Tender For Provn Of Attached Toilet (Including Urinal) Cum Bathroom With Building No P-13 At Cqa (Ffe & Nbce), Aundh C Pune-27
Tender Value
Ref. Documents
Estimated cost
Bid Submission
29 Aug 2026
5 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Attached Toilet (Including Urinal) Cum Bathroom With Building No P-13 At Cqa (Ffe & Nbce), Aundh C Pune-27
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft and loose soil. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose type of soil all as specified and directed. |
| 3 | Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil all as directed and specified. |
| 4 | Removing surplus excavated material (soil) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. |
| 5 | M & L for plain cement concrete, 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 6 | M&L for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete |
| 7 | M&L for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates Columns, pillars, piers, posts and struts |
| 8 | M&L for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates roof Beams, cantilevers, bressummers, lintels over 1.5m span |
| 9 | M&L for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates in roof Slab supported in walls beams and columns in roof ,Landing, balconies, deck slabs and in shelves and similar work complete all as specified and as directed. |
| 10 | M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces |
| 11 | M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions Square, Circular rectangular on plan or polygonal |
| 12 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.on flat rough surface |
| 13 | M&L for Formwork to soffits of suspedded slabs such as roof slabs, floor slabs landings and similar work ,vertical or to batter for rough finished flat surfaces of concrete complete. |
| 14 | M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement) |
| 15 | M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement) |
| 16 | M&L for rendering 10mm thick in cement mortar 1:3 on ceiling surface, finished even and smooth without using extra cement complete. |
| 17 | M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 18 | M & L for mild steel TMT bars 6 mm to 8 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 19 | M & L Precast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified. |
| 20 | M & L for PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate), as in lintels upto 1.5 m clear span, cills, steps,seismic and other similar bands, plinth course, string courses, lacinng courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed. |
| 21 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering |
| 22 | M&L Hardcore of broked stone or boulder gauge exc 63mm but n. exc 100mm, deposited , spread and levelled in layers n.exec 15 cm thick, watered and rolled/rammed to a tue surface complete all as specified. |
| 23 | M&L 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded agg) in sub base of floor is to be rough finished complete all as specified and directed. |
| 24 | M & L for 75mm thick, PCC (1:3:6), Type C-1, using 20mm graded stone aggregate as in Plinth protection etc surface finished even and fairwithout using extra cement including necessary form work if required, provision of vertical joints at 2 mtr centre to centre all as directed by Engr -in- charge. |
| 25 | M & L for Non Skid Ceramic tiles, Coloured, of size exceeding 0.06 Sqm and not exceeding 0.11 Sqm,7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. |
| 26 | M & L for Glazed Ceramic Coloured tiles of size 300mmX600mmX7mm as in Vertical Surfaces such as Skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat of 10mm thick in cement mortar 1:4 in complete all as specified and as directed. |
| 27 | S&F aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. including taking down existing steel ventilator incl taking down ol ventilator all as directed by Engr-in-Charge. |
| 28 | S&F aluminium powder coated window sliding type (3 track) with frame size 100x35x1.20mm and shutter 39.40x17.70x1.20mm with two glass shutter and one stainless steel wire mesh shutter including necessary jointing cleats, glazing clips, rubber packing powder coated aluminium snap beading screws with 4mm plain float glass and 0.56mm dia SS wire mesh, fittings etc, and necessary locking arrangements and including making good the jambs and painting with matching type and shade including taking down existing steel window all as directed by Engr-in-Charge. |
| 29 | S & F Solid coloured PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and as directed. |
| 30 | S & F Factory made coloured solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC \\"C\\" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in frame at site as per specification & drawing of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and as directed. |
| 31 | S & F Aluminium anodised barrel ower Bolt of size 150 mm size of extruded section complete all as specified and as directed. |
| 32 | S & F Aluminium cast type anodised Handle, size 150mm long complete all as specified and as directed. |
| 33 | S & F 100 mm size, heavy weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed. |
| 34 | S & F Aluminum aodised sliding door bolts, bearing ISI mark, 300mm long with hasp and staple(bolt type) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. |
| 35 | M&L for applying two coats of cement base paint on plastered surfaces of walls including preparation of new surface complete all as specified and directed. |
| 36 | M & L applying three coats of white wash to newly plastered surface of ceiling including preparation. |
| 37 | M & L applying two coat of oil bound distemper over a coat of primer to newly plastered surface including preparation of new plastered surfaces to wall all as specified and directed. |
| 38 | S&F 20mm bore GI tubes, medium grade, galvanised , with all fitting & fixed complete to walls & ceilings or laid in floors all as specified and as directed |
| 39 | S & F 15 mm bore tubes, medium grade, galvanised, with all fitting & fixed complete to walls & ceiling or laid in floors, all as specified and as directed [The rate is deemed to be included for concealing of GI tubes wherever required and directed]. |
| 40 | S&F for looking mirror of any size n.exc 2.00 sqm & 5mm thick mirror of selected quality glass,,mounted on 6mm thick commercial plywood and bevelled edge fixed on wall with six nos. stainless steel studs decorative type complete all as specified and as directed by the Engineer-in-Charge (make Modi Guard/Saint Globin and eql. ) |
| 41 | S&F fancy type two way Bib cock 15mm dia , fancy type, chromium plated with capstan or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and suitable for 15 bore of pipe fixed all as specified and directed (Make :Jaquar/Hindware/Cera/Prayag or equivalent). |
| 42 | S & F for fancy type CP brass angular stop cock 15 mm dia all as per directed (Make :Jaquar/Hindware/Cera/Prayag or equivalent). |
| 43 | S & F PVC connection of 600 mm length, suitable for 15 mm bore pipe with PTMT nuts, complete all as specified and directed. |
| 44 | S&F fancy type heavy duty health faucet chromium plated (ABS Body) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook fixing to 15 mm bore of pipe all as specified and directed.(Make :Jaquar/Hindware/Cera/Prayag or equivalent). |
| 45 | S&F CP grating ring or frame square or round 100mm size complete all as specified and directed. |
| 46 | S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) |
| 47 | S&F Plastic water closet seat cover (any colour) closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device all as directed. |
| 48 | S & F PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, white/coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed. |
| 49 | S&F Wash basins, vitreous China (flat back or angle back type) size 580X450mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing and supply of waste pipe all as specified |
| 50 | S&F Vitreous china bowl urinal hallf stall type white, with grating and union for discharge pipe fixed in repairs (excluding flushing cistern, flush pipe and waste pipe) all as specified. |
| 51 | S&F PVC (SWR) pipes 110mm dia ,single socketed in any length with rubber ring joints laid in trenches or floor & wall complete all as directed. |
| 52 | S&F PVC (SWR) pipes 75 mm dia ,single socketed in any length with rubber ring joints fixed and laid in trenches or floor/ceiling and wall all as directed. |
| 53 | S&F 15 mm dia fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified. |
| 54 | S&F PVC (SWR) bends any radius, 75mm dia pipe. |
| 55 | S&F PVC (SWR) branch piece 110 mm bore, single Y equal or unequal all as specified and directed. |
| 56 | S&F PVC (SWR) junction 110mm bore single T equal or unequal all as specified and directed. |
| 57 | S&F in repairs Powder coated Alu grill of approved pattern using channel of required size, screwed to windows & ventilators with self tapping screws all as specified & directed |
| 58 | M&L 20mm Granite work (table rubbed and polished) in steps, jambs, cills, WHB platforms,counter tops and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 20mm Screed bed in CM 1:4, all as specified and directed.Note : The rate quoted is deemed to be included for full moulding of edges and making, opening for kitchen sink all as directed by Engr-in-Charge. |
| 59 | Cutting chases, pinning in concrete block walls, making good to facing where required and pointing in cement mortar (1:3) and making good , cutting n.exc 10cm girth all as specified and directed. |
| 60 | S&F for towel ring chromium plated brass fancy type complete all as specified and as directed by the Engineer-in-Charge. (Make :Jaquar/Hindware/Cera/Prayag or equivalent). |
| 61 | S/F for sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long all as specified and directed. |
| 62 | S & F Rotational moulded Polythene [HDPE] Water Tanks, Cylindrical & Vertical Type 500 Liters Capacity double layered 'ISI' marked, hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete icomplete all as specified and as directed. |
| 63 | S&F 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) |
| 64 | M&L for applying roof treatment as under :- |
| 65 | Providing 10mm thick (average) rendering in cement mortar 1:3 mixed with WPC as per manufacturer's instruction (to be measured separately as supply only) for levelling to a true surface and to receive new roof treatment complete. |
| 66 | Providing a coat of bitumen primer @ 0.40 Litre/Sqm over plastered surfaces of roof including parapet surfaces. |
| 67 | Providing one layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm, reinforced with polyester non woven fabric (weighing not less than 150 Gms/Sqm). Polymeric membrane shall be taken to a height 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note:(a) Laying of APP based polymeric membrane shall be done by torch application method or as per manufacturar's instruction. (b) Side overlaps shall be minimum 75mm and end laps shall be minimum 100mm and sealing all overlaps and joints as manufacturer's instructions. (c) The make of polymeric membrane shall be as per PS Specification of CA. |
| 68 | Applying two coats of bituminous aluminium paint on top of APP membrane. |
| 69 | S&F in repair (any type & size of door) aluminium anodised door with frame and shutter and glazing 5 mm thick tinted glass or 12 mm thick prelaminated particle board exterior grade in panels, rubber gasket, aluminium glazing clips, mortice lock, Aluminium stopper cleat, hydraulic double action floor door spring, iron mongary etc. section of aluminium door including powder coating of any colour (min thickness of powder coating 50 micron) shall be of following sizes:-Frame : 100 x 44 x 1.80 mm thick with rawal plugMiddle lock rail: 100 x 44 x 1.80 mm thickBottom rail : 100 x 44 x 1.80 mm thickTop rail / Style: 46 x 44 x 1.80 mm thickGlazing beading: 0.70 mm thickAluminium handle 'D' type: 150 mm Aluminium tower bolt 9.9 mm dia shoot 200 mm long Mortice lock – 100 mm 4 lever,Aluminium stopper cleat Note :- (i) Making good of wall surface with matching to existing surface complete all as specified and directed.(ii) Making good floor surface after fixed hydraulic double action floor door spring with matching to existing surface complete all as specified and directed. |
| 70 | RCC NP3 150 MM dia Pipes laid on 150 mm thick bed and depth 0.70m to 1.65m with excavation in any type of soil,including manholes/drop manhole of standard size made of of brick masonary /RCC/precast RCC with SFRC ventilation cover and frame.including all item and activities to excute and make sewer line functional. |
| 71 | Hume pipe Septic Tank designed to carry sewage and sullage water ,excavation in any type of soil,pcc(1:4:8) below foundation,with vent shaft,manhole opening with cover connection etc, for 10 users |
| 72 | Soakage wells exc,in ordinary soil,foundation in PCC 1:3:6 ,wells of honey combed and solid in M-25 concrete,including intercepting chamber,screen chamber Brick work in CM,RCC cover slab in M-25/RR masonary/Filling with brick bats ,complete of size (1.2 m dia x 3.0 M deep) for 10 users. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender