Tender For Provn Of Certain Minor Works (Mw-02, 03, 05 & 06) (B/R) At Air Force Station Highground Under Age(I) Highground
Tender Value
9.04 Lakhs
Estimated cost
Bid Submission
01 Sep 2026
7 days left
EMD
18100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Certain Minor Works (Mw-02, 03, 05 & 06) (B/R) At Air Force Station Highground Under Age(I) Highground
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in post holes (for similar holes) each not exceeding 0.5 cum getting out, returning filling in and ramming earth or broken rubbed mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 metre and making good surface in soft/loose soil complete all as specified and directed. |
| 2 | Material and Labour for cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 3 | Supply and Fix rolled sections as in main and cross beams, hop and jack rafters, purlins where connected to common rafters and running rails and guiders for sliding doors fixed with angle cleats or other connecting plates, conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed. |
| 4 | Supply and Fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 5 | Material and Labour for preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide complete all as specified and as directed. |
| 6 | Supply, fabrication and fixing MS framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikers framed guard bars, MS square mesh of reqd size as gril, barred iron doors ladders; framed balusters walk ways railings framework of watertanks and similar work conforming to Fe-290 Gde-165 including making good to damaged portion complete all as specified and as directed. |
| 7 | Supply and fixing powder coated aluminium grill of approved design /pattern with approved standard section and fixed to the existing window frame with C.P. brass /stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and opration of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement complete all as specified and directed. |
| 8 | Material and Labour for plain cement concrete (1:3:6), type C-0, (using 12.5mm graded crushed stone aggregates) as in bed block, blocks for holdfasts, filling in pressed steel door frames , benching slightly rounded or chamfered angles & throating etc including necessary use & waste of form work complete all as specified and directed. |
| 9 | Cutting holes in brick walls exc half brick but n exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed. |
| 10 | Material and Labour for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 11 | Material and Labour for brickwork with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed. |
| 12 | Material and Labour for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 13 | Material and Labour for formwork to soffits and sides of flat suspended slabs such as roof slabs, floor slabs landings and similar works not exceeding 200 mm thick (Horizontal or sloping) complete all as specified and directed. |
| 14 | Supply and Fix mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (anealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 15 | Material and Labour for 18-20 mm thick granite (of any type) work (table, rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) incl pointing in white cement (1:2) using mable dust with admixture of pigments to match with shade of granite complete all as specified and directed. |
| 16 | Taking down cement plaster on brick or stone walls etc, incl raking out joints, hacking for key scrubbing down with water, etc. |
| 17 | Material and Labour rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 incl finished even and smooth (without using extra cement) complete all as specified and directed. |
| 18 | Material and Labour preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion white or tint with priming platered and other surfaceswith chalk whiting on plastered surface complete all as specified and directed. |
| 19 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing servicieable tiles to store and rubbish off the premises complete all as specified and directed. |
| 20 | Supply and Fix for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed. |
| 21 | Supply and Fix for coloured Glazed ceramic tile in verticle surface 300x600x7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick plastering as backing coat in cement mortar 1:4 complete all as specified and as directed. |
| 22 | Supply and fixing kitchen sinks with drainage board out of Stainless steel 1.00mm thick with plugs, washers and waste pipes including bedding in cement mortar to dwarf wall or including fixing cantilever brakets including and connecting union to pipe over all size 915mm X 460mm bowl size 410mm X 330mm X 160mm incl waste pipe complete all as specified and directed. |
| 23 | Supply and Fix 15 mm bore Fancy type Bib taps, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 24 | Material and Labour 15 mm water tube medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 25 | Material and Labour 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified & directed. |
| 26 | Supply and Fix 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed. |
| 27 | Supply and Fix 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, clamps fixed to walls complete all as specified & directed. |
| 28 | Supply and Fix 75 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed. |
| 29 | Supply and directed F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 30 | Supply and fix in position aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) three track window (two shutters glazed & one shutters wiregauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm (Section No 20832) (c) Top & side Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20738) (d) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.45 mm (Section No 20737) (e) Bottom Members of shutter section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20736)complete all as specified and directed. Note: Section no given above are of make Jindal, contractor may luse similar section of other make mention in Appx B. |
| 31 | Supply and Fix Prelaminated particle board 9mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed. |
| 32 | Supply and Fix Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, entilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions. |
| 33 | Supply and Fix 4.8 mm thick sheet glass tinted and fixed with aluminium door/window having area not exc, 0.50 sqm in each pane complete all as specified and directed. |
| 34 | Supply and Fix Powder coated aluminium (minimum thickness of powder coating 50 micron) aluminium door shutters, aluminium section having min thickness 2mm including necessary joining cleats,glazing clips,ruber neoprene packing, handles 2Nos in each shutter, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed. |
| 35 | Supply and Fix 200 mm long aluminium anodised barrel tower bolts and extrude section and fixed complete all as specified and as directed. |
| 36 | Supply and Fix Aluminium (extruded section) body door closer hydraulically regulated, designation No.3, universal type, suitable fordoor shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. |
| 37 | Supply and Fix 250mm length of bolt, aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & as directed. |
| 38 | Supply and Fix 140 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 39 | Taking down chowkat or frames with shutter (without taking off shutters from the frame) not exc 1.5 sqm each complete all as specified and directed. |
| 40 | Taking down chowkat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 Sqm complete and directed. |
| 41 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 42 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground floor) complete all as specifed and directed. |
| 43 | Dismantling asbestos cement (corrugated, semi corrugated etc,) sheets in roof covering complete all as specified and directed. |
| 44 | Dismantling wrought iron or mild steel works of any description not otherwise provided for complete all as specified and directed. |
| 45 | Material and Labour reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in foundation, incl rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs under reamed piles and mass concrete complete all as specified and directed. |
| 46 | Material and Labour for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels and the like complete all as specified and directed. |
| 47 | Use and waste for fair finished formwork to sides of flat concrete foundations, footings, based of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed. |
| 48 | Material and Labour formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal of slopping, and similar work all exceeding 20 cm wide. (where RCC/PCC bands in walls, spanning and opening, the formwork soffit complete all as specified and directed. |
| 49 | Supply and Fix mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (anealed) not less than 0.9 mm dia or securing with clips all as specified and directed. |
| 50 | Supply and Fix mild steel TMT bars 5mm dia and over upto and incl 10 mm dia, cut to length, bent to shape required, incl cranking, bending spirally for hooping for in stirrups, spaces and binders and incl mild steel wire (anealed) not less than 0.9 mm dia or securing with clips complete and directed. |
| 51 | Material and Labour hardcore of broken stone or boulders of gauge n.exc 63mm deposited spread and leveled in layer n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 52 | Material and Labour 100 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded crushed stone aggregate), as in sub base of floors complete all as specified and directed. |
| 53 | Material and Labour for machine cut kota stone slab flooring 18-20 mm thick over 20 mm thick cement screed base of cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade to the slab incl rubbing and polishing complete all specified and directed. |
| 54 | Material and Labour for machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick cement screed of cement mortar 1:3 and jointed with grey cement slurry mixed with pigment to match the shade to the slab incl rubbing and polishing complete all as specified and directed. |
| 55 | Supply and fix, factory made pressed steel frames for doors with one or more rebates, of size 105mmx60mm, made out of 1.25mm thick sheet, including necessary fixing lugs, hinges, lock strike plate, with and including cement concrete 1:2:4 (type B-0) with 12.50 mm graded stone aggregate in backfilling of chowkhats etc, complete all as specified and directed. |
| 56 | Supply and fix, factory made flush shutters 35 mm thick,solid core construction with block board core and plywood face panels commercial type on both sides, duly provided with 6mm thick Teakwood leeping on edges alround, fitted to chowkats, complete all as specified & directed. |
| 57 | Supply and fix Factory made box type steel window with pintle hinges & 1 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars, dovetailed or welded and with one shop coat of zinc chromate primer cement concrete 1:2:4 (type B0) with 12.50 mm graded stone aggregate in backfilling of chowkhats and hold fast etc complete all as specified and directed. |
| 58 | Supply and Fix 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed. |
| 59 | Supply and fix 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete and directed. |
| 60 | Material and Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 incl finished even and smooth (without using extra cement) complete all as specified and directed. |
| 61 | Material and Labour for providing cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) in lintel upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, stringcourses lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates,kerbs incl weathering slightly rounded or chemfered angles and throating complete all as specified and as directed. |
| 62 | Material and Labour for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed. |
| 63 | Material and Labour for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of whtie wash complete all as specified and directed. |
| 64 | Material and Labour for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 65 | Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in any soft/loose soil complete all as specified and directed. |
| 66 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pathern over and incl 50mm thick compacted bed of fine sand, compacting and proper embedded/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 67 | Material and Labour for 75 mm thick, PCC 1:3:6 type C1 (using 20mm graded stone aggregate), finished even and smooth without using extra cement.as in plinth protection incl joints filling complete all as specified and directed. |
| 68 | Material and Labour for point wiring for light/fan, surface/concealed type (as per site requirement) with 3 x 2.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLSH copper conductor cable (phase, neutral & earth wire), earth wire shall be connected to common earth and earth duly with suitable copper lugs drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with all PVC conduit accessories, 1.60 mm thick GI modular metal flush box with plastic laminated sheet cover or surface mounting plastic/ PVC boxes suitable for modular switches/ sockets with cover plates (modular type), blanking plates, brass screws, cup washers, gypsum screws and connected items including all cutting/ chases etc in walls/ wall panels and making good to the disturbed surfaces to match the existing complete all as specified and as directed. |
| 69 | All as per item No 68.00 here-in-above but for one socket outlet point 5 Amps on independent board complete all as specified and directed. |
| 70 | All as per item No 68.00 here-in-above but with 2.5 sqmm cable for 3 pin 15/16 amps switch socket outlet complete all as specified and directed. |
| 71 | Supply and fix Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, incl making hole in wall and make good as existing incl dismantling and taking down old unsv complete all as specified and directed. |
| 72 | Supply and fix in repair modular switch 1 way 6A, single module complete all as specified. |
| 73 | Supply and fix in repair modular switch 1 way 16A, single module complete all as specified. |
| 74 | Supply and Fix in repair modular socket outlet 3 pin, 6A, two module, shuttered socket complete all as specified. |
| 75 | Supply and Fix modular socket outlet 2-in-1, 3 pin, 6/16 Amp, two module, shuttered socket complete all as specified and directed. |
| 76 | Supply and fix sheet metal enclosures distribution board SPN 4 ways double door , 200 amp bus bar, IP 43 protection, 240 volts, with shrouded neutral bar & insulated bus bar and earth link, suitable for MCBs/ RCBOs as incomer and out going complete dully grouted on the wall (flush) incl dismantling and taking down old unsv and making connections with suitable size of lugs and making good the disturbed surface matchig with existing surface all as specified and directed. |
| 77 | Supply and fix MCB single pole 240 volts, 50Hz , breaking capacity 10KA, C curve 6A to 32A, ISI marked all as specified and as directed. |
| 78 | Supply and fix MCB SPN 240 volts, 50Hz, breaking capacity 10KA, c curve 32 A, ISI marked all as specified and as directed. |
| 79 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 80 | Note: The total amount shall subject to adjustment of credit of Rs 9137.21 for old Materials as per Schedule of Credit Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysSep 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender