Tender For Comprehensive Maintenance In Pcda Office Building Sec-09 Under Ge Chandigarh.
Tender Value
48 Lakhs
Estimated cost
Bid Submission
31 Aug 2026
6 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Comprehensive Maintenance In Pcda Office Building Sec-09 Under Ge Chandigarh.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 19-Aug-2026 | DATE CORRIGENDUM | Date | 31-Aug-2026 |
| 2 | 19-Aug-2026 | BOQ CORRIGENDUM | BOQ | 31-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 2 | Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas, chimney in kitchen and similar suspended work complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 4 | Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 5 | Dismantling timber scantlings any position n fillets, rails, posts, rafters, purlins, gate etc. under 40 sq. cm in section complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 6 | Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for, complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 7 | Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 8 | Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 9 | Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 10 | Taking down chowkhats with shutters (without taking off shutter from frame) n exc 1.5 Sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 11 | Taking down chowkhats with shutters (without taking off shutter from frame)exc 1.5 Sqm but n exc 4 sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 12 | Taking down steel window/ventilator with shutters (without taking off shutter from frame) not exc 1.5 Sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) B1 complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 13 | Taking down steel or window/ventilator with shutters (without taking off shutter from frame) exc 1.5 Sqm but not exc 4 sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) B1 complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 14 | Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 15 | Taking down and refxing of shutter in same opening of any description size but exc 1 sqm and n.exc 2 complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 16 | Taking down existing old gate and Erection and re-fixing only, Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 17 | Taking down and refixing in position alphabetical letters in Hindi, English and punjabi made of stainless steel sheet of grade SS-304L of thickness 1.25 mm and fixing to MS Sheet claddig with necessary fixing arrangements, any size of each letter height, width and depth as per font complete including disposal of unservicable rubbish off the premises complete all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 18 | Petty repair to existing steel window by welding hinges or removing the steel window shutters from the frame and re-fixing after welding making serviceable all as specified. |
| 19 | Petty repair to existing steel door /steel mumty door by welding hinges or removing the steel door shutters from the frame and re-fixing after ,welding making serviceable all as specified. |
| 20 | Dismantling Stone slabs and tiles/paver block of any description or thickness in floors, aprons etc, complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 21 | Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 100/ 75/ 50 mm jointed in cement mortar and taking out of trenches and wall, if required complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. |
| 22 | Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 23 | Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 24 | Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc using acetic acid and citric acid used for descaling and removing mineral deposite from tank (capacity exc 2000 but n exc 5000 ltr), complete all as specified and as directed |
| 25 | Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.Note:- Debris will be disposed as per UT norms and Contractor will laise with UT athority for the same and rates quoted shall be deemed to include this aspect. |
| 26 | Supplying and fixing in repairs Ball valves for 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed by Engineer-in-Charge. |
| 27 | Plain cement concrete (1:7:12) type F-2,using 40 mm graded stone aggregate as in sunken floor etc complete all as specified and directed by Engineer-in-Charge. |
| 28 | Providing, cement concrete PCC 1:2:4 type B-1 (using 20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs stone, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engineer-in-Charge. |
| 29 | 25 mm thick Plain cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in flooring including finishing the cement concrete surface even and smooth with using extra cement complete all as specified and directed. |
| 30 | Plain cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base to paver blocks etc complete all as specified and directed by Engineer-in-Charge. |
| 31 | Plain cement concrete type C2, 1:3:6 (using 20 mm graded stone aggregate) as in sub base of flooring/ hard standing/ pavings /plinth protections, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 32 | Providing Reinforced cement concrete (1:2:4), type B-1, (using 12.50 mm graded crushed stone aggregates),as in lintel beam,roof beam,lintel bands,chajjas,counter slab any hight of bldg etc and the like complete all as specified. |
| 33 | TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. |
| 34 | Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves inncluding supports, overhangs, etc. also splays between floors and beams, etc. (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge. |
| 35 | First quality Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardener, resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 36 | Glazed Ceramic tiles conforming to IS 15622 of size 600x300mm and 7 mm thickness of approved make, shade and design, laid over a base rendering of average 15mm thick cement mortar 1:4. Tiles shall be fixed using high-preformance polmer-modified tile adhesive conforming to IS 15477 type 1 (or type 2 if using large-format/vitrified-body glazed tiles) applied uniformly using a notched trowel, ensuring complete back-battering to achieve maximum coverage and prevent hollow voids. tiles shall be laid with a uniform 3mm joint width maintained accurately using PVC spacers. Joints shall be thoroughly cleaned of any oozong adhesive, dust or contaminants, and filled flush with heavy- duty, stain-free, water-resistant three-component epoxy grout of matching shade. rate shall include all surface preparation (including hacking or cleaning of the base concrete) mixing, application, curing, strict cleaning of tile surfaces to completely remove epozy residue, tools, tackles, scaffolding, equipment, materials and labour complete all as specified and directed by Engineer-in-Charge. |
| 37 | Glazed Ceramic tiles conforming to IS 15622 of size 450x300mm and 7 mm thickness of approved make, shade and design, laid over a base rendering of average 15mm thick cement mortar 1:4. Tiles shall be fixed using high-preformance polmer-modified tile adhesive conforming to IS 15477 type 1 (or type 2 if using large-format/vitrified-body glazed tiles) applied uniformly using a notched trowel, ensuring complete back-battering to achieve maximum coverage and prevent hollow voids. tiles shall be laid with a uniform 3mm joint width maintained accurately using PVC spacers. Joints shall be thoroughly cleaned of any oozong adhesive, dust or contaminants, and filled flush with heavy- duty, stain-free, water-resistant three-component epoxy grout of matching shade. rate shall include all surface preparation (including hacking or cleaning of the base concrete) mixing, application, curing, strict cleaning of tile surfaces to completely remove epozy residue, tools, tackles, scaffolding, equipment, materials and labour complete all as specified and directed by Engineer-in-Charge. |
| 38 | Vitrified ceramic tiles coloured Light shade (scratch and stain resistant tiles) 8 to 9 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors,skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 15mm thick screed bedding layer in CM (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 39 | Vitrified ceramic tiles coloured Light shade (scratch and stain resistant tiles) 8 to 9 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors,skirting etc set and jointed with epoxy cement slurry over and including 15mm thick screed bedding layer in CM (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 40 | Vitrified ceramic tiles coloured Light shade (scratch and stain resistant tiles) 8 to 9 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 10mm thick screed bedding layer in CM (1:4) and pointed with epoxy coloured cement to match with surface of tiles (upto 6th floor) complete all as specified and directed by Engineer-in-Charge. |
| 41 | Vitrified ceramic tiles coloured Light shade (scratch and stain resistant tiles) 8 to 9 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 1.0 Sqm, in floors,skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 15mm thick screed bedding layer in CM (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 42 | Vitrified ceramic tiles coloured Light shade (scratch and stain resistant tiles) 8 to 9 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 1.0 Sqm, in skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 10 mm thick screed bedding layer in CM (1:4) and pointed with epoxy coloured cement to match with surface of tiles (upto 6th floor) complete all as specified and directed by Engineer-in-Charge. |
| 43 | Machine pressed factorymade chequered tiles of required size, shape & colour 22 to 25mm thick with grey cement and pigment, over and including 15 mm thick screed in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors complete, all as specified and as directed by Engineer-in-Charge. |
| 44 | Out door/parking tiles heavy duty for light traffic Non skid,anti scratch,heavy grip ,vitreous/semi vitreous coloured ,unique designs tiles 8 to 10 mm thick area of each tile of size 300 mm x 300 mm, in floors parking/outdoortiles etc. set and jointed setting & jointed with 4 mm spacer and grouting the joint with epoxy grout mix of organic coated filler of desired shade , hardener,resin in the ratio of 8:1:2 over & including 15mm thick bedding of cement sand mortar (1:6) and pointed with appoxy coloured cement to match with surface of tiles complete all as specified and as directed. |
| 45 | Machine cut Kota stone slab flooring 16-18 mm thick,SIZE 55 CM x 55 cm laid over & including 15 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge. |
| 46 | Machine cut Kota stone slab 16-18 mm thick as in skirting, dado and pillars etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge. |
| 47 | Green Marble work 16 to 18 mm thick (table rubbed and Pre polished) in steps (Treads/Riser/Skirting), jambs, pillars, window cills, cooking platforms and like over 15mm thick screed bed/back coat in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including Bull nose Rounding to edges of stone slabs, such as in steps, cooking platform, and other similar works complete all as specified |
| 48 | Granite jet black shade,18- 20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 20 mm thick (average thickness) cement mortar (1:4) screed and jointed with grey cement mixed with matching shade pigment including rounding of/moulding to edge (half round ) as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge. |
| 49 | 60mm thick machine pressed precast concrete ( M-35 grade) prepolished rubberized moulded interlocking paver block manufactured in an automatic plant working on vibration and simultaneous hydraulic compression from top, with grey cement and pigment(Yellow & red) any shape and size confirming to IS 15658-2006 laid over and including 50 mm thick cushion of coarse sand & filling the joints with dry cement and sand mortar 1:4 complete all as specified and as directed. |
| 50 | Filling the joints of floor trap / S trap etc with white cement complete all as spd and directed. |
| 51 | Filling the joints of floor of toilet, bathroom , kitchen etc with white cement complete all as spd and directed. |
| 52 | Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 0.70 kg per sq.m over cleaned and dry roof surface including parapet etc complete, all as specified and as directed by Engineer-in-Charge. |
| 53 | Water proofing treatment on roof/ sunken portion using APP polymeric ( on roof/sunken portion) water proofing membrane minimum 3 mm thick and weighting not less than 3.0 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm over cleaned surface including parapet, torching over laps with a propane or butan gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing all as per manufacturers instructions incl wire brushing and cleaning the top surfaces of concrete, roof surfaces etc. with water including flashings and junction of parapets etc complete all as specified and directed. |
| 54 | GI spout pipe 40 mm dia 400 mm long fixed in PCC 1:2:4 complete all as specified and directed by Engineer-in-Charge. |
| 55 | Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 56 | Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified and directed by Engineer-in-Charge. |
| 57 | Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Rendering 15 mm thick in cement mortar 1:4 over of brick or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Rendering 10 mm thick in cement mortar 1:3, on fair face of concrete surfaces ceiling etc.at any height and removing rubbish out of premise land all as specified and directed. |
| 60 | Rendering 10 mm thick in cement mortar 1:4 on on brick or concrete surfaces etc mixed with water proofing compound finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.NOTE: Water proofing compound shall be measured and paid separately. |
| 61 | Supply only liquid water proofing compound ISI Marked complete all as specified and directed. |
| 62 | Preparation of new plastered surfaces of wall and applying two coats of interior acrylic emulsion on walls over and including one coat of wall care putty using roller including preparation of surface complete all as specified and directed. |
| 63 | Preparation of old plastered surfaces of wall and applying two coats of interior acrylic emulsion on walls over and including one coat of wall care putty using roller including preparation of surface complete all as specified and directed. |
| 64 | Preparation of new plastered surfaces of ceiling and applying two coats of interior acrylic emulsion on ceiling over and including one coat of wall care putty using roller including preparation of surface complete all as specified and directed. |
| 65 | Preparation of old plastered surfaces of ceiling and applying two coats of interior acrylic emulsion on ceiling over and including one coat of wall care putty using roller including preparation of surface complete all as specified and directed. |
| 66 | Preparation of new plastered /concrete / unplastered surfaces and applying two coats of weather guard exterior acrylic emulsion paint (Ist quality) (Apex) any tint, over and including one coat of wall care cement based putty using roller on walls complete all as specified and directed. |
| 67 | Preparation of old plastered/ concrete/ unplastered surfaces and applying two coats of weather guard exterior acrylic emulsion paint (Ist quality) (Apex) any tint, over and including one coat of wall care cement base putty using roller on walls complete all as specified and directed. |
| 68 | Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 69 | Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. |
| 70 | Factory Made Solid PVC coloured Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed by Engineer-in-Charge. |
| 71 | 25 mm thick factory made Flush shutters for cupboard in two pieces, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with decorative face veneer with lipping/frame to match with 0.80 mm thick mica supplied and fixed with edge binding tape complete all as specified and directed by Engineer-in-Charge. |
| 72 | 35 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with decorative face veneer with lipping/frame to match with 0.80 mm thick mica supplied and fixed complete all as specified and directed by Engineer-in-Charge. |
| 73 | 35 mm thick factory made Plain, framed, panelled shutters of 2nd class Hardwood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkat complete all as specified and directed by Engineer-in-Charge. |
| 74 | 35 mm thick factory made Glazed & Skeleton shutters of 2nd class Hardwood (Except mango) open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size of stiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge. |
| 75 | Solid PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge. |
| 76 | Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge. |
| 77 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge |
| 78 | Providing & fixing false ceiling at all heights with semi perforated 12 mm thick micro tegular edged GRG (Glass Fibre With Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 4mm dia fully threaded hanger rod upto 1000 mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing all as specified and as directed by the Engineer-in-Charge. |
| 79 | 150 mm long extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed by Engineer-in-Charge. |
| 80 | Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge |
| 81 | 150 mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolt and fixed to shutter complete all as specified and as directed. |
| 82 | 200 mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolt and fixed to shutter complete all as specified and as directed. |
| 83 | 100 mm Butt hinges, medium weight, cold rolled Mild steel, and fixed with screws or with welding to existing MS frames complete all as specified and directed by Engineer-in-Charge. |
| 84 | 125 mm Butt hinges, medium weight, cold rolled Mild steel, and fixed with screws or with welding to existing MS frames complete all as specified and directed by Engineer-in-Charge. |
| 85 | 300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge. |
| 86 | 300 mm brass sliding door bolt with brass hasp, staple (bolt type) and fixing with rolled or drawn brass bolt and complete all as specified and as directed. |
| 87 | Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 140 mm complete all as specified and directed by Engineer-in-Charge. |
| 88 | Floor door stopper of brass body alloy and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 140 mm fixed in repair complete all as specified and directed by Engineer-in-Charge. |
| 89 | Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) 30 mm etc complete all as specified and directed by Engineer-in-Charge. |
| 90 | Supply and fixing in repair door closer (Aluminium die cast body) hydraulically regulated,designation No. 2,universal type, suitablefor door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed by Engineer-in-Charge. |
| 91 | Supply and fixing in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover,governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-Charge. |
| 92 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 93 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete fixed IN REPAIR all as specified and directed by Engineer-in-Charge. |
| 94 | Sheet glass 4 mm thick Figured glass pin head type, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane complete all as specified and directed by Engineer-in-Charge. |
| 95 | Sheet glass 5 mm thick tinted/plain/Figured glass type, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane complete all as specified and directed by Engineer-in-Charge. |
| 96 | Sheet glass 5mm thick tinted/plain/Figured glass type, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares exceeding 0.5 Sq. mtr in each complete all as specified and directed by Engineer-in-Charge. |
| 97 | Toughned glass 12mm thick as in hinged door, partitions, automatic doors and similar work including cutting to shape, drilling holes, grinding, polishing and rounding off edges of glass, glazing with beads fixed with stainless steel panel, pins any type spigot, frameless railing, L patch connector, top and bottom patch any type of pivot side panel connecting wall mounted over panel patch with pivot, bracket and all connected fitting for door and partition any required complete all as specified and directed. |
| 98 | Material and labour handle for toughned glass door H, C-type (ladder) pull handles: design. It feaures a straight cylindrical vertical bar extending past two distinct horizontal mounting posts, fitting for door and partition including required fitting complete all as specified and directed. |
| 99 | Supply and fixing in repairs drapery rods/ curtain rods stainless steel pipe (fancy type) 20-25 mm in dia with end SS brackets & knobs, funnels fixed with rawl plug and screws, including taking down old curtain rod/ wooden pelmet complete all as specified and directed. |
| 100 | Stainless steel work such as Frames, grills, gratings etc. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred doors; ladders; framed balusters; walk ways; railings work conforming to grade 304 complete all as specified and directed. |
| 101 | Mild Steel Framed work as in guard bars/grills, gratings, chowkhat etc. with ends of bars shouldered/ welded and/ or riveted, or forged into spikes; framed guard bars/grills conforming to Fe-290 (Gde E-165) complete all as as specified and directed by Engineer-in-Charge. |
| 102 | Steel tubular section of any size and shape including special shaped washer fixing in any position, gate, fram, wicket gate etc. complete using ERW or induction butt welded tubes conforming to IS grade St.-240 and fixing complete all as as specified and directed by Engineer-in-Charge. |
| 103 | Mild steel Framed work as in doors or gates and other required of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (including) of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete with Fe 290 (Gde-E-165) complete all as specified. |
| 104 | Pre- painted galvalume aluminum zinc coating profile sheet GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping s crews as complete all as specified and directed. |
| 105 | Fibre glass reinforced translucent corrugated sheet 2.0 mm thick of any colour as in roof covering/ cladding to wall with two corrugation side lap, fixed with coach screws and washer etc complete all as specified and as directed by Engr-in-charge. |
| 106 | Fibre glass reinforced translucent plain steel sheet 2.0 mm thick of any colour as in roof covering/ cladding to wall, fixed with 100mm side lap fixed with coach screws and washer etc complete all as specified and as directed by Engr-in-charge. |
| 107 | Supply and fixing in repairs 18 to 20 mm thick block board core and plywood face panels, commercial type with 0.80 mm mica on both sides any colours and fixed with screws in cup board shutters/ shelves and kitchen cabinets including 0.80 mm thick PVC edge binding tape around beading each shutter incl taking down cup board shutter, cabinat with frame and shelves complete all as specified and directed. |
| 108 | Provding and fixing 0.80 mm thick 18 to 20 mm wide PVC edge binding rape of approved quality for cupboard / wardrobe shutters including necessary synthetic resin hot pressed to edge on binding machine etc. complete all as sepcified and directed. |
| 109 | Supplying and fixing Aluminium Composite Panel (ACP) cladding for external surfaces, conforming to the following technical parameters as per the manufacturer's (ALEX) specifications:1. Material Composition • Panel Thickness: Total panel thickness of 6.0 mm.• Aluminium Skin: High-grade aluminium skin with a thickness of 0.50 mm on both the top and bottom coils (conforming to Type J/Exterior Grade). • Core Material: Pure Polyethylene (PE) Core sandwiched between two aluminium skins with high-performance adhesive films. Coating & Surface Finish: • Exterior Finish: Top surface coated with PVDF (70% Kynar-500) three-layer paint finish and lacquering for superior weather resistance and UV protection. • Coating Thickness: Top coil coating thickness between 25μ - 28μ; bottom coil provided with a 7μ service coat.• Protection: Visible surface protected by a branded protective film to be removed only after final installation. Fabrication: • Panels shall be cut, drilled, punched, or stamped as per the architectural drawings. • Bending, routing and 90° bending to be executed precisely without loss of surface integrity or cracking of the PVDF coating. Framework & Sub-structure: • Aluminium grid: The sub-structure shall consist of extruded aluminium square/rectangular tubes. • Brackets: Heavy-duty G.I. or aluminium “L” cleats/brackets fixed to the masonry/RCC backup wall using metallic expansion fasteners. Alignment: • The framework must be perfectly plumbed and leveled using laser levels or water tubes. Fabrication & Installation: • Panels shall be fabricated using the “Tray” or “Box” method. • Edges shall be routed and folded to form a 25–30 mm flange. Fixing: Folded edges are to be secured to the aluminium grid using stainless steel (SS) screws or rivets at intervals not exceeding 300 mm. Joints & Sealing: • Maintain a uniform groove/joint (typically 8–12 mm) between panels. • Joints must be cleaned and filled with Non-Staining Weather Silicone Sealant (e.g., Dow Corning or equivalent) over a closed-cell polyethylene backing rod. Measurement & Payment: • The measurement shall be taken on the finished visible surface area in Square Meters (Sqm). • The rate shall include the cost of ACP sheets, aluminium framework, joint sealing, wastage, fabrication, scaffolding, specialized labor, removal of the protective film, and all necessary fittings and fixtures. |
| 110 | PVC solid wall panelling 5mm thick any colour/ design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site and including 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed. |
| 111 | PVC hollow wall paneling 7 to 8 mm thick any colour/design approved by Engr-in-Charge, includive of fixing arrangement, PVC fillet 35 mm wide etc on to wall including moulding end caps fixing with PVC sleeves and screws as required at site complete all as specified and directed. |
| 112 | Supply and fixing in repair 100 mm Brass handles, cast type, polished bright finish handle for cabinet shutter complete all as specified and directed. |
| 113 | Supply and fixing in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, bright finished complete all as specified and directed. |
| 114 | 100 mm Mild steel Hasp and staple, safety type, hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 115 | Stainless steel auto close (dadu) hinges suitable for PVC moulded shutter fixed in position with stainless steel screws, complete all as specified and directed.Make:-Godrej, Helttich india, EBCO. |
| 116 | 50mm long magnatic catchers brass alloy body superior quality and fixed with screws complete all as specified and directed. |
| 117 | Supply and fixing in repair telescopic channel/slider to fiacilitate drawer slide on steel ball bearing 400-500 mm long and fixed in position with stainless steel screws , ISI marked , suitable for cupboard drawers , complete as per the sample kept in the office of Engr-in-charge.Make:-Godrej, Helttich india, EBCO. |
| 118 | Supply and fix in repairs aluminium mortice lock, vertical type size 65mm, 2 lever complete all as specified and directed. |
| 119 | Supplying and fixing in existing position new Vitreous China Wash down water closet (Pedestal pattern), white including plastic seat cover white and PVC P or S trap and connection to outgoing pipe, flushing pipe, anti syphonage pipe and jet complete all as specified and directed by Engineer-in-Charge. |
| 120 | Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white fixed in repairs, with integral foot rests with 'P' or 's' trap, front or back inlet (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed. |
| 121 | Vitreous China urinals,half stall urinal type white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed by Engineer-in-Charge. |
| 122 | Supplying and fixing in repairs Vitreous China wash down water closet pan including connection to drain or out going pipes single piece with PVC hydrolica plastic water closet seat cover complete all as specified and directed. |
| 123 | 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe IN REPAIR complete all as specified and directed by Engineer-in-Charge. |
| 124 | Supplying and fixing in repairs hydrolica plastic water closet seat cover white coloured closed pattern with flat bottom with mild steel chromoum plated hinge device for pedestal pan complete all as specified and directed by Engineer-in-Charge. |
| 125 | Supplying and fixing plastic seat cover white/coloured (as required at site) for water closet closet padestral pattern with flat bottom and steel chromium plated hinging device including taking out old seat cover complete all as specified and directed. |
| 126 | Vitreous china white wash basin (flat back or angle back type) of size 550mmx400mm coloured including MS brackets, waste coupling PTMT, and waste pipe PVC 32 mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified and as directed. |
| 127 | Vitreous china white wash basin with pedestal, flat back type of size 550mmx400mm coloured including MS brackets, cutting for and pinning in ends of brackets, including PVC waste pipe as in repairs complete all as specified and as directed. |
| 128 | Supply and fixing in repairs vitreous china wash hand basin of size 600 mm x 425 mm x 195 mm counter basin oval shape with coupling and grating and connection to drain pipe complete all as specified and directed. |
| 129 | Supply and fixing in repair Urinal partition of frosted glass of 8 mm thick of height 1.20 mtr in any shape fixed with chromium finish clamps complete as specified and directed |
| 130 | Supply and fixing in repairs chromium plated Urinal spreader for fixing with 15 mm dia bore pipe complete all as spd and directed by Engr-in-charge. |
| 131 | Supply and fixing in repair wash basin table top size (175x440x420mm or 135x420x420mm) w/o overflow/ complete all as specified and directed. |
| 132 | Supply and fixing PVC syphon kit in repair suitable for one piece wc cistern and wall mounted wc flushing cistern complete kit ISI mark complete all as specified and directed. |
| 133 | Supply and fixed in repair Brass chromum plated 3‐In‐1 System wall mixer with Provision for both hand shower and overhead Shower for mixing hot and cold water fancy type with screwed down for 15mm dia iron pipe With 115mm Long Bend Pipe, Connecting Legs & Wall Flange complete all as specified and directed by Engineer-in-Charge. |
| 134 | Supply and fixing in repair brass chromum plated single lever centre hole basin mixer without popup waste system wround spout with 375 mm long braided hoses complete all as specified and as directed. |
| 135 | 15 mm fancy type chromium plated fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. |
| 136 | Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge. |
| 137 | Supplying and fixing in repairs fancy type Angle valve/ stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup complete all as specified and directed by Engineer-in-Charge. |
| 138 | Gun metal gate or globe valves heavy duty quarter turn type, full way openig with iron wheel head screwed with both end of GI tubing 15 mm bore ISI marked including taking down of unserviceable gate or globe valve all as specified and directed. |
| 139 | Gun metal gate or globe valves heavy duty quarter turn type, full way openig with iron wheel head screwed with both end of GI tubing 20 mm bore ISI marked including taking down of unserviceable gate or globe valve all as specified and directed. |
| 140 | Supply and fixed in repair spray jet brass chromium plated including suitable length of PVC connection pipe complete all as specified and directed by Engineer-in-Charge. |
| 141 | Health faucet (ABS Body) hand shower mild steel chromium plated suitable for 8 mm dia pipe with 1 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect all as specified and directed by Engineer-in-Charge'. |
| 142 | Supply and fixing in repairs hand shower of size 25 mm x 38 mm oval shape single flow (ABS body and face plate) chromium plated with rubit cleaning system complete all as specified and directed. |
| 143 | Cast copper alloy chromium plated Towel Rack with lower hanger (stainless steel) with hooks, complete all as specified and directed. |
| 144 | Towel Ring of chromium plated fixed with and including Chromium plated brass screws and wooden/ plastic cleats (Minimum weight 90gms) |
| 145 | Chromium plated brass fancy type soap dish holder of approx size 160 x160 x 90 mm, complete all as specified and as directed. |
| 146 | Supplying and fixing in repairs Soap Dispenser with metallic bolt complete all as specified and directed by Engineer-in-charge. |
| 147 | Supply and fixing tumbler holder complete all as specified and directed. |
| 148 | Supply and fixing in repairs toilet paper holder chromium plated with fixing to wall complete all as specified and directed. |
| 149 | Supply and fixing in repair brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flange, Complete all as specified and as directed |
| 150 | Supply and fixing glass shelf assembly 5.5mm thick, 12 cm wide and 60 cm long fixed with & including chromium plated brass screws and stainless steel cleats and frame (Minimum weight 300gms) fixed in repair complete all as specified and as directed. |
| 151 | Supply and fixing corner glass shelf assembly 5.5mm thick (set of three of size 250 X 250 mm, 200 X 200 mm & 150 X 150 mm ) fixed with & including chromium plated brass screws and stainless steel cleats and frame (Minimum weight 300gms) fixed in repair complete all as specified and as directed. |
| 152 | Supply and fixing 6mm thick selected quality glass frameless high quality bevelled edge mirror fancy type with etching fixed to wall with stainless steel studs any size complete all as specified and directed. |
| 153 | Supply and fixing in repair PVC waste pipe 32mm dia, 800mm long with cup and nuts complete all as specified & directed |
| 154 | Stainless steel grating 100 mm dia with locking system complete all as specified and directed by Engineer-in-Charge. |
| 155 | PVC connections 15mm size with PTMT nuts of length 450 mm fixed in repair complete all as specified and directed by Engineer-in-Charge. |
| 156 | Supply and fixing 15mm bore steel water tubing medium grade, galvanized with all fittings and fixture fixed & concealed in wall/ceiling or laid in floors complete all as specified and as directed. |
| 157 | Fixing only GI water Tubing 15 mm 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors on walls including clamps complete all as specified and directed by Engineer-in-Charge. |
| 158 | Supply and fixing for tubes 20 mm, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including in short lengths standard clamps and screws fixed on rawal plugs Complete. |
| 159 | Fixing only steel water Tubing 20 mm 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors on walls including clamps complete all as specified and directed by Engineer-in-Charge. |
| 160 | 110 mm bore, PVC (SWR) pipes with pressure rating not less than 6 Kg/sqcm single socketed, in any length with solvent 3 to 5 cm gap between wall and pipe, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts or laid in trenches complete all as specified and directed by Engineer-in-Charge. |
| 161 | 75mm bore, PVC (SWR) pipes with pressure rating not less than 6 Kg/sqcm,single socketed, in any length with solvent 3 to 5 cm gap between wall and pipe, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts or laid in trenches complete all as specified and directed by Engineer-in-Charge. |
| 162 | PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore including jointing to waste pipe in cement concrete type B-1 (1:2:4) of size 200 mm x 200 mm x 250mm fixed in repair laid in trenches complete all as specified and directed by Engineer in Charge. |
| 163 | PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge. |
| 164 | PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge. |
| 165 | PVC (SWR) junction single,(Single T) equal or unequal for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge. |
| 166 | PVC (SWR) junction single,(Single T) equal or unequal for 110 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge. |
| 167 | Supply and fix in position alphabetical letters in Hindi ,English and punjabi made of stainless steel sheet of grade SS - 304L of thickness 1.25 mm and fixing to MS Sheet claddig with necessary fixing arrangements , size of each letter height exc 10cm but not exc 80cm , width as per font and depth 40 mm complete all as specified and as directed. |
| 168 | INTERNAL ELECTRIC SUPPLY WORKS |
| 169 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including ,fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. all as specified and directed. |
| 170 | Taking down carefully copper/ aluminium sub main wiring complete, including existing batten/ conduit etc. removing materials deposited in store for keeping in safe custody and making good disturbed surfaces of walls, floors etc. complete all as specified and directed. |
| 171 | Taking down old unserviceable light fittings any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed by Engineer-in-Charge to match with existing surface all as directed. |
| 172 | Taking down MCB DB/ TPN along with MCBs of any size and removal from site and making good disturbed surfaces complete all as specified and directed. Please Enable Macros to View BoQ information |
| 173 | Taking down MCB DB/ TPN along with MCBs of any size and removal from site and making good disturbed surfaces complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 19, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 31, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 6 days
Aug 31, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 6 daysAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysSep 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender