per design and approval of EIC. Material : kiln-seasoned Solid sheesham (Indian Rosewood) having Timber moisture content: 8–12% and Free from knots, cracks, sapwood and insect attack.Dimensions : Height: 1800–2100 mm, Width of each panel: 450–500 mm, Number of panels: 4 panel, Overall opened width of 4 Panel: 1800–2000 mm, Thickness: Outer frame: 35–40 mm and Carved infill: 18–22 mm.Solid wood section Frame : Vertical members: 50 × 40 mm, Horizontal members: 50 × 35 mm, Mortise and tenon joints with waterproof adhesive, No visible screws on exposed faces.Decorative Panels : Solid carved wooden Jaali, Minimum carving thickness: 18 mm, Smooth edges without splinters, Symmetrical carving pattern, CNC precision carving or hand carving.Hinges : Heavy-duty SS 304 butt hinges, Minimum 3 hinges per joint, 270° opening, Satin finish.Finish: PU Matt Finish (20–30 Gloss), Three coats sealer, Two coats PU, Anti-scratch coating, UV-resistant finish, Water-resistant Hardware : SS304 screws, Brass inserts where required, Nylon floor protectors, Adjustable levelling pads.All corners rounded (R2–R3) |
| 228 | SS Dustbin 35Ltrs. |
| 229 | Stainless steel (SS) dustbins rust-resistant grade 304 steel, capacities 35 liters with swing lid mechanisms.Sheet Thickness: 1.0 mm heavy-duty for outdoor useFinish: Matt/ mirror-polished/ brushed silver as per approval of EIC. |
| 230 | SS Dustbin 10Ltrs. |
| 231 | Stainless steel (SS) dustbins rust-resistant grade 304 steel, capacities 10 liters with swing lid mechanisms.Sheet Thickness: 1.0 mm heavy-duty for outdoor useFinish: Matt/ mirror-polished/ brushed silver as per approval of EIC. |
| 232 | Building Signage |
| 233 | Providing and fixing of Brass letters on front façade upto Iind floor level at CSOI, HCM RIPA by Brass Sheet of 22 guage and upto 2' Height letters in Hindi/English language with powder coating i/c nut bolt, washer, fastner and adhesive, etc. with all scaffolding and tools, plants, etc. complete as per directions of Engineer- Incharge.Measurement shall be made in per inch of letter's height of individual letter. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender