Tender For Repairing Of Horizontal Girder Along With Change Of Rubber Seal Of Mahanadi Barrage Spillway Gate No. 10,15, 23, 44, 46, 69, 76 And Under-Sluice Gate No. 05 For The Year 2026-2027.
Tender Value
90.13 Lakhs
Estimated cost
Bid Submission
24 Aug 2026
0 days left
EMD
90140
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Cuttack → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing Of Horizontal Girder Along With Change Of Rubber Seal Of Mahanadi Barrage Spillway Gate No. 10,15, 23, 44, 46, 69, 76 And Under-Sluice Gate No. 05 For The Year 2026-2027.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling damaged Top and Bottom Horizontal Girder web plate, stiffeners angles of Spillway gate no- 10,15, 23, 44, 46, 69, 76 and Undersluice gate no -05 etc. by way of gas cutting mahine , supplying & cutting steel materials to required size, fabrication & erection of the same and then grinding, polishing by the help of jhula, temporary walkway bridge,safety belt,helmet, ladders. including cost of materials, loading, unloading, consumable, T&P & cess etc complete but excluding GST as per direction of the Engineer-in-Charge. |
| 2 | Supplying and fixing of rubber seal \\"P\\"type side seal (P53 x 110 x 12mm) & Bottom seal (75mm x 12mm) to Mahanadi Barrage spillway gates after gas cutting of old nuts & bolts including cost of materials,conveyance,T&P, scaffolding, labour etc complete but excluding GST as per direction of the Engineer-in-Charge. |
| 3 | Supplying and fixing of rubber seal \\"P\\"type side seal (P53 x 110 x 12mm) & Bottom seal (75mm x 12mm) to Mahanadi Barrage undersluice gates after gas cutting of old nuts & bolts including cost of materials,conveyance,T&P, scaffolding, labour etc complete but excluding GST as per direction of the Engineer-in-Charge. |
| 4 | Surface preparation for painting manually and by power tool cleaning, such as scrapping, wire brushing, machine brushing and grinding. Prior to hand and power tool cleaning, any heavy layer of rust should be Surface preparation for painting manually by power tool cleaning, such as scrapping, wire brushing and grinding, Prior to hand and power tool cleaning any heavy layer of rust should removed by chipping, visible oil, grease, dirt and other foreign materials should be cleaned by using solvents by the use of clean mineral spirits xylol or white gasoline. After hand and power tool cleaning, the surface should be cleaned of loose dust and debris from the entire surface for exposure of the base material of the entire gates componenets such as skin plates, girders, stiffeners etc. as per the drawing. Before application to primer coat an absorbent is to be applied to remove very fine dust as per direction of the Engineer-in-Charge. The rate in inclusive of cost of materials, conveyance, cost of T&P materials, scaffolding, labour charges etc. complete. |
| 5 | Supplying and applying one coat Epilux 4 Zinc Rich Epoxy primer in dual pack (base and hardner) to give minimum 40±5 microns dry film thickness per coat as per on the previously cleaned surface immediately after surface preparation but not later than a time gap of six hours on the complete surface of the gates components such as skin plates, girder & stiffener etc. complete as per the direction of Engineer-in-Charge. |
| 6 | Supplying and applying first coat of Epilux 555 high build coltar Epoxy black paints available in dual pack (base and hardner) to give minimum 150±5 microns over the primer coating on the complete gate surfaces and its components complete with cost of materials, labour charges, scaffolding, T&P materials staging etc. complete as per the direction of Engineer-in-Charge. |
| 7 | Supplying and applying second coat of Epilux 555 high build coltar Epoxy black paints available in dual pack (base and hardner) to give minimum 150±5 microns over the first coat on the complete gate surfaces and its components complete with cost of materials, labour charges, taxes scaffolding, T&P materials staging etc. complete as per the direction of Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayAug 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender