Tender For Repair/ Maintenance Of Water Supply Distribution Network, Solar Water System And Allied Works At Jalipa Mil Stn And Various Acon Nodes Under Ge (A) Barmer
Tender Value
28 Lakhs
Estimated cost
Bid Submission
31 Aug 2026
8 days left
EMD
56000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Barmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Maintenance Of Water Supply Distribution Network, Solar Water System And Allied Works At Jalipa Mil Stn And Various Acon Nodes Under Ge (A) Barmer
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation, taking up/down or laying of GI tubing/CI pipe etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and directed by Engineer-in-charge. |
| 2 | Returning, filling in, including, spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed by Engineer-in-charge. |
| 3 | Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge. |
| 4 | Taking up or down GI steel tubing including fittings with connection from trenches, walls, floors etc including cleaning for re-fixing or remove to store yard/ credited to contractor complete all as specified and directed complete all as specified and as directed for the following sizes : |
| 5 | GI pipe 100 mm bore |
| 6 | GI pipe 80 mm bore |
| 7 | GI pipe 50 mm bore |
| 8 | GI pipe 40 mm bore |
| 9 | GI pipe 25 mm bore |
| 10 | GI pipe 20 mm bore |
| 11 | GI pipe 15 mm bore |
| 12 | Supplying, laying , jointing and testing GI tubes, medium grade (ISI marked), galvanized iron with and including all fitting (ISI marked) such as bends, tees, sockets, nipples & unions, flanges etc laid in trenches/fixed to wall/fixed on pillars etc complete all as specified and as directed of following sizes :- MAKE :Tata/Prakash/Jindal |
| 13 | GI pipe 100 mm bore |
| 14 | GI pipe 80 mm bore |
| 15 | GI pipe 50 mm bore |
| 16 | GI pipe 40 mm bore |
| 17 | GI pipe 25 mm bore |
| 18 | GI pipe 20 mm bore |
| 19 | GI pipe 15 mm bore |
| 20 | Laying, jointing and testing of GI water tubing medium grade (ISI marked) laid in trenches or fixed to wall with medium grade galvanised iron fitting (ISI marked) such as bends, tees, sockets, nipples & unions, flanges etc and connecting complete GI tubing , complete all as specified and directed..(Note :- Serviceable GI tubing obtained from taking up or down here-in before shall be re-used in this items.) |
| 21 | GI pipe 100 mm bore |
| 22 | GI pipe 80 mm bore |
| 23 | GI pipe 50 mm bore |
| 24 | GI pipe 40 mm bore |
| 25 | Supply and fixing in replacement gun metal globe / gate valve heavy duty with iron wheel head, screwed both ends for jointing iron pipe and fixed complete all as specified and as directed suitable for following sizes. Make - Zoloto/Sant/Kirloskar |
| 26 | 50 mm bore |
| 27 | 40 mm bore |
| 28 | 25 mm bore |
| 29 | 20 mm bore |
| 30 | 15 mm bore |
| 31 | Taking up or down cast iron/DI pipe (including all fittings) with connection from trenches, walls, floors etc including removal from site with cleaning for re-fixing or remove to store yard/ credited to contractorcomplete all as specified and as directed for the following sizes :- |
| 32 | CI/DI pipe 200 mm bore |
| 33 | CI/DI pipe 150 mm bore |
| 34 | CI/DI pipe 100 mm bore |
| 35 | Supply, lay, jointing and testing ductile iron pipes with spigot & socket ends of following sizes, class K7, centrifugally cast (spun) conforming to IS 8329/2000 with cement mortar lining inside surface of pipe with portland slag cement and externally metalic zinc coating as per IS 8329 including suitable rubber gasket joints, in any length, laid to level or to falls in trenches/on grounds/on support/stand complete all as specified and to the entire satisfaction of the Eng-in-Charge. MAKE : Tata/Jindal/Electrosteel. |
| 36 | 200 mm bore |
| 37 | 150 mm bore |
| 38 | 100 mm bore |
| 39 | Laying, jointing and testing of DI pipe of follwing bore sizes with spigot and socket ends, centrifugally cast, suitable for tyton joints, in any length, laid in trenches at same location complete all as specified and directed by Engineer-in-charge.Note :- Serviceable Pipe obtained form taking down shall be reused. |
| 40 | CI/DI pipe 200 mm bore |
| 41 | CI/DI pipe 150 mm bore |
| 42 | CI/DI pipe 100 mm bore |
| 43 | S&F ductile iron fitting conforming to IS 9523, suitable for spigot and socket pipes/ Flanged type of class K7 up to 200 mm bore such as bends (any type radius and angle), tappers any type (straight bend increasing, decreasing or double socket etc), TEE pieces, Single branch, Y junction double branch, Cross collars, caps, plugs etc. including rubber gasket joints incl testing & taking down old unsv fittings complete all as specified and to the entire satisfaction of the Eng-in-Charge. MAKE : Tata/Jindal/Electrosteel. |
| 44 | Detecting the leakage from UG DI/CI pipes up to 200 mm bore and rectifying the leakage by burning out existing lead and making joint by means of D joints, clamps, sockets etc, including cutting/threding of pipes and other allied works, excavation and earth work in any type of soil complete all as specified and as directed. |
| 45 | Detecting the leakage from UG DI/CI pipes up to 150 mm bore and rectifying the leakage by burning out existing lead and making joint by means of D joints, clamps, sockets etc, including cutting/threding of pipes and other allied works, excavation and earth work in any type of soil complete all as specified and as directed. |
| 46 | Detecting the leakage from under ground GI pipes up to 80/100 mm bore and rectifying the leakage by replacing, sockets, unions etc, including cutting/threding of pipes and other allied works, excavation and earth work in any type of soil complete all as specified and as directed. |
| 47 | Material and labour for Drilling and tapping DI/Cast iron water main( in position) for branch connections of the internal dia 15 MM complete all as specified and directed. |
| 48 | All as per item no 15 here in above but 20mm dia. |
| 49 | M & L cutting CI/DI pipes in position for insertion of new Tees, branches etc of dia 80 mm complete all as specified and as directed. |
| 50 | M & L cutting CI/DI pipes in position for insertion of new Tees, branches etc of dia 100 mm complete all as specified and as directed. |
| 51 | M & L cutting CI/DI pipes in position for insertion of new Tees, branches etc of dia 150 mm complete all as specified and as directed. |
| 52 | Supply, install, commissioning & testing of CI Sluice Valve of following sizes, both ends flanged, class PN 1.6, ISI marked conforming to IS 14846:2000 with SS spindle and one number hand wheel including making new flanged joints with rubber gasket, necessary bolts, nuts, washers etc of suitable size incl taking down old unsv one complete all as specified and to the entire satisfaction of the Eng-in-Charge. Make -Zoloto/Leader/Kirloskar |
| 53 | 300 mm bore |
| 54 | 200 mm bore |
| 55 | 150 mm bore |
| 56 | 100 mm bore |
| 57 | 80 mm bore |
| 58 | M&L for construction of brick masonary valve pit of internal dimensions 1200 mm x 1200 mm x 1200 mm complete and fabrication of 4.0 mm thick MS Sheet cover and angle iron frame made out of 40mm x 40mm x 6 mm MS angle iron and one side provided with hinge with locking arrangement & duly painted with two coats of black bituminous paint over a coat of red oxide primer including necessary earth work and PCC work complete all as specified and as directed. |
| 59 | M&L for construction of brick masonary valve pit of internal dimensions 900 mm x 900 mm x 900 mm complete and fabrication of 4.0 mm thick MS Sheet cover and angle iron frame made out of 40mm x 40mm x 6 mm MS angle iron and one side provided with hinge with locking arrangement & duly painted with two coats of black bituminous paint over a coat of red oxide primer including necessary earth work and PCC work complete all as specified and as directed. |
| 60 | Supply and Fix following items all as directed: |
| 61 | (a) Rubber Gasket 3 mm Thick Good Quality |
| 62 | (b) Patch Clamp for 150/200 mm dia pipe |
| 63 | (c) Patch Clamp 100 Mm dia |
| 64 | (d) Gland packing 12 mm size |
| 65 | (e) Gland packing 10 mm size |
| 66 | (f) Gland packing 08 mm size |
| 67 | Supply and fix in repairs MS bolts and nuts with washers factory made of any size fixed in any position complete all as specified and directed by Engineer-in-charge. |
| 68 | Supply, install, testing & commissioning of CI Non-Return (Reflux) Valve 80 mm bore, both end flanged, ISI marked conforming to IS 5312 (Part I & II) including making new flanged joints with rubber gasket, necessary bolts, nuts, washers etc of suitable size incl taking down old unsv one complete all as specified and to the entire satisfaction of the Eng-in-Charge. Note:- The rate quoted by contractor is deemed to be inclusive of Cutting and making new flanged in existing line at both end for installing NRV. |
| 69 | Supply, install, testing & commissioning of CI Non-Return (Reflux) Valve 100 mm bore, both end flanged, ISI marked conforming to IS 5312 (Part I & II) including making new flanged joints with rubber gasket, necessary bolts, nuts, washers etc of suitable size incl taking down old unsv one complete all as specified and to the entire satisfaction of the Eng-in-Charge. Note:- The rate quoted by contractor is deemed to be inclusive of Cutting and making new flanged in existing line at both end for installing NRV. |
| 70 | Taking out sluice valves for reparing / refacing / regrinding complete all as required and refixing the same in position after necessary repairing for 80 mm bore complete all as specified and as directed :- |
| 71 | All as per item No. 27 here in before but size100 mm bore. |
| 72 | All as per item No. 27 here in before but size150 mm bore. |
| 73 | Supply and fixing in repair check nut suitable for spindle of size 300/200/150/100/80 bore all as specified and directed by Engineer-in-Charge |
| 74 | Dismantling the existing unserviceable Foot Valve complete and S & F Cast iron Foot Valve Ball type with flange/Socket ends as per requirement ISI Marked including bolts, nuts and jointing materials complete of the size 80 mm complete all as specified and as directed. |
| 75 | Dismantling the existing unserviceable Foot Valve complete and S & F Cast iron Foot Valve Ball type with flange/Socket ends as per requirement ISI Marked including bolts, nuts and jointing materials complete of the size 100 mm complete all as specified and as directed. |
| 76 | Cleaning of valve pit chamber of any size by taking out mud and muddy water and depositing the same to a distance n. exc 20 meter from the pit including swiping, free from any type of dirt including rectification of the leakage of valve of any size with glands of appropriate size and required packing materials complete all as specified and dircted by Engr-in-Charge at site. |
| 77 | Material & labour for run lead joints for spigot and socket CI pipes/ fittings including spun yarn complete for pipe of size 80 mm bore complete all as specified and directed Note :- Rate inclusive of necessary excavation,returning filling for making lead joints up to 1.5 mtr deep. |
| 78 | All as per item No 34 above but Bore of pipe 100 mm. |
| 79 | All as per item No 34 above but Bore of pipe 150 mm. |
| 80 | Dismantling the existing unserviceable M S Pipe complete. Supply and lay M S Pipes heavy grade with all fittings laid in floors,Pillar or fixed to walls and ceilings etc of size 150 mm dai |
| 81 | Cutting the existing M S pipe line of 150 mm die pumping /distribution line, inserting Tee and connectiing and jointing complete all as directed. |
| 82 | Supply and fix Ball bsass valve(float valves), high pressure, with polythene, float and flynut complete,screwed for iron pipe of size 25 mm bore complete. |
| 83 | Description all as per item No 39 above but of size 20 mm bore. |
| 84 | Description all as per item No 39 above but of size 15 mm bore. |
| 85 | M&L for for boring/drilling by machines/ manual horizontally under the road in any type of soil without cutting/ disturbing the existing road and inserting GI /DI Pipe of any size complete all as specified and directed .Note:- GI pipe shall be measured and paid seperately. |
| 86 | M&L preparing old painted steel surface of pipe, applying two coats of synthetic enamel paint of Motor,pump,inlet and outlet pipes (as per MES colpur code) complete all as specified and directed by Engineer-in-charge. |
| 87 | M&L for rewinding of centrifugal pump set motor 15/12.5 HP 3 phase 415 volts 50 Hz. by dismantling and removing the burnt out copper winding cleaning the slots of stator thoroughly and rewinding the stator with polyester based copper wire of the same gauge with ‘E’ class of insulation and applying varnish, earring the stator winding and assembling all parts of motor and pump including testing after connecting up with starter complete all as specified and directed by Engineer-in-charge. |
| 88 | M&L rewinding of centrifugal pump set motor 20 HP 3 phase 415 volts 50 Hz. by dismantling and removing the burnt out copper winding cleaning the slots of stator thoroughly and rewinding the stator with polyester based copper wire of the same gauge with proper insulation and applying varnish, earring the stator winding and assembling all parts of motor and pump including testing after connecting up with starter complete all as specified and directed by Engineer-in-charge. |
| 89 | M&L rewinding of centrifugal pump set motor 25 to 40 HP 3 phase 415 volts 50 Hz. by dismantling and removing the burnt out copper winding cleaning the slots of stator thoroughly and rewinding the stator with polyester based copper wire of the same gauge with proper insulation and applying varnish, earring the stator winding and assembling all parts of motor and pump including testing after connecting up with starter complete all as specified and directed by Engineer-in-charge. |
| 90 | Supply only Ball bearing (2 Nos) for front and rear side of centrifugal pump set, of capacity 40HP complete all as specified and as directed by the Engr-in-Charge. MAKE : As per Sample/OEM or as decided by the Engr-In-Charge/GE. |
| 91 | Material and labour for Reconditioning of impeller of any type for centrifugal pump set, of capacity 12.5 to 40HP complete all as specified and as directed by the Engr-in-Charge. MAKE : As per Sample/OEM or as decided by the Engr-In-Charge/GE. |
| 92 | Supply & Fix stainless steel shaft and new brass bush of appropriate size suitable for centrifugal pump set of capacity 15 to 60 HP including any type lathe work for fixing bearing, bush, CI/Gun Metal bush etc complete all as specified and directed. Please Enable Macros to View BoQ information |
| 93 | Supply & Fix stainless steel shaft and new brass bush of appropriate size suitable for centrifugal pump set of capacity 15 to 60 HP including any type lathe work for fixing bearing, bush, CI/Gun Metal bush etc complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysSep 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender